It doesn't make sense to handle an IR code given before
suspending after the device resume. So, turn off IR
int while suspending.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As the RC kthread can re-enable IR int, we should first
cancel the kthread and then disable IR int.
While here, remove a temporary debug printk.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When the DVB code sets the frontend, it disables the IR
INT, probably due to some hardware bug, as there's no code
there at au8522 frontend that writes on register 0xe0.
Fixing it at au8522 code is hard, as it doesn't know if the
IR is enabled or disabled, and just restoring the value of
register 0xe0 could cause other nasty effects. So, better
to add a hack at au0828-input polling interval to enable int,
if disabled.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The IR code increases the power consumption of the device.
Allow to disable it via modprobe parameter.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This sleep was doing some debouncing on the original driver.
This is not needed on Linux, because the RC core and the input
layer already takes care of it.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull networking updates from David Miller:
"Highlights:
1) Steady transitioning of the BPF instructure to a generic spot so
all kernel subsystems can make use of it, from Alexei Starovoitov.
2) SFC driver supports busy polling, from Alexandre Rames.
3) Take advantage of hash table in UDP multicast delivery, from David
Held.
4) Lighten locking, in particular by getting rid of the LRU lists, in
inet frag handling. From Florian Westphal.
5) Add support for various RFC6458 control messages in SCTP, from
Geir Ola Vaagland.
6) Allow to filter bridge forwarding database dumps by device, from
Jamal Hadi Salim.
7) virtio-net also now supports busy polling, from Jason Wang.
8) Some low level optimization tweaks in pktgen from Jesper Dangaard
Brouer.
9) Add support for ipv6 address generation modes, so that userland
can have some input into the process. From Jiri Pirko.
10) Consolidate common TCP connection request code in ipv4 and ipv6,
from Octavian Purdila.
11) New ARP packet logger in netfilter, from Pablo Neira Ayuso.
12) Generic resizable RCU hash table, with intial users in netlink and
nftables. From Thomas Graf.
13) Maintain a name assignment type so that userspace can see where a
network device name came from (enumerated by kernel, assigned
explicitly by userspace, etc.) From Tom Gundersen.
14) Automatic flow label generation on transmit in ipv6, from Tom
Herbert.
15) New packet timestamping facilities from Willem de Bruijn, meant to
assist in measuring latencies going into/out-of the packet
scheduler, latency from TCP data transmission to ACK, etc"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1536 commits)
cxgb4 : Disable recursive mailbox commands when enabling vi
net: reduce USB network driver config options.
tg3: Modify tg3_tso_bug() to handle multiple TX rings
amd-xgbe: Perform phy connect/disconnect at dev open/stop
amd-xgbe: Use dma_set_mask_and_coherent to set DMA mask
net: sun4i-emac: fix memory leak on bad packet
sctp: fix possible seqlock seadlock in sctp_packet_transmit()
Revert "net: phy: Set the driver when registering an MDIO bus device"
cxgb4vf: Turn off SGE RX/TX Callback Timers and interrupts in PCI shutdown routine
team: Simplify return path of team_newlink
bridge: Update outdated comment on promiscuous mode
net-timestamp: ACK timestamp for bytestreams
net-timestamp: TCP timestamping
net-timestamp: SCHED timestamp on entering packet scheduler
net-timestamp: add key to disambiguate concurrent datagrams
net-timestamp: move timestamp flags out of sk_flags
net-timestamp: extend SCM_TIMESTAMPING ancillary data struct
cxgb4i : Move stray CPL definitions to cxgb4 driver
tcp: reduce spurious retransmits due to transient SACK reneging
qlcnic: Initialize dcbnl_ops before register_netdev
...
Pull media updates from Mauro Carvalho Chehab:
- removal of sn9c102. This device driver was replaced a long time ago
by gspca
- solo6x10 and go7007 webcam drivers moved from staging into
mainstream. They were waiting for an API to allow setting the image
detection matrix
- SDR drivers moved from staging into mainstream: sdr-msi3101 (renamed
as msi2500) and rtl2832
- added SDR driver for airspy
- added demux driver: si2165
- rework at several RC subsystem, making the code for RC-5 SZ variant
to be added at the standard RC5 decoder
- added decoder for the XMP IR protocol
- tuner driver moved from staging into mainstream: msi3101 (renamed as
msi001)
- added documentation for some additional SDR pixfmt
- some device tree bindings documented
- added support for exynos3250 at s5p-jpeg
- remove the obsolete, unmaintained and broken mx1_camera driver
- added support for remote controllers at au0828 driver
- added a RC driver: sunxi-cir
- several driver fixes, enhancements and cleanups.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (455 commits)
[media] cx23885: fix UNSET/TUNER_ABSENT confusion
[media] coda: fix build error by making reset control optional
[media] radio-miropcm20: fix sparse NULL pointer warning
[media] MAINTAINERS: Update go7007 pattern
[media] MAINTAINERS: Update solo6x10 patterns
[media] media: atmel-isi: add primary DT support
[media] media: atmel-isi: convert the pdata from pointer to structure
[media] media: atmel-isi: add v4l2 async probe support
[media] rcar_vin: add devicetree support
[media] media: pxa_camera device-tree support
[media] media: mt9m111: add device-tree suppport
[media] soc_camera: add support for dt binding soc_camera drivers
[media] media: soc_camera: pxa_camera documentation device-tree support
[media] media: mt9m111: add device-tree documentation
[media] s5p-mfc: remove unnecessary calling to function video_devdata()
[media] s5p-jpeg: add chroma subsampling adjustment for Exynos3250
[media] s5p-jpeg: Prevent erroneous downscaling for Exynos3250 SoC
[media] s5p-jpeg: Assure proper crop rectangle initialization
[media] s5p-jpeg: fix g_selection op
[media] s5p-jpeg: Adjust jpeg_bound_align_image to Exynos3250 needs
...
Here's the big driver-core pull request for 3.17-rc1.
Largest thing in here is the dma-buf rework and fence code, that touched
many different subsystems so it was agreed it should go through this
tree to handle merge issues. There's also some firmware loading
updates, as well as tests added, and a few other tiny changes, the
changelog has the details.
All have been in linux-next for a long time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlPf1XcACgkQMUfUDdst+ylREACdHLXBa02yLrRzbrONJ+nARuFv
JuQAoMN49PD8K9iMQpXqKBvZBsu+iCIY
=w8OJ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here's the big driver-core pull request for 3.17-rc1.
Largest thing in here is the dma-buf rework and fence code, that
touched many different subsystems so it was agreed it should go
through this tree to handle merge issues. There's also some firmware
loading updates, as well as tests added, and a few other tiny changes,
the changelog has the details.
All have been in linux-next for a long time"
* tag 'driver-core-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (32 commits)
ARM: imx: Remove references to platform_bus in mxc code
firmware loader: Fix _request_firmware_load() return val for fw load abort
platform: Remove most references to platform_bus device
test: add firmware_class loader test
doc: fix minor typos in firmware_class README
staging: android: Cleanup style issues
Documentation: devres: Sort managed interfaces
Documentation: devres: Add devm_kmalloc() et al
fs: debugfs: remove trailing whitespace
kernfs: kernel-doc warning fix
debugfs: Fix corrupted loop in debugfs_remove_recursive
stable_kernel_rules: Add pointer to netdev-FAQ for network patches
driver core: platform: add device binding path 'driver_override'
driver core/platform: remove unused implicit padding in platform_object
firmware loader: inform direct failure when udev loader is disabled
firmware: replace ALIGN(PAGE_SIZE) by PAGE_ALIGN
firmware: read firmware size using i_size_read()
firmware loader: allow disabling of udev as firmware loader
reservation: add suppport for read-only access using rcu
reservation: update api and add some helpers
...
Conflicts:
drivers/base/platform.c
Sometimes dev->tuner_type is compared to UNSET, sometimes to TUNER_ABSENT,
but these defines have different values.
Standardize to TUNER_ABSENT.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
make reset control optional for i.MX27
The patch "[media] coda: add reset control support" introduced a build failure
if CONFIG_RESET_CONTROLLER is disabled:
drivers/media/platform/coda.c:3734:2: error: implicit declaration of
function 'devm_reset_control_get'
Since not all SoCs containing CODA VPUs do have a system reset controller,
use devm_reset_control_get_optional to make it optional.
Reported-by: Shawn Guo <shawn.guo@linaro.org>
Reported-by: Olof's autobuilder <build@lixom.net>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch add the DT support for Atmel ISI driver.
It use the same v4l2 DT interface that defined in video-interfaces.txt.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Cc: devicetree@vger.kernel.org
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Now the platform data is initialized by allocation of isi
structure. In the future, we use pdata to store the dt parameters.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for devicetree probe for the rcar-vin
driver.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
[g.liakhovetski@gmx.de fix a typo, sort headers alphabetically]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add device-tree support for mt9m111 camera sensor.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add initial support for OF based soc-camera devices that may be used
by any of the soc-camera drivers. The driver itself will need converting
to use OF.
These changes allow the soc-camera driver to do the connecting of any
async capable v4l2 device to the soc-camera driver. This has currently
been tested on the Renesas Lager board.
It currently only supports one input device per driver as this seems
to be the standard connection for these devices.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
[g.liakhovetski@gmx.de add check for multiple subdevices]
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Tested-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Since we have get vdev by calling video_devdata() at the beginning of
s5p_mfc_open(), we should just use vdev instead of calling video_devdata()
again in the following code.
Signed-off-by: Zhaowei Yuan <zhaowei.yuan@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Take into account limitations specific to the Exynos3250 SoC,
regarding setting the chroma subsampling control's value.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
JPEG codec on Exynos3250 SoC produces broken raw image if a JPEG
image is decoded to YUV420 format and downscaled by a factor
greater than 2. Prevent this by asserting downscale ratio to 2.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Assure proper crop_rect initialization in case the user space
doesn't call S_SELECTION ioctl.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
V4L2_SEL_TGT_COMPOSE_DEFAULT switch case should select whole
available area of the image and V4L2_SEL_TGT_COMPOSE
should apply user settings.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The jpeg_bound_align_image function needs to know the context
in which it is called, as it needs to align image dimensions in
a slight different manner for Exynos3250, which crops pixels for
specific values in case the format is RGB.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When parsing JPEG header s5p_jpeg_parse_hdr function
should return immediately in case there was an error
while reading a byte.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds support for jpeg codec on Exynos3250 SoC to
the s5p-jpeg driver. Supported raw formats are: YUYV, YVYU, UYVY,
VYUY, RGB565, RGB565X, RGB32, NV12, NV21. The support includes
also scaling and cropping features.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
On a normal condition, no errors should happen at xc5000
firmware upload is done. So, print at the dmesg if something
bad happens.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Currently, firmware retry logic keeps reading from FS every
time during the retry logic. This is not needed. Instead,
only release the firmware read after success.
While here, make the non-debug messages less verbose, as it
only matters to the user if the firmware was successfully
loaded, or if some error happened.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
With the current code, if something bad happens during the
firmware init process, the device will keep trying forever,
and removing it would cause an OOPS.
Instead, try only a limited amount of time. If not, fails.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
HVR-950Q uses an I2C remote controller at address 0x47 (7-bits
notation). Add support for it.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The IR dprintk message that prints a RC5 decoding failure
is not much helpful, as it doesn't tell on what bit the
error occurred.
Add such information, in order to make the debug message
more useful.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
On some hardware (au0828/au8522), the hardware is broken with
regards to the initial pulse detection. So, the driver needs to
produce a fake start pulse. That limits the acceptable protocols,
as it is not possible to produce a fake pulse that would cover
all supported protocols.
So, allow the driver to explicitly set the allowed protocols.
If the driver doesn't specify, keep the old behavior.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Commits 21dc61d3c0 and 7a1dd50b89 reduced the board I2C
speed to 20 MHz by default, due to a I2C stretch issue:
while xc5000 uses i2c stretch when a command is sent to it,
au0828 doesn't support this feature.
However, this is needed only for Xceive tuners. The other
I2C devices can work at the max speed.
So, revert the workarounds at board level, handling it at
I2C level, only when talking with xc5000.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As reported by Kbuildtest:
In file included from drivers/media/usb/cx231xx/cx231xx-dvb.c:35:0:
drivers/media/dvb-frontends/si2165.h:57:9: warning: 'struct si2165_config' declared inside parameter list [enabled by default]
struct i2c_adapter *i2c)
^
drivers/media/dvb-frontends/si2165.h:57:9: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
drivers/media/usb/cx231xx/cx231xx-dvb.c:157:21: error: variable 'hauppauge_930C_HD_1113xx_si2165_config' has initializer but incomplete type
static const struct si2165_config hauppauge_930C_HD_1113xx_si2165_config = {
^
drivers/media/usb/cx231xx/cx231xx-dvb.c:158:2: error: unknown field 'i2c_addr' specified in initializer
.i2c_addr = 0x64,
^
drivers/media/usb/cx231xx/cx231xx-dvb.c:158:2: warning: excess elements in struct initializer [enabled by default]
drivers/media/usb/cx231xx/cx231xx-dvb.c:158:2: warning: (near initialization for 'hauppauge_930C_HD_1113xx_si2165_config') [enabled by default]
drivers/media/usb/cx231xx/cx231xx-dvb.c:159:2: error: unknown field 'chip_mode' specified in initializer
.chip_mode = SI2165_MODE_PLL_XTAL,
^
drivers/media/usb/cx231xx/cx231xx-dvb.c:159:15: error: 'SI2165_MODE_PLL_XTAL' undeclared here (not in a function)
.chip_mode = SI2165_MODE_PLL_XTAL,
^
drivers/media/usb/cx231xx/cx231xx-dvb.c:159:2: warning: excess elements in struct initializer [enabled by default]
.chip_mode = SI2165_MODE_PLL_XTAL,
^
drivers/media/usb/cx231xx/cx231xx-dvb.c:159:2: warning: (near initialization for 'hauppauge_930C_HD_1113xx_si2165_config') [enabled by default]
drivers/media/usb/cx231xx/cx231xx-dvb.c:160:2: error: unknown field 'ref_freq_Hz' specified in initializer
.ref_freq_Hz = 16000000,
^
drivers/media/usb/cx231xx/cx231xx-dvb.c:160:2: warning: excess elements in struct initializer [enabled by default]
drivers/media/usb/cx231xx/cx231xx-dvb.c:160:2: warning: (near initialization for 'hauppauge_930C_HD_1113xx_si2165_config') [enabled by default]
>> drivers/media/usb/cx231xx/cx231xx-dvb.c:163:21: error: variable 'pctv_quatro_stick_1114xx_si2165_config' has initializer but incomplete type
static const struct si2165_config pctv_quatro_stick_1114xx_si2165_config = {
^
drivers/media/usb/cx231xx/cx231xx-dvb.c:164:2: error: unknown field 'i2c_addr' specified in initializer
.i2c_addr = 0x64,
^
drivers/media/usb/cx231xx/cx231xx-dvb.c:164:2: warning: excess elements in struct initializer [enabled by default]
>> drivers/media/usb/cx231xx/cx231xx-dvb.c:164:2: warning: (near initialization for 'pctv_quatro_stick_1114xx_si2165_config') [enabled by default]
drivers/media/usb/cx231xx/cx231xx-dvb.c:165:2: error: unknown field 'chip_mode' specified in initializer
.chip_mode = SI2165_MODE_PLL_EXT,
^
>> drivers/media/usb/cx231xx/cx231xx-dvb.c:165:15: error: 'SI2165_MODE_PLL_EXT' undeclared here (not in a function)
.chip_mode = SI2165_MODE_PLL_EXT,
^
drivers/media/usb/cx231xx/cx231xx-dvb.c:165:2: warning: excess elements in struct initializer [enabled by default]
.chip_mode = SI2165_MODE_PLL_EXT,
^
>> drivers/media/usb/cx231xx/cx231xx-dvb.c:165:2: warning: (near initialization for 'pctv_quatro_stick_1114xx_si2165_config') [enabled by default]
drivers/media/usb/cx231xx/cx231xx-dvb.c:166:2: error: unknown field 'ref_freq_Hz' specified in initializer
.ref_freq_Hz = 24000000,
^
drivers/media/usb/cx231xx/cx231xx-dvb.c:166:2: warning: excess elements in struct initializer [enabled by default]
>> drivers/media/usb/cx231xx/cx231xx-dvb.c:166:2: warning: (near initialization for 'pctv_quatro_stick_1114xx_si2165_config') [enabled by default]
drivers/media/usb/cx231xx/cx231xx-dvb.c: In function 'dvb_init':
drivers/media/usb/cx231xx/cx231xx-dvb.c:731:3: warning: passing argument 1 of 'si2165_attach' from incompatible pointer type [enabled by default]
dev->dvb->frontend = dvb_attach(si2165_attach,
^
In file included from drivers/media/usb/cx231xx/cx231xx-dvb.c:35:0:
drivers/media/dvb-frontends/si2165.h:55:36: note: expected 'const struct si2165_config *' but argument is of type 'const struct si2165_config *'
static inline struct dvb_frontend *si2165_attach(
^
drivers/media/usb/cx231xx/cx231xx-dvb.c:764:3: warning: passing argument 1 of 'si2165_attach' from incompatible pointer type [enabled by default]
dev->dvb->frontend = dvb_attach(si2165_attach,
^
In file included from drivers/media/usb/cx231xx/cx231xx-dvb.c:35:0:
drivers/media/dvb-frontends/si2165.h:55:36: note: expected 'const struct si2165_config *' but argument is of type 'const struct si2165_config *'
static inline struct dvb_frontend *si2165_attach(
^
That happens because the frontend was disabled by .config, but the
si2165_attach void stub require those structs, and also the
drivers that call it.
While here, remove the duplicated info about the possible I2C
addresses.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Commit 958c7c7e65 ("[media] v4l2-ctrls: fix corner case in round-to-range code") broke
controls that use a negative range.
The cause was a s32/u32 mixup: ctrl->step is unsigned while all others are signed. So
the result type of the expression '(ctrl)->maximum - ((ctrl)->step / 2)' became unsigned,
making 'val >= (ctrl)->maximum - ((ctrl)->step / 2)' true, since '((u32)-128) > 128'
(if val = -128, maximum = 128 and step = 1).
So carefully cast (step / 2) to s32.
There was one cast of step to s32 where it should have been u32 because both offset and
step are unsigned, so casting to signed makes no sense there. You do need a cast to u32
there, because otherwise architectures that have no 64-bit division start complaining
(step is a u64).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Some vendors have their on keymap table that are used on
all (or almost all) models for that vendor.
So, instead of specifying the keymap table per USB ID,
let's use the Vendor ID's table by default.
At the end, this will mean less code to be added when newer
devices for those vendors are added.
Of course, if rc_map is specified per board, it takes
precedence.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix the following warnings:
drivers/media/usb/cx231xx/cx231xx-cards.c: In function 'read_eeprom':
drivers/media/usb/cx231xx/cx231xx-cards.c:979:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for:
[2040:b130] Hauppauge WinTV 930C-HD (model 1113xx)
After loading the driver the first open to dvb device node fails.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is needed to support PCTV QuatroStick 522e which uses a si2157.
The si2157 driver is written using i2c_client attachment.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Tested-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The same card entry is used for HVR-4400 and HVR-5500.
Only HVR-5500 has been tested.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
DVB-T was tested with 8MHz BW channels in germany
This driver is the simplest possible, it uses automatic mode for all
parameters (TPS).
Added spectrum inversion support.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Tested-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of using some random value, return an error if the
PCB config is not available or doesn't match a know profile
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
That makes easier to understand the code. It would also help
to add support for having boards with just digital support
on some latter patch, as allowed by some PCB configs.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The initialization is already too complex. Use devm_ functions
to make the code simpler and easier to modify.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
On some newer boards, like HVR-930C HD, the information at
the PCB tables are sometimes higher than the ones actually
available on the device. That causes the probing code to
go past the interfaces array.
Add checks to the interface number before going past the
array.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This protocol is found on Dreambox remotes
[m.chehab@samsung.com: CodingStyle fixes and conflict fix]
Signed-off-by: Marcel Mol <marcel@mesa.nl>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Multiple pinctrl states are defined for 8, 16 and 24 data pin groups in PPI peripheral.
The driver should select correct group before set up further PPI parameters.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
On NOMMU architecture page fault is not triggered if a deleted list entry is
accessed without reinit.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
if the pinctrl driver is enabled.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fixes an old copy+paste bug that has survived all recent code
changes in this code area.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of counting the number of opened file handles, use function
v4l2_fh_is_singular_file() in em28xx_v4l2_open() and em28xx_v4l2_close() to
determine if the file handle is the first/last opened one.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of calling
...
struct v4l2_fh *fh = kzalloc(sizeof(*fh), GFP_KERNEL);
filp->private_data = fh;
v4l2_fh_init(fh, vdev);
v4l2_fh_add(fh);
...
simply use function v4l2_fh_open() which does all of these calls for us.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
struct em28xx_fh isn't needed anymore because the only used field which is left is struct v4l2_fh fh.
Use struct v4l2_fh directly and remvove struct em28xx_fh.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pointer v4l2" can be used instead of "dev->v4l2, which saves some characters.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Expression ((7bit i2c_addr << 1) & 0x01) can not be right
because it is always 0
Signed-off-by: Raimonds Cicans <ray@apollo.lv>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds the necessary IDs for the following dvb cards:
Digital Devices Octopus Mini
Digital Devices Cine S2 V6.5
Digital Devices DVBCT V6.1
Digital Devices Octopus V3
Mystique SaTiX-S2 V3
All these changes are taken from the official driver package by Digital
Devices.
http://download.digital-devices.de/download/linux/
[m.chehab@samsung.com: Fixed whitespace mangling]
Signed-off-by: Christopher Reimer <mail@creimer.net>
Tested-by: "D. Herrendoerfer" <d.herrendoerfer@herrendoerfer.name>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix checkpatch warning:
WARNING: usb_free_urb(NULL) is safe this check is probably not required
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Variable b is not initialized.
Only with a small chance it has random value 0xFF.
Remove if statement based on this value.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Tuner ID set into EEPROM is wrong, which causes driver to select
wrong tuner profile. That leads device non-working. Fix issue by
overriding known bad tuner IDs with suitable default value.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Patch originally written by Konrad. Rebased on current linux media tree.
Under Xen, vmalloc_32() isn't guaranteed to return pages which are really
under 4G in machine physical addresses (only in virtual pseudo-physical
addresses). To work around this, implement a vmalloc variant which
allocates each page with dma_alloc_coherent() to guarantee that each
page is suitable for the device in question.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: James Harper <james.harper@ejbdigital.com.au>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drx39xxj_set_lna() and drx39xxj_set_frontend() set LNA. Instead of
duplicating LNA configure code, change to use drxj_set_lna_state()
which sets LNA to the caller requested state (on or off).
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Several functions ignore the return values in error legs and always
return -EIO. This makes it hard to debug and take proper action in
calling routines.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drx39xyj driver lacks resume support. Add support by changing
its fe ops init interface to detect the resume status by checking
fe exit flag and do the necessary initialization. With this change,
driver resume correctly in both dvb adapter is not in use and in use
by an application cases.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Some fe drivers will have to do additional initialization
in their fe ops.init interfaces when called during resume.
Without the additional initialization, fe and tuner driver
resume fails. A new fe exit flag value DVB_FE_DEVICE_RESUME
is necessary to detect resume case. This patch adds a new
define and changes dvb_frontend_resume() to set it prior to
calling fe init and tuner init calls and resets it back to
DVB_FE_NO_EXIT once fe and tuner init is done.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Change drx39xyj_release() to check fe exit flag to detect the
device disconnect state and avoid accessing the device after
it has been removed.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Change em28xx_dvb_fini() to set fe exit flag to DVB_FE_DEVICE_REMOVED
when device is disconnected. em28xx maintains device disconnect status
in em28xx device. fe drivers will be able to now check the fe exit
status to avoid accessing the device, from their release interfaces
when called from disconnect path. This change depends on dvb-core
change that exports fe exit flag by moving it from fepriv to fe.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Some fe drivers attempt to access the device for power control from
their release routines. When release routines are called after device
is disconnected, the attempts fail. fe drivers should avoid accessing
the device, from their release interfaces when called from disconnect
path. dvb-frontend maintains exit flag to keep track when fe device is
disconnected in its private data structures. Export the flag in fe to
enable drivers to check the device status from their release interfaces.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In em28xx usb disconnect code path, some dvb fe and tuner drivers
attempt i2c transfers from their release interfaces. When device
is removed, return -ENODEV instead of attempting to transfer data
over i2c.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
em28xx uses resume interface as its reset_resume interface.
If usb device is reset during suspend, reset_resume doesn't
do the necessary initialization which leads to resume failure.
Many systems don't maintain do not maintain suspend current to
the USB host controllers during hibernation. Remove reset_resume
to allow disconnect to be called followed by device restore
sequence.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add error hanlding when EM2870_BOARD_KWORLD_A340 dvb_attach()
for fe and tuner fail in em28xx_dvb_init().
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
em28xx_dvb_resume() unregisters i2c tuner, i2c demod, and dvb.
This erroneous cleanup results in i2c tuner, i2c demod, and dvb
devices unregistered and removed during resume. This error is a
result of merge conflict between two patches that went into 3.15.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Added Sveon STV21 device based on Realtek RTL2832U and FC0013 tuner
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix regression in some dib0700 based devices.
Set size_of_priv, and don't call dvb_detach unnecessarily.
This resolves the oops(s) for my "Leadtek Winfast DTV Dongle (STK7700P based)"
Signed-off-by: James Harper <james.harper@ejbdigital.com.au>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If devm_request_threaded_irq() fails, we should better propagate the real error.
Also, print out the error code in the dev_err message.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
No need to return a 'fake' return value on platform_get_irq() failure.
Propagate the real error instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This tries to make them more like other remotes, and/or
the button labels.
Notably, the (>>) button is made KEY_FASTFORWARD, which is the
correct opposite of (<<)'s KEY_REVERSE. (It was KEY_FORWARD,
something else entirely.)
Likewise, KEY_STOP is the Sun keyboard "interrupt program" key;
the media key is KEY_STOPCD.
A restriction is that I try to avoid keycodes above 255, as the X11
client/server protocol is limited to 8-bit key codes. If not for
this, I would have used the KEY_NUMERIC_x codes for the numbers.
Signed-off-by: George Spelvin <linux@horizon.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
A more detailed description of what the buttons look like and
their intended function makes it easier for people to maintain
this code without access to the hardware.
[m.chehab@samsung.com: Fixed a typo "Mdeia" instead of "Media"]
Signed-off-by: George Spelvin <linux@horizon.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Since numerical order corresponds to top-left-to-bottom-right
order on the remote, this makes the table easier to read.
Signed-off-by: George Spelvin <linux@horizon.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There's no reason to use a LOCK prefix here.
Signed-off-by: George Spelvin <linux@horizon.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The KIND_FILTERED assignment of old_jiffies can't be merged, because
it must precede repeat handling.
Signed-off-by: George Spelvin <linux@horizon.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Get rid of the unnecessary "type" and "value" fields.
Signed-off-by: George Spelvin <linux@horizon.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Rather than having special code cases for diagonal mouse
movements, extend the general purpose code used for the
cardinal directions to handle arbitrary (x,y) deltas.
The deltas themselves are stored in translation table's "code"
field; this is also progress toward the goal of eliminating
the "value" element entirely.
Signed-off-by: George Spelvin <linux@horizon.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
It's not necessary, and since both events happen "at the same time"
in response to a single input event, the input device framework prefers
not to have it there.
(It's not a big deal one way or the other, but deleting cruft
is generally a good thing.)
Signed-off-by: George Spelvin <linux@horizon.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The variable types are simply larger than they need to be.
Shrink to signed and unsigned chars.
Signed-off-by: George Spelvin <linux@horizon.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
An input report is 4 bytes long, but there are only 12 bits
of actual payload. The 4 bytes are:
data[0] = 0x14
data[1] = data[2] + data[3] + 0xd5 (a checksum byte)
data[2] = the raw scancode (plus toggle bit in msbit)
data[3] = channel << 4 (the low 4 bits must be zero)
Ignore reports with a bad checksum.
Signed-off-by: George Spelvin <linux@horizon.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix various sparse warnings under drivers/media/rc/*.c, mostly
by making functions static.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Better to be coherent and prefix this file with rc-, in order to
help to identify to what subsystem it belongs.
This is in preparaton for a latter patch that will transform the
raw handling into a separate module.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
