skb->len is always non-negative.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2038576
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
we were dereferencing dev to initialize pdata. but just after that we
have a BUG_ON(!dev). so we were basically dereferencing the pointer
first and then tesing it for NULL.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The smsc95xx needs to resume with reset operation. Otherwise it causes
system hang by network error like below after resume. This case appears
on odroid u3 board.
[ 9.727600] smsc95xx 1-2:1.0 eth0: kevent 2 may have been dropped
[ 9.727648] smsc95xx 1-2:1.0 eth0: kevent 2 may have been dropped
[ 9.727689] smsc95xx 1-2:1.0 eth0: kevent 2 may have been dropped
[ 9.727728] smsc95xx 1-2:1.0 eth0: kevent 2 may have been dropped
[ 9.729486] PM: resume of devices complete after 2011.219 msecs
[ 10.117609] Restarting tasks ... done.
[ 11.725099] smsc95xx 1-2:1.0 eth0: kevent 2 may have been dropped
[ 13.480846] smsc95xx 1-2:1.0 eth0: kevent 2 may have been dropped
[ 13.481361] smsc95xx 1-2:1.0 eth0: kevent 2 may have been dropped
...
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes a generic hard_header_len check from the usbnet
module that is causing dropped packages under certain circumstances
for devices that send rx packets that cross urb boundaries.
One example is the AX88772B which occasionally send rx packets that
cross urb boundaries where the remaining partial packet is sent with
no hardware header. When the buffer with a partial packet is of less
number of octets than the value of hard_header_len the buffer is
discarded by the usbnet module.
With AX88772B this can be reproduced by using ping with a packet
size between 1965-1976.
The bug has been reported here:
https://bugzilla.kernel.org/show_bug.cgi?id=29082
This patch introduces the following changes:
- Removes the generic hard_header_len check in the rx_complete
function in the usbnet module.
- Introduces a ETH_HLEN check for skbs that are not cloned from
within a rx_fixup callback.
- For safety a hard_header_len check is added to each rx_fixup
callback function that could be affected by this change.
These extra checks could possibly be removed by someone
who has the hardware to test.
- Removes a call to dev_kfree_skb_any() and instead utilizes the
dev->done list to queue skbs for cleanup.
The changes place full responsibility on the rx_fixup callback
functions that clone skbs to only pass valid skbs to the
usbnet_skb_return function.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Reported-by: Igor Gnatenko <i.gnatenko.brain@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
This covers everything under drivers/net except for wireless, which
has been submitted separately.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several files refer to an old address for the Free Software Foundation
in the file header comment. Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.
CC: Oliver Neukum <oliver@neukum.org>
CC: Steve Glendinning <steve.glendinning@shawell.net>
CC: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If suspend callback fails in system sleep context, usb core will
ignore the failure and let system sleep go ahead further, so
this patch doesn't recover device under this situation.
Also add comments on the case.
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The name of FEATURE_AUTOSUSPEND is very misleading and the actual
meaning is remote wakeup, but a device incapable of remote wakeup
still can support USB autosuspend under some situations, so rename
it to avoid misunderstanding.
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b2d4b150(smsc95xx: enable dynamic autosuspend) implements
autosuspend, but breaks current runtime suspend, such as:
when the interface becomes down, the usb device can't be put into
runtime suspend any more.
This patch fixes the broken runtime suspend.
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The three below functions:
smsc95xx_enter_suspend0()
smsc95xx_enter_suspend1()
smsc95xx_enter_suspend2()
return > 0 in case of success, so they will cause smsc95xx_suspend()
to return > 0 and cause suspend failure.
The bug is introduced in commit 3b9f7d(smsc95xx: fix error handling
in suspend failure case).
Cc: <stable@vger.kernel.org> [3.8]
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc failures already get standardized OOM
messages and a dump_stack.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables USB dynamic autosuspend for LAN9500A. This
saves very little power in itself, but it allows power saving
in upstream hubs/hosts.
The earlier devices in this family (LAN9500/9512/9514) do not
support this feature.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register read/write functions already log a warning if
an access fails, so this patch removes the additional warnings
logged by callers that don't add any more information.
This patch makes the resulting driver smaller by not containing
as many warning strings.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a missing endian conversion which results in the
interface failing to come up on BE platforms.
It also removes an unnecessary pointer dereference from this
function.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the ethtool register dump for smsc95xx to dump
all 4 bytes of the final register (COE_CR) instead of just the
first byte.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros, while reducing the amount of code, hide flow control
and make the code more confusing to follow and review. This patch
expands them. It should have no functional effect on the driver.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a bug introduced in bbd9f9e which could prevent
some wakeups from working correctly if multiple wol options were
selected.
This helper function calculates a 16-bit crc and shifts it into
either the high or low 16 bits of a u32 so the caller can or it
directly into place. The function previously had a u16 return
type so would always have returned zero when filter was odd.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Reported-by: Bjorn Mork <bjorn@mork.no>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As pointed out by Bjorn Mork, the generic "usb" driver sets this
for us so no need to directly set it in this driver.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Cc: Bjorn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch ensures that if we fail to suspend the LAN9500 device
we call usbnet_resume before returning failure, instead of
leaving the usbnet driver in an unusable state.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a buffer overflow introduced by bbd9f9e, where
the filter_mask array is accessed beyond its bounds.
Updated to also add a check for kzalloc failure, as reported by
Bjorn Mork and Joe Perches.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Cc: Bjorn Mork <bjorn@mork.no>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid any possible message logging interleaving by adding
missing newlines.
Align arguments.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch splits out the logic for entering suspend modes
to separate functions, to reduce the complexity of the
smsc95xx_suspend function.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables LAN9500 family devices to wake from suspend
on either link up or link down events
It also adds _nopm versions of mdio access functions, so we can
safely call them from suspend and resume functions
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of storing the number of wake-up frame filter registers
in the pdata structure, this patch changes the driver to detect
the type of device we have and store its available features.
The new two features will be used in future patches.
This patch is intended to have no change in behaviour.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
without this patch the two lines below won't ever execute
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device datasheet specifies the BUSY bit must be set when reading
or writing phy registers. This patch ensures we do that.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
Minor conflict between the BCM_CNIC define removal in net-next
and a bug fix added to net. Based upon a conflict resolution
patch posted by Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch applies the introduced usbnet_read_cmd_nopm() and
usbnet_write_cmd_nopm() in the callback of resume and suspend
to avoid deadlock if USB runtime PM is considered into
usbnet_read_cmd() and usbnet_write_cmd().
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes memory leak in smsc95xx_suspend.
Also, it isn't necessary to bother mm to allocate 8bytes/16byte,
and we can use stack variable safely.
Acked-By: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
f7b2927 introduced tx checksum offload support for smsc95xx,
and enabled it by default. This feature doesn't take
endianness into account, so causes most tx to fail on
those platforms.
This patch fixes the problem fully by adding the missing
conversion.
An alternate workaround is to disable TX checksum offload
on those platforms. The cpu impact of this feature is very low.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for wol wakeup on unicast, broadcast,
multicast and arp frames.
The wakeup filter code isn't pretty, but it works.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables wake from system suspend on magic packet.
Patch updated to replace BUG_ON with WARN_ON_ONCE and return.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables the device to enter its lowest power SUSPEND2
state during system suspend, instead of staying up using full power.
Patch updated to not add two pointers to .suspend & .resume.
Patch updated to replace BUG_ON with WARN_ON_ONCE and return.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an issue on some systems, where after suspend the
link is re-established but the ethernet interface does not resume.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds additional checks of the values returned by
smsc95xx_(read|write)_reg, and wraps their common patterns
in macros.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removes unnecessary variables as smsc95xx_write_reg takes its
value by parameter. Early versions passed this parameter by
reference.
Also replace hardcoded interrupt status value with a #define
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
During init, the device reset is unexpected to complete immediately,
so sleep before testing the condition rather than after it.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull trivial tree from Jiri Kosina:
"Trivial updates all over the place as usual."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (29 commits)
Fix typo in include/linux/clk.h .
pci: hotplug: Fix typo in pci
iommu: Fix typo in iommu
video: Fix typo in drivers/video
Documentation: Add newline at end-of-file to files lacking one
arm,unicore32: Remove obsolete "select MISC_DEVICES"
module.c: spelling s/postition/position/g
cpufreq: Fix typo in cpufreq driver
trivial: typo in comment in mksysmap
mach-omap2: Fix typo in debug message and comment
scsi: aha152x: Fix sparse warning and make printing pointer address more portable.
Change email address for Steve Glendinning
Btrfs: fix typo in convert_extent_bit
via: Remove bogus if check
netprio_cgroup.c: fix comment typo
backlight: fix memory leak on obscure error path
Documentation: asus-laptop.txt references an obsolete Kconfig item
Documentation: ManagementStyle: fixed typo
mm/vmscan: cleanup comment error in balance_pgdat
mm: cleanup on the comments of zone_reclaim_stat
...
I no longer have a mailbox at smsc.com, and I've had two reports
that that email address now bounces from people trying to
contact me. This patch updates all references to that invalid
address to one that I can be contacted on more permanently.
This patch also updates the maintainer status to reflect
the fact I'm no longer directly paid to maintain these drivers.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Convert the existing uses of random_ether_addr to
the new eth_random_addr.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"retval" has to be a signed integer for the error handling to work.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inspired by implementation in smsc911x.c and smsc9420.c
Tested on ARM/pandaboard running android
Signed-off-by: Emeric Vigier <emeric.vigier@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hub-initiated LPM is not good for USB communications devices. Comms
devices should be able to tell when their link can go into a lower power
state, because they know when an incoming transmission is finished.
Ideally, these devices would slam their links into a lower power state,
using the device-initiated LPM, after finishing the last packet of their
data transfer.
If we enable the idle timeouts for the parent hubs to enable
hub-initiated LPM, we will get a lot of useless LPM packets on the bus
as the devices reject LPM transitions when they're in the middle of
receiving data. Worse, some devices might blindly accept the
hub-initiated LPM and power down their radios while they're in the
middle of receiving a transmission.
The Intel Windows folks are disabling hub-initiated LPM for all USB
communications devices under a xHCI USB 3.0 host. In order to keep
the Linux behavior as close as possible to Windows, we need to do the
same in Linux.
Set the disable_hub_initiated_lpm flag for for all USB communications
drivers. I know there aren't currently any USB 3.0 devices that
implement these class specifications, but we should be ready if they do.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Hansjoerg Lipp <hjlipp@web.de>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Jan Dumon <j.dumon@option.com>
Cc: Petko Manolov <petkan@users.sourceforge.net>
Cc: Steve Glendinning <steve.glendinning@smsc.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Roland Vossen <rvossen@broadcom.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: "Franky (Zhenhui) Lin" <frankyl@broadcom.com>
Cc: Kan Yan <kanyan@broadcom.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Herton Ronaldo Krzesinski <herton@canonical.com>
Cc: Hin-Tak Leung <htl10@users.sourceforge.net>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Cc: Daniel Drake <dsd@gentoo.org>
Cc: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Without this patch sysfs reports the cable as present
flag@flag-desktop:~$ cat /sys/class/net/eth0/carrier
1
while it's not:
flag@flag-desktop:~$ sudo mii-tool eth0
eth0: no link
Tested on my Beagle XM.
v2: added mantainer to the list of recipient
Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Acked-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make smsc95xx recalculate the hard_mtu after adjusting the
hard_header_len.
Without this, usbnet adjusts the MTU down to 1488 bytes, and the host is
unable to receive standard 1500-byte frames from the device.
Inspired by same fix on cdc_eem 78fb72f793.
Tested on ARM/Beagle.
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace usage of random_ether_addr() with eth_hw_addr_random()
to set addr_assign_type correctly to NET_ADDR_RANDOM.
Change the trivial cases.
v2: adapt to renamed eth_hw_addr_random()
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (73 commits)
arm: fix up some samsung merge sysdev conversion problems
firmware: Fix an oops on reading fw_priv->fw in sysfs loading file
Drivers:hv: Fix a bug in vmbus_driver_unregister()
driver core: remove __must_check from device_create_file
debugfs: add missing #ifdef HAS_IOMEM
arm: time.h: remove device.h #include
driver-core: remove sysdev.h usage.
clockevents: remove sysdev.h
arm: convert sysdev_class to a regular subsystem
arm: leds: convert sysdev_class to a regular subsystem
kobject: remove kset_find_obj_hinted()
m86k: gpio - convert sysdev_class to a regular subsystem
mips: txx9_sram - convert sysdev_class to a regular subsystem
mips: 7segled - convert sysdev_class to a regular subsystem
sh: dma - convert sysdev_class to a regular subsystem
sh: intc - convert sysdev_class to a regular subsystem
power: suspend - convert sysdev_class to a regular subsystem
power: qe_ic - convert sysdev_class to a regular subsystem
power: cmm - convert sysdev_class to a regular subsystem
s390: time - convert sysdev_class to a regular subsystem
...
Fix up conflicts with 'struct sysdev' removal from various platform
drivers that got changed:
- arch/arm/mach-exynos/cpu.c
- arch/arm/mach-exynos/irq-eint.c
- arch/arm/mach-s3c64xx/common.c
- arch/arm/mach-s3c64xx/cpu.c
- arch/arm/mach-s5p64x0/cpu.c
- arch/arm/mach-s5pv210/common.c
- arch/arm/plat-samsung/include/plat/cpu.h
- arch/powerpc/kernel/sysfs.c
and fix up cpu_is_hotpluggable() as per Greg in include/linux/cpu.h
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
(Thanks to Joe Perches for suggesting coccinelle for 0/1 -> true/false).
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
