Use the newly introduced pm_ptr() macro to simplify the code.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some commands uses R1B responses, which means the card may assert the DAT0
line to signal busy for a period of time, after it has received the
command. The mmc core normally specifies the busy period for the command in
the cmd->busy_timeout. Ideally the driver should respect it, but that
requires quite some update of the code, so let's defer that to someone with
the HW at hand.
Instead, let's inform the mmc core about the maximum supported busy timeout
in ->max_busy_timeout during ->probe(). This value corresponds to the fixed
5s timeout used by jz4740. In this way, we let the mmc core validate the
needed timeout, which may lead to that it converts from a R1B into a R1
response and then use CMD13 to poll for busy completion.
In other words, this change enables support for commands with longer busy
periods than 5s, like erase (CMD38) for example.
Cc: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200414161413.3036-5-ulf.hansson@linaro.org
Let's move away from using pinctrl_pm_select_default_state() as it's
scheduled for removal and use pinctrl_select_default_state() instead.
Cc: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191206170821.29711-9-ulf.hansson@linaro.org
Add support for low power mode to the Ingenic's MMC/SD Controller.
Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for probing mmc driver on the X1000 Soc from Ingenic.
Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for probing mmc driver on the JZ4760 Soc from Ingenic.
Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We don't need to set the 'slave_id' anymore - that field is never read
by the DMA driver.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix wrong code indentation which made the code hard to read, and fix
return with value in void function.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-mmc@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version you should have received a copy of the
gnu general public license along with this program if not write to
the free software foundation inc 675 mass ave cambridge ma 02139 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 35 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.655028468@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop the custom code to get the 'cd' and 'wp' GPIOs. The driver now
calls mmc_of_parse() which will init these from devicetree or
device properties.
Also drop the custom code to get the 'power' GPIO. The MMC core
provides us with the means to power the MMC card through an external
regulator.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is a plan to build the kernel with -Wimplicit-fallthrough and
these places in the code produced warnings (W=1).
This commit removes the following warnings:
drivers/mmc/host/jz4740_mmc.c:745:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/mmc/host/jz4740_mmc.c:779:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As reported by Aaro, the JZ4740 MMC driver throws a warning when the kernel
is built without preemption (CONFIG_PREEMPT_NONE=y).
[ 16.461094] jz4740-mmc 13450000.mmc: [jz4740_mmc_prepare_dma_data] invalid cookie: data->host_cookie 567 host->next_data.cookie 568
[ 16.473120] jz4740-mmc 13450000.mmc: [jz4740_mmc_prepare_dma_data] invalid cookie: data->host_cookie 568 host->next_data.cookie 569
[ 16.485144] jz4740-mmc 13450000.mmc: [jz4740_mmc_prepare_dma_data] invalid cookie: data->host_cookie 569 host->next_data.cookie 570
[ 16.497170] jz4740-mmc 13450000.mmc: [jz4740_mmc_prepare_dma_data] invalid cookie: data->host_cookie 570 host->next_data.cookie 571
The problem seems to be related to how pre_req/post_req is implemented.
Currently, it seems the driver expects jz4740_mmc_prepare_dma_data() to be
called with monotonically increasing host_cookie values, which is wrong.
Moreover, the implementation is overly complicated, keeping track of
unneeded "next cookie" state.
So, instead of attempting to fix the current pre_req/post_req
implementation, this commit refactors the driver, dropping the state,
following other drivers such as dw_mmc and sdhci.
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Mathieu Malaterre <malat@debian.org>
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The power GPIO line is passed with inversion flags and all from
the platform data. Switch to using an optional GPIO descriptor and
use this to switch the power.
Augment the only boardfile to pass in the proper "power" descriptor
in the GPIO descriptor machine table instead.
As the GPIO handling is now much simpler, we can cut down on some
overhead code.
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: linux-mips@linux-mips.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Modifty the JZ4740 driver to retrieve card detect and write
protect GPIO pins from GPIO descriptors instead of hard-coded
global numbers. Augment the only board file using this in the
process and cut down on passed in platform data.
Preserve the code setting the caps2 flags for CD and WP
as active low or high since the slot GPIO code currently
ignores the gpiolib polarity inversion semantice and uses
the raw accessors to read the GPIO lines, but set the right
polarity flags in the descriptor table for jz4740.
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: linux-mips@linux-mips.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The JZ4725B is the first JZ SoC version that introduced a 32-bit IMASK
register, not the JZ4750.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Replace dma_request_channel() with dma_request_chan(),
which also supports probing from the devicetree.
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for the JZ4780 MMC controller to the jz47xx_mmc driver. There
are a few minor differences from the 4740 to the 4780 that need to be
handled, but otherwise the controllers behave the same. The IREG and IMASK
registers are expanded to 32 bits. Additionally, some error conditions are
now reported in both STATUS and IREG. Writing IREG before reading STATUS
causes the bits in STATUS to be cleared, so STATUS must be read first to
ensure we see and report error conditions correctly.
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The maximum clock rate can be overridden by DT. The clock rate should
be set to the DT-specified value rather than the constant JZ_MMC_CLK_RATE
when this is done. If the maximum clock rate is not set by DT then
mmc->f_max will be set to JZ_MMC_CLK_RATE.
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support to probe the device via devicetree, which
will be used to support other SoCs such as the JZ4780.
Based on commits from the CI20 repo, by Paul Cercueil
and Alex Smith. Binding document based on work by
Zubair Lutfullah Kakakhel.
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In case a bootloader leaves the device in a bad state,
requesting the interrupt before resetting results in a bad
interrupt loop.
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
[Ezequiel: cleanup commit description]
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of accessing the platform data pointer directly,
use the dev_get_platdata() helper.
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Just a minor cleanup to order the headers alphabetically.
This helps prevent merge conflicts.
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, if jz4740_mmc_request_gpios() fails, the driver
tries to release DMA resources. This is wrong because DMA
is requested at a later stage.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
[Ezequiel: cleanup commit message]
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A spinlock is held while updating the internal copy of the IRQ mask,
but not while writing it to the actual IMASK register. After the lock
is released, an IRQ can occur before the IMASK register is written.
If handling this IRQ causes the mask to be changed, when the handler
returns back to the middle of the first mask update, a stale value
will be written to the mask register.
If this causes an IRQ to become unmasked that cannot have its status
cleared by writing a 1 to it in the IREG register, e.g. the SDIO IRQ,
then we can end up stuck with the same IRQ repeatedly being fired but
not handled. Normally the MMC IRQ handler attempts to clear any
unexpected IRQs by writing IREG, but for those that cannot be cleared
in this way then the IRQ will just repeatedly fire.
This was resulting in lockups after a while of using Wi-Fi on the
CI20 (GitHub issue #19).
Resolve by holding the spinlock until after the IMASK register has
been updated.
Cc: stable@vger.kernel.org
Link: https://github.com/MIPS/CI20_linux/issues/19
Fixes: 61bfbdb856 ("MMC: Add support for the controller on JZ4740 SoCs.")
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Bruce Chang <brucechang@via.com.tw>
Cc: Harald Welte <HaraldWelte@viatech.com>
Cc: Tony Olech <tony.olech@elandigitalsystems.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Arvind Yadav <arvind.yadav.cs@gmail.com>
Cc: Allen <allen.lkml@gmail.com>
Cc: linux-mmc@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-amlogic@lists.infradead.org
Cc: linux-omap@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that the JZ4740 and similar SoCs have a pinctrl driver, we rely on
the pins being properly configured before the driver probes.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The void (*pre_req) callback in the struct mmc_host_ops vtable
is passing an argument "is_first_req" indicating whether this is
the first request or not.
None of the in-kernel users use this parameter: instead, since
they all just do variants of dma_map* they use the DMA cookie
to indicate whether a pre* callback has already been done for
a request when they decide how to handle it.
Delete the parameter from the callback and all users, as it is
just pointless cruft.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We now have implicit batching in the timer wheel. The slack API is no longer
used, so remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Chris Mason <clm@fb.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: George Spelvin <linux@sciencehorizons.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-block@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mmc@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160704094342.189813118@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Remove the MMC_DATA_STREAM flag because it isn't used anymore.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Make use of the MMC asynchronous request capability to prepare the
next DMA transfer request in parallel with the current transfer.
This is done by adding pre-request and post-request callbacks that are
used by the MMC framework during an active data transfer.
It should help reduce the impact of DMA preparation overhead on the SD
card performance.
Signed-off-by: Apelete Seketeli <apelete@seketeli.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Until now the MMC driver for JZ4740 SoC was relying on PIO mode only
for data transfers.
This patch allows the use of DMA for data trasnfers in addition to PIO
mode by relying on DMA Engine.
DMA tranfers performance might be further improved by taking advantage
of the asynchronous request capability of the MMC framework.
Signed-off-by: Apelete Seketeli <apelete@seketeli.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As of commit bcc3e1726d ("mmc: block: Use R1 responses for stop cmds for
read requests"), stop commands for reads do not have MMC_RSP_BUSY set.
In this case we should not wait for a PRG_DONE IRQ after sending the
stop command: it will not get raised when the busy flag is not set,
causing the request to fail with a timeout.
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Chris Ball <chris@printf.net>
Cc: James Hogan <james.hogan@imgtec.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Suspend and resume of cards are being handled from the protocol layer
and consequently the mmc_suspend|resume_host APIs are deprecated.
This means we can simplify the suspend|resume callbacks by removing the
use of the deprecated APIs.
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add a debounce parameter to the mmc_gpio_request_cd() function that
enables GPIO debouncing when set to a non-zero value. This can be used
by MMC host drivers to enable debouncing on the card detect signal.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR(). Also there is already a error message within
devm_ioremap_resource(), so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Chris Ball <cjb@laptop.org>
Use managed resources for the mmio memory region and the clock.
Makes the code a bit shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Use the slot-gpio helpers to handle the write protect and card detect
GPIO pins instead of re-implementing the same functionality in the driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
It's a bit shorter than open-conding it. While we are at it also make
jz4740_mmc_pm_ops static.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
For no reason, the code handling write errors was implemented while
the code handling read errors was missing.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
In preparation to switching the jz4740 clk driver to the
common clk framework, update the clk enable/disable calls
to clk_prepare_enable/clk_disable_unprepare.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Chris Ball <cjb@laptop.org>
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Venkatraman S <svenkatr@ti.com>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: Bruce Chang <brucechang@via.com.tw>
Cc: Harald Welte <HaraldWelte@viatech.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Chris Ball <cjb@laptop.org>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Venkatraman S <svenkatr@ti.com>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: Bruce Chang <brucechang@via.com.tw>
Cc: Harald Welte <HaraldWelte@viatech.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Chris Ball <cjb@laptop.org>
Cc: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Venkatraman S <svenkatr@ti.com>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: Bruce Chang <brucechang@via.com.tw>
Cc: Harald Welte <HaraldWelte@viatech.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>