Commit Graph

131 Commits

Author SHA1 Message Date
Angelo Dureghello
a5a944d24c mmc: host: add Coldfire esdhc support
This driver has been developed as a separate module starting
from the similar sdhci-esdhc-imx.c.

Reasons for a separate sdchi-esdhc-mcf driver:

- m68K architecture does not support devicetrees, so modifying
sdhci-of-esdhc.c that is devicetree-related adding platform data
seems not appropriate,
- clock-related part, has to be implemented specifically for
mcf5441x family (see esdhc_mcf_pltfm_set_clock()),
- this is a big endian cpu accessing a big endian controller,
but about sdma, this controller does not support hw swap, which
needs to be handled with specific code,
- some other minor differences but mainly to avoid risks on
tweaking inside largely used imx driver. Adding just a small
size ColdFire-specific driver, with benefits in a further less
risky maintenance.

Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200518191742.1251440-3-angelo.dureghello@timesys.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2020-05-28 11:22:15 +02:00
Martin Blumenstingl
67c7daec69 mmc: meson-mx-sdhc: Fix building with CONFIG_MMC_MESON_MX_SDHC=m
For an x86_64 allmodconfig build Stephen reports that building
meson-mx-sdhc-clkc.o warns that MODULE_LICENSE is missing and when
linking meson_mx_sdhc_register_clkc cannot be found.

Compile the MMC controller driver together with the build-in clock
controller driver into one module rather than using two separate
modules to fix these issues.

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20200518060811.1499962-1-martin.blumenstingl@googlemail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2020-05-28 11:22:14 +02:00
Martin Blumenstingl
e4bf1b0970 mmc: host: meson-mx-sdhc: new driver for the Amlogic Meson SDHC host
The SDHC MMC host controller on Amlogic SoCs provides an eMMC and MMC
card interface with 1/4/8-bit bus width.
It supports eMMC spec 4.4x/4.5x including HS200 (up to 100MHz clock).

The public S805 datasheet [0] contains a short documentation about the
registers. Unfortunately it does not describe how to use the registers
to make the hardware work. Thus this driver is based on reading (and
understanding) the Amlogic 3.10 GPL kernel code.

Some hardware details are not easy to see. Jianxin Pan was kind enough
to answer my questions:
The hardware has built-in busy timeout support. The maximum timeout is
30 seconds. This is only documented in Amlogic's internal
documentation.

The controller only works with very specific clock configurations. The
details are not part of the public datasheet. In my own words the
supported configurations are:
- 399.812kHz:	clkin =  850MHz div = 2126 sd_rx_phase = 63
- 1MHz:		clkin =  850MHz div = 850  sd_rx_phase = 55
- 5.986MHz:	clkin =  850MHz div = 142  sd_rx_phase = 24
- 25MHz:	clkin =  850MHz div = 34   sd_rx_phase = 15
- 47.222MHz:	clkin =  850MHz div = 18   sd_rx_phase = 11/15 (SDR50/HS)
- 53.125MHz:	clkin =  850MHz div = 16   sd_rx_phase = (tuning)
- 70.833MHz:	clkin =  850MHz div = 12   sd_rx_phase = (tuning)
- 85MHz:	clkin =  850MHz div = 10   sd_rx_phase = (tuning)
- 94.44MHz:	clkin =  850MHz div = 9    sd_rx_phase = (tuning)
- 106.25MHz:	clkin =  850MHz div = 8    sd_rx_phase = (tuning)
- 127.5MHz:     clkin = 1275MHz div = 10   sd_rx_phase = (tuning)
- 141.667MHz:   clkin =  850MHz div = 6    sd_rx_phase = (tuning)
- 159.375MHz:	clkin = 1275MHz div = 8    sd_rx_phase = (tuning)
- 212.5MHz:	clkin = 1275MHz div = 6    sd_rx_phase = (tuning)
- (sd_tx_phase is always 1, 94.44MHz is not listed in the datasheet
   but this is what the 3.10 BSP kernel on Odroid-C1 actually uses)

NOTE: CMD23 support is disabled for now because it results in command
timeouts and thus decreases read performance.

Tested-by: Wei Wang <lnykww@gmail.com>
Tested-by: Xin Yin <yinxin_1989@aliyun.com>
Reviewed-by: Xin Yin <yinxin_1989@aliyun.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20200512204147.504087-3-martin.blumenstingl@googlemail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2020-05-28 11:22:14 +02:00
Baolin Wang
511ce378e1 mmc: Add MMC host software queue support
Now the MMC read/write stack will always wait for previous request is
completed by mmc_blk_rw_wait(), before sending a new request to hardware,
or queue a work to complete request, that will bring context switching
overhead and spend some extra time to poll the card for busy completion
for I/O writes via sending CMD13, especially for high I/O per second
rates, to affect the IO performance.

Thus this patch introduces MMC software queue interface based on the
hardware command queue engine's interfaces, which is similar with the
hardware command queue engine's idea, that can remove the context
switching. Moreover we set the default queue depth as 64 for software
queue, which allows more requests to be prepared, merged and inserted
into IO scheduler to improve performance, but we only allow 2 requests
in flight, that is enough to let the irq handler always trigger the
next request without a context switch, as well as avoiding a long latency.

Moreover the host controller should support HW busy detection for I/O
operations when enabling the host software queue. That means, the host
controller must not complete a data transfer request, until after the
card stops signals busy.

From the fio testing data in cover letter, we can see the software
queue can improve some performance with 4K block size, increasing
about 16% for random read, increasing about 90% for random write,
though no obvious improvement for sequential read and write.

Moreover we can expand the software queue interface to support MMC
packed request or packed command in future.

Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/4409c1586a9b3ed20d57ad2faf6c262fc3ccb6e2.1581478568.git.baolin.wang7@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2020-03-24 14:35:39 +01:00
Manivannan Sadhasivam
ff65ffe46d mmc: Add Actions Semi Owl SoCs SD/MMC driver
Add SD/MMC driver for Actions Semi Owl SoCs. This driver currently
supports standard, high speed, SDR12, SDR25 and SDR50. DDR50 mode is
supported but it is untested. There is no SDIO support for now.

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-11-13 16:10:16 +01:00
Takao Orito
dd79b7e367 mmc: sdhci-milbeaut: add Milbeaut SD controller driver
SD Host controller on Milbeaut consists of two controller parts.
One is core controller F_SDH30, this is similar to sdhci-fujitsu
controller.
Another is bridge controller.
This bridge controller is not compatible with sdhci-fujitsu controller.
This is special for Milbeaut series. This has some functions.
For example, reset control, clock enable/select for SDR50/25/12, set
property of SD physical pins, retuning control, set capabilityies.

This bridge controller requires special procedures at reset or clock
enablement or change for further tuning of clock.

Signed-off-by: Takao Orito <orito.takao@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-11-13 16:10:16 +01:00
Ben Chuang
e51df6ce66 mmc: host: sdhci-pci: Add Genesys Logic GL975x support
Add support for the GL9750 and GL9755 chipsets.

Enable v4 mode and wait 5ms after set 1.8V signal enable for GL9750/
GL9755. Fix the value of SDHCI_MAX_CURRENT register and use the vendor
tuning flow for GL9750.

Co-developed-by: Michael K Johnson <johnsonm@danlj.org>
Signed-off-by: Michael K Johnson <johnsonm@danlj.org>
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-09-27 20:48:20 +02:00
Andrew Jeffery
bb7b8ec62d mmc: sdhci-of-aspeed: Add support for the ASPEED SD controller
Add a minimal driver for ASPEED's SD controller, which exposes two
SDHCIs.

The ASPEED design implements a common register set for the SDHCIs, and
moves some of the standard configuration elements out to this common
area (e.g. 8-bit mode, and card detect configuration which is not
currently supported).

The SD controller has a dedicated hardware interrupt that is shared
between the slots. The common register set exposes information on which
slot triggered the interrupt; early revisions of the patch introduced an
irqchip for the register, but reality is it doesn't behave as an
irqchip, and the result fits awkwardly into the irqchip APIs. Instead
I've taken the simple approach of using the IRQ as a shared IRQ with
some minor performance impact for the second slot.

Ryan was the original author of the patch - I've taken his work and
massaged it to drop the irqchip support and rework the devicetree
integration. The driver has been smoke tested under qemu against a
minimal SD controller model and lightly tested on an ast2500-evb.

Signed-off-by: Ryan Chen <ryanchen.aspeed@gmail.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-09-11 15:58:39 +02:00
Faiz Abbas
41fd4caeb0 mmc: sdhci_am654: Add Initial Support for AM654 SDHCI driver
The host controllers on TI's AM654 SOCs are not compatible with
the phy and consumer model of the sdhci-of-arasan driver. It turns out
that for optimal operation at higher speeds, a special tuning procedure
needs to be implemented which involves configuration of platform
specific phy registers.

Therefore, branch out to a new sdhci_am654 driver and add the phy
register space with all phy configurations to it. Populate AM654
specific callbacks to sdhci_ops and add SDHCI_QUIRKS wherever
applicable.

Only add support for upto High Speed for SD card and upto DDR52 speed
mode for eMMC. Higher speeds will be added in subsequent patches.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-12-17 08:26:24 +01:00
Oleksij Rempel
c5413ad815 mmc: add new Alcor Micro Cardreader SD/MMC driver
This driver provides support for Alcor Micro AU6601 and AU6621
SD/MMC controller.

Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-12-17 08:26:24 +01:00
Ludovic Barre
46b723dd86 mmc: mmci: add stm32 sdmmc variant
This patch adds a stm32 sdmmc variant, rev 1.1.
Introduces a new Manufacturer id "0x53, ascii 'S' to define
new stm32 sdmmc family with clean range of amba
revision/configurations bits (corresponding to sdmmc_ver
register with major/minor fields).
Add 2 variants properties:
-dma_lli, to enable link list support.
-stm32_idmabsize_mask, defines the range of SDMMC_IDMABSIZER register
 which specify the number bytes per buffer.

DT properties for sdmmc:
-Indicate signal directions (only one property
 for d0dir, d123dir, cmd_dir)
-Select command and data phase relation.
-Select "clock in" from an external driver.

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-10-09 09:16:53 +02:00
Chunyan Zhang
fb8bd90f83 mmc: sdhci-sprd: Add Spreadtrum's initial host controller
This patch adds the initial support of Secure Digital Host Controller
Interface compliant controller found in some latest Spreadtrum chipsets.
This patch has been tested on the version of SPRD-R11 controller.

R11 is a variant based on SD v4.0 specification.

With this driver, R11 mmc can be initialized, can be mounted, read and
written.

Original-by: Billows Wu <billows.wu@unisoc.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-10-08 11:40:43 +02:00
Masahiro Yamada
3fd784f745 mmc: uniphier-sd: add UniPhier SD/eMMC controller driver
Here is another TMIO MMC variant found in Socionext UniPhier SoCs.

As commit b6147490e6 ("mmc: tmio: split core functionality, DMA and
MFD glue") said, these MMC controllers use the IP from Panasonic.

However, the MMC controller in the TMIO (Toshiba Mobile IO) MFD chip
was the first upstreamed user of this IP.  The common driver code
for this IP is now called 'tmio-mmc-core' in Linux although it is a
historical misnomer.

Anyway, this driver select's MMC_TMIO_CORE to borrow the common code
from tmio-mmc-core.c

Older UniPhier SoCs (LD4, Pro4, sLD8) support the external DMA engine
like renesas_sdhi_sys_dmac.c.  The difference is UniPhier SoCs use a
single DMA channel whereas Renesas chips request separate channels for
RX and TX.

Newer UniPhier SoCs (Pro5 and later) support the internal DMA engine
like renesas_sdhi_internal_dmac.c  The register map is almost the same,
so I guess Renesas and Socionext use the same internal DMA hardware.
The main difference is, the register offsets are doubled for Renesas.

                        Renesas      Socionext
                        SDHI         UniPhier
  DM_CM_DTRAN_MODE      0x820        0x410
  DM_CM_DTRAN_CTRL      0x828        0x414
  DM_CM_RST             0x830        0x418
  DM_CM_INFO1           0x840        0x420
  DM_CM_INFO1_MASK      0x848        0x424
  DM_CM_INFO2           0x850        0x428
  DM_CM_INFO2_MASK      0x858        0x42c
  DM_DTRAN_ADDR         0x880        0x440
  DM_DTRAN_ADDREX        ---         0x444

This comes from the difference of host->bus_shift; 2 for Renesas SoCs,
and 1 for UniPhier SoCs.  Also, the datasheet for UniPhier SoCs defines
DM_DTRAN_ADDR and DM_DTRAN_ADDREX as two separate registers.

It could be possible to factor out the DMA common code by introducing
some hooks to cope with platform quirks, but this patch does not touch
that for now.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-10-08 11:40:43 +02:00
Prabu Thangamuthu
152f8204ff mmc: sdhci-pci-dwc-mshc: synopsys dwc mshc support
Synopsys has DWC MSHC controller on HPAS-DX platform connected using PCIe
interface with SD card slot and eMMC device slots. This patch is to
enable SD cards connected on this platform. As Clock generation logic
is implemented using MMCM module of HAPS-DX platform, we have separate
functions to control the MMCM to generate required clocks with respect
to speed mode.

Signed-off-by: Prabu Thangamuthu <prabu.t@synopsys.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-07-16 11:21:45 +02:00
Jisheng Zhang
e438cf49b3 mmc: sdhci-of-dwcmshc: add SDHCI OF Synopsys DWC MSHC driver
Add a driver for SDHCI OF Synopsys DesignWare Cores Mobile Storage

Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
2018-07-16 11:21:45 +02:00
Liming Sun
86958dcc5a mmc: dw_mmc-bluefield: Add driver extension
This commit adds extension to the dw_mmc driver for Mellanox BlueField
SoC. It updates the UHS_REG_EXT register to bring up the eMMC card on
this SoC.

Signed-off-by: Liming Sun <lsun@mellanox.com>
Reviewed-by: David Woods <dwoods@mellanox.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-21 10:44:40 +02:00
Linus Torvalds
dc73d6a8d4 MMC core:
- Export host capabilities through debugfs
  - Export card RCA register via sysfs
  - Improve card initializing sequence while enabling 4-bit bus
  - Export a function to enable/disable wakeup for card detect IRQ
 
 MMC host:
  - dw_mmc: Add support for new hi3798cv200 variant
  - dw_mmc: Remove support for some deprecated DT properties
  - mediatek: Add support for new variant used on MT7622 SoC
  - sdhci: Improve wakeup support for SDIO IRQs
  - sdhci: Improve wakeup support for card detect IRQs
  - sdhci-omap: Add tuning support
  - sdhci_omap: Add UHS-I mode support
  - sunxi: Prepare for runtime PM support via a few re-factorings
  - tmio: deprecate "toshiba,mmc-wrprotect-disable" DT property
  - tmio/renesas_sdhi: Consolidate code supporting write protect
  - tmio: Improve DMA vs PIO handling
  - tmio: Add support for IP-builtin card detection logic
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJaw0MuAAoJEP4mhCVzWIwpW78P/2N2qPt21OfvnIbSexY1nyPd
 5+rjScgy+oTUnNxITA9LOnM4P6Wg/9PgvhjUdNdHzd5ZaXIchw372+Xu6hZHdujI
 vBfnpsI/xtyL1TQ6nvJc9b+Sp4W4LL2MlCqxi+btAKLvTAU3NNm7uJRRP6xRNDd5
 8wcsCoIN4C3k5hmh5++DDLCfuzpwmbC1cEbGtL/QEV9xeCY5+fJq4Qpq14L2TJ0g
 LeDls3X4HAJa3SsgSGOdNr8rttKUSS+j7i1XsShHMyq89DD21PJ8fvMhdzlXJub9
 A4PatcOXALS/Xd2YVjeLHrRRlTitssD+Sllt46NsB4eJJOO+DempecY+i0WoW60y
 p9IUSSX86yokGoyweiL2GI0Ja1Bg8xgdzTGVbfZ6w6UKHjQAcItnojyMghDM5+zt
 VjDIU59rzm+BEDqcktsbGgLPjOZ0ZWgJPPp2NPkechxsojvCJ9Smm6yPjzaUnZ60
 U9PxsYbs4NB+nE9iKDioyA1ABP0N+BloUkTf/cVHdPBBPMmOyI7jYEDS7mqollZU
 bQCFx+BqcQMbnvI/TZxNDTr4HsiyiXJa0GTCB77sge8tZdcUTjUsWyhc+BYpIqgA
 68/dlwTcawSXDliup5XxtYcAjGugtHbPnS/39uBXvscqWVej1WI5RTyzKdC/hnos
 BP5uz0K1Wic1Dl+jqlWc
 =2Pd6
 -----END PGP SIGNATURE-----

Merge tag 'mmc-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc

Pull MMC updates from Ulf Hansson:
 "MMC core:
   - Export host capabilities through debugfs
   - Export card RCA register via sysfs
   - Improve card initializing sequence while enabling 4-bit bus
   - Export a function to enable/disable wakeup for card detect IRQ

  MMC host:
   - dw_mmc: Add support for new hi3798cv200 variant
   - dw_mmc: Remove support for some deprecated DT properties
   - mediatek: Add support for new variant used on MT7622 SoC
   - sdhci: Improve wakeup support for SDIO IRQs
   - sdhci: Improve wakeup support for card detect IRQs
   - sdhci-omap: Add tuning support
   - sdhci_omap: Add UHS-I mode support
   - sunxi: Prepare for runtime PM support via a few re-factorings
   - tmio: deprecate "toshiba,mmc-wrprotect-disable" DT property
   - tmio/renesas_sdhi: Consolidate code supporting write protect
   - tmio: Improve DMA vs PIO handling
   - tmio: Add support for IP-builtin card detection logic"

* tag 'mmc-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (55 commits)
  mmc: renesas_sdhi: replace EXT_ACC with HOST_MODE
  mmc: update sdio_claim_irq documentation
  mmc: Export host capabilities to debugfs.
  mmc: core: Disable HPI for certain Micron (Numonyx) eMMC cards
  mmc: block: fix updating ext_csd caches on ioctl call
  mmc: sunxi: Set our device drvdata earlier
  mmc: sunxi: Move the reset deassertion before enabling the clocks
  mmc: sunxi: Move resources management to separate functions
  mmc: dw_mmc: add support for hi3798cv200 specific extensions of dw-mshc
  dt-bindings: mmc: add bindings for hi3798cv200-dw-mshc
  mmc: core: Export card RCA register via sysfs
  mmc: renesas_sdhi: fix WP detection
  mmc: core: Use memdup_user() rather than duplicating its implementation
  mmc: dw_mmc-rockchip: correct property names in debug
  mmc: sd: Remove redundant err assignment from mmc_read_switch
  mmc: sdio: Check the return value of sdio_enable_4bit_bus
  mmc: core: Don't try UHS-I mode if 4-bit mode isn't supported
  arm64: dts: hi3660: remove 'num-slots' property for dwmmc
  ARM: dts: lpc18xx: remove 'num-slots' property for dwmmc
  arm64: dts: stratix10: remove 'num-slots' property for dwmmc
  ...
2018-04-03 12:17:25 -07:00
Arnd Bergmann
7ec164a18d mmc: remove bfin_sdh driver
The blackfin architecture is getting removed, so this one
is obsolete now as well.

Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Aaron Wu <aaron.wu@analog.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2018-03-26 15:57:00 +02:00
tianshuliang
e382ab7412 mmc: dw_mmc: add support for hi3798cv200 specific extensions of dw-mshc
Hi3798CV200 SoC extends the dw-mshc controller for additional clock
and bus control. Add support for these extensions.

Signed-off-by: tianshuliang <tianshuliang@hisilicon.com>
Signed-off-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-03-15 14:43:22 +01:00
Atul Garg
d72d72cd33 mmc:host:sdhci-pci:Addition of Arasan PCI Controller with integrated phy.
The Arasan Controller is based on a FPGA platform and has integrated phy
with specific registers used during initialization and
management of different modes. The phy and the controller are integrated
and registers are very specific to Arasan.

Arasan being an IP provider, licenses these IPs to various companies for
integration of IP in custom SOCs. The custom SOCs define own register
map depending on how bits are tied inside the SOC for phy registers,
depending on SOC memory plan and hence will require own platform drivers.

If more details on phy registers are required, an interface document is
hosted at https://arasan.com/NF/eMMC5.1 PHY Programming in Linux.pdf.

Signed-off-by: Atul Garg <agarg@arasan.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-01-04 12:46:11 +01:00
Masahiro Yamada
c813e10a6b mmc: renesas_sdhi: consolidate DMAC CONFIG options
The description in the Makefile is odd.  Fix the CONFIG selection
in a cleaner way.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-12-15 09:30:38 +01:00
Venkat Gopalakrishnan
a4080225f5 mmc: cqhci: support for command queue enabled host
This patch adds CMDQ support for command-queue compatible
hosts.

Command queue is added in eMMC-5.1 specification. This
enables the controller to process upto 32 requests at
a time.

Adrian Hunter contributed renaming to cqhci, recovery, suspend
and resume, cqhci_off, cqhci_wait_for_idle, and external timeout
handling.

Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Konstantin Dorfman <kdorfman@codeaurora.org>
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
2017-12-11 12:44:34 +01:00
Linus Torvalds
dee02770cd MMC core:
- Introduce host claiming by context to support blkmq
  - Preparations for enabling CQE (eMMC CMDQ) requests
  - Re-factorizations to prepare for blkmq support
  - Re-factorizations to prepare for CQE support
  - Fix signal voltage switch for SD cards without power cycle
  - Convert RPMB to a character device
  - Export eMMC revision via sysfs
  - Support eMMC DT binding for fixed driver type
  - Document mmc_regulator_get_supply() API
 
 MMC host:
  - omap_hsmmc: Updated regulator management for PBIAS
  - sdhci-omap: Add new OMAP SDHCI driver
  - meson-mx-sdio: New driver for the Amlogic Meson8 and Meson8b SoCs
  - sdhci-pci: Add support for Intel CDF
  - sdhci-acpi: Fix voltage switch for some Intel host controllers
  - sdhci-msm: Enable delay circuit calibration clocks
  - sdhci-msm: Manage power IRQ properly
  - mediatek: Add support of mt2701/mt2712
  - mediatek: Updates management of clocks and tunings
  - mediatek: Upgrade eMMC HS400 support
  - rtsx_pci: Update tuning for gen3 PCI-Express
  - renesas_sdhi: Support R-Car Gen[123] fallback compatibility strings
  - Catch all errors when getting regulators
  - Various additional improvements and cleanups
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJaCXiaAAoJEP4mhCVzWIwp+c4P/3UptZJJScU4WFS1zXH8h/YK
 mYQ4DOCZqQYihKV4ssbAAjmTkT3RdMkl+rq2s5+ZfVbsu57UqeHNaNXBQWirkXCo
 xBDzZlZFz42g4apKq+ZfmewZTM2fjed8Z7SrDcxPkkyU90QKa/LFFleAyxyXxXr1
 ubKHJtev/oWBRxvzvWPYNUI5ExraxGxp2iGvavoYHNcggAgOSBJoKESvF7er5MRK
 Cx5cuKAESU2dJFQnebjndx3dFgQsZ18RTRXUom50oP3BXF2G3gIBMjxp9VfyuOGV
 xedyE2ALQxr1bxyWWejMdhhiZ+eNZNtiEJKqJ37ArTeBDyDfO/SDVXlkqkAARlYW
 rTzh9olfbuhFdCAo2gxAcCaQXnjgQzDDKnQJs++tQVziXGI9ezc44+A6fNh39nre
 yc/MLIjN96vWRhhFuTeFuENN+n7D2xyy+keXZXrALYYOCPAlKtip6DOgVl3ltNvx
 K1O7/STqdR4OHLK6vgdzi9ai3PmcmSBQwKCqqCH/7mcFm1xtBcxqdrEwORLQ3lCH
 c/tl4lJqJR2BD8U9gipjik0ovWb5p2KKAYhjqEY2qMy14OXs2509Y8GcqQRzqcQc
 FSAfUInooHfDEbUBVsLpTOjMvd6LAx34fTJ9QAanAZ1wdeV8C9DRz3kJh/L/mOmG
 N7/jyJnMV1Izknmpc2MP
 =3Gvx
 -----END PGP SIGNATURE-----

Merge tag 'mmc-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc

Pull MMC updates from Ulf Hansson:
 "MMC core:
   - Introduce host claiming by context to support blkmq
   - Preparations for enabling CQE (eMMC CMDQ) requests
   - Re-factorizations to prepare for blkmq support
   - Re-factorizations to prepare for CQE support
   - Fix signal voltage switch for SD cards without power cycle
   - Convert RPMB to a character device
   - Export eMMC revision via sysfs
   - Support eMMC DT binding for fixed driver type
   - Document mmc_regulator_get_supply() API

 MMC host:
   - omap_hsmmc: Updated regulator management for PBIAS
   - sdhci-omap: Add new OMAP SDHCI driver
   - meson-mx-sdio: New driver for the Amlogic Meson8 and Meson8b SoCs
   - sdhci-pci: Add support for Intel CDF
   - sdhci-acpi: Fix voltage switch for some Intel host controllers
   - sdhci-msm: Enable delay circuit calibration clocks
   - sdhci-msm: Manage power IRQ properly
   - mediatek: Add support of mt2701/mt2712
   - mediatek: Updates management of clocks and tunings
   - mediatek: Upgrade eMMC HS400 support
   - rtsx_pci: Update tuning for gen3 PCI-Express
   - renesas_sdhi: Support R-Car Gen[123] fallback compatibility strings
   - Catch all errors when getting regulators
   - Various additional improvements and cleanups"

* tag 'mmc-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (91 commits)
  sdhci-fujitsu: add support for setting the CMD_DAT_DELAY attribute
  dt-bindings: sdhci-fujitsu: document cmd-dat-delay property
  mmc: tmio: Replace msleep() of 20ms or less with usleep_range()
  mmc: dw_mmc: Convert timers to use timer_setup()
  mmc: dw_mmc: Cleanup the DTO timer like the CTO one
  mmc: vub300: Use common code in __download_offload_pseudocode()
  mmc: tmio: Use common error handling code in tmio_mmc_host_probe()
  mmc: Convert timers to use timer_setup()
  mmc: sdhci-acpi: Fix voltage switch for some Intel host controllers
  mmc: sdhci-acpi: Let devices define their own private data
  mmc: mediatek: perfer to use rise edge latching for cmd line
  mmc: mediatek: improve eMMC hs400 mode read performance
  mmc: mediatek: add latch-ck support
  mmc: mediatek: add support of source_cg clock
  mmc: mediatek: add stop_clk fix and enhance_rx support
  mmc: mediatek: add busy_check support
  mmc: mediatek: add async fifo and data tune support
  mmc: mediatek: add pad_tune0 support
  mmc: mediatek: make hs400_tune_response only for mt8173
  arm64: dts: mt8173: remove "mediatek, mt8135-mmc" from mmc nodes
  ...
2017-11-13 10:17:35 -08:00
Greg Kroah-Hartman
b24413180f License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier.  The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
 - file had no licensing information it it.
 - file was a */uapi/* one with no licensing information in it,
 - file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne.  Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed.  Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
 - Files considered eligible had to be source code files.
 - Make and config files were included as candidates if they contained >5
   lines of source
 - File already had some variant of a license header in it (even if <5
   lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

 - when both scanners couldn't find any license traces, file was
   considered to have no license information in it, and the top level
   COPYING file license applied.

   For non */uapi/* files that summary was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0                                              11139

   and resulted in the first patch in this series.

   If that file was a */uapi/* path one, it was "GPL-2.0 WITH
   Linux-syscall-note" otherwise it was "GPL-2.0".  Results of that was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0 WITH Linux-syscall-note                        930

   and resulted in the second patch in this series.

 - if a file had some form of licensing information in it, and was one
   of the */uapi/* ones, it was denoted with the Linux-syscall-note if
   any GPL family license was found in the file or had no licensing in
   it (per prior point).  Results summary:

   SPDX license identifier                            # files
   ---------------------------------------------------|------
   GPL-2.0 WITH Linux-syscall-note                       270
   GPL-2.0+ WITH Linux-syscall-note                      169
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause)    21
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause)    17
   LGPL-2.1+ WITH Linux-syscall-note                      15
   GPL-1.0+ WITH Linux-syscall-note                       14
   ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause)    5
   LGPL-2.0+ WITH Linux-syscall-note                       4
   LGPL-2.1 WITH Linux-syscall-note                        3
   ((GPL-2.0 WITH Linux-syscall-note) OR MIT)              3
   ((GPL-2.0 WITH Linux-syscall-note) AND MIT)             1

   and that resulted in the third patch in this series.

 - when the two scanners agreed on the detected license(s), that became
   the concluded license(s).

 - when there was disagreement between the two scanners (one detected a
   license but the other didn't, or they both detected different
   licenses) a manual inspection of the file occurred.

 - In most cases a manual inspection of the information in the file
   resulted in a clear resolution of the license that should apply (and
   which scanner probably needed to revisit its heuristics).

 - When it was not immediately clear, the license identifier was
   confirmed with lawyers working with the Linux Foundation.

 - If there was any question as to the appropriate license identifier,
   the file was flagged for further research and to be revisited later
   in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.  The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
 - a full scancode scan run, collecting the matched texts, detected
   license ids and scores
 - reviewing anything where there was a license detected (about 500+
   files) to ensure that the applied SPDX license was correct
 - reviewing anything where there was no detection but the patch license
   was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
   SPDX license was correct

This produced a worksheet with 20 files needing minor correction.  This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg.  Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected.  This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.)  Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-02 11:10:55 +01:00
Carlo Caione
ed80a13bb4 mmc: meson-mx-sdio: Add a driver for the Amlogic Meson8 and Meson8b SoCs
Add a driver for the SDIO/MMC host found on the Amlogic Meson SoCs. This
is an MMC controller which provides an interface between the application
processor and various memory cards. It supports the SD specification
v2.0 and the eMMC specification v4.41.

The controller provides an internal "mux" which allows connecting up to
three MMC devices to it. Only one device can be used at a time though
since the registers are shared across all devices. The driver takes care
of synchronizing access (similar to the dw_mmc driver).
The maximum supported bus-width is 4-bits.

Amlogic's GPL kernel sources call the corresponding driver "aml_sdio" to
differentiate it from the other MMC controller in (at least the Meson8
and Meson8b) the SoCs (they call the other drivers aml_sdhc and
aml_sdhc_m8, which seem to support a bus-width of up to 8-bits). This
means that there are three different MMC host controller IP blocks from
Amlogic (each of them with completely own register layout and features):
- "SDIO": 1 and 4 bit bus width, support for high-speed modes up to
  UHS-I SDR50, part of Meson6, Meson8 and Meson8b (the driver from this
  patch targets this controller)
- "SDHC": 1, 4 and 8 bit bus width, compatible with standard iNAND
  interface, support for speeds up to HS200 and MMC spec up to version
  4.5x, part of Meson8 and Meson8b SoCs (there is no mainline driver
  for this controller yet)
- "SDEMMC": 1, 4 and 8 bit bus width, support for speeds up to HS400
  and MMC spec up to version 5.0, part of the Meson GX (64-bit) SoCs
  (supported by the meson-gx MMC host driver)

Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-10-30 11:46:02 +01:00
Kishon Vijay Abraham I
7d326930d3 mmc: sdhci-omap: Add OMAP SDHCI driver
Create a new sdhci-omap driver to configure the eMMC/SD/SDIO controller
in TI's OMAP SoCs making use of the SDHCI core library. For OMAP specific
configurations, populate sdhci_ops with OMAP specific callbacks and use
SDHCI quirks.
Enable only high speed mode for both SD and eMMC here and add other
UHS mode support later.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-09-22 10:28:49 +02:00
Srinivas Kandagatla
1ac9906622 mmc: mmci: stop building qcom dml as module
It does not make sense for qcom dml code to be a seperate module, as
this has just 2 helper functions specific to qcom, and used directly by
mmci driver, so just compile this along with main mmci driver.

This would also fix issues arrising due to Kconfig combinations between
mmci and qcom dml.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-08-30 15:03:53 +02:00
Simon Horman
2a68ea7896 mmc: renesas-sdhi: add support for R-Car Gen3 SDHI DMAC
Add a new variant of the SDHI driver to support R-Car Gen3 with DMA via
on-chip bus mastering.  Since the DMAC is in a part of the SDHI module it
is not suitable to be used via DMA Engine.

Clearing of DM_CM_INFO1 after DMA thanks to Dirk Behme

Cc: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Ai Kyuse <ai.kyuse.uw@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-08-30 14:01:21 +02:00
Simon Horman
b5b6a5f4f0 mmc: renesas-sdhi: rename sh_mobile_sdhi.c => renesas_sdhi_core.c
Rename the source file SDHI. A follow-up patch will make it a library
file used by a different top-level module file.

The name "renesas" is chosen as the SDHI driver is applicable to a wider
range of SoCs than SH-Mobile it seems to be a more appropriate name.
However, the SDHI driver source itself, is left as sh_mobile_sdhi to
avoid unnecessary churn.

the name "core" was chosen to reflect the desired role of this file,
to provide core functionality to the sdhi driver. A follow-up patch will
move the file into that role.

Internal symbols have also been renamed to reflect the filename change.

The .name member of struct platform_driver and parameter to
MODULE_ALIAS() have not been changed in order to avoid the complication
of potentially breaking SH SoCs which still use platform drivers.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-06-20 10:30:15 +02:00
Simon Horman
c2a96987c7 mmc: renesas-sdhi: rename tmio_mmc_dma.c => renesas_sdhi_sys_dmac.c
Rename the source file for DMA for SDHI as a follow-up to attaching
DMA code to the SDHI driver rather than the tmio_core driver.

The name "renesas" is chosen as the SDHI driver is applicable to a wider
range of SoCs than SH-Mobile it seems to be a more appropriate name.
However, the SDHI driver source itself, is left as sh_mobile_sdhi to
avoid unnecessary churn.

The name sys_dmac was chosen to reflect the type of DMA used.

Internal symbols have also been renamed to reflect the filename change.

A follow-up patch will re-organise the SDHI driver removing
the need for renesas_sdhi_get_dma_ops().

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-06-20 10:30:15 +02:00
Simon Horman
426e95d176 mmc: tmio: rename tmio_mmc_{pio => core}.c
Rename tmio_mmc_pio.c to tmio_mmc_core.c to more accurately reflect its
function: to provide core code for the tmio-mmc and sh-mobole-sdhi drivers.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-06-20 10:30:14 +02:00
Simon Horman
631fa73cfb mmc: renesas-sdhi, tmio: make dma more modular
Refactor DMA support to allow it to be provided by a set of call-backs
that are provided by a host driver. The motivation is to allow multiple
DMA implementations to be provided and instantiated at run-time.

Instantiate the existing DMA implementation from the sh_mobile_sdhi driver
which appears to match the current use-case. This has the side effect
of moving the DMA code from the tmio_core to the sh_mobile_sdhi driver.

A follow-up patch will change the source file for the SDHI DMA
implementation accordingly. Another follow-up patch will re-organise the
SDHI driver removing the need for tmio_mmc_get_dma_ops().

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-06-20 10:30:14 +02:00
Steven J. Hill
01d9584333 mmc: cavium: Add MMC support for Octeon SOCs.
Add platform driver for Octeon SOCs.

Signed-off-by: Steven J. Hill <Steven.Hill@cavium.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-04-24 21:51:20 +02:00
Hu Ziji
06c8b667ff mmc: sdhci-xenon: Add support to PHYs of Marvell Xenon SDHC
Marvell Xenon eMMC/SD/SDIO Host Controller contains PHY.
Multiple types of PHYs are supported.

Add support to multiple types of PHYs init and configuration.
Add register definitions of PHYs.

Xenon PHY cannot fit in kernel common PHY framework.
Xenon SDHC PHY register is a part of Xenon SDHC register set.
Besides, MMC initialization has to call several PHY functions to
complete timing setting.
Those PHY setting functions have to access SDHC registers and know
current MMC setting, such as bus width, clock frequency and
speed mode.
As a result, implement Xenon PHY in MMC host directory.

Signed-off-by: Hu Ziji <huziji@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-04-24 21:42:16 +02:00
Hu Ziji
3a3748dba8 mmc: sdhci-xenon: Add Marvell Xenon SDHC core functionality
Add Xenon eMMC/SD/SDIO host controller core functionality.
Add Xenon specific initialization process.
Add Xenon specific mmc_host_ops APIs.
Add Xenon specific register definitions.

Add CONFIG_MMC_SDHCI_XENON support in drivers/mmc/host/Kconfig.

Marvell Xenon SDHC conforms to SD Physical Layer Specification
Version 3.01 and is designed according to the guidelines provided
in the SD Host Controller Standard Specification Version 3.00.

Signed-off-by: Hu Ziji <huziji@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-04-24 21:42:16 +02:00
Jan Glauber
166bac38c3 mmc: cavium: Add MMC PCI driver for ThunderX SOCs
Add a platform driver for ThunderX ARM SOCs.

Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-04-24 21:42:09 +02:00
Eric Anholt
660fc733bd mmc: bcm2835: Add new driver for the sdhost controller.
The 2835 has two SD controllers: The Arasan sdhci controller (supported
by the iproc driver) and a custom sdhost controller.  This patch adds a
driver for the latter.

The sdhci controller supports both sdcard and sdio.  The sdhost
controller supports the sdcard only, but has better performance.  Also
note that the rpi3 has sdio wifi, so driving the sdcard with the sdhost
controller allows to use the sdhci controller for wifi support.

The configuration is done by devicetree via pin muxing.  Both SD
controller are available on the same pins (2 pin groups = pin 22 to 27 +
pin 48 to 53).  So it's possible to use both SD controllers at the same
time with different pin groups.

The code was originally written by Phil Elwell in the downstream
Rasbperry Pi tree.   In preparation for the upstream merge it was
cleaned up and the code base was moderized by Eric Anholt, Stefan
Wahren and Gerd Hoffmann.

Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-04-24 21:41:25 +02:00
Jun Nie
a8c643ad00 mmc: dw_mmc: zx: Initial support for ZX mmc controller
This platform driver adds initial support for the DW host controller
found on ZTE SoCs.

It has been tested on ZX296718 EVB board currently. More support on
timing tuning will be added when hardware is available.

Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:03 +01:00
Masahiro Yamada
ff6af28faf mmc: sdhci-cadence: add Cadence SD4HC support
Add a driver for the Cadence SD4HC SD/SDIO/eMMC Controller.

For SD, it basically relies on the SDHCI standard code.
For eMMC, this driver provides some callbacks to support the
hardware part that is specific to this IP design.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-08 15:02:52 +01:00
Kevin Hilman
51c5d8447b MMC: meson: initial support for GX platforms
Initial support for the SD/eMMC controller in the Amlogic S905/GX*
family of SoCs.

Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:00:43 +01:00
Al Cooper
476bf3d62d mmc: sdhci-brcmstb: Add driver for Broadcom BRCMSTB SoCs
Add SDHCI driver for Broadcom BRCMSTB SoCs.
This driver works with all ARM based SoCs and the 7425, 7429
and 7435 MIPS based SoCs.

The driver disables all UHS speed modes by default and relies
on the Device Tree node properties to enable these modes for
SoC/Board combinations that support them.

Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-07-25 10:34:14 +02:00
Stefan Wahren
7eb16493ec mmc: sdhci-bcm2835: remove driver
The sdhci-bcm2835 is no more needed since it has been replaced
by sdhci-iproc.

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-07-25 10:34:10 +02:00
Andrei Pistirica
5d9460d74c mmc: sdhci-pic32: Add PIC32 SDHCI host controller driver
This driver supports the SDHCI host controller found on a PIC32.

Signed-off-by: Andrei Pistirica <andrei.pistirica@microchip.com>
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
2016-02-29 11:03:12 +01:00
Ben Hutchings
659c9bc114 mmc: sdhci-pci: Build o2micro support in the same module
sdhci-pci-o2micro.c contains no initialisation and its functions are only
called from shdci-pci.c, so there is no reason for it to be a separate
module, let alone or for it to always be built-in.

- Rename sdhci-pci.c to sdhci-pci-core.c so that the sdhci-pci module
  can be built from multiple source files
- Add sdhci-pci-o2micro.c to it
- Remove redundant exports

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-10-26 16:00:05 +01:00
ludovic.desroches@atmel.com
bb5f8ea4d5 mmc: sdhci-of-at91: introduce driver for the Atmel SDMMC
Introduce driver for he Atmel SDMMC available on sama5d2. It is a sdhci
compliant controller.

Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-08-24 11:25:53 +02:00
Chaotian Jing
208489032b mmc: mediatek: Add Mediatek MMC driver
Add Mediatek MMC driver code
Support eMMC/SD/SDIO

Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-06-18 09:20:48 +02:00
Linus Torvalds
d0440c59f5 ARM: SoC cleanups for v4.1
We've got a fairly large cleanup branch this time. The bulk of this is removal
 of non-DT platforms of several flavors:
 
 - Atmel at91 platforms go full-DT, with removal of remaining board-file based
   support
 - OMAP removes legacy board files for three more platforms
 - Removal of non-DT mach-msm, newer Qualcomm platforms now live in mach-qcom
 - Freescale i.MX25 also removes non-DT platform support
 
 Most of the rest of the changes here are fallout from the above, i.e. for
 example removal of drivers that now lack platforms, etc.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJVNzI3AAoJEIwa5zzehBx3ePwQAJKb4Mf72/4iiKb4dbVcooQN
 EiZ84fwWiWD6Mww/3A76xVnz/b7JWmB3vwW0b4fcbvzubmOjnROBmZgCWeNy4ZTv
 dOZc3/9jK7OrlwvpFBeZykQwHcbz+550+m3WxmLft1oqH/7BA1k5aunwYtFB96ii
 5Owi4Cy9OmxEyALQAvzktFaJdI7J66LNb+i30r5zIZHlkVooeF3UyadndiswUP2o
 EBzCE8UPqRi5kV6FuwVyf4MZaV28FWoglTqdx9OxogcTnKNFT6RlHQ39q/iPu348
 Wkh4kOryVy7Rlab1K4wQRpBoOwkonKDV73u2H2ifRFj7V9ZAdjibK8pgKn3kjkba
 bJkwHIqlqtqqqjj2Hh93wl+8hKSypoLXO9tagPWYBiLtFXCH/+EVsihWYpAc/A5E
 pUS6hJrJyXKJouwwsXu6459zP0ieqhvpbQG72xs9PRimAfAdSTulSTzdI/dMh42Q
 pwYkmvh+ReY3Ll4MeCzu7+eCIY0qAKsor48W1ImuziwQhg2lZj16qWtA4YdPk3+O
 N8ckyaaFg663PAfsZgBx1qTgxw5v0ec2k68/iEVGS5mUJCgcWxFvR95chTDIxQXq
 ZmJ+SuMFyLB/2zVSiGU96L1PQTcUkxJJ8LVB3qNp6KlYT7qUSsgAU+qYveFlUh+p
 X8MVsSVh8n1MTNepsLij
 =BV8A
 -----END PGP SIGNATURE-----

Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC cleanups from Olof Johansson:
 "We've got a fairly large cleanup branch this time.  The bulk of this
  is removal of non-DT platforms of several flavors:

   - Atmel at91 platforms go full-DT, with removal of remaining
     board-file based support

   - OMAP removes legacy board files for three more platforms

   - removal of non-DT mach-msm, newer Qualcomm platforms now live in
     mach-qcom

   - Freescale i.MX25 also removes non-DT platform support"

Most of the rest of the changes here are fallout from the above, i.e. for
example removal of drivers that now lack platforms, etc.

* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (58 commits)
  mmc: Remove msm_sdcc driver
  gpio: Remove gpio-msm-v1 driver
  ARM: Remove mach-msm and associated ARM architecture code
  ARM: shmobile: cpuidle: Remove the pointless default driver
  ARM: davinci: dm646x: Add interrupt resource for McASPs
  ARM: davinci: irqs: Correct McASP1 TX interrupt definition for DM646x
  ARM: davinci: dm646x: Clean up the McASP DMA resources
  ARM: davinci: devices-da8xx: Add support for McASP2 on da830
  ARM: davinci: devices-da8xx: Clean up and correct the McASP device creation
  ARM: davinci: devices-da8xx: Add interrupt resource to McASP structs
  ARM: davinci: devices-da8xx: Add resource name for the McASP DMA request
  ARM: OMAP2+: Remove legacy support for omap3 TouchBook
  ARM: OMAP3: Remove legacy support for devkit8000
  ARM: OMAP3: Remove legacy support for EMA-Tech Stalker board
  ARM: shmobile: Consolidate the pm code for R-Car Gen2
  ARM: shmobile: r8a7791: Correct SYSCIER value
  ARM: shmobile: r8a7790: Correct SYSCIER value
  ARM: at91: remove old setup
  ARM: at91: sama5d4: remove useless map_io
  ARM: at91: sama5 use SoC detection infrastructure
  ...
2015-04-22 09:04:39 -07:00
Stephen Boyd
27842bb18b mmc: Remove msm_sdcc driver
This driver is orphaned now that mach-msm has been removed.
Delete it.

Cc: Chris Ball <chris@printf.net>
Cc: David Brown <davidb@codeaurora.org>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
2015-03-27 11:31:02 -05:00
Scott Branden
b580c52d58 mmc: sdhci-iproc: add IPROC SDHCI driver
Add IPROC SDHCI driver for IPROC family of Broadcom devices.

Acked-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Corneliu Doban <cdoban@broadcom.com>
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-03-23 14:13:41 +01:00
Vincent Yang
87a507459f mmc: sdhci: host: add new f_sdh30
This patch adds new host controller driver for
Fujitsu SDHCI controller f_sdh30.

Signed-off-by: Vincent Yang <Vincent.Yang@tw.fujitsu.com>
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Tetsuya Takinishi <t.takinishi@jp.fujitsu.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-01-20 09:32:37 +01:00