This reverts commit d4d25deca4.
It tried to fix long standing bugzilla entries, but the solution was
reported to break other systems. The reporter of
http://bugzilla.kernel.org/show_bug.cgi?id=9791
tracked it down to this commit and confirmed that reverting the patch
restores the correct behaviour. It's too late in the release cycle to
find a better solution than reverting the commit to avoid regressions.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Fix following Section mismatch warning in sparc64:
WARNING: arch/sparc64/kernel/built-in.o(.text+0x13dec): Section mismatch: reference to .devinit.text:pci_scan_one_pbm (between 'psycho_scan_bus' and 'psycho_pbm_init')
WARNING: arch/sparc64/kernel/built-in.o(.text+0x14b58): Section mismatch: reference to .devinit.text:pci_scan_one_pbm (between 'sabre_scan_bus' and 'sabre_init')
WARNING: arch/sparc64/kernel/built-in.o(.text+0x15ea4): Section mismatch: reference to .devinit.text:pci_scan_one_pbm (between 'schizo_scan_bus' and 'schizo_pbm_init')
WARNING: arch/sparc64/kernel/built-in.o(.text+0x17780): Section mismatch: reference to .devinit.text:pci_scan_one_pbm (between 'pci_sun4v_scan_bus' and 'pci_sun4v_get_head')
WARNING: arch/sparc64/kernel/built-in.o(.text+0x17d5c): Section mismatch: reference to .devinit.text:pci_scan_one_pbm (between 'pci_fire_scan_bus' and 'pci_fire_get_head')
WARNING: arch/sparc64/kernel/built-in.o(.text+0x23860): Section mismatch: reference to .devinit.text:vio_dev_release (between 'vio_create_one' and 'vio_add')
WARNING: arch/sparc64/kernel/built-in.o(.text+0x23868): Section mismatch: reference to .devinit.text:vio_dev_release (between 'vio_create_one' and 'vio_add')
The pci_* were all missing __init annotations.
For the vio.c case it was a function with a wrong annotation which was removed.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
tc35815: Use irq number for tc35815-mac platform device id
[MIPS] Malta: Fix reading the PCI clock frequency on big-endian
[MIPS] SMTC: Fix build error.
The tc35815-mac platform device used a pci bus number and a devfn to
identify its target device, but the pci bus number may vary if some
bus-bridges are found. Use irq number which is be unique for embedded
controllers.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The JMPRS register on Malta boards keeps a 32-bit CPU-endian
value. The readw() function assumes that the value it reads is a
little-endian 16-bit number. Therefore, using readw() to obtain
the value of the JMPRS register is a mistake. This error leads
to incorrect reading of the PCI clock frequency on big-endian
during board start-up.
Change readw() to __raw_readl().
This was tested by injecting a call to printk() and verifying
that the value of the jmpr variable was consistent with current
setting of the JP4 "PCI CLK" jumper.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'omap-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
ARM: OMAP1: Fix compile for board-nokia770
ARM: OMAP1: Keymap fix for f-sample and p2-sample
'select' used by config symbol 'INTEL_IOATDMA' refers to undefined symbol 'DCA'
Although drivers/dma is currently the only user future drivers outside of
drivers/dma may select this option so it is better to add this to
arch/arm/Kconfig than move DCA to drivers/dma/Kconfig.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
r2 is not guaranteed to be preserved over a function call, so relying
on it to store the link register over the call to sleep_phys_sp() is
unreliable. Store the link register on the stack instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The i386 and x86_64 arch directories contain nothing but a generated symlink
to arch/x86/boot/bzImage when a tree a built.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Anvin <hpa@zytor.com>
Signed-off-by: Josef 'Jeff' Sipek <jeffpc@josefsipek.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The latest Intel processors (the 45nm ones) have a model number of 23
(old ones had 15); they're otherwise compatible on the oprofile side.
This patch adds the new model number to the oprofile code.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The trap handler does properly update the fraction,
but not the exponent...
Thanks to Paolo Bonzini for the bug report and the testcase.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Paolo Bonzini <bonzini@gnu.org>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Move alignment to page size of init data outside ifdef for BLK_DEV_INITRD.
The reservation up to page size of memory after init data was previously
not done if BLK_DEV_INITRD was undefined.
This caused a kernel oops when init memory pages were freed after startup,
data placed in the same page as the last init memory would also be freed
and reused, with disastrous results.
- Use macros for initcalls and .text sections.
- Replace hardcoded page size constant with PAGE_SIZE define.
- Change include/asm-cris/page.h to use the _AC macro to instead
of testing __ASSEMBLY__.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1) Trap level wasn't being passed down properly, we need to
move it from %l4 into the correct outgoing arg register.
2) Although the TPC often provides the most direct clue, we
have the caller PC so we should provide that as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
The compiler team did the hard work for this distilling a problem in
large fortran application which showed up when applied to a 290MB input
data set down to this instruction:
ldfd f34=[r17],-8
Which they noticed incremented r17 by 0x10 rather than decrementing it
by 8 when the value in r17 caused an unaligned data fault. I tracked
it down to some bad instruction decoding in unaligned.c. The code
assumes that the 'x' bit can determine whether the instruction is
an "ldf" or "ldfp" ... which it is for opcode=6 (see table 4-29 on
page 3:302 of the SDM). But for opcode=7 the 'x' bit is irrelevent,
all variants are "ldf" instructions (see table 4-36 on page 3:306).
Note also that interpreting the instruction as "ldfp" means that the
"paired" floating point register (f35 in the example here) will also
be corrupted.
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch restores the blackfin Hardware Performance Monitor Profiling
support that was killed by the combining of instrumentation menus in
commit 09cadedbdc.
Since there seems to be no good reason to behave differently from other
architectures, it now automatically selects the hardware performance
counters whenever the profiling is activated.
mach-common/irqpanic.c: pm_overflow calls pm_overflow_handler which is
in oprofile/op_model_bf533.c. I doubt that setting HARDWARE_PM as "m"
will work at all, since the pm_overflow_handler should be in the core
kernel image because it is called by irqpanic.c.
Therefore, I change HARDWARE_PM from a tristate to a bool.
The whole arch/$(ARCH)/oprofile/ is built depending on CONFIG_OPROFILE. Since
part of the HARDWARE_PM support files sits in this directory, it makes sense to
also depend on OPROFILE, not only PROFILING. Since OPROFILE already depends on
PROFILING, it is correct to only depend on OPROFILE only.
Thanks to Adrian Bunk for finding this bug and providing an initial
patch.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
CC: Adrian Bunk <adrian.bunk@movial.fi>
CC: Randy Dunlap <randy.dunlap@oracle.com>
CC: bryan.wu@analog.com
Acked-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 09cadedbdc ("Combine
instrumentation menus in kernel/Kconfig.instrumentation") broke ARM
profiling support, since ARM has some extra Kconfig options and doesn't
just use the common OPROFILE/KPROBES config options.
Rather than just revert the thing outright, or add ARM-specific
knowledge to the generic Kconfig.instrumentation file (where the only
and whole point was to be generic, not too architecture-specific), this
just makes ARM not use the generic version, since it doesn't suit it.
So create an arm-specific version of Kconfig.instrumentation instead,
and use that.
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Russell King <rmk+lkml@arm.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the current code, RTC_AIE doesn't work if the RTC relies on
CONFIG_HPET_EMULATE_RTC because the code sets the RTC_AIE flag in
hpet_set_rtc_irq_bit(). The interrupt handles does accidentally check
for RTC_PIE and not RTC_AIE when comparing the time which was set in
hpet_set_alarm_time().
I now verified on a test system here that without the patch applied,
the attached test program fails on a system that has HPET with
2.6.24-rc7-default. That's not critical since I guess the problem has
been there for several kernel releases, but as the fix is quite
obvious.
Configuration is CONFIG_RTC=y and CONFIG_HPET_EMULATE_RTC=y.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Denys Fedoryshchenko reported a bootup crash when he upgraded
his system from 3GB to 4GB RAM:
http://lkml.org/lkml/2008/1/7/9
the bug is due to HIGHMEM4G && SPARSEMEM kernels making pfn_to_page()
to return an invalid pointer when the pfn is in a memory hole. The
256 MB PCI aperture at the end of RAM was not mapped by sparsemem,
and hence the pfn was not valid. But set_highmem_pages_init() iterated
this range without checking the pfn's validity first.
this bug was probably present in the sparsemem code ever since sparsemem
has been introduced in v2.6.13. It was masked due to HIGHMEM64G using
larger memory regions in sparsemem_32.h:
#ifdef CONFIG_X86_PAE
#define SECTION_SIZE_BITS 30
#define MAX_PHYSADDR_BITS 36
#define MAX_PHYSMEM_BITS 36
#else
#define SECTION_SIZE_BITS 26
#define MAX_PHYSADDR_BITS 32
#define MAX_PHYSMEM_BITS 32
#endif
which creates 1GB sparsemem regions instead of 64MB sparsemem regions.
So in practice we only ever created true sparsemem holes on x86 with
HIGHMEM4G - but that was rarely used by distros.
( btw., we could probably save 2MB of mem_map[]s on X86_PAE if we reduced
the sparsemem region size to 256 MB. )
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Commit 473980a993 added a call to clear
the SLB shadow buffer before registering it. Unfortunately this means
that we clear out the entries that slb_initialize has previously set in
there. On POWER6, the hypervisor uses the SLB shadow buffer when doing
partition switches, and that means that after the next partition switch,
each non-boot CPU has no SLB entries to map the kernel text and data,
which causes it to crash.
This fixes it by reverting most of 473980a9 and instead clearing the
3rd entry explicitly in slb_initialize. This fixes the problem that
473980a9 was trying to solve, but without breaking POWER6.
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Cacheops.h: Fix typo.
[MIPS] Cobalt: Qube1 has no serial port so don't use it
[MIPS] Cobalt: Fix ethernet interrupts for RaQ1
[MIPS] Kconfig fixes for BCM47XX platform
Commit 5d2efba64b changed our iommu code
so that it always uses an iommu page size of 4kB. That means with our
current code, drivers may do a dma_map_sg() of a 64kB page and obtain
a dma_addr_t that is only 4k aligned.
This works fine in most cases except for some infiniband HW it seems,
where they tell the HW about the page size and it ignores the low bits
of the DMA address.
This works around it by making our IOMMU code enforce a PAGE_SIZE alignment
for mappings of objects that are page aligned in the first place and whose
size is larger or equal to a page.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Because Qube1 doesn't have a serial chip waiting for transmit fifo empty
takes forever, which isn't a good idea. No prom_putchar/early console
for Qube1 fixes this.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Acked-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
RAQ1 uses the same interrupt routing as Qube2.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The patch below fixes two problems for Kconfig on the BCM47xx platform:
- arch/mips/bcm47xx/gpio.c uses ssb_extif_* functions. Selecting
SSB_DRIVER_EXTIF makes sure those functions are available.
- arch/mips/pci/pci.c needs, when enabled, platform specific functions,
which are defined when SSB_PCICORE_HOSTMODE is enabled.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This fixes compilation error where i2c_init wasn't defined.
Also, remove the CVS log and version tags, they are no longer useful.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes compile error when nr_free_pages() from linux/swap.h
expands to global_page_state(NR_FREE_PAGES), but linux/vmstat.h isn't
included to declare global_page_state().
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes a kernel panic on boot due to do_signal not being compatible
with it's callers.
- do_signal now returns void, and does not have the previous signal set
as a parameter.
- Remove sys_rt_sigsuspend, we can use the common one instead.
- Change sys_sigsuspend to be more like x86, don't call do_signal here.
- handle_signal, setup_frame and setup_rt_frame now return -EFAULT
if we've delivered a segfault, which is used by callers to perform
necessary cleanup.
- Break long lines, correct whitespace and formatting errors.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sometimes cpu_idle_wait gets stuck because it might miss CPUS that are
already in idle, have no tasks waiting to run and have no interrupts going
to them. This is common on bootup when switching cpu idle governors.
This patch gives those CPUS that don't check in an IPI kick.
Background:
-----------
I notice this while developing the mcount patches, that every once in a
while the system would hang. Looking deeper, the hang was always at boot
up when registering init_menu of the cpu_idle menu governor. Talking
with Thomas Gliexner, we discovered that one of the CPUS had no timer
events scheduled for it and it was in idle (running with NO_HZ). So the
CPU would not set the cpu_idle_state bit.
Hitting sysrq-t a few times would eventually route the interrupt to the
stuck CPU and the system would continue.
Note, I would have used the PDA isidle but that is set after the
cpu_idle_state bit is cleared, and would leave a window open where we
may miss being kicked.
hmm, looking closer at this, we still have a small race window between
clearing the cpu_idle_state and disabling interrupts (hence the RFC).
CPU0: CPU 1:
--------- ---------
cpu_idle_wait(): cpu_idle():
| __cpu_cpu_var(is_idle) = 1;
| if (__get_cpu_var(cpu_idle_state)) /* == 0 */
per_cpu(cpu_idle_state, 1) = 1; |
if (per_cpu(is_idle, 1)) /* == 1 */ |
smp_call_function(1) |
| receives ipi and runs do_nothing.
wait on map == empty idle();
/* waits forever */
So really we need interrupts off for most of this then. One might think
that we could simply clear the cpu_idle_state from do_nothing, but I'm
assuming that cpu_idle governors can be removed, and this might cause a
race that a governor might be used after the module was removed.
Venki said:
I think your RFC patch is the right solution here. As I see it, there is
no race with your RFC patch. As long as you call a dummy smp_call_function
on all CPUs, we should be OK. We can get rid of cpu_idle_state and the
current wait forever logic altogether with dummy smp_call_function. And so
there wont be any wait forever scenario.
The whole point of cpu_idle_wait() is to make all CPUs come out of idle
loop atleast once. The caller will use cpu_idle_wait something like this.
// Want to change idle handler
- Switch global idle handler to always present default_idle
- call cpu_idle_wait so that all cpus come out of idle for an instant
and stop using old idle pointer and start using default idle
- Change the idle handler to a new handler
- optional cpu_idle_wait if you want all cpus to start using the new
handler immediately.
Maybe the below 1s patch is safe bet for .24. But for .25, I would say we
just replace all complicated logic by simple dummy smp_call_function and
remove cpu_idle_state altogether.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <ak@suse.de>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is almost no difference between 32 & 64 bit glue code.
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Fix CPU hotplug when using the SLB shadow buffer
[POWERPC] efika: add phy-handle property for fec_mpc52xx
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
pnpacpi: print resource shortage message only once
PM: ACPI and APM must not be enabled at the same time
ACPI: apply quirk_ich6_lpc_acpi to more ICH8 and ICH9
ACPICA: fix acpi_serialize hang regression
ACPI : Not register gsi for PCI IDE controller in legacy mode
ACPI: Reintroduce run time configurable max_cstate for !CPU_IDLE case
ACPI: Make sysfs interface in ACPI power optional.
ACPI: EC: Enable boot EC before bus_scan
increase PNP_MAX_PORT to 40 from 24
When we switched away from the optimized C version
things stopped being monotonic.
The problem is that if we run this with interrupts disabled, we can
see the interrupt pending because the counter reached the limit value.
When this happens the counter has bit 31 set, and the low bits start
counting again from zero.
Reported by Martin Habets.
Signed-off-by: David S. Miller <davem@davemloft.net>
ACPI and APM used "pm_active" to guarantee that
they would not be simultaneously active.
But pm_active was recently moved under CONFIG_PM_LEGACY,
so that without CONFIG_PM_LEGACY, pm_active became a NOP --
allowing ACPI and APM to both be simultaneously enabled.
This caused unpredictable results, including boot hangs.
Further, the code under CONFIG_PM_LEGACY is scheduled
for removal.
So replace pm_active with pm_flags.
pm_flags depends only on CONFIG_PM,
which is present for both CONFIG_APM and CONFIG_ACPI.
http://bugzilla.kernel.org/show_bug.cgi?id=9194
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
I noticed that the commit f197465384
(MIPS Tech: Get rid of volatile in core code) broke the software
reset functionality for MIPS Malta boards in big-endian mode.
According to the MIPS Malta board user's manual, writing the magic
32-bit GORESET value into the SOFTRES register initiates board soft
reset. My experimentation has shown that the endianness of the GORESET
integer should thereby be the same as the endianness, which has been
set for the CPU itself. The writew() function used to write the magic
value in the code introduced by the commit mentioned above, however,
swaps bytes for big-endian kernels and transfers 16 bits instead of 32.
The patch below replaces the writew() function by the __raw_writel()
routine, which leaves the byte order intact and transfers the whole
MIPS machine word. Trivial code cleanup (replacing spaces by a tab
and cutting oversized lines to make checkpatch.pl happy) is also
included.
The patch was tested using a Malta evaluation board running in both
BE and LE modes. For both modes, software reset was fully functional
after the change.
P.S. I suspect that the same commit broke the "standby" functionality
for MIPS Atlas boards. However, I did not touch the Atlas code as I
don't have such board at my disposal and also because the linux-mips.org
Web site claims that Atlas support is scheduled for removal.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch converts PNX8XXX system timer to clocksource restoring PNX8550
support back to live.
Signed-off-by: Vitaly Wool <vitalywool@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Before we register the SLB shadow buffer, we need to invalidate the
entries in the buffer, otherwise we can end up stale entries from when
we previously offlined the CPU.
This does this invalidate as well as unregistering the buffer with
PHYP before we offline the cpu. Tested and fixes crashes seen on
970MP (thanks to tonyb) and POWER5.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is the x86-64 version of the Salsa20 stream cipher algorithm. The
original assembly code came from
<http://cr.yp.to/snuffle/salsa20/amd64-3/salsa20.s>. It has been
reformatted for clarity.
Signed-off-by: Tan Swee Heng <thesweeheng@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch contains the salsa20-i586 implementation. The original
assembly code came from
<http://cr.yp.to/snuffle/salsa20/x86-pm/salsa20.s>. I have reformatted
it (added indents) so that it matches the other algorithms in
arch/x86/crypto.
Signed-off-by: Tan Swee Heng <thesweeheng@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
crypto_blkcipher_decrypt is wrong because it does not care about
the IV.
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Some CPUs support only 128 bit keys in HW. This patch adds SW fallback
support for the other keys which may be required. The generic algorithm
(and the block mode) must be availble in case of a fallback.
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
32 bit and 64 bit glue code is using (now) the same
piece code. This patch unifies them.
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The setkey() function can be shared with the generic algorithm.
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The setkey() function can be shared with the generic algorithm.
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This three defines are used in all AES related hardware.
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
These two instructions exceptionally take a single precision register
as their operand. This means we can't use vfp_get_dm() to read the
register number - we need to use vfp_get_sm() instead. Add a flag to
indicate this exception to the general rule.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The new network driver fec_mpc52xx will not work on efika because the
firmware does not provide all required properties.
http://www.powerdeveloper.org/asset/by-id/46 has a Forth script to
create more properties. But only the phy stuff is required to get a
working network.
This should go into the kernel because its appearently
impossible to boot the script via tftp and then load the real boot
binary (yaboot or zimage).
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With CPU_HOTPLUG=n:
WARNING: vmlinux.o(.text+0x104f8): Section mismatch: reference to .init.text:fork_idle (between
'do_fork_idle' and 'lapic_timer_broadcast')
do_fork_idle() needs to be __cpuinit. It can be static as well.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Fix CONFIG_BOOT_RAW.
[MIPS] Assume R4000/R4400 newer than 3.0 don't have the mfc0 count bug
[MIPS] Fix IP32 breakage
[MIPS] Alchemy: Fix use of __init code bug exposed by modpost warning
[MIPS] Move inclusing of kernel/time/Kconfig menu to appropriate place
This seems as reasonable assumption and gets some SNI machines to work
which currently must rely on the cp0 counter as clocksource.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- suppress master aborts during config read
- set io_map_base
- only fixup end of iomem resource to avoid failing request_resource
in serial driver
- killed useless setting of crime_int bit, which caused wrong interrupts
- use physcial address for serial port platform device and let 8250
driver do the ioremap
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
WARNING: vmlinux.o(.text+0x1ca608): Section mismatch: reference to
.init.text: add_wired_entry (between 'config_access' and 'config_read')
by refactoring the code calling add_wired_entry() from config_access() to
a separate function which is called from aau1x_pci_setup(). While at it:
- make some unnecassarily global variables 'static';
- fix the letter case, whitespace, etc. in the comments...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CONFIG_NO_HZ, CONFIG_HIGH_RES_TIMERS should be selected in "Kernel
type" menu, not in "CPU selection" menu.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- Add missing i2c_board_info struct for at91rm9200
Signed-off-by: Jan Altenberg <jan.altenberg@linutronix.de>
Acked-by: Andrew Victor <avictor.za@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Montecito and Montvale behaves slightly differently than previous
Itanium processors, resulting in the MCA due to a failed PIO read
to sometimes surfacing outside the nofault code. This code is
based on discussions with Intel CPU architects and verified at
customer sites.
Signed-off-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Suspend/resume on the pxa25x was fairly obviously broken in revision
711be5ccfe.
This patch fixes the damage by adding back the missing code.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit aed3a8c9bb introduced a
definition of notify_spus_active in .../cell/spu_syscalls.c, and
another definition under #ifndef MODULE in .../cell/spufs/sched.c.
The latter is not necessary and causes the build to fail when
CONFIG_SPU_FS=y, so this removes it. It also removes the export
of do_notify_spus_active, which is unnecessary.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
After 17d57a9206 ("x86: fix x86-32 early
fixmap initialization.") removing lg.ko caused a printk from vunmap:
mm/memory.c:115: bad pgd 004b3027.
On the second use after module load, the kernel crashes.
This fixes the immediate problem (accessed and dirty bits not set as
expected in pmd_none_or_clear_bad). I can't see why this would cause
a crash, but I haven't been able to reproduce it once this is applied.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a bug in the printing of the os-area magic numbers which assumed
that magic numbers were zero terminated strings. The magic numbers
are represented in memory as integers. If the os-area sections are
not initialized correctly they could contained random data that would
be printed to the display. Also unify the handling of header and db
magic numbers and make both of type array of u8.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This removes an OProfile dependency on the spufs module. This
dependency was causing a problem for multiplatform systems that are
built with support for Oprofile on Cell but try to load the oprofile
module on a non-Cell system.
Signed-off-by: Bob Nelson <rrnelson@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This reverts commit fbdcf18df7.
As pointed out by Yanmin Zhang, the problem was already fixed
differently (and correctly), and rather than fix anything, it actually
causes us to create a sub-optimal sched-domains hierarchy (not setting
up the domain belonging to the core) when CONFIG_X86_HT=y.
Requested-by: Yanmin Zhang <yanmin_zhang@linux.intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds a cpu cache info entry for the Intel Tolapai cpu.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Andrew "Eagle Eye" Morton noticed that we use raw_local_save_flags()
instead of raw_local_irq_save(flags) in die(). This allows the
preemption of oopsing contexts - which is highly undesirable. It also
causes CONFIG_DEBUG_PREEMPT to complain, as reported by Miles Lane.
this bug was introduced via:
commit 39743c9ef7
Author: Andi Kleen <ak@suse.de>
Date: Fri Oct 19 20:35:03 2007 +0200
x86: use raw locks during oopses
- spin_lock_irqsave(&die.lock, flags);
+ __raw_spin_lock(&die.lock);
+ raw_local_save_flags(flags);
that is not a correct open-coding of spin_lock_irqsave(): both the
ordering is wrong (irqs should be disabled _first_), and the wrong
flags-saving API was used.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
when called by setup_arch) after smp_store_cpu_info() had set it to the
correct value.
The error shows up in 'cat /proc/cpuinfo' will all cpus = 0.
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Suresh B Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Adjust CMCI mask on CPU hotplug
[IA64] make flush_tlb_kernel_range() an inline function
[IA64] Guard elfcorehdr_addr with #if CONFIG_PROC_FS
[IA64] Fix Altix BTE error return status
[IA64] Remove assembler warnings on head.S
[IA64] Remove compiler warinings about uninitialized variable in irq_ia64.c
[IA64] set_thread_area fails in IA32 chroot
[IA64] print kernel release in OOPS to make kerneloops.org happy
[IA64] Two trivial spelling fixes
[IA64] Avoid unnecessary TLB flushes when allocating memory
[IA64] ia32 nopage
[IA64] signal: remove redundant code in setup_sigcontext()
IA64: Slim down __clear_bit_unlock
Currently CMCI mask of hot-added CPU is always disabled after CPU hotplug.
We should adjust this mask depending on CMC polling state.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This fixes an unused variable warning in mm/vmalloc.c.
Tony: also fix resulting fallout in uncached.c with a
typo in args to flush_tlb_kernel_range().
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Access to elfcorehdr_addr needs to be guarded by #if CONFIG_PROC_FS
as well as the existing #if guards.
Fixes the following build problem:
arch/ia64/hp/common/built-in.o: In function
`sba_init':arch/ia64/hp/common/sba_iommu.c:2043: undefined reference to `elfcorehdr_addr'
:arch/ia64/hp/common/sba_iommu.c:2043: undefined reference to `elfcorehdr_addr'
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The Altix shub2 BTE error detail bits are in a different location
than on shub1. The current code does not take this into account
resulting in all shub2 BTE failures mapping to "unknown".
This patch reads the error detail bits from the proper location,
so the correct BTE failure reason is returned for both shub1
and shub2.
Signed-off-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch removes the following assembler warning messages.
AS arch/ia64/kernel/head.o
arch/ia64/kernel/head.S: Assembler messages:
arch/ia64/kernel/head.S:1179: Warning: Use of 'ld8' violates RAW dependency 'CR[PTA]' (data)
arch/ia64/kernel/head.S:1179: Warning: Only the first path encountering the conflict is reported
arch/ia64/kernel/head.S:1178: Warning: This is the location of the conflicting usage
arch/ia64/kernel/head.S:1180: Warning: Use of 'ld8' violates RAW dependency 'CR[PTA]' (data)
arch/ia64/kernel/head.S:1180: Warning: Only the first path encountering the conflict is reported
arch/ia64/kernel/head.S:1178: Warning: This is the location of the conflicting usage
:
arch/ia64/kernel/head.S:1213: Warning: Use of 'ldf.fill.nta' violates RAW dependency 'CR[PTA]' (data)
arch/ia64/kernel/head.S:1213: Warning: Only the first path encountering the conflict is reported
arch/ia64/kernel/head.S:1178: Warning: This is the location of the conflicting usage
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch removes the following compiler warning messages.
CC arch/ia64/kernel/irq_ia64.o
arch/ia64/kernel/irq_ia64.c: In function 'create_irq':
arch/ia64/kernel/irq_ia64.c:343: warning: 'domain.bits[0u]' may be used uninitialized in this function
arch/ia64/kernel/irq_ia64.c: In function 'assign_irq_vector':
arch/ia64/kernel/irq_ia64.c:203: warning: 'domain.bits[0u]' may be used uninitialized in this function
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
I tried to upgrade an IA32 chroot on my IA64 to a new glibc with TLS.
It kept dying because set_thread_area was returning -ESRCH
(bugs.debian.org/451939).
I instrumented arch/ia64/ia32/sys_ia32.c:get_free_idx() and ended up
seeing output like
[pid] idx desc->a desc->b
-----------------------------
[2710] 0 -> c6b0ffff 40dff31b
[2710] 1 -> 0 0
[2710] 2 -> 0 0
[2710] 0 -> c6b0ffff 40dff31b
[2710] 1 -> c6b0ffff 40dff31b
[2710] 2 -> 0 0
[2711] 0 -> c6b0ffff 40dff31b
[2711] 1 -> c6b0ffff 40dff31b
[2711] 2 -> 48c0ffff 40dff317
which suggested to me that TLS pointers were surviving exec() calls,
leading to GDT pointers filling up and the eventual failure of
get_free_idx().
I think the solution is flushing the tls array on exec.
Signed-Off-By: Ian Wienand <ianw@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The ia64 oops message doesn't include the kernel version, which
makes it hard to automatically categorize oops messages scraped
from mailing lists and bug databases.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Improve performance of memory allocations on ia64 by avoiding a global TLB
purge to purge a single page from the file cache. This happens whenever we
evict a page from the buffer cache to make room for some other allocation.
Test case: Run 'find /usr -type f | xargs cat > /dev/null' in the
background to fill the buffer cache, then run something that uses memory,
e.g. 'gmake -j50 install'. Instrumentation showed that the number of
global TLB purges went from a few millions down to about 170 over a 12
hours run of the above.
The performance impact is particularly noticeable under virtualization,
because a virtual TLB is generally both larger and slower to purge than
a physical one.
Signed-off-by: Christophe de Dinechin <ddd@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
