Add support for raw VBI capture for the em28xx bridge, currently only for
NTSC. Support for PAL capture to follow shortly (including the removal of
numerous hard-coded NTSC-specific sizes for capture buffers, etc).
Note that the code currently changes the default current norm from PAL to
NTSC (so that zvbi-ntsc-cc works properly). The default norm really should
be moved into a board-level parameter.
This work was sponsored by EyeMagnet Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add code enabling the VBI registers for variants of the em28xx chip that
support VBI, and make sure the isoc streaming code continues to work for
the video component of the stream (note the video and vbi data arrive
intermixed on the same isoc pipe).
Note that this version just drops the actual VBI data onto the floor as
opposed to processing it. The "#ifdef 0" tags are for the videobuf code that
appears in the next patch in this series.
We created a separate version of the isoc_copy version for parsing the version
of the stream that includes VBI data. In theory, they might be able to be
merged at some point in the future, but the initial goal is to ensure that we
do not cause any regressions with devices that do not have VBI support.
This work was sponsored by EyeMagnet Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, the logic to load ir i2c ancillary module is broken. It is
associated to Hauppauge devices with IR flag on their eeprom, no matter
if the device uses i2c or em28xx direct IR support. That's wrong.
Instead, add a flag to the boards that use i2c IR chips and load the
module only for those devices and if ir is not disabled.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ir-kbd-i2c's ir_probe() function can be called much later (i.e. at
ir-kbd-i2c module load), than the lifetime of a struct IR_i2c_init_data
allocated off of the stack in cx18_i2c_new_ir() at registration time.
Make sure we pass a pointer to a persistent IR_i2c_init_data object at
i2c registration time.
Thanks to Brian Rogers, Dustin Mitchell, Andy Walls and Jean Delvare to
rise this question.
Before this patch, if ir-kbd-i2c were probed after em28xx, trash data
were used. After the patch, no matter what order, it is properly
reported as tested by me:
input: i2c IR (i2c IR (EM2840 Hauppaug as /class/input/input10
ir-kbd-i2c: i2c IR (i2c IR (EM2840 Hauppaug detected at i2c-4/4-0030/ir0 [em28xx #0]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, V4L uses a scancode table whose index is the scancode and
the value is the keycode. While this works, it has some drawbacks:
1) It requires that the scancode to be at the range 00-7f;
2) keycodes should be masked on 7 bits in order for it to work;
3) due to the 7 bits approach, sometimes it is not possible to replace
the default keyboard to another one with a different encoding rule;
4) it is different than what is done with dvb-usb approach;
5) it requires a typedef for it to work. This is not a recommended
Linux CodingStyle.
This patch is part of a larger series of IR changes. It basically
replaces the IR_KEYTAB_TYPE tables by a structured table:
struct ir_scancode {
u16 scancode;
u32 keycode;
};
This is very close to what dvb does. So, a further integration with DVB
code will be easy.
While we've changed the tables, for now, the IR keycode handling is still
based on the old approach.
The only notable effect is the redution of about 35% of the ir-common
module size:
text data bss dec hex filename
6721 29208 4 35933 8c5d old/ir-common.ko
5756 18040 4 23800 5cf8 new/ir-common.ko
In thesis, we could be using above u8 for scancode, reducing even more the size
of the module, but defining it as u16 is more convenient, since, on dvb, each
scancode has up to 16 bits, and we currently have a few troubles with rc5, as their
scancodes are defined with more than 8 bits.
This patch itself shouldn't be doing any functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[mchehab@redhat.com: Fix a few wrong IR keymaps]
Signed-off-by: Shine Liu <shinel@foxmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[mchehab@redhat.com: fix merge conflict and a few CodingStyle issues]
Signed-off-by: Steve Gotthardt <gotthardt@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to historical reasons, em28xx driver gets two consecutive frames and
fold them into an unique framing, doing interlacing. While this works
fine for TV images, this produces two bad effects with webcams:
1) webcam images are progressive. Merging two consecutive images produce
interlacing artifacts on the image;
2) since the driver needs to get two frames, it reduces the maximum
frame rate by two.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Depending on the video input format, vinmode/vinctl needs adjustments.
For TV, this is not relevant, since the supported decoders output data
at the same format. However, webcam sensors may have different formats,
so, this needs to be adjusted based on the device.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In order to properly estimate fps, mt9v011 sensor driver needs to know
what is the used frequency on the sensor cristal. Adds the proper fields
and initialization code for specifying the cristal frequency.
Also, based on experimentation, it was noticed that the Silvercrest is
outputing data at 7 fps. This means that it should be using a 6.3 MHz
cristal. This information needs to be double checked later, by opening
the device. Anyway, by using this value for xtal, at least now we have
the correct fps report.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While trying to fix an mt9v001 webcam, I noticed that HSCALE/VSCALE do
work with em28xx + webcam. The issue is that the scaling setup depends
on the number of visible rows/cols of the input image.
With mt9v011 (Silvercrest), the resolution is 640x480. So, the scaling
is different from a normal TV image (720x480 on NTSC). This were causing
a wrong scaling and a previous patch disabled scaling.
As each sensor have their different resolution setting, the xres/yres
should be adjusted accordingly with the input sensor.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of using em28xx board decoder field for storing sensor information,
let's use instead a separate field for it.
Also, as sensors are currently autodetected, there's no need of having
it at the boards description. So, move it to the main em28xx struct.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Just renames the flag, to use a clearer name. Later patches will use
this flag to properly set some drivers behaviors for webcams.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This webcam uses a em2710 chipset, that identifies itself as em2820,
plus a mt9v011 sensor, and a DY-301P lens.
It needs a few different initializations than a normal em28xx device.
Thanks to Hans de Goede <hdegoede@redhat.com> and Douglas Landgraf
<dougsland@redhat.com> for providing the acces for the webcam during
this weekend, I could make a patch for it while returning back from
FISL/Fudcom LATAM 2009.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for the EVGA inDtube. Both ATSC and analog side validated as
fully functional.
Thanks to Jake Crimmins from EVGA for providing the correct GPIO info.
Thanks to Alan Hagge for doing all the device testing.
Thanks to Greg Williamson for providing hardware for testing.
Cc: Jake Crimmins <jcrimmins@evga.com>
Cc: Alan Hagge <ahagge@gmail.com>
Cc: Greg Williamson <cheeseboy16@gmail.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make the KWorld 2800d work properly. In this case, that means making the
profile more generic so that it works for both the Pointnix Intra-Oral USB
camera and the KWorld device.
The device provides the audio through a pass-thru cable, so we don't need
an actual audio capture profile (neither the K-World device nor the Pointnix
have an onboard audio decoder).
Thanks to Paul Thomas for providing sample hardware.
Cc: Paul Thomas <pthomas8589@gmail.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For specific boards, pass initialization data to ir-kbd-i2c instead
of modifying the settings after the device is initialized. This is
more efficient and easier to read.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Let card drivers probe for IR receiver devices and instantiate them if
found. Ultimately it would be better if we could stop probing
completely, but I suspect this won't be possible for all card types.
There's certainly room for cleanups. For example, some drivers are
sharing I2C adapter IDs, so they also had to share the list of I2C
addresses being probed for an IR receiver. Now that each driver
explicitly says which addresses should be probed, maybe some addresses
can be dropped from some drivers.
Also, the special cases in saa7134-i2c should probably be handled on a
per-board basis. This would be more efficient and less risky than always
probing extra addresses on all boards. I'll give it a try later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The em28xx actually has a register that tells the driver what the maximum
packet size is (based on a value programmed into the eeprom). Make use of
that register instead of assuming a hardcoded value of 564 (since 564 is not
correct for devices that do QAM such as the KWorld 340u).
Note that for now the em2874 code isn't there, falling back to the 564 value,
however this is not a problem since there are not any em2874 based devices in
the current v4l-dvb tree).
Thanks to Jarod Wilson for detecting the initial problem and figuring out that
the isoc configuration was wrong for his device.
Cc: Jarod Wilson <jarod@wilsonet.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Added EmpireTV entry.
Thanks to Xwang <xwang1976@email.it> to provide data for this board.
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Converted em28xx driver to v4l2_subdev.
Thanks to Hans Verkuil <hverkuil@xs4all.nl> for helping this conversion.
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Compro VideoMate uses an external audio DSP chip, controlled via tvaudio
module (tda9874a). This patch improves em28xx infrastructure to support
an external audio processor and fixes the Compro VideoMate entry to work
with it.
Signed-off-by: Vitaly Wool <vital@embeddedalley.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Removed EM2821_BOARD_PROLINK_PLAYTV_USB2 entry.
This entry has a incorrect tuner set.
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by Vitaly Wool <vital@embeddedalley.com>:
> about half a year ago I posted the patch that basically enabled Compro
> VideoMate For You USB TV box support.
> The main problem is I couldn't get the sound working.
> So I kind of decomposed the box and found out the audio decoder chip
> used there was Philips TDA9874A. As far as I can see, it's not supported
> within the em28xx suite although it is for other TV tuner drivers.
A tvaudio modprobing confirms that tda9874a chip is accessible via i2c:
tvaudio: TV audio decoder + audio/video mux driver
tvaudio: known chips: tda9840, tda9873h, tda9874h/a, tda9850, tda9855, tea6300, tea6320, tea6420, tda8425, pic16c54 (PV951), ta8874z
tvaudio' 1-0058: chip found @ 0xb0
tvaudio' 1-0058: tvaudio': chip_read2: reg254=0x11
tvaudio' 1-0058: tvaudio': chip_read2: reg255=0x2
tvaudio' 1-0058: tda9874a_checkit(): DIC=0x11, SIC=0x2.
tvaudio' 1-0058: found tda9874a.
tvaudio' 1-0058: tda9874h/a found @ 0xb0 (em28xx #0)
tvaudio' 1-0058: tda9874h/a: chip_write: reg0=0x0
tvaudio' 1-0058: tda9874h/a: chip_write: reg1=0xc0
tvaudio' 1-0058: tda9874h/a: chip_write: reg2=0x2
tvaudio' 1-0058: tda9874h/a: chip_write: reg11=0x80
tvaudio' 1-0058: tda9874h/a: chip_write: reg12=0x0
tvaudio' 1-0058: tda9874h/a: chip_write: reg13=0x0
tvaudio' 1-0058: tda9874h/a: chip_write: reg14=0x1
tvaudio' 1-0058: tda9874h/a: chip_write: reg15=0x0
tvaudio' 1-0058: tda9874h/a: chip_write: reg16=0x14
tvaudio' 1-0058: tda9874h/a: chip_write: reg17=0x50
tvaudio' 1-0058: tda9874h/a: chip_write: reg18=0xf9
tvaudio' 1-0058: tda9874h/a: chip_write: reg19=0x80
tvaudio' 1-0058: tda9874h/a: chip_write: reg20=0x80
tvaudio' 1-0058: tda9874h/a: chip_write: reg24=0x80
tvaudio' 1-0058: tda9874h/a: chip_write: reg255=0x0
tvaudio' 1-0058: tda9874a_setup(): A2, B/G [0x00].
tvaudio' 1-0058: tda9874h/a: thread started]
This patch automatically loads tvaudio when needed (currently, only
with this board).
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Lots of coding style fixes and a typo correction for em28xx.
[dougsland@redhat.com: fixed a reject due to a change on em28xx-audio.c]
Signed-off-by: Nicola Soranzo <nsoranzo@tiscali.it>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Essentially if a snd_em28xx_capture_trigger() stop followed by a snd_em28xx_capture_trigger() start would not yield any
data because there was some logic put in with an adev->shutdown variable which did not seem warranted in my humble opinion.
It would cause snd_em28xx_capture_trigger start never to start up the audio stream until the device was closed and
reopened again. Upon re-opening the device adev->shutdown is reset and audio data would again flow.
Signed-off-by: Robert Krakora <rob.krakora@messagenetsystems.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Added entry for GADMEI TVR200.
Thanks to Yohanes Nugroho <yohanes@gmail.com> for testing and data collection.
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix for KWorld 330U Board
Many thanks to Devin and Mauro!!!
Signed-off-by: Robert Krakora <rob.krakora@messagenetsystems.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some em28xx devices use the PCM IN AC 97 PIN for digital audio. However,
currently, the PCM IN selection is not set by the driver. This patch allows
specifying the PCM IN expected output, via board description table.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some devices require different setups on struct_audio. Due to that, we
may need to change some fields at dev.adev during device probe. So, this
patch moves the dynamic memory allocation of adev at em28xx-alsa to the
dynamic allocation of struct em28xx dev that happens during device
probe.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Introduce a struct v4l2_file_operations for v4l2 drivers.
Remove the unnecessary inode argument.
Move compat32 handling (and llseek) into the v4l2-dev core: this is now
handled in the v4l2 core and no longer in the drivers themselves.
Note that this changeset reverts an earlier patch that changed the return
type of__video_ioctl2 from int to long. This change will be reinstated
later in a much improved version.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Pinnacle 80e cannot be supported since Micronas yanked their driver
support for the drx-j chipset at the last minute. Remove the device profile
since it cannot work without the drx driver and it being there is only likely
to confuse people into thinking the device is supported but not working.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The DVC 100 profile is redundant since we already have an existing identical
profile named "Pinnacle Dazzle DVC 90/DVC 100"
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now, just two routines are enough for analog: the first one configs the analog
part and register V4L2 devices, and the second one release analog devices.
After this patch, it will be easier to transform em28xx-video into an em28xx
extension, loaded only on analog devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
em28xx-video were holding several code that are not specific to V4L2
interface.
This patch moves the core code for em28xx-core, and usb probing code
into em28xx-cards.
This opens the possibility of breaking em28xx into a core module and a
V4L2 module, loaded only on devices that have analog interfaces.
Some cleanup may be done at em28xx-cards to optimize the config code.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The em28xx driver can be coupled to an anciliary AC97 chip. This patch
allows read/write AC97 registers directly.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch uses the same code for enumberating video formats that are
present on cx88, bttv and saa7134 drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Several chips may be turned off when the device is not used, like audio,
video and dvb demods. This patch adds a gpio callback at the core
structs to allow turning off such devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
