Use dev_err() and co for messages from HD-audio controller and codec
drivers. The codec drivers are mostly bound with codec objects, so
some helper macros, codec_err(), codec_info(), etc, are provided.
They merely wrap the corresponding dev_xxx().
There are a few places still calling snd_printk() and its variants
as they are called without the codec or device context.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Incorrect ADC is picked in ca0132_capture_pcm_prepare(),
where it assumes multiple streams while there is one stream
per ADC. Note that ca0132_capture_pcm_cleanup() already does
the right thing.
The Chromebook Pixel has a microphone under the keyboard that
is attached to node id 0x8. Before this fix, recording would
always go to the main internal mic (node id 0x7).
Signed-off-by: Hsin-Yu Chao <hychao@chromium.org>
Reviewed-by: Dylan Reid <dgreid@chromium.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a HDMI stream is opened with the same stream tag
as a following opened stream to ca0132, audio will be
heard from two ports simultaneously.
Fix this issue by change to use snd_hda_codec_setup_stream
and snd_hda_codec_cleanup_stream instead, so that an
inactive stream can be marked as 'dirty' when found
with a conflict stream tag, and then get purified.
Signed-off-by: Hsin-Yu Chao <hychao@chromium.org>
Reviewed-by: Chih-Chung Chang <chihchung@chromium.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
'codec_send_command' is used only in this file. Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The char arrays with size 44 are for the name string of
snd_ctl_elem_id. Define the constant and replace the raw numbers with
it for clarifying better.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The DSP in the CA0132 codec adds a variable latency to audio depending
on what processing is being done. Add a new patch op to return that
latency for capture and playback streams. The latency is determined
by which blocks are enabled and knowing how much latency is added by
each block.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Turing on the headphone amp interferes with the impedance measurement
used to detect a TRRS style headset microphone. Delay the HP turn on
until 500ms after the jack is detected, allowing the mic detection
state machine to run to completion.
Signed-off-by: Chih-Chung Chang <chihchung@chromium.org>
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
spec->dsp_state is initialized to DSP_DOWNLOAD_INIT, no need to reset
and check it in ca0132_download_dsp().
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of using the dspload_is_loaded() function, check the dsp_state
that is kept in the spec. The dspload_is_loaded() function returns
true if the DSP transfer was never started. This false-positive leads
to multiple second delays when ca0132_setup_efaults() times out on
each write.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If dspload_image() fails, it was ignored and dspload_wait_loaded() was
still called. dsp_loaded should never be set to true in this case,
skip it. The check in dspload_wait_loaded() return true if the DSP is
loaded or if it never started.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the zero check `hda_frame_size_words == 0' before the modulus
`buffer_size_words % hda_frame_size_words'.
Also remove the redundant null check `buffer_addx == NULL'.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The chip address is 32bit long but INVALID_CHIP_ADDRESS is defined as
an unsigned long. This makes dsp_chip_to_dsp_addx() misbehaving on
64bit architectures. Fix the INVALID_CHIP_ADDRESS definition to be
32bit.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch fixes a few obvious bugs in DSP loader stuff:
- Fix possible memory leaks in the error path
- Avoid double-free calls in dma_reset()
- Properly set/unset WC bits for DMA buffers
- Add missing error status checks
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Base the DSP firmware transfer and communication timeouts on jiffy values.
Signed-off-by: Ian Minett <ian_minett@creativelabs.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sound/pci/hda/patch_ca0132.c: In function ‘ca0132_is_vnode_effective’:
sound/pci/hda/patch_ca0132.c:3331:15: warning: ‘nid’ may be used uninitialized in this function [-Wmaybe-uninitialized]
sound/pci/hda/patch_ca0132.c:4345:13: warning: ‘ca0132_download_dsp’ defined but not used [-Wunused-function]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
... to be less confusing for the update path.
This new kconfig will choose CONFIG_SND_HDA_DSP_LOADER, which is
basically a device-independent feature in hda_intel.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sound/pci/hda/patch_ca0132.c:387:19: sparse: symbol 'ca0132_voicefx' was not declared. Should it be static?
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sound/pci/hda/patch_ca0132.c: In function ‘ca0132_effects_set’:
sound/pci/hda/patch_ca0132.c:3391:2: warning: too many arguments for
format [-Wformat-extra-args]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Spotted by smatch,
sound/pci/hda/patch_ca0132.c:1950 dspxfr_image() error: potential
null dereference 'dma_engine'. (kzalloc returns null)
sound/pci/hda/patch_ca0132.c:1950 dspxfr_image() error: we
previously assumed 'dma_engine' could be null (see line 1857)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sound/pci/hda/patch_ca0132.c:1781 dspxfr_one_seg() info: why not
propagate 'status' from dsp_dma_stop() instead of (-5)?
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent update of ca0132 driver replaced the pinctl setup to the
direct write via snd_hda_codec_write() again. This should be covered
by snd_hda_set_pin_ctl() to be safer.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts commit c3b4eea262.
Since the recent firmware loader code supports caching at S3/S4 by
itself, we don't have to handle f/w caching in the driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Handle a potential dma_engine alloc error and fix the possible use of an
uninitialized status variable in dspxfr_one_seg(). Also correct the initial
sampling rate for Mic 1.
Update the module description.
Signed-off-by: Ian Minett <ian_minett@creativelabs.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the controls used for tuning the DSP effects.
Signed-off-by: Ian Minett <ian_minett@creativelabs.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the unsolicited response handler for incoming DSP responses and
jack detection reporting, and routines for reading the incoming DSP response.
Signed-off-by: Ian Minett <ian_minett@creativelabs.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove the playback PCM open callback.
PCM stream setup and cleanup functions are added for use by PCM callbacks.
Delay stream cleanup if effects are on, to allow time for any effects tail to
finish.
Add the analog capture PCM callbacks.
Change the max channels of analog playback to 6.
Add two new PCMs: AMic2 and What-U-Hear.
Signed-off-by: Ian Minett <ian_minett@creativelabs.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the kcontrols for the DSP effects, playback and recording
source selection.
ca0132_is_vnode_effective() checks whether virtual node settings have
taken effect.
The control change helpers ca0132_pe_switch_set(), ca0132_voicefx_set()
and ca0132_cvoice_switch_set() are added to toggle playback / capture
DSP effects, ca0132_voicefx_info(), _get() and _put() are added for
input path DSP effect value access. The volume helpers are updated to
volume_info(), _get() and _set() to use the virtual nodes.
The redundant headphone and speaker switches and ct_extension function
are removed.
Signed-off-by: Ian Minett <ian_minett@creativelabs.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the framework to set effect parameters: ca0132_effects_set()
and ca0132_setup_defaults() are general functions for parameter setting and
initializing to default values. dspio_set_param() and dspio_set_uint_param()
are lower-level fns to simplify setting individual DSP parameters via an
SCP buffer transfer to the firmware.
The CA0132 chip parameter init code is added in ca0132_init_params().
In chipio_[write,read]_data(), the current chip address is auto-incremented
if no error has occurred.
ca0132_select_out() selects the current output. If autodetect is enabled,
use headphones (if jack detected) or speakers (if no jack).
ca0132_select_mic() selects the current mic in. If autodetect is enabled,
use exterior mic (if jack detected) or built-in mic (if no jack).
Init digital mic and switch between dmic and amic with ca0132_init_dmic(),
ca0132_set_dmic(). amic2 is initialized in ca0132_init_analog_mic2().
Finally, add verb tables for configuring DSP firmware.
Signed-off-by: Ian Minett <ian_minett@creativelabs.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds definitions and structs used for configuring DSP effects,
virtual nodes, effect tuning controls, and mixer control helpers.
The effect structs are also initialized.
Signed-off-by: Ian Minett <ian_minett@creativelabs.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tidy up and condense chipio_write_address|addx() functions.
Improve dspio_write_wait() to use jiffies for timeout calc.
Signed-off-by: Ian Minett <ian_minett@creativelabs.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add comments and descriptions to functions.
Bump dsp_free_ports() to below dsp_allocate_ports_format() to group the
alloc functions together for commenting.
Signed-off-by: Ian Minett <ian_minett@creativelabs.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the code needed to fetch the DSP binary image from the local
firmware install location and transfer it over to the chip using the new DSP
loader bus ops.
Actual DSP effect controls, parameters and mixers are to be included later.
- Add calls to new DSP loader system to transfer firmware to the hardware.
- Add chip read/write routines, DSP I/O, SCP packet format helper functions and
transfer DMA management.
- Add guard around DSP download to ensure loader config switch is enabled.
The general scheme for downloading the DSP is as follows:
1) If DSP firmware loader is enabled, ca0132_download_dsp() is called
to start the process.
2) Driver requests DSP image using request_firmware().
3) Driver sets up the streaming DMA for DSP image download
with dspload_image() and dspxfr_image(), which in turn calls the DSP loader
op snd_hda_codec_load_dsp_prepare() to ready the system.
4) DSP image will consist of 1 or more segments, each transferred in sequence
by a call to dspxfr_one_seg() and snd_hda_codec_load_dsp_trigger().
5) Once complete, the loader state is cleaned up with
snd_hda_codec_load_dsp_cleanup().
Signed-off-by: Ian Minett <ian_minett@creativelabs.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It's possible that these amps are settable somehow, e g through
secret codec verbs, but for now, don't create the controls (as
they won't be working anyway, and cause errors in amixer).
Cc: stable@kernel.org
BugLink: https://bugs.launchpad.net/bugs/1038651
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CA0132 driver had some codes to handle the S/PDIF I/O, but the actual
setups of pins and converters were missing. Now the pins are added.
Also, fixed a few points triggering invalid codec verbs and mixer
elements since the digital I/O audio widgets on CA0132 have no amp.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now with the workaround using codec->pcm_format_first flag, we can
clean up the home-baked codes in patch_ca0132.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
