Update flexcan to support coldfire architecture.
Any new platform should use OF, but coldfire architecture is
actually not supporting devicetrees.
Link: https://lore.kernel.org/r/20210702094841.327679-4-angelo@kernel-space.org
Signed-off-by: Angelo Dureghello <angelo@kernel-space.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add flexcan support for NXP ColdFire mcf5441x family.
This flexcan module is quite similar to imx6 flexcan module, but
with some exceptions:
- 3 separate interrupt sources, MB, BOFF and ERR,
- implements 16 mb only,
- m68k architecture is not supporting devicetrees, so a
platform data check/case has been added,
- ColdFire is m68k, so big-endian cpu, with a little-endian flexcan
module.
Link: https://lore.kernel.org/r/20210702094841.327679-5-angelo@kernel-space.org
Signed-off-by: Angelo Dureghello <angelo@kernel-space.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The es581_tx_can_msg() does below cast:
| tx_can_msg = (struct es581_4_tx_can_msg *)
| &es581_4_urb_cmd->bulk_tx_can_msg.tx_can_msg_buf[msg_len - 1];
The -1 offset is to skip the first member of struct
es581_4_tx_can_msg. However, es581_4_urb_cmd already has a raw_msg
field which can be used instead without the use of an offset
calculation.
The function es58x_fd_tx_can_msg() is also modified to mirror
es581_tx_can_msg().
Link: https://lore.kernel.org/r/20210628155420.1176217-7-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Replace two constant values by a call to sizeof{,_field} on the
relevant field to make the logic easier to understand.
Link: https://lore.kernel.org/r/20210628155420.1176217-6-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Both es58x_probe() and es58x_disconnect() use a similar code snippet
to release the netdev resources. Factorize it in an helper function
named es58x_free_netdevs().
Link: https://lore.kernel.org/r/20210628155420.1176217-5-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Replace kzalloc() with devm_kzalloc(). By doing this, we do not need
to care anymore about having to call kfree(). This result in a
simpler and more easy to read code.
Link: https://lore.kernel.org/r/20210628155420.1176217-4-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Make es58x_init_es58x_dev return a pointer to the allocated structure
instead of returning an integer. Errors are handled through the helper
function ERR_PTR and IS_ERR.
This slightly simplifies the code.
Link: https://lore.kernel.org/r/20210628155420.1176217-3-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Change the author name from "lastname firstname" to "firstname
lastname".
Fix a typo in a variable name in the documentation of struct
es58x_parameters::fifo_mask.
Fix a typo in the title of the datasheet (E701 -> E70) and re-indent
the comments.
Link: https://lore.kernel.org/r/20210628155420.1176217-2-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch updates old code by using the can_change_state() function
published since by the socket-can module.
In particular, this new code better manages the change of bus state by
also using the value of the error counters that the driver now
systematically asks for when initializing the channel.
Link: https://lore.kernel.org/r/20210715142842.35793-1-s.grosjean@peak-system.com
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The CAN - USB PCAN-USB interface is able to generate one-shot frames
as well as loopback frames that it transmits starting from version 4.1
of its firmware.
This patch adds support for the one-shot and loopback functionality to
the driver, that can be activated if the embedded firmware allows it.
If the driver detects that the PCAN-USB device runs an old firmware
(< 4.1) it prints a message suggesting to contact
<support@peak-system.com> for a possible firmware update.
Link: https://lore.kernel.org/r/20210625130931.27438-3-s.grosjean@peak-system.com
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds name and (possibly) firmware version information to
the kernel about the detected PEAK-System CAN - PCI/PCIe interface
card.
Link: https://lore.kernel.org/r/20210607151720.13571-1-s.grosjean@peak-system.com
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
[mkl: reformated struct pci_device_id peak_pci_tbl]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Networking block comments don't use an empty /* line,
use /* Comment...
Block comments use * on subsequent lines.
Block comments use a trailing */ on a separate line.
This patch fixes the comments style issues.
Link: https://lore.kernel.org/r/1624096589-13452-9-git-send-email-huangguangbin2@huawei.com
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch uses the BIT macro for setting individual bits,
to fix the following checkpatch.pl issue:
CHECK: Prefer using the BIT macro.
Link: https://lore.kernel.org/r/1624096589-13452-5-git-send-email-huangguangbin2@huawei.com
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Use DEVICE_ATTR_RW() helper macro instead of plain DEVICE_ATTR(), which
makes the code a bit shorter and easier to read.
Link: https://lore.kernel.org/r/20210603100233.11877-1-thunder.leizhen@huawei.com
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Use DEVICE_ATTR_RO/RW() helper macro instead of plain DEVICE_ATTR(), which
makes the code a bit shorter and easier to read.
Link: https://lore.kernel.org/r/20210603111739.11983-1-thunder.leizhen@huawei.com
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Use DEVICE_ATTR_RO() helper macro instead of plain DEVICE_ATTR(), which
makes the code a bit shorter and easier to read.
Link: https://lore.kernel.org/r/20210603110902.11930-1-thunder.leizhen@huawei.com
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In some configurations, mainly ACPI-based, the clock frequency of the
device is supplied by very well established 'clock-frequency'
property. Hence, try to get it from the property at last if no other
providers are available.
Link: https://lore.kernel.org/r/20210531084444.1785397-1-mkl@pengutronix.de
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Since commit aee2b3ccc8 ("can: tcan4x5x: fix bittiming const, use
common bittiming from m_can driver") there is no use of the device
specific bit timing parameters (m_can_classdev::bit_timing and struct
m_can_classdev::data_timing).
This patch removes the support for custom bit timing from the driver,
as the common bit timing works for all known IP core implementations.
Cc: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
Link: https://lore.kernel.org/r/20210616102811.2449426-7-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Use the devm_platform_ioremap_resource_byname() helper instead of
calling platform_get_resource_byname() and devm_ioremap_resource()
separately.
Link: https://lore.kernel.org/r/20210603073441.2983497-1-yangyingliang@huawei.com
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add support for implementing transceiver node as phy. The max_bitrate
is obtained by getting a phy attribute.
Link: https://lore.kernel.org/r/20210724174001.553047-1-mkl@pengutronix.de
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
can_validate() does a first check:
| if (is_can_fd) {
| if (!data[IFLA_CAN_BITTIMING] || !data[IFLA_CAN_DATA_BITTIMING])
| return -EOPNOTSUPP;
| }
If that first if succeeds, we know that if is_can_fd is true then
data[IFLA_CAN_BITTIMING is set.
However, the next if switch does not leverage on above knowledge and
redoes the check:
| if (data[IFLA_CAN_DATA_BITTIMING]) {
| if (!is_can_fd || !data[IFLA_CAN_BITTIMING])
| ^~~~~~~~~~~~~~~~~~~~~~~~
| return -EOPNOTSUPP;
| }
This patch removes that redundant check.
Link: https://lore.kernel.org/r/20210603151550.140727-2-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When the FD is turned off through the netlink interface, the data bit
timing values still remain in data_bittiming and are displayed despite
of the feature being disabled.
Example:
| $ ip link set can0 type can bitrate 500000 dbitrate 2000000 fd on
| $ ip --details link show can0
| 1: can0: <NOARP,ECHO> mtu 72 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 10
| link/can promiscuity 0 minmtu 0 maxmtu 0
| can <FD> state STOPPED restart-ms 0
| bitrate 500000 sample-point 0.875
| tq 12 prop-seg 69 phase-seg1 70 phase-seg2 20 sjw 1
| ES582.1/ES584.1: tseg1 2..256 tseg2 2..128 sjw 1..128 brp 1..512 brp-inc 1
| dbitrate 2000000 dsample-point 0.750
| dtq 12 dprop-seg 14 dphase-seg1 15 dphase-seg2 10 dsjw 1
| ES582.1/ES584.1: dtseg1 2..32 dtseg2 1..16 dsjw 1..8 dbrp 1..32 dbrp-inc 1
| clock 80000000 numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
|
| $ ip link set can0 type can bitrate 500000 fd off
| $ ip --details link show can0
| 1: can0: <NOARP,ECHO> mtu 16 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 10
| link/can promiscuity 0 minmtu 0 maxmtu 0
| can state STOPPED restart-ms 0
| bitrate 500000 sample-point 0.875
| tq 12 prop-seg 69 phase-seg1 70 phase-seg2 20 sjw 1
| ES582.1/ES584.1: tseg1 2..256 tseg2 2..128 sjw 1..128 brp 1..512 brp-inc 1
| dbitrate 2000000 dsample-point 0.750
| dtq 12 dprop-seg 14 dphase-seg1 15 dphase-seg2 10 dsjw 1
| ES582.1/ES584.1: dtseg1 2..32 dtseg2 1..16 dsjw 1..8 dbrp 1..32 dbrp-inc 1
| clock 80000000 numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
Remark: once FD is turned off, it is not possible to turn fd back on
and reuse the previously input data bit timing values:
| $ ip link set can0 type can bitrate 500000 fd on
| RTNETLINK answers: Operation not supported
This means that the user will need to re-configure the data bit timing
in order to turn fd on again.
Because old data bit timing values cannot be reused, this patch clears
priv->data_bit timing whenever FD is turned off. This way, the data
bit timing variables are not displayed anymore.
Link: https://lore.kernel.org/r/20210618081904.141114-2-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
After reading all CAN frames from the controller in the IRQ handler
and storing them into a skb_queue, the driver calls napi_schedule().
In the napi poll function the skb from the skb_queue are then pushed
into the networking stack.
However if napi_schedule() is called from a threaded IRQ handler this
triggers the following error:
| NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!!
To avoid this, create a new rx-offload
function (can_rx_offload_threaded_irq_finish()) with a call to
local_bh_disable()/local_bh_enable() around the napi_schedule() call.
Convert all drivers that call can_rx_offload_irq_finish() from
threaded IRQ context to can_rx_offload_threaded_irq_finish().
Link: https://lore.kernel.org/r/20210724204745.736053-4-mkl@pengutronix.de
Suggested-by: Daniel Glöckner <dg@emlix.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Instead of calling can_rx_offload_schedule() call napi_schedule()
directly. As this was the last use of can_rx_offload_schedule() remove
this helper function.
Link: https://lore.kernel.org/r/20210724204745.736053-3-mkl@pengutronix.de
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Adding a skb to the skb_queue in rx-offload requires to take a lock.
This commit avoids this by adding an unlocked skb queue that is
appended at the end of the ISR. Having one lock at the end of the ISR
should be OK as the HW is empty, not about to overflow.
Link: https://lore.kernel.org/r/20210724204745.736053-2-mkl@pengutronix.de
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Co-developed-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Here is the big set of tty and serial driver patches for 5.14-rc1.
A bit more than normal, but nothing major, lots of cleanups. Highlights
are:
- lots of tty api cleanups and mxser driver cleanups from Jiri
- build warning fixes
- various serial driver updates
- coding style cleanups
- various tty driver minor fixes and updates
- removal of broken and disable r3964 line discipline (finally!)
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM4qQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylKvQCfbh+OmTkDlDlDhSWlxuV05M1XTXoAoLUcLZru
s5JCnwSZztQQLMDHj7Pd
=Zupm
-----END PGP SIGNATURE-----
Merge tag 'tty-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is the big set of tty and serial driver patches for 5.14-rc1.
A bit more than normal, but nothing major, lots of cleanups.
Highlights are:
- lots of tty api cleanups and mxser driver cleanups from Jiri
- build warning fixes
- various serial driver updates
- coding style cleanups
- various tty driver minor fixes and updates
- removal of broken and disable r3964 line discipline (finally!)
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (227 commits)
serial: mvebu-uart: remove unused member nb from struct mvebu_uart
arm64: dts: marvell: armada-37xx: Fix reg for standard variant of UART
dt-bindings: mvebu-uart: fix documentation
serial: mvebu-uart: correctly calculate minimal possible baudrate
serial: mvebu-uart: do not allow changing baudrate when uartclk is not available
serial: mvebu-uart: fix calculation of clock divisor
tty: make linux/tty_flip.h self-contained
serial: Prefer unsigned int to bare use of unsigned
serial: 8250: 8250_omap: Fix possible interrupt storm on K3 SoCs
serial: qcom_geni_serial: use DT aliases according to DT bindings
Revert "tty: serial: Add UART driver for Cortina-Access platform"
tty: serial: Add UART driver for Cortina-Access platform
MAINTAINERS: add me back as mxser maintainer
mxser: Documentation, fix typos
mxser: Documentation, make the docs up-to-date
mxser: Documentation, remove traces of callout device
mxser: introduce mxser_16550A_or_MUST helper
mxser: rename flags to old_speed in mxser_set_serial_info
mxser: use port variable in mxser_set_serial_info
mxser: access info->MCR under info->slock
...
Trivial conflict in net/netfilter/nf_tables_api.c.
Duplicate fix in tools/testing/selftests/net/devlink_port_split.py
- take the net-next version.
skmsg, and L4 bpf - keep the bpf code but remove the flags
and err params.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rather than just indicating that transmission can start, this patch
requires the explicit flushing of the network TX queue when the driver
is informed by the device that it can transmit, next to its
configuration.
In this way, if frames have already been written by the application,
they will actually be transmitted.
Fixes: ffd137f704 ("can: peak/pcie_fd: remove useless code when interface starts")
Link: https://lore.kernel.org/r/20210623142600.149904-1-s.grosjean@peak-system.com
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Trivial conflicts in net/can/isotp.c and
tools/testing/selftests/net/mptcp/mptcp_connect.sh
scaled_ppm_to_ppb() was moved from drivers/ptp/ptp_clock.c
to include/linux/ptp_clock_kernel.h in -next so re-apply
the fix there.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Syzbot reported memory leak in SocketCAN driver for Microchip CAN BUS
Analyzer Tool. The problem was in unfreed usb_coherent.
In mcba_usb_start() 20 coherent buffers are allocated and there is
nothing, that frees them:
1) In callback function the urb is resubmitted and that's all
2) In disconnect function urbs are simply killed, but URB_FREE_BUFFER
is not set (see mcba_usb_start) and this flag cannot be used with
coherent buffers.
Fail log:
| [ 1354.053291][ T8413] mcba_usb 1-1:0.0 can0: device disconnected
| [ 1367.059384][ T8420] kmemleak: 20 new suspected memory leaks (see /sys/kernel/debug/kmem)
So, all allocated buffers should be freed with usb_free_coherent()
explicitly
NOTE:
The same pattern for allocating and freeing coherent buffers
is used in drivers/net/can/usb/kvaser_usb/kvaser_usb_core.c
Fixes: 51f3baad7d ("can: mcba_usb: Add support for Microchip CAN BUS Analyzer")
Link: https://lore.kernel.org/r/20210609215833.30393-1-paskripkin@gmail.com
Cc: linux-stable <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+57281c762a3922e14dfe@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Introduce masks for the three RXESC fields (RBDS, F1DS, F0DS) and the
one TXESC field (TBDS). Update m_can_chip_config() to explicitly set all
four fields to the 64-byte option (0x7) (and these defs are renamed to
be more concise).
This is an improvement in maintainability, and also makes it easier to
implement more flexible configuration of the M_CAN buffers in the
future.
Link: https://lore.kernel.org/r/20210504125123.500553-4-torin@maxiluxsystems.com
Signed-off-by: Torin Cooper-Bennun <torin@maxiluxsystems.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Ensures that the different CCCR regmasks for m_can revs 3.0.x, 3.1.x,
3.2.x and 3.3.x are clearly distinguishable. Removes incorrect
CCCR_CANFD define. Adds bit fields UTSU and WMM for rev 3.3.x, for
completeness.
Link: https://lore.kernel.org/r/20210504125123.500553-3-torin@maxiluxsystems.com
Signed-off-by: Torin Cooper-Bennun <torin@maxiluxsystems.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This updates m_can.c to exclusively use GENMASK, FIELD_GET, FIELD_PREP
and FIELD_MAX for regmask ops, as is convention in the current kernel
(far less error-prone, far more concise).
Link: https://lore.kernel.org/r/20210504125123.500553-2-torin@maxiluxsystems.com
Signed-off-by: Torin Cooper-Bennun <torin@maxiluxsystems.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
With commit 132f2d45fb ("can: c_can: add support to 64 message
objects") the number of message objects used for reception /
transmission depends on FIFO size.
The ethtools API support allows you to retrieve this info. Driver info
has been added too.
Link: https://lore.kernel.org/r/20210514165549.14365-2-dariobin@libero.it
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The member rxmasked of struct c_can_priv is initialized by
c_can_chip_config(), but's it's never used, so remove it.
Link: https://lore.kernel.org/r/20210509124309.30024-2-dariobin@libero.it
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
