The DMADISABLE bit is a semi-automatic bit present in sysconfig register
of some modules. When the DMA must perform read/write accesses, the
DMADISABLE bit is cleared by the hardware. But when the DMA must stop for power
management, software must set the DMADISABLE bit back to 1.
In cases where the ROMCODE/BOOTLOADER uses dma, the hardware clears the
DMADISABLE bit (but the romcode/bootloader might not set it back to 1).
In order for the kernel to start in a clean state, it is
necessary for the kernel to set DMADISABLE bit back to 1 (irrespective
of whether it's been set to 1 in romcode or bootloader).
During _reset of the (hwmod)device, the DMADISABLE bit is set so that it
does not prevent idling of the system. (NOTE: having DMADISABLE to 0,
prevents the system to idle)
DMADISABLE bit is present in usbotgss module of omap5.
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[paul@pwsan.com: updated to apply; fixed checkpatch warnings]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some prm and cm registers read/write and status functions
are built only for some custom OMAP2+ builds and are stubbed
in header files for other builds under ifdef statements.
But this results in adding new CONFIG_ARCH_OMAPXXX
checks when SOCs are added in the future. So move them
to a common place for OMAP2+ and make them 'weak' implementations.
This way no new ifdefs would be required in the future and also
cleans up the existing code.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
[paul@pwsan.com: unsplit quoted strings; moved PRM functions to
mach-omap2/prm_common.c; resolved sparse warnings]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add an API to get main clock name associated with a given @oh.
This will avoid the need to construct fclk names during early
initialization in order to get fclk handle using clk_get().
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
If the dpll is already locked, code can be optimized
to return much earlier than doing redundent set of lock mode
and wait on idlest.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Jon Hunter <jon-hunter@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Mike Turquette <mturquette@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The register is used to configure the behaviour of the CSI-2 and CCP-2
receivers. This register is available only in OMAP3630.
The original patch was submitted by Vimarsh Zutshi.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Cc: Vimarsh Zutshi <vimarsh.zutshi@gmail.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The wake-up power domain is an alway-on power domain and so this power domain
does not have a power state status (PM_PWSTST_xxx) register that indicates the
current state. However, during the registering of the wake-up power domain the
state of the domain is queried by calling pwrdm_read_pwrst(). This actually
tries to read a register that does not exist and returns a value of 0 that
indicates that the current state is OFF. The OFF state count of the wake-up
power domain is then set to 1 and the current state to OFF. Both of which are
incorrect.
To fix this, if a power domain only supports the ON state, do not attempt to
read the power state status register and simply return ON as the current power
state.
This is based upon Tony's current linux-omap master branch.
Testing:
- Boot tested on OMAP4460 panda.
- Boot tested on OMAP3430 beagle and validated CORE RET still working (using
Paul's 32k timer patch [1]).
[1] http://marc.info/?l=linux-omap&m=134000053229888&w=2
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[paul@pwsan.com: edited commit message slightly]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
For OMAP3+ devices, the clock domains (CLKDMs) support one or more of the
following transition modes ...
NO_SLEEP (0x0) - A clock domain sleep transition is never initiated,
irrespective of the hardware conditions.
SW_SLEEP (0x1) - A software-forced sleep transition. The transition is initiated
when the associated hardware conditions are satisfied
SW_WKUP (0x2) - A software-forced clock domain wake-up transition is initiated,
irrespective of the hardware conditions.
HW_AUTO (0x3) - Hardware-controlled automatic sleep and wake-up transition is
initiated by the PRCM module when the associated hardware
conditions are satisfied.
For OMAP4 devices, SW_SLEEP is equivalent to HW_AUTO and NO_SLEEP is equivalent
to SW_WKUP. The only difference between HW_AUTO and SW_SLEEP for OMAP4 devices
is that the PRM_IRQSTATUS_MPU.TRANSITION_ST interrupt status is set in case of
SW_SLEEP transition, and not set in case of HW_AUTO transition.
For OMAP4 devices, all CLKDMs support HW_AUTO and therefore we can place the
CLKDMs in the HW_AUTO state instead of the SW_SLEEP mode. Hence, we do not
need to use the SW_SLEEP mode. With regard to NO_SLEEP and SW_WKUP it is
preferred to use SW_WKUP mode if the CLKDM supports it and so use this mode
instead of NO_SLEEP where possible.
For a software perspective the above 4 modes are represented by the following
flags to indicate what modes are supported by each of the CLKDMs.
CLKDM_CAN_DISABLE_AUTO --> NO_SLEEP
CLKDM_CAN_ENABLE_AUTO --> HW_AUTO
CLKDM_CAN_FORCE_SLEEP --> SW_SLEEP
CLKDM_CAN_FORCE_WAKEUP --> SW_WKUP
By eliminating the SW_SLEEP mode the the mapping of the flags for OMAP4 devices
can becomes ...
CLKDM_CAN_DISABLE_AUTO --> NO_SLEEP
CLKDM_CAN_ENABLE_AUTO --> HW_AUTO
CLKDM_CAN_FORCE_SLEEP --> HW_AUTO
CLKDM_CAN_FORCE_WAKEUP --> SW_WKUP
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Reviewed-by: Benoit Cousson <b-cousson@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
In case of AM33XX device, XXX_RSTST register offset is not
consistent across PRM modules/instances,
PRM_XXX RSTST
=========================
PRM_PER_MOD: 0x04
PRM_WKUP_MOD: 0x0C
PRM_MPU_MOD: NA
PRM_DEVICE_MOD: 0x08
This means, we need to pass on XXX_RSTST register offset
information through omap_hwmod data, similar to XXX_RSTCTRL.
Currently, this field is only applicable and used for AM33XX
devices.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
In case of AM33xx family of devices (like cpsw) have different sysc
bit field offsets defined,
sysc_type3:
| 3 2 | 1 0 |
| STDBYMODE | IDLEMODE |
So introduce new sysc_type3 in omap_hwmod common data.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Another week, another batch of fixes.
All are small, contained, targeted fixes for explicit problems -- mostly
build and boot failures across i.MX, OMAP, Renesas/Shmobile and Samsung.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=C8+9
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another week, another batch of fixes.
All are small, contained, targeted fixes for explicit problems --
mostly build and boot failures across i.MX, OMAP, Renesas/Shmobile and
Samsung."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: imx6q: fix suspend regression caused by common clk migration
ARM: OMAP4470: Fix OMAP4470 boot failure
ARM: EXYNOS: Fix EXYNOS_DEV_DMA Kconfig entry
ARM: OMAP2+: nand: fix build error when CONFIG_MTD_ONENAND_OMAP2=n
ARM: shmobile: r8a7779: Route all interrupts to ARM
ARM: shmobile: kzm9d: use late init machine hook
ARM: shmobile: kzm9g: use late init machine hook
ARM: mach-shmobile: armadillo800eva: Use late init machine hook
ARM: SAMSUNG: Fix for S3C2412 EBI memory mapping
ARM: mach-shmobile: add missing GPIO IRQ configuration on mackerel
ARM: mach-shmobile: Fix build when SMP is enabled and EMEV2 is not enabled
ARM: shmobile: sh7372: bugfix: chclr_offset base
ARM: shmobile: sh73a0: bugfix: SY-DMAC number
ARM: SAMSUNG: Should check for IS_ERR(clk) instead of NULL
When moving to common clk framework, the imx6q clks rom and mmdc_ch1_axi
get different on/off states than old clk driver, which breaks suspend
function. There might be a better way to manage these clocks, but let's
takes the old clk driver approach to fix the regression first.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
trivial fix to get omap4470 booting.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=EieC
-----END PGP SIGNATURE-----
Merge tag 'omap-fixes-for-v3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
"Here's one more regression fix that I missed earlier, and a
trivial fix to get omap4470 booting."
* tag 'omap-fixes-for-v3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP4470: Fix OMAP4470 boot failure
ARM: OMAP2+: nand: fix build error when CONFIG_MTD_ONENAND_OMAP2=n
OMAP4470 currently fails to boot, printing various messages such as ...
omap_hwmod: mpu: cannot clk_get main_clk dpll_mpu_m2_ck
omap_hwmod: mpu: cannot _init_clocks
------------[ cut here ]------------
WARNING: at arch/arm/mach-omap2/omap_hwmod.c:2062 _init+0x2a0/0x2e4()
omap_hwmod: mpu: couldn't init clocks
Modules linked in:
[<c001c7fc>] (unwind_backtrace+0x0/0xf4) from [<c0043c64>] (warn_slowpath_common+0x4c/0x64)
[<c0043c64>] (warn_slowpath_common+0x4c/0x64) from [<c0043d10>] (warn_slowpath_fmt+0x30/0x40)
[<c0043d10>] (warn_slowpath_fmt+0x30/0x40) from [<c0674208>] (_init+0x2a0/0x2e4)
[<c0674208>] (_init+0x2a0/0x2e4) from [<c067428c>] (omap_hwmod_setup_one+0x40/0x60)
[<c067428c>] (omap_hwmod_setup_one+0x40/0x60) from [<c0674280>] (omap_hwmod_setup_one+0x34/0x60)
[<c0674280>] (omap_hwmod_setup_one+0x34/0x60) from [<c06726f4>] (omap_dm_timer_init_one+0x30/0x250)
[<c06726f4>] (omap_dm_timer_init_one+0x30/0x250) from [<c0672930>] (omap2_gp_clockevent_init+0x1c/0x108)
[<c0672930>] (omap2_gp_clockevent_init+0x1c/0x108) from [<c0672c60>] (omap4_timer_init+0x10/0x5c)
[<c0672c60>] (omap4_timer_init+0x10/0x5c) from [<c066c418>] (time_init+0x20/0x30)
[<c066c418>] (time_init+0x20/0x30) from [<c0668814>] (start_kernel+0x1b0/0x304)
[<c0668814>] (start_kernel+0x1b0/0x304) from [<80008044>] (0x80008044)
---[ end trace 1b75b31a2719ed1c ]---
The problem is that currently none of the clocks are being registered for
OMAP4470 devices and so on boot-up no clocks can be found and the kernel panics.
This fix allows the kernel to boot without failure using a simple RAMDISK file
system on OMAP4470 blaze board.
Per feedback from Paul and Benoit the 4470 clock data is incomplete for new
modules such as the 2D graphics block that has been added to the 4470.
Therefore add a warning to indicate that the clock data is incomplete.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 20ef9e08 ("ARM: EXYNOS: Support DMA for EXYNOS5250 SoC")
renamed EXYNOS4_DEV_DMA to EXYNOS_DEV_DMA. But some machine entries
still had EXYNOS4_DEV_DMA. Changed them to EXYNOS_DEV_DMA.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
commit 8259573b (ARM: OMAP2+: nand: Make board_onenand_init() visible
to board code) broke the build for configs with OneNAND disabled. By
removing the static in the header file, it created a duplicate definition
in the .c and the .h files, resuling in a build error:
/work/kernel/omap/dev/arch/arm/mach-omap2/board-flash.c:102:111: error: redefinition of 'board_onenand_init'
/work/kernel/omap/dev/arch/arm/mach-omap2/board-flash.h:56:51: note: previous definition of 'board_onenand_init' was here
make[2]: *** [arch/arm/mach-omap2/board-flash.o] Error 1
make[2]: *** Waiting for unfinished jobs....
make[1]: *** [arch/arm/mach-omap2] Error 2
make: *** [sub-make] Error 2
Fix this by removing the duplicate dummy entry from the C file.
Cc: Enric Balletbò i Serra <eballetbo@gmail.com>
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull media fixes from Mauro Carvalho Chehab.
Trivial conflict due to new USB HID ID's being added next to each other
(Baanto vs Axentia).
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (44 commits)
[media] smia: Fix compile failures
[media] Fix VIDIOC_DQEVENT docbook entry
[media] s5p-fimc: Fix control creation function
[media] s5p-mfc: Fix checkpatch error in s5p_mfc_shm.h file
[media] s5p-mfc: Fix setting controls
[media] v4l/s5p-mfc: added image size align in VIDIOC_TRY_FMT
[media] v4l/s5p-mfc: corrected encoder v4l control definitions
[media] v4l: mem2mem_testdev: Fix race conditions in driver
[media] s5p-mfc: Bug fix of timestamp/timecode copy mechanism
[media] cxd2820r: Fix an incorrect modulation type bitmask
[media] em28xx: Show a warning if the board does not support remote controls
[media] em28xx: Add remote control support for Terratec's Cinergy HTC Stick HD
[media] USB: Staging: media: lirc: initialize spinlocks before usage
[media] Revert "[media] media: mx2_camera: Fix mbus format handling"
[media] bw-qcam: driver and pixfmt documentation fixes
[media] cx88: fix firmware load on big-endian systems
[media] cx18: support big-endian systems
[media] ivtv: fix support for big-endian systems
[media] tuner-core: return the frequency range of the correct tuner
[media] v4l2-dev.c: fix g_parm regression in determine_valid_ioctls()
...
IOMMU-aware dma_alloc_attrs() implementation allocates buffers in
power-of-two chunks to improve performance and take advantage of large
page mappings provided by some IOMMU hardware. However current code, due
to a subtle bug, allocated those chunks in the smallest-to-largest
order, what completely killed all the advantages of using larger than
page chunks. If a 4KiB chunk has been mapped as a first chunk, the
consecutive chunks are not aligned correctly to the power-of-two which
match their size and IOMMU drivers were not able to use internal
mappings of size other than the 4KiB (largest common denominator of
alignment and chunk size).
This patch fixes this issue by changing to the correct largest-to-smallest
chunk size allocation sequence.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/renesas:
ARM: shmobile: r8a7779: Route all interrupts to ARM
ARM: shmobile: kzm9d: use late init machine hook
ARM: shmobile: kzm9g: use late init machine hook
ARM: mach-shmobile: armadillo800eva: Use late init machine hook
ARM: mach-shmobile: add missing GPIO IRQ configuration on mackerel
ARM: mach-shmobile: Fix build when SMP is enabled and EMEV2 is not enabled
ARM: shmobile: sh7372: bugfix: chclr_offset base
ARM: shmobile: sh73a0: bugfix: SY-DMAC number
Nothing very controversial in here. Most of the fixes are for OMAP this time
around, with some orion/kirkwood and a tegra patch mixed in.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=6Ahb
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Nothing very controversial in here. Most of the fixes are for OMAP
this time around, with some orion/kirkwood and a tegra patch mixed in."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: Orion: Fix Virtual/Physical mixup with watchdog
ARM: Kirkwood: clk_register_gate_fn: add fn assignment
ARM: Orion5x - Restore parts of io.h, with rework
ARM: OMAP4: hwmod data: Force HDMI in no-idle while enabled
ARM: OMAP2+: mux: fix sparse warning
ARM: OMAP2+: CM: increase the module disable timeout
ARM: OMAP4: clock data: add clockdomains for clocks used as main clocks
ARM: OMAP4: hwmod data: fix 32k sync timer idle modes
ARM: OMAP4+: hwmod: fix issue causing IPs not going back to Smart-Standby
ARM: OMAP: Fix Beagleboard DVI reset gpio
arm/dts: OMAP2: Fix interrupt controller binding
ARM: OMAP2: Fix tusb6010 GPIO interrupt for n8x0
ARM: OMAP2+: Fix MUSB ifdefs for platform init code
ARM: tegra: make tegra_cpu_reset_handler_enable() __init
ARM: OMAP: PM: Lock clocks list while generating summary
ARM: iconnect: Remove include of removed linux/spi/orion_spi.h
The orion watchdog is expecting to be passed the physcial address of
the hardware, and will ioremap() it to give a virtual address it will
use as the base address for the hardware. However, when creating the
platform resource record, a virtual address was being used.
Add the necassary #define's so we can pass the physical address as
expected.
Tested on Kirkwood and Orion5x.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Olof Johansson <olof@lixom.net>
In commit:
98d9986 ARM: Kirkwood: Replace clock gating
the kirkwood clock gating has been reworked. A custom variant of
clock gating, that calls a custom function before gating the clock
off, has been introduced. However in clk_register_gate_fn() this
custom function "fn" is never assigned.
This patch adds the missing fn assignment.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@blackshift.org>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit 4d5fc58dbe (ARM: remove bunch of
now unused mach/io.h files) removed the orion5x io.h. Unfortunately,
this is still needed for the definition of IO_SPACE_LIMIT which
overrides the default 64K. All Orion based systems have 1Mbyte of IO
space per PCI[e] bus, and try to request_resource() this size. Orion5x
has two such PCI buses.
It is likely that the original, removed version, was broken. This
version might be less broken. However, it has not been tested on
hardware with a PCI card, let alone hardware with a PCI card with IO
capabilities.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
reset. All of them are regression fixes, except for the missing omap2
interrupt controller binding that somehow got missed earlier.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=cMPJ
-----END PGP SIGNATURE-----
Merge tag 'omap-fixes-for-v3.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
"Here are a few fixes with the biggest one being fix for Beagle DVI
reset. All of them are regression fixes, except for the missing omap2
interrupt controller binding that somehow got missed earlier."
* tag 'omap-fixes-for-v3.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: Fix Beagleboard DVI reset gpio
arm/dts: OMAP2: Fix interrupt controller binding
ARM: OMAP2: Fix tusb6010 GPIO interrupt for n8x0
ARM: OMAP2+: Fix MUSB ifdefs for platform init code
Without this, the interrupts for I2C, VIN, GPIO, SDHC, HSCIF and
HPB-DMAC are sent to the SH processor.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
As per the OMAP4 documentation, audio over HDMI must be transmitted in
no-idle mode. This patch adds the HWMOD_SWSUP_SIDLE so that omap_hwmod uses
no-idle/force-idle settings instead of smart-idle mode.
This is required as the DSS interface clock is used as functional clock
for the HDMI wrapper audio FIFO. If no-idle mode is not used, audio could
be choppy, have bad quality or not be audible at all.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
[b-cousson@ti.com: Update the subject and align the .flags
location with the script template]
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit bbd707acee ("ARM: omap2: use
machine specific hook for late init") resulted in the addition of this
sparse warning:
arch/arm/mach-omap2/mux.c:791:12: warning: symbol 'omap_mux_late_init' was not declared. Should it be static?
Fix by including the header file containing the prototype.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Tony Lindgren <tony@atomide.com>
Increase the timeout for disabling an IP block to five milliseconds.
This is to handle the usb_host_fs idle latency, which takes almost
four milliseconds after a host controller reset.
This is the second of two patches needed to resolve the following
boot warning:
omap_hwmod: usb_host_fs: _wait_target_disable failed
Thanks to Sergei Shtylyov <sshtylyov@mvista.com> for finding
an unrelated hunk in a previous version of this patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: Tero Kristo <t-kristo@ti.com>
Until the OMAP4 code is converted to disable the use of the clock
framework-based clockdomain enable/disable sequence, any clock used as
a hwmod main_clk must have a clockdomain associated with it. This
patch populates some clock structure clockdomain names to resolve the
following warnings during kernel init:
omap_hwmod: dpll_mpu_m2_ck: missing clockdomain for dpll_mpu_m2_ck.
omap_hwmod: trace_clk_div_ck: missing clockdomain for trace_clk_div_ck.
omap_hwmod: l3_div_ck: missing clockdomain for l3_div_ck.
omap_hwmod: ddrphy_ck: missing clockdomain for ddrphy_ck.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
The 32k sync timer IP block target idle modes in the hwmod data are
incorrect. The IP block does not support any smart-idle modes.
Update the data to reflect the correct modes.
This problem was initially identified and a diff fragment posted to
the lists by Benoît Cousson <b-cousson@ti.com>. A patch description
bug in the first version was also identified by Benoît.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
If an IP is configured in Smart-Standby-Wakeup, when disabling wakeup feature the
IP will not go back to Smart-Standby, but will remain in Smart-Standby-Wakeup.
Signed-off-by: Djamil Elaidi <d-elaidi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Since commit 21cc1b7ede ("ARM: shmobile:
use machine specific hook for late init") suspend and CPU idle are not
initialized automatically anymore. Set shmobile_init_late() as the
machine late init hook to initialize them.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Since commit 21cc1b7ede ("ARM: shmobile:
use machine specific hook for late init") suspend and CPU idle are not
initialized automatically anymore. Set shmobile_init_late() as the
machine late init hook to initialize them.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Since commit 21cc1b7ede ("ARM: shmobile:
use machine specific hook for late init") suspend and CPU idle are not
initialized automatically anymore. Set shmobile_init_late() as the
machine late init hook to initialize them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Here are 3 patches resolving a boot regression (the mop500 fix), a build
warning fix, and a kernel-doc fix. All tiny, but should go into the
final 3.5 release.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk/iNosACgkQMUfUDdst+ykedgCeLhpFrq5dI19tbhEmCroFs4sx
f+4An29dz2bGkjeViDNkmaBC7msPzLNc
=EBge
-----END PGP SIGNATURE-----
Merge tag 'tty-3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull serial driver fixes from Greg Kroah-Hartman:
"Here are 3 patches resolving a boot regression (the mop500 fix), a
build warning fix, and a kernel-doc fix. All tiny, but should go into
the final 3.5 release.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'tty-3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial/amba-pl011: move custom pin control to driver
serial: fix serial_txx9.c build warning/typo
serial: fix kernel-doc warnings in 8250.c
* emailed from Andrew Morton <akpm@linux-foundation.org>: (21 patches)
mm/memblock: fix overlapping allocation when doubling reserved array
c/r: prctl: Move PR_GET_TID_ADDRESS to a proper place
pidns: find_new_reaper() can no longer switch to init_pid_ns.child_reaper
pidns: guarantee that the pidns init will be the last pidns process reaped
fault-inject: avoid call to random32() if fault injection is disabled
Viresh has moved
get_maintainer: Fix --help warning
mm/memory.c: fix kernel-doc warnings
mm: fix kernel-doc warnings
mm: correctly synchronize rss-counters at exit/exec
mm, thp: print useful information when mmap_sem is unlocked in zap_pmd_range
h8300: use the declarations provided by <asm/sections.h>
h8300: fix use of extinct _sbss and _ebss
xtensa: use the declarations provided by <asm/sections.h>
xtensa: use "test -e" instead of bashism "test -a"
xtensa: replace xtensa-specific _f{data,text} by _s{data,text}
memcg: fix use_hierarchy css_is_ancestor oops regression
mm, oom: fix and cleanup oom score calculations
nilfs2: ensure proper cache clearing for gc-inodes
thp: avoid atomic64_read in pmd_read_atomic for 32bit PAE
...
viresh.kumar@st.com email-id doesn't exist anymore as I have left the
company. Replace ST's id with viresh.linux@gmail.com.
It also updates .mailmap file to fix address for 'git shortlog'
Signed-off-by: Viresh Kumar <viresh.linux@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While upgrading the kernel on a S3C2412 based board I've noted
that it was impossible to boot the board with a 2.6.32 or upper
kernel. I've tracked down the problem to the EBI virtual memory
mapping that is in conflict with the IO mapping definition in
arch/arm/mach-s3c24xx/s3c2412.c.
Signed-off-by: Jose Miguel Goncalves <jose.goncalves@inov.pt>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Pull ARM fixes from Russell King:
"This includes three MMCI changes - one to fix up the wrong version of
the DT support patch which was merged, and two to make deferred
probing work. It also includes a fix to the OMAP SPI driver which is
causing a boot time warning.
The remainder are very minor ARM fixes."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
SPI: fix over-eager devm_xxx() conversion
ARM: 7427/1: mmc: mmci: Defer probe() in case of yet uninitialized GPIOs
ARM: 7426/1: mmc: mmci: Remove wrong error handling of gpio 0
ARM: 7425/1: extable: ensure fixup entries are 4-byte aligned
ARM: 7421/1: bpf_jit: BPF_S_ANC_ALU_XOR_X support
ARM: 7423/1: kprobes: run t32_simulate_ldr_literal() without insn slot
ARM: 7422/1: mmc: mmci: Allocate platform memory during Device Tree boot
Commit e813a55eb9 ("OMAP: board-files:
remove custom PD GPIO handling for DVI output") moved TFP410 chip's
powerdown-gpio handling from the board files to the tfp410 driver. One
gpio_request_one(powerdown-gpio, ...) was mistakenly left unremoved in
the Beagle board file. This causes the tfp410 driver to fail to request
the gpio on Beagle, causing the driver to fail and thus the DVI output
doesn't work.
This patch removes several boot errors from board-omap3beagle.c:
- gpio_request: gpio--22 (DVI reset) status -22
- Unable to get DVI reset GPIO
There is a combination of leftover code and revision confusion.
Additionally, xM support is currently a hack.
For original Beagleboard this removes the double initialization of GPIO
170, properly configures it as an output, and wraps the initialization
in an if block so that xM does not attempt to request it.
For Beagleboard xM it removes reference to GPIO 129 which was part
of rev A1 and A2 designs, but never functioned. It then properly assigns
beagle_dvi_device.reset_gpio in beagle_twl_gpio_setup and removes the
hack of initializing it high. Additionally, it uses
gpio_set_value_cansleep since this GPIO is connected through i2c.
Unfortunately, there is no way to tell the difference between xM A2 and
A3. However, GPIO 129 does not function on rev A1 and A2, and the TWL
GPIO used on A3 and beyond is not used on rev A1 and A2, there are no
problems created by this fix.
Tested on Beagleboard-xM Rev C1 and Beagleboard Rev B4.
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When booting with device-tree on an OMAP2420H4, the kernel is hanging when
initialising the interrupts and following kernel dumps is seen ...
[ 0.000000] ------------[ cut here ]------------
[ 0.000000] WARNING: at arch/arm/mach-omap2/irq.c:271 omap_intc_of_init+0x50/0xb4()
[ 0.000000] unable to get intc registers
[ 0.000000] Modules linked in:
[ 0.000000] [<c001befc>] (unwind_backtrace+0x0/0xf4) from [<c0040c34>] (warn_slowpath_common+0x4c/0x64)
[ 0.000000] [<c0040c34>] (warn_slowpath_common+0x4c/0x64) from [<c0040ce0>] (warn_slowpath_fmt+0x30/0x40)
[ 0.000000] [<c0040ce0>] (warn_slowpath_fmt+0x30/0x40) from [<c066b8a4>] (omap_intc_of_init+0x50/0xb4)
[ 0.000000] [<c066b8a4>] (omap_intc_of_init+0x50/0xb4) from [<c0688b70>] (of_irq_init+0x144/0x288)
[ 0.000000] [<c0688b70>] (of_irq_init+0x144/0x288) from [<c0663294>] (init_IRQ+0x14/0x1c)
[ 0.000000] [<c0663294>] (init_IRQ+0x14/0x1c) from [<c06607fc>] (start_kernel+0x198/0x304)
[ 0.000000] [<c06607fc>] (start_kernel+0x198/0x304) from [<80008044>] (0x80008044)
[ 0.000000] ---[ end trace 1b75b31a2719ed1c ]---
[ 0.000000] of_irq_init: children remain, but no parents
The OMAP2 interrupt controller binding is missing the number of interrupts and
interrupt controller register address. Adding these fixes the problem.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Here's one more gpio_to_irq conversion that we missed
earlier. Tested with n800 in gadget mode using USB_ETH.
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 62285963 (usb: musb: drop a gigantic amount of ifdeferry)
got rid of a bunch of ifdefs in the MUSB code. Looks like the
platform init code is still using these dropped defines though,
which in many cases results the board defaulting always to host
mode.
Currently the situation is that USB_MUSB_HDRC is the main
Kconfig option with additional USB_GADGET_MUSB_HDRC so only
these two should be used to select between host and OTG mode.
Fix the situation for omaps. The following users should fix the
platform init code in a similar way:
Dropped Kconfig option Current users
USB_MUSB_OTG blackfin, davinci, not in Kconfigs
USB_MUSB_PERIPHERAL davinci, not in Kconfigs
USB_MUSB_HOST davinci, not in Kconfigs
USB_MUSB_HDRC_HCD blackfin, not in Kconfigs
USB_MUSB_OTG blackfin, not in Kconfigs
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: linux-usb@vger.kernel.org
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
SDHI0 card-detect GPIO IRQ on mackarel currently works, because it is the
default configuration of IRQ26. However, we should not rely on this and
should configure the function explicitly.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Build failed, when SMP is enabled and EMEV2 is not enabled.
arch/arm/mach-shmobile/built-in.o: In function `shmobile_platform_cpu_kill':
/home/iwamatsu/work/kernel/sh-2.6-devel/arch/arm/mach-shmobile/platsmp.c:62: undefined reference to `emev2_platform_cpu_kill'
arch/arm/mach-shmobile/built-in.o: In function `shmobile_smp_get_core_count':
/home/iwamatsu/work/kernel/sh-2.6-devel/arch/arm/mach-shmobile/platsmp.c:39: undefined reference to `emev2_get_core_count'
arch/arm/mach-shmobile/built-in.o: In function `shmobile_smp_prepare_cpus':
/home/iwamatsu/work/kernel/sh-2.6-devel/arch/arm/mach-shmobile/platsmp.c:53: undefined reference to `emev2_smp_prepare_cpus'
arch/arm/mach-shmobile/built-in.o: In function `platform_secondary_init':
/home/iwamatsu/work/kernel/sh-2.6-devel/arch/arm/mach-shmobile/platsmp.c:78: undefined reference to `emev2_secondary_init'
arch/arm/mach-shmobile/built-in.o: In function `boot_secondary':
/home/iwamatsu/work/kernel/sh-2.6-devel/arch/arm/mach-shmobile/platsmp.c:90: undefined reference to `emev2_boot_secondary
This is the cause by when EMEV2 is disabled, that the check by OF of EMEV2 is
performed in platsmp.c.
This patch revise what the function about EMEV2 may not be used in this file,
when EMEV2 is not enabled.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Acked-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
chclr_write() will use (chan_reg + chclr_offset).
In sh7372 case, DMA1CHCLR is started from 0xfe008220,
and chan_reg is started from 0xfe008020 (= sh7372_dmae0_resources).
Thus, chclr_offset should be (0x220 - 0x20) instead of 0x220.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
681e1b3eeb
(ARM: mach-shmobile: sh73a0 DMA Engine support for SY-DMAC)
adds SY-DMAC, but it is 218, not 318
This patch is based on v2.0 manual
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
