On AR9300 the rx FIFO needs to be empty during reset to ensure that no
further DMA activity is generated, otherwise it might lead to memory
corruption issues.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SKBs that are allocated in the HTC layer do not have callbacks
registered and hence ended up not being freed, Fix this by freeing
them properly in the TX completion routine.
Cc: <stable@vger.kernel.org>
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adds the spectral scan feature for ath9k. AR92xx and AR93xx chips
are supported for now. The spectral scan is triggered by configuring
a mode through a debugfs control file. Samples can be gathered via
another relay debugfs file.
Essentially, to try it out:
echo chanscan > /sys/kernel/debug/ieee80211/phy0/ath9k/spectral_scan_ctl
iw dev wlan0 scan
cat /sys/kernel/debug/ieee80211/phy0/ath9k/spectral_scan0 > samples
echo disable > /sys/kernel/debug/ieee80211/phy0/ath9k/spectral_scan_ctl
This feature is still experimental.
The special "chanscan" mode is used to perform spectral scan while
mac80211 is scanning for channels. To allow this,
sw_scan_start/complete() ops have been added.
The patch contains code snippets and information from Zefir Kurtisi and
information provided by Adrian Chadd and Felix Fietkau.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For AR9550, program the synth value based on the ref. clock.
The logic for AR9550 is similar to AR9330, but keep the code
separate since changes for AR9330 are required - which would be
done later.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When AGC calibration is to be done, a GPM message with the
payload, MCI_GPM_WLAN_CAL_REQ has to be sent. Currently this falls
within the IQ-CAL code block which is incorrect. Fix this by using
a separate variable to decide when IQ-CAL is to be done separately
and call ar9003_mci_init_cal_req correctly.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IQ calibration doesn't complete and times out for half/quarter
rates, so skip it correctly.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TX_IQ_ON_AGC_CAL should not be enabled for AR9340. TX-IQ calibration
is run as part of AGC calibration only for AR9485, AR9462 and AR9565.
For the others (AR9300, AR9330, AR9340), TX-IQ cal is done independent
of AGC-cal.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is not enabled for any chip and is unused.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Doing this in ath9k_hw_fill_cap_info() is odd and it's
cleaner to do this in the init function for calibration.
Also, setup the supported calibration type in init_cal_settings.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some 3-column initval arrays have wrong comments. The
column of these arrays is indexed by the 'freqIndex'
variable in 'ar5008_hw_process_ini' which only depends
on the actual band.
The 'initvals' tool from 'qca-swiss-army-knife' prints
the correct comment lines for these arrays, since commit
'atheros-initvals: fix comments for non-fastclock 3-column tables'
however the comments were not refreshed in ath9k.
The patch contains no functional changes.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ath9k consists of 2 different sub-modules: ATH9K and ATH9K_HTC.
Both uses common Atheros code from ath.ko and need ATH_COMMON.
However, while ATH9K selects ATH_COMMON, ATH9K_HTC does not.
As result, if ATH9K_HTC is the only Atheros card selected, compilation fails with
unresolved symbols.
This patch moves ATH_COMMON selection to the common part for both
ATH9K and ATH9K_HTC
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When TX aggregation is stopped, there are a few
different cases:
- connection with the peer was dropped
- session stop was requested locally
- session stop was requested by the peer
- connection was dropped while a session is stopping
The behaviour in these cases should be different, if
the connection is dropped then the driver should drop
all frames, otherwise the frames may continue to be
transmitted, aggregated in the case of a locally
requested session stop or unaggregated in the case of
the peer requesting session stop.
Split these different cases so that the driver can
act accordingly; however, treat local and remote stop
the same way and ask the driver to not send frames as
aggregated packets any more.
In the case of connection drop, the stop callback the
driver is otherwise supposed to call is no longer
required.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Populate iniModesRxGain with the correct initvals
array for AR9485 v1.1
Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since ath9k makes use of mac80211's debugfs hooks to
maintain station statistics, make ATH9K_DEBUGFS
select MAC80211_DEBUGFS. This fixes the issue reported by
Fengguang Wu:
drivers/net/wireless/ath/ath9k/debug.c: In function 'ath9k_sta_add_debugfs':
drivers/net/wireless/ath/ath9k/debug.c:1589:4: error: 'struct ath_node' has no member named 'node_stat'
drivers/net/wireless/ath/ath9k/debug.c: In function 'ath9k_sta_remove_debugfs':
drivers/net/wireless/ath/ath9k/debug.c:1599:19: error: 'struct ath_node' has no member named 'node_stat'
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Host bridge hotplug:
- Untangle _PRT from struct pci_bus (Bjorn Helgaas)
- Request _OSC control before scanning root bus (Taku Izumi)
- Assign resources when adding host bridge (Yinghai Lu)
- Remove root bus when removing host bridge (Yinghai Lu)
- Remove _PRT during hot remove (Yinghai Lu)
SRIOV
- Add sysfs knobs to control numVFs (Don Dutile)
Power management
- Notify devices when power resource turned on (Huang Ying)
Bug fixes
- Work around broken _SEG on HP xw9300 (Bjorn Helgaas)
- Keep runtime PM enabled for unbound PCI devices (Huang Ying)
- Fix Optimus dual-GPU runtime D3 suspend issue (Dave Airlie)
- Fix xen frontend shutdown issue (David Vrabel)
- Work around PLX PCI 9050 BAR alignment erratum (Ian Abbott)
Miscellaneous
- Add GPL license for drivers/pci/ioapic (Andrew Cooks)
- Add standard PCI-X, PCIe ASPM register #defines (Bjorn Helgaas)
- NumaChip remote PCI support (Daniel Blueman)
- Fix PCIe Link Capabilities Supported Link Speed definition (Jingoo Han)
- Convert dev_printk() to dev_info(), etc (Joe Perches)
- Add support for non PCI BAR ROM data (Matthew Garrett)
- Add x86 support for host bridge translation offset (Mike Yoknis)
- Report success only when every driver supports AER (Vijay Pandarathil)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iQIcBAABAgAGBQJQyKwSAAoJEPGMOI97Hn6zScgQAJZK2VDfCv74mKrgSDNokIzH
5nVDrc9AHKJm7CUODs6keJK5d4TD/za3Zao68zrYHsJJKes2ni2Z3W34HP2RXKK2
eOmePXOHYPPZMlimP9r9cVxNu1ZJCyp/yWSBcsPF4zUgWhBWLRaSj85I049gQ0sz
+05nZYfLjVd3HNiaXsG4CQyMrNF46XEsLhF9vs+Nr2GHPwrpzhfScgYv63oDS86C
3ICKsjmiRUZcNelxIFYmyxa5u89QdW5XHjzc9eHGQuus24Vxw+TZzsdfc17sUJEE
HTyXY+RjDpOVhdtwwUjrCEOiyZYvy3g9+3sKxoxgt/76ghdUaR7fxITwB97qVMFD
T0ESlKjSV/Qv5QYdyy5uP4zwNs/PXCWXkTg/L1m71F30BxKWDa7tgiA6uK7Z7fl5
1aokKBdk3mtJJJIDJG1YkxPXx/JItTGCNYrx7CcFj49rSjrUWLQdmrYahersRIsB
3wiD2xTi9e4dXeP/+VGzGOWB/sHk+73jvrvZe/REa1FCnMINDz4+9V9WaGROMqyq
MQ8kX0KfYcNVNxy1GOXjU5wLpMN/t/QbvI7gwzRP1DAUCJPoOgFy7AjvSTVG3zuy
8CtdOFttVkUn5dqsbQR0gVbyQVTS3PGSKz5XC/s8kVDWhja0xZTBYwrskM/4zdSD
Xf48OyYV5EjpC3FYUSiU
=OE3Q
-----END PGP SIGNATURE-----
Merge tag 'for-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI update from Bjorn Helgaas:
"Host bridge hotplug:
- Untangle _PRT from struct pci_bus (Bjorn Helgaas)
- Request _OSC control before scanning root bus (Taku Izumi)
- Assign resources when adding host bridge (Yinghai Lu)
- Remove root bus when removing host bridge (Yinghai Lu)
- Remove _PRT during hot remove (Yinghai Lu)
SRIOV
- Add sysfs knobs to control numVFs (Don Dutile)
Power management
- Notify devices when power resource turned on (Huang Ying)
Bug fixes
- Work around broken _SEG on HP xw9300 (Bjorn Helgaas)
- Keep runtime PM enabled for unbound PCI devices (Huang Ying)
- Fix Optimus dual-GPU runtime D3 suspend issue (Dave Airlie)
- Fix xen frontend shutdown issue (David Vrabel)
- Work around PLX PCI 9050 BAR alignment erratum (Ian Abbott)
Miscellaneous
- Add GPL license for drivers/pci/ioapic (Andrew Cooks)
- Add standard PCI-X, PCIe ASPM register #defines (Bjorn Helgaas)
- NumaChip remote PCI support (Daniel Blueman)
- Fix PCIe Link Capabilities Supported Link Speed definition (Jingoo
Han)
- Convert dev_printk() to dev_info(), etc (Joe Perches)
- Add support for non PCI BAR ROM data (Matthew Garrett)
- Add x86 support for host bridge translation offset (Mike Yoknis)
- Report success only when every driver supports AER (Vijay
Pandarathil)"
Fix up trivial conflicts.
* tag 'for-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (48 commits)
PCI: Use phys_addr_t for physical ROM address
x86/PCI: Add NumaChip remote PCI support
ath9k: Use standard #defines for PCIe Capability ASPM fields
iwlwifi: Use standard #defines for PCIe Capability ASPM fields
iwlwifi: collapse wrapper for pcie_capability_read_word()
iwlegacy: Use standard #defines for PCIe Capability ASPM fields
iwlegacy: collapse wrapper for pcie_capability_read_word()
cxgb3: Use standard #defines for PCIe Capability ASPM fields
PCI: Add standard PCIe Capability Link ASPM field names
PCI/portdrv: Use PCI Express Capability accessors
PCI: Use standard PCIe Capability Link register field names
x86: Use PCI setup data
PCI: Add support for non-BAR ROMs
PCI: Add pcibios_add_device
EFI: Stash ROMs if they're not in the PCI BAR
PCI: Add and use standard PCI-X Capability register names
PCI/PM: Keep runtime PM enabled for unbound PCI devices
xen-pcifront: Handle backend CLOSED without CLOSING
PCI: SRIOV control and status via sysfs (documentation)
PCI/AER: Report success only when every device has AER-aware driver
...
Due to my recent commit (ath9k: allow to load EEPROM
content via firmware API) smatch complains about that
the 'pdata' variable in 'ath9k_hw_init' can be NULL
and it is dereferenced before checking that. That is
absolutely correct.
Check the 'pdata' variable before using it to avoid
a NULL pointer dereference.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Accurate RX timestamp reporting is important for proper IBSS merging,
mesh synchronization, and MCCA scheduling. Namely, knowing where the TSF
is recorded is needed to sync with the beacon timestamp field.
Tested with AR9271.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Accurate RX timestamp reporting is important for proper IBSS merging,
mesh synchronization, and MCCA scheduling. Namely, knowing where the TSF
is recorded is needed to sync with the beacon timestamp field.
Tested with AR9280.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The calibration data for devices w/o a separate
EEPROM chip can be specified via the 'eeprom_data'
field of 'ath9k_platform_data'. The 'eeprom_data'
is usually filled from board specific setup
functions. It is easy if the EEPROM data is mapped
to the memory, but it can be complicated if it is
stored elsewhere.
The patch adds support for loading of the EEPROM
data via the firmware API to avoid this limitation.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 'ath9k_hw_nvram_read' function takes a
'struct ath_common *' as its first argument.
Almost each of its caller has a 'struct ath_hw *'
parameter in their argument list, and that is
dereferenced in order to get the 'struct ath_common'
pointer.
Change the first argument of 'ath9k_hw_nvram_read'
to be a 'struct ath_hw *', and remove the dereference
calls from the callers.
Also change the type of the first argument of the
ar9300_eeprom_read_{byte,word} functions.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Show the EEPROM offset of the failed read operation
in 'ath9k_hw_nvram_read'. The debug message is more
informative this way.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The fill_eeprom functions are printing the same
debug message in case the 'ath9k_hw_nvram_read'
function fails. Remove the duplicated code from
fill_eeprom functions and add the ath_dbg call
directly into 'ath9k_hw_nvram_read'.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While AR_PHY_CCA_NOM_VAL_* does contain the expected internal noise floor
for a chip measured in clean air, it refers to the lowest expected reading.
Depending on the frequency, this measurement can vary by about 6db, thus
causing a higher reported channel noise and signal strength.
Factor in the 6db offset when converting internal noisefloor to channel noise.
This patch makes the reported values more accurate for all chips without
affecting NF calibration behavior.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Assign the training power for PAPRD based on the chip.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a HW capability to indicate whether PAPRD is enabled
for the card, since PAPRD could be enabled in the EEPROM, but
disabled in the driver. This makes things clearer.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Retraining of PAPRD based on agc2_pwr is required for
chips other than AR9485.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Remove unneeded memset.
All the values in the PAPRD gain table are filled, so there
is no need to zero out the arrays.
* Use GFP_KERNEL in ar9003_paprd_create_curve
This is called from the PAPRD work, so the atomic variant
is not needed.
* Change return type of ar9003_paprd_setup_gain_table
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the PowerSave wrappers outside ath_paprd_activate(),
since they are already being used in ath_paprd_calibrate().
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The PAPRD training control registers have to be
programmed with values that depend on the chip. This patch
ensures that the correct values are chosen for the chip
in use.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Various PAPRD registers are at addresses that are different
from those for the rest of the chips in the AR9003 family.
Fix them.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit "ath9k: Fix the 'xmit' debugfs file" changed the
the array size of ath_stats.txstats to IEEE80211_NUM_ACS,
which is wrong because the HW queue number is used to
update the statistics. Revert back to using ATH9K_NUM_TX_QUEUES.
Reported-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit f74b9d365d.
Turns out reverting commit a240dc7b3c
"ath9k_hw: Updated AR9003 tx gain table for 5GHz" was not enough to
bring the tx power back to normal levels on devices like the
Buffalo WZR-HP-G450H, this one needs to be reverted as well.
This revert improves tx power by ~10 db on that device
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Cc: rmanohar@qca.qualcomm.com
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the standard #defines for PCIe Capability ASPM fields.
Previously we used PCIE_LINK_STATE_L0S and PCIE_LINK_STATE_L1 directly, but
these are defined for the Linux ASPM interfaces, e.g.,
pci_disable_link_state(), and only coincidentally match the actual register
bits. PCIE_LINK_STATE_CLKPM, also part of that interface, does not match
the register bit.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
ath9k does not provide any runtime pm callbacks, so support for
PM_RUNTIME is not needed and we could go to PM_SLEEP.
This also makes it possible to use SIMPLE_DEV_PM_OPS instead of
manually filling struct dev_pm_ops.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are 2 different things:
- sub-menu for "Atheros Wireless cards" family
- module ath.ko with common Atheros code
Until now, they both used to depend on the same Kconfig variable ATH_COMMON.
Thus, being "Atheros card" and "depending on ath.ko" was the same.
To allow module to belong to the
"Atheros Wireless cards" family but not use ath.ko,
2 conditions above need to be separated.
So, this patch introduce new Kconfig variable ATH_CARDS for belonging
to the "Atheros Wireless Cards" family; while ATH_COMMON becomes hidden
variable to express dependency on common Atheros code in ath.ko. Modules
that depend on this common code now express it by setting ATH_COMMON.
Right now, ath6kl do not depend on common code and thus do not set ATH_COMMON.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
'bf_next' is cleared using ATH_TXBUF_RESET() in both the
callsites of ath_tx_get_buffer().
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ethtool statistics are available only when
CONFIG_ATH9K_DEBUGFS is enabled, move these functions
to debug.c
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: stomp audio profiles on weak signal
strength" failed to take care of new stomp type while
programming concurrent tx priority. That leads to array
index out of bounds access.
drivers/net/wireless/ath/ath9k/btcoex.c:414
ath9k_hw_btcoex_set_concur_txprio()
error: buffer overflow 'stomp_txprio' 4 <= 4
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 'stations' debugfs file has multiple issues. It doesn't scale
to an arbitrary number of associated stations and allocating
64K is not elegant either. Now that changes have been made in
mac80211 to support dynamic creation/deletion of driver-specific
debugfs files on station addition/removal, remove this file and
make use of the mac80211 hooks (which will be done in a sebsequent
patch).
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update the rate statistics only when debugfs has been enabled
in ath9k and mac80211 and move the stat() functions under proper
conditionals.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the rate control statistics debugfs file properly
via remove_sta_debugfs(). Also, check for both MAC80211_DEBUGFS
and ATH9K_DEBUGFS config options.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 'xmit' debugfs file has become big and unwieldy, fix
multiple issues with its usage:
* Store TX counters/statistics only for the 4 Access Categories.
Use IEEE80211_NUM_ACS instead of ATH9K_NUM_TX_QUEUES.
* Move various utility macros to debug.h, they can be reused
elsewhere.
* Remove tx_complete_poll_work_seen.
* Remove code that accesses various internal queue-specific
variables without any locking whatsoever. HW/SW queue details
will be handled in a subsequent patch.
* Do not print internal values like txq_headidx and txq_headidx.
They were mostly unused anyway, considering code like:
PRX("txq_tailidx: ", txq_headidx);
* Handle 'txprocdesc' for EDMA too.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the macros provided by mac80211 and remove redundant
declarations inside the drivers.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On lower WLAN signal strength, WLAN downlink traffic might suffer
from retransmissions. At the mean time, playing SCO/A2DP profiles
is affecting WLAN stability. In such scenario, by stomping SCO/A2DP
BT traffic completely for a BTCOEX period, gives WLAN traffic an
oppertunity to recover PHY rate. It also improves WLAN stability at
lower RSSI without sacificing BT traffic.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch reverts the commit "ath9k_hw: Wait BT calibration to complete"
and bail out from MCI interrupt routine for chip reset. The above commit
stalls the WLAN TCP traffic while bringing up and down the BT interface
iteratively. Fixing this properly by queueing up chip reset and bailing
out properly from tasklet routine.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
FATAL and WATCHDOG interrupts should be processed first followed
by others.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The debugfs file for dumping btcoex parameters unconditionally
assumes a MCI-based device. This will not work for older btcoex
chips. Fix this by branching out the routine into separate
functions.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit "ath9k: improve suspend/resume reliability" broke ath9k_htc
and bringing up the device would hang indefinitely. Fix this.
Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2484 Mhz (Japan) usage requires filter coefficients to
be programmed in the CCK TX FIR registers. This is required
for AR9331, AR9485 and AR9462. Fix this and also remove
a few useless macros and a duplicate variable.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The workaround for ASPM/L0s is needed only for AR9485 1.0,
which was never sold and is not supported by ath9k.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
An issue is reported in AR9462 & AR9565 that NF_cal_not_done is
not observed when HW peak detector calibration is disabled. At that
state, the HW is stuck at NF calibration which prevents tx output.
The root cause is wrong peak detector offset calibrated by HW. To
resolve this issue, peak detector calibration is done manually by SW
for AR9462 and AR9565.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add 5% width tolerance for radar patterns defined by ETSI.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Free instance of pattern detector if requested DFS domain is
not supported.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
set_domain() is already defined in /arch/arm/asm/domain.h
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow drivers to indicate their mactime is at RX completion and adjust
for this in mac80211. Also rename the existing RX_FLAG_MACTIME_MPDU to
RX_FLAG_MACTIME_START to clarify its intent. Based on similar code by
Johannes Berg.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
[fix docs, atheros drivers]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During hardware restart, all interfaces are iterated even
though they haven't been re-added to the driver, document
this behaviour. The same also happens during resume, which
is even more confusing since all of the interfaces were
previously removed from the driver. Make this optional so
drivers relying on the current behaviour can still use it,
but to let drivers that don't want this behaviour disable
it.
Also convert all API users, keeping the old semantics
except in hwsim, where the new normal ones are desired.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The ath9k xmit functions for AMPDUs can send frames as non-aggregate in case
only one frame is currently available. The client will then answer using a
normal Ack instead of a BlockAck. This acknowledgement has no TID stored and
therefore the hardware is not able to provide us the corresponding TID.
The TID set by the hardware in the tx status descriptor has to be seen as
undefined and not as a valid TID value for normal acknowledgements. Doing
otherwise results in a massive amount of retransmissions and stalls of
connections.
Users may experience low bandwidth and complete connection stalls in
environments with transfers using multiple TIDs.
This regression was introduced in b11b160def
("ath9k: validate the TID in the tx status information").
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Cc: stable@vger.kernel.org
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whenever WLAN receives scheduling msg from BT, it reduces tx power
based on RSSI level. And then BT starts simultaneous transmission
along with WLAN. Sometimes HW MAC compares tx power that is used
prior to power reduction which is causing BT transmission to defer.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reduced the power consumption to half in full and network sleep.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reduced the power consumption to half in full and network sleep.
Cc: stable@vger.kernel.org
Cc: Paul Stewart <pstew@chromium.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the BT connection is initiated by headset, it's possible that headset
requests to make one A2DP and one Voice connection over the same link.
BT firmware will send a new profile A2DP_Voice in this case. So WLAN
has to take care of this new profile for tuning BTCOEX parameters.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whenever i_coff of IQ calibration is too high, AR9565 drops max
rx rate to MCS4. Skipping IQ update at this time can avoid this
problem for AR9565.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While resuming from S3, BT host issues HCI reset command and it
causes BT firmware to busy with security key calculation. At this
movement, WLAN detects MCI hardware error of MCI_CONT_INFO_TIMEOUT
and then it starts the recovery sequence repeatedly. Too many
recovery sequences would exhaust the BT kernel message pool. This
patch imposes a duration between consecutive BT recovery procedure.
Thus it solves BT firmware panic issue reported in AR9565.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TXIQ and RXIQ share the same data path to upload the measurement
result, we should turn off RXIQ calibration while re-calibrating radio
Signed-off-by: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Self generated MCI messages is configured to use chain 1. As
ar9565 is 1x1 solution, It can not use Chain 1. Hence fix
Chain 1 for ar9462 alone. Not doing so, could affect WLAN
connectivity in ar9565 as LNA sharing is not informed by BT.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The simulataneous transmission of both WLAN and BT might cause
increase in power levels. To avoid regulatory violation, WLAN tx
power will be adjusted according to BT power index based on avaliability
of BT scheduling messages. WLAN tx power reduction might affect its
performance. So WLAN tx power is only be lowered when the signal strength
is good enough. Otherwise concurrent tx will be disabled and WLAN uses
it default power levels. Also concurrent tx is disabled whenever WLAN is
moving to off-channel which might be used by BT.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is useful to have channel mode in caldata to find out
whether operaing channel is in HT40/20 when we are currently
on offchannel. It will be used by BTCOEX to enable/disable
concurrent tx mechanism later.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This feature enables both WLAN and BT can transmit simultaneously
by setting WLAN and BT to equal priorities. Whenever both are
transmitting, it might violate regulatory power limits. To avoid
regulatory violation, WLAN tx power will be adjusted according to BT
power index based on avaliability of BT scheduling message. If the
combined power exceeds threshold, BT transmission will be held off.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WLAN updates channel bitmap when associated and disassociated. Channel
bitmap will reflect whare are the channels used or affected by WLAN and
BT should avoid using those. Not doing so, could affect BT traffic
as both WLAN and BT is operating on same channel.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently ath9k need to have beacon interval matched
between STA mode and beaconing mode. Advertize this
through interface combinations.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Once the driver advertizes interface combination logic
based on its firmware/hardware limitation, cfg80211
takes care of all the necessary logic such as maximum
beaconing vifs, standlone interface etc.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will allow us to create virtual interface the driver supports.
Also this ensures multivif support and limitation advertised
by the driver is taken care in cfg80211 itself.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When WLAN is idle ensure we downgrade to FTP_STOMP_LOW weight
(from STOMP_LOW) to provide more bandwidth for BT FTP profile.
WLAN's idleness can be estimated by taking into account of the
rx data packets and just ignore beacons, qos nullfunc etc.
Also update bt_wait_time even if the chip is in NETWORK SLEEP
mode. This should help BT throughput when WLAN is idle.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
bf->bf_next is only while buffers are chained as part of an A-MPDU
in the tx queue. When a tid queue is flushed (e.g. on tearing down
an aggregation session), frames can be enqueued again as normal
transmission, without bf_next being cleared. This can lead to the
old pointer being dereferenced again later.
This patch might fix crashes and "Failed to stop TX DMA!" messages.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
