Debugfs files reg_addr and reg_val are used for reading and writing to the
firmware (target) registers. reg_addr contains the address to be accessed,
which also needs to be set first, and reg_value is when used for reading and
writing the actual value in ASCII.
To read a value from the firmware register 0x100000:
# echo 0x100000 > reg_addr
# cat reg_value
0x00100000:0x000002d3
To write value 0x2400 to address 0x100000:
# echo 0x100000 > reg_addr
# echo 0x2400 > reg_value
#
Signed-off-by: Yanbo Li <yanbol@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k_tx_wep_key_work() acquires conf_mutex, so
cancelling it when conf_mutex is already taken
in ath10k_remove_interface() is incorrect, so
move it outside the lock.
Snippet from the lockdep report:
kernel: ======================================================
kernel: [ INFO: possible circular locking dependency detected ]
kernel: 3.18.0-rc5-wl-debug #34 Tainted: G O
kernel: -------------------------------------------------------
kernel: hostapd/451 is trying to acquire lock:
kernel: ((&arvif->wep_key_work)){+.+...}, at: [<ffffffff810872d5>] flush_work+0x5/0x290
kernel: but task is already holding lock:
kernel: (&ar->conf_mutex){+.+.+.}, at: [<ffffffffa0b99f00>] ath10k_remove_interface+0x40/0x290 [ath10k_core]
kernel: which lock already depends on the new lock.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
peer->keys needs to be protected by data_lock
since it is also accessed from the WMI path.
Both install() and clear() routines for peer
keys modify the key contents, so use the data_lock
to avoid races.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When static keys are used in shared WEP, when a
station is associated, message 3 is sent with an
encrypted payload. But, for subsequent
authentications that are triggered without a
deauth, the auth frame is decrypted by the HW.
To handle this, check if the WEP keys have already
been set for the peer and if so, mark the
frame as decrypted. This scenario can happen
when a station changes its default TX key and initiates
a new authentication sequence.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some firmware revisions don't seem to deilver
management frames with FCS error via WMI so narrow
down the HTT rule to not drop corrupted management
frames.
This basically increases number of frames ath10k
reports while sniffing.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When mac80211 requests driver to cancel a hw roc
the driver must not call the expired() callback or
else roc will fail in some cases depending on how
things get scheduled.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With P2P concurrency requested hw roc duration
time can be very small. Some firmware revisions
refuse scan requests with too small channel dwell
time.
This prevents messages like, e.g. with connected
STA vif and performing P2P Find:
ath10k_pci 0000:00:05.0: failed to switch to channel for roc scan
ieee80211 phy3: failed to start next HW ROC (-110)
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New firmware revisions don't need peer creation
when doing offchannel tx. Earlier revisions would
queue and never release frames without a peer.
This prevent new firmware revisions from stopping
replenishing wmi-htc tx credits and improves
reliability of offchannel tx which would sometimes
silently fail.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Return value of irq_of_parse_and_map() is unsigned int, with 0
indicating failure, so testing for negative result never works.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Kevin Cernekee <cernekee@gmail.com>
Link: https://lkml.kernel.org/r/20141114221642.GA37468@dtor-ws
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Comment was out-of-date. The headroom is no longer
necessary because HTT Tx fragment list is stored
in dma pool item associated with each sk_buff.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Return value of irq_of_parse_and_map() is unsigned int, with 0
indicating failure, so testing for negative result never works.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Kevin Cernekee <cernekee@gmail.com>
Link: https://lkml.kernel.org/r/20141114221614.GA37395@dtor-ws
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When re-associating a station, the nss was set back to
maximum value even if user had configured small number
of tx chains. So, pay attention to user's config in
this case as well.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It appears it takes more than just setting the
hardware's chainmask to make things work well. Without
this patch, a vdev would only use 1x1 rates when chainmask
was set to 0x3.
Setting the 'nss' (number of spatial streams) on the vdev
helps the firmware's rate-control algorithm work properly.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The Armada 375 SoC comes with an USB2 host and device controller and
an USB3 controller. The USB cluster control register allows to manage
common features of both USB controllers.
This commit adds a driver integrated in the generic PHY framework to
control this USB cluster feature.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
[ kishon@ti.com : Made it to use the updated devm_phy_create API and
soem cosmentic changes in Kconfig file.]
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Armada 375 comes with an USB2 host and device controller and an USB3
controller. The USB cluster control register allows to manage common
features of both USB controllers. This commit adds the Device Tree
binding documentation for this piece of hardware.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Describe the binding for the Marvell MVEBU SATA phy. This driver
can be used at least with Kirkwood, Dove and maybe others.
Additionally, update the SATA binding with the properties to link
to the phy nodes.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: coccinelle/api/ptr_ret.cocci
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
There are currently 2 differents naming conventions used between the
existing Armada SoC DT files for pinctrl entries (*_pin(s): *-pin(s)
and pmx_*: pmx-*) with a vast majority of files using the former:
$ grep _pin arch/arm/boot/dts/armada-*.dts* | wc -l
155
$ grep pmx arch/arm/boot/dts/armada-*.dts* | wc -l
13
In fact, only some Armada XP files are using the second variant.
This patch normalizes those files (mainly ge0/1 entries) to use
the first variant.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/00114c3169e1d93259ff4150ed46ee36eae16b1e.1416670812.git.arno@natisbad.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
While renaming pinctrl entries during reviews of Synology DS414 support
series, I missed three entries, as reported by Ben. This patch fixes
those.
Reported-by: Ben Peddell <klightspeed@killerwolves.net>
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/608e4fd6e06e9c5289a84b9c38e81b2456dbcd79.1416670812.git.arno@natisbad.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
On Armada 375, the USB cluster allows to control the cluster composed
of the USB2 and USB3 host controllers.
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/1415879269-29711-6-git-send-email-gregory.clement@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
PHY driver and its associated Device Tree node(s)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WOgc
-----END PGP SIGNATURE-----
Merge tag 'tags/phy-dt-header' into mvebu/dt-usb_phy
shared header file which will be referenced from both
PHY driver and its associated Device Tree node(s)
Pull nfsd bugfixes from Bruce Fields:
"These fix one mishandling of the case when security labels are
configured out, and two races in the 4.1 backchannel code"
* 'for-3.18' of git://linux-nfs.org/~bfields/linux:
nfsd: Fix slot wake up race in the nfsv4.1 callback code
SUNRPC: Fix locking around callback channel reply receive
nfsd: correctly define v4.2 support attributes
It may be useful info, e.g. if someone wants to use ubinize.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Pull aio fix from Ben LaHaise:
"Dirty page accounting fix for aio"
* git://git.kvack.org/~bcrl/aio-fixes:
aio: fix uncorrent dirty pages accouting when truncating AIO ring buffer
Pull powerpc fixes from Ben Herrenschmidt:
"This series fix a nasty issue with radeon adapters on powerpc servers,
it's all CC'ed stable and has the relevant maintainers ack's/reviews.
Basically, some (radeon) adapters have issues with MSI addresses above
1T (only support 40-bits). We had powerpc specific quirk but it only
listed a specific revision of an adapter that we shipped with our
machines and didn't properly handle the audio function which some
distros enable nowadays.
So we made the quirk generic and fixed both the graphic and audio
drivers properly to use it.
Without that, ppc64 server machines will crash at boot with a radeon
adapter.
Note: This has been brewing for a while, it just needed a last respin
which got delayed due to us moving ozlabs to a new location in town
and other such things taking priority"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/pci: Remove unused force_32bit_msi quirk
powerpc/pseries: Honor the generic "no_64bit_msi" flag
powerpc/powernv: Honor the generic "no_64bit_msi" flag
sound/radeon: Move 64-bit MSI quirk from arch to driver
gpu/radeon: Set flag to indicate broken 64-bit MSI
PCI/MSI: Add device flag indicating that 64-bit MSIs don't work
ALSA: hda - Limit 40bit DMA for AMD HDMI controllers
If an inode has converted inline_data which was written to the disk, we should
set its inode flag for further fsync so that this inline_data can be recovered
from sudden power off.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
The commit "genirq: Generic chip: Change irq_reg_{readl,writel}
arguments" modified the API. In the same tome the
arch/arm/plat-orion/gpio.c file received a fix with the use of the old
API: "ARM: orion: Fix for certain sequence of request_irq can cause
irq storm". This commit fixes the use of the API.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Olof Johansson <olof@lixom.net>
Link: https://lkml.kernel.org/r/1416928752-24529-1-git-send-email-gregory.clement@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
single fix in one of the basic clock templates. No fixes to the core
this time around. As with most clock driver fixes these run the gamut
from fixing a build warning to fixing wrecked memory timings, with a
little USB tossed in for fun. Please consider pulling.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJUcrkwAAoJEDqPOy9afJhJzq4P/jT9K+g0ljQrY93t97Wm6s4x
Xi+RrVO/MOUhpIGzqrhPflGALl5Yj96iBUiC2QSVpVjDUdoQL5tc8c3FtQDGA7fA
Q/9e2yUmjQ+nNxizdeIzaNUHO+fIe8FEn3NwyondfaDlI1sqVv/0WAf6MNkuLCwM
/DJ1MmJbwgK255gI3FwUhbNylCCPeUENKRs3xGW3p4+fFIZGyROhBsJClE1nUiT1
EFzWM6Bq29qOLxZ4Dqkfzz1BWLiqcTlRcf8ZaHjME77k09ybwNS9cmXrB9gHhmlL
sMfDa0uwsv/mFWRohP5jK3AUqqtR7EgcPL5euO+d9Q+nBVofgTwxyvA0nlGqX8XQ
hm1OZeolnWHPPHasRkgzSnd/0b/A8s+tr96XSvHjIlrx1ioWQD2K7GU82/3bObTL
isqzW34+Y0dX2GpgwJu2eWrSwHk705wBA0t8/pP+r7aWdUsyX4J1ElGHLElzTLI0
VkQZPwKvjVNd0kQRplZ/KPQoboDuFh8b09+MvG8Kz8t3Ilt0MS7rFrxEQ6xIBfe9
M49vUJw2egmOCgcWp3GeyICIQJCfet2acyZy+vJivpu0//ssD7BT/woR7qmgHic1
kmiVdj1iBSoUK4NIr+DvsNmMMDEW58CSK/j11chitT8WCRGYKW849iUk7LiGhXU0
IgTphTfMdFF1a2gzqaQo
=4O2k
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of https://git.linaro.org/people/mike.turquette/linux
Pull clock fixes from Mike Turquette:
"The fixes for the clock framework are all regressions in drivers, plus
a single fix in one of the basic clock templates. No fixes to the
core this time around.
As with most clock driver fixes these run the gamut from fixing a
build warning to fixing wrecked memory timings, with a little USB
tossed in for fun"
* tag 'clk-fixes-for-linus' of https://git.linaro.org/people/mike.turquette/linux:
clk: pxa: fix pxa27x CCCR bit usage
clk-divider: Fix READ_ONLY when divider > 1
clk: qcom: Fix duplicate rbcpr clock name
clk: at91: usb: fix at91sam9x5 recalc, round and set rate
clk: at91: usb: fix at91rm9200 round and set rate
After flushing dirty nat entries, it has to be no more dirty nat
entries.
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
It's meaningless to check dirty_nat_cnt after re-dirtying nat entries in
journal. And although there are rooms for dirty nat entires if dirty_nat_cnt
is zero, it's also meaningless to check __has_cursum_space.
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Option journal_async_commit breaks gurantees of data=ordered mode as it
sends only a single cache flush after writing a transaction commit
block. Thus even though the transaction including the commit block is
fully stored on persistent storage, file data may still linger in drives
caches and will be lost on power failure. Since all checksums match on
journal recovery, we replay the transaction thus possibly exposing stale
user data.
To fix this data exposure issue, remove the possibility to use
journal_async_commit in data=ordered mode.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
This adds suspend/resume support for the of-serial driver
to provide power management support on devices attatched.
The handling may vary since not every of_serial device is
an 8250 port. Currently only 8250 port handling is added
in the suspend/resume function based on the type switch.
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Joseph Lo <josephl@nvidia.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Florina Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 2dea53bf57.
Turns out to be broken :(
Cc: Jingchang Lu <jingchang.lu@freescale.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 513e438581.
It's broken :(
Cc: Jingchang Lu <jingchang.lu@freescale.com>
Cc: Joseph Lo <josephl@nvidia.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Attempting to use SysRq via the 8250 serial port with spin lock
debugging on on a uniprocessor system results in the following splat:
SysRq :
BUG: spinlock trylock failure on UP on CPU#0, swapper/0
lock: serial8250_ports+0x0/0x8c0, .magic: dead4ead, .owner: swapper/0, .owner_cpu: 0
CPU: 0 PID: 0 Comm: swapper Not tainted 3.18.0-rc4+ #37
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140531_083030-gandalf 04/01/2014
ffffffff8245ba00 ffffffff81628b28 ffffffff812c8d27 ffffffff81628b48
ffffffff8106812e ffffffff8245ba00 ffffffff814e22ed ffffffff81628b68
ffffffff810681a6 0000000000000000 0000000000000000 ffffffff81628b88
Call Trace:
<IRQ> [<ffffffff812c8d27>] dump_stack+0x19/0x1b
[<ffffffff8106812e>] spin_dump+0x7e/0xd0
[<ffffffff810681a6>] spin_bug+0x26/0x30
[<ffffffff8106843c>] do_raw_spin_trylock+0x4c/0x60
[<ffffffff812cdb1d>] _raw_spin_trylock+0x1d/0x60
[<ffffffff812336d8>] serial8250_console_write+0x68/0x190
[<ffffffff811eb0b0>] ? sprintf+0x40/0x50
[<ffffffff8106ab5e>] call_console_drivers.constprop.11+0x9e/0xf0
[<ffffffff8106b276>] console_unlock+0x3e6/0x490
[<ffffffff8106b595>] vprintk_emit+0x275/0x530
[<ffffffff812c869a>] printk+0x4d/0x4f
[<ffffffff8121e612>] __handle_sysrq+0x62/0x1b0
[<ffffffff8121e5b5>] ? __handle_sysrq+0x5/0x1b0
[<ffffffff8121ebc6>] handle_sysrq+0x26/0x30
[<ffffffff81233157>] serial8250_rx_chars+0x1d7/0x250
[<ffffffff812338bb>] serial8250_handle_irq+0x7b/0x90
[<ffffffff812338f3>] serial8250_default_handle_irq+0x23/0x30
[<ffffffff812318b3>] serial8250_interrupt+0x63/0xe0
[<ffffffff8106d80e>] handle_irq_event_percpu+0x4e/0x200
[<ffffffff8106da01>] handle_irq_event+0x41/0x70
[<ffffffff810701ee>] ? handle_edge_irq+0x1e/0x110
[<ffffffff8107026e>] handle_edge_irq+0x9e/0x110
[<ffffffff810041c2>] handle_irq+0x22/0x40
[<ffffffff812d096e>] do_IRQ+0x4e/0xf0
[<ffffffff812cf4ed>] common_interrupt+0x6d/0x6d
<EOI> [<ffffffff8100acbf>] ? default_idle+0x1f/0xd0
[<ffffffff8100acbd>] ? default_idle+0x1d/0xd0
[<ffffffff8100b61f>] arch_cpu_idle+0xf/0x20
[<ffffffff8105c1db>] cpu_startup_entry+0x25b/0x360
[<ffffffff812c726e>] rest_init+0xbe/0xd0
[<ffffffff816a4dcb>] start_kernel+0x339/0x346
[<ffffffff816a4495>] x86_64_start_reservations+0x2a/0x2c
[<ffffffff816a4589>] x86_64_start_kernel+0xf2/0xf6
HELP : loglevel(0-9) reboot(b) crash(c) show-all-locks(d) te...
Before ebade5e833 ("serial: 8250: Clean up the locking for -rt")
this was handled by not even attempting to try the lock if port->sysrq,
since it is known to be taken by the interrupt handler; see
https://bugzilla.kernel.org/show_bug.cgi?id=6716#c1. Restore that
behavior.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since most drivers interpret UPIO_MEM32 to mean "little-endian" and use
readl/writel to access the registers, add a parallel UPIO_MEM32BE to
request the use of big-endian MMIO accessors (ioread32be/iowrite32be).
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hardcoded FIFO size can cause hardware performance limitation.
Using real size value provides better FIFO usage.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we have fifosize set in driver data we prefer to use it instead of default
fifosize value (which is always 16). If there is defined fifosize for particular
serial we prefer to use it, otherwise we use value from info, which is
common for all serials on given platform.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds waiting until transmit buffer and shifter will be empty
before clock disabling.
Without this fix it's possible to have clock disabled while data was
not transmited yet, which causes unproper state of TX line and problems
in following data transfers.
Cc: <stable@vger.kernel.org> # v2.6.26+
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tty break and error flags are not bit masks so do not to use bitwise
OR when assigning them.
Note that there is no functional change due to the if-else construct and
flag having been initialised to zero (TTY_NORMAL).
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
