A scan request is split into multiple scan commands queued in
scan_pending_q. Each scan command will be sent to firmware and
its response is handlded one after another.
If any error is detected while parsing IE in command response
buffer the remaining data will be ignored and error is returned.
We should check if there is any more scan commands pending in
the queue before returning error. This ensures that we will call
cfg80211_scan_done if this is the last scan command, or send
next scan command in scan_pending_q to firmware.
Cc: "3.6+" <stable@vger.kernel.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In routine _rtl_rx_pre_process(), skb_dequeue() is called to get an skb;
however, the wrong variable name is used in subsequent calls.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This issue was reported on the wireless list (see [1]) in which
brcmsmac ran into a fatal error:
[ 588.284074] brcmsmac bcma0:0: frameid != txh->TxFrameID
[ 588.284098] brcmsmac bcma0:0: MI_TFS: fatal
[ 588.284103] brcmsmac bcma0:0: wl0: fatal error, reinitializing
[ 588.286208] ieee80211 phy0: Hardware restart was requested
The tx status feedback is processed in a loop limiting the number of
frames processed in one run. The code terminate processing when the
limit is reached regardless the txstatus value read from the device
register. When that status is is flagged as being valid it must be
processed as the hardware will clear it after is has been read.
Bisecting was done by Seth Forshee and showed following commit as the
culprit:
commit 57fe504817
Author: Piotr Haber <phaber@broadcom.com>
Date: Wed Nov 28 21:44:07 2012 +0100
brcmsmac: fix bounds checking in tx/rx
[1] http://www.spinics.net/lists/linux-wireless/msg101293.html
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit f590dcec94
which has been reported to cause issues.
See https://lkml.org/lkml/2013/1/20/4 for further details.
Cc: stable@vger.kernel.org [3.7]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add missing "!" as we are supposed to check "!card->adapter"
in PCIe suspend handler.
Cc: "3.2+" <stable@vger.kernel.org>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Reviewed-by: Sergey V. <sftp.mtuci@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Chain swapping should only be enabled when the EEPROM chainmask is set to 5,
regardless of what the runtime chainmask is.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The kbuild test robot reports the following warning with x86_64-randconfig-x955:
warning: (RTL8192CE && RTL8192SE && RTL8192DE && RTL8723AE && RTL8192CU) selects
RTLWIFI which has unmet direct dependencies (NETDEVICES && WLAN &&
(RTL8192CE || RTL8192CU || RTL8192SE || RTL8192DE))
This warning was introduced in commit a290593, "rtlwifi: Modify files for addition
of rtl8723ae", and is d ue to a missing dependence of RTLWIFI on RTL8723AE.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: kbuild test robot <fengguang.wu@intel.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do not correctly change interface type when switching from
IBSS mode to STA mode, that results in microcode errors.
Resolves:
https://bugzilla.redhat.com/show_bug.cgi?id=886946
Reported-by: Jaroslav Skarvada <jskarvad@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rate scaling won't treat the information in a frame
with IEEE80211_TX_CTL_AMPDU set if IEEE80211_TX_STAT_AMPDU
is cleared. But all the frames coming from an AGG tx queue
have IEEE80211_TX_CTL_AMPDU set, and IEEE80211_TX_STAT_AMPDU
is set only if the frame was sent in an AMPDU.
This means that all the data in frames in AGG tx queues that
aren't sent as an AMPDU is thrown away.
This is even more harmful when in bad link conditions, the
frames are sent in an AMPDU and then finally sent as single
frame. So a lot of failures weren't reported and the rate
scaling got stuck in high rates leading to very poor
connectivity.
Fix that by clearing IEEE80211_TX_CTL_AMPDU when the frame
isn't part of an AMPDU.
This bug was introduced by
2eb81a40aa
iwlwifi: don't clear CTL_AMPDU on frame status
This fix basically reverts the aforementioned commit.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes a reported CPU soft lockup where the tasklet tries to acquire the
lock and blocks while ath_prepare_reset (holding the lock) waits for it
to complete.
Cc: stable@vger.kernel.org
Reported-by: Robert Shade <robert.shade@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: fix rx flush handling" added a deadlock that happens
because ath_rx_tasklet is called in a section that has already taken the
rx buffer lock.
It seems that the only purpose of the rxbuflock was a band-aid fix to the
reset vs rx tasklet race, which has been properly fixed in the commit
"ath9k: add a better fix for the rx tasklet vs rx flush race".
Now that the fix is in, we can safely remove the lock to avoid such issues.
Cc: stable@vger.kernel.org
Reported-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On hardware reintialization reference count of
already existing timers would be increased again.
This leads to problems on module unloading.
Cc: stable@vger.kernel.org
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Right now the rx flush is not doing anything useful on AR9003+, as it only
works if the buffers in the rx FIFO have not been purged yet, as is done
by ath_stoprecv.
To fix this, always call ath_flushrecv from within ath_stoprecv before
the FIFO is emptied, but still after the hw receive path has been stopped.
This ensures that frames received (and ACKed by the hardware) shortly before
a reset will be seen by the software, which should improve A-MPDU session
stability.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ensure that the rx tasklet is no longer running when entering the reset path.
Also remove the distinction between flush and no-flush frame processing.
If a frame has been received and ACKed by the hardware, the stack needs to see
it, so that the BA receive window does not go out of sync.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During teardown, mac80211 will not return a new beacon. This is normal and
handled properly in the driver, so there's no need to spam the user with a kernel
warning here.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the next beacon is sent, the ath_buf from the previous run is reused.
If getting a new beacon from mac80211 fails, bf->bf_mpdu is not reset, yet
the skb is freed, leading to a double-free on the next beacon tx attempt,
resulting in a system crash.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On AR9300 the rx FIFO needs to be empty during reset to ensure that no
further DMA activity is generated, otherwise it might lead to memory
corruption issues.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SKBs that are allocated in the HTC layer do not have callbacks
registered and hence ended up not being freed, Fix this by freeing
them properly in the TX completion routine.
Cc: <stable@vger.kernel.org>
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BAND_G is implicit when BAND_GN is present.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently "adapter->config_bands" is updated during infra
association only if channel is provided by user in "iw connect"
command. config_bands is used while preparing association
request to calculate supported rates by intersecting our rates
with the rates advertised by AP.
There is corner case in which we include zero rates in
supported rates TLV based on previous IBSS network history,
which leads to association failure.
This patch fixes the problem by correctly updating config_bands.
Cc: "3.7.y" <stable@vger.kernel.org>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Recent versions of udev cause synchronous firmware loading from the
probe routine to fail because the request to user space would time
out. The original fix for b43 (commit 6b6fa58) moved the firmware
load from the probe routine to a work queue, but it still used synchronous
firmware loading. This method is OK when b43 is built as a module;
however, it fails when the driver is compiled into the kernel.
This version changes the code to load the initial firmware file
using request_firmware_nowait(). A completion event is used to
hold the work queue until that file is available. This driver
reads several firmware files - the remainder can be read synchronously.
On some test systems, the async read fails; however, a following synch
read works, thus the async failure falls through to the sync try.
Reported-and-Tested by: Felix Janda <felix.janda@posteo.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> (V3.4+)
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The fields must be null-terminated, or simple_strtoul will cause issue.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not dereference p->station_id after kfree(cmd) because p
points into the cmd data structure.
Signed-off-by: Nickolai Zeldovich <nickolai@csail.mit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Julian Wollrath <jwollrath@web.de>
Acked-by: Larry Finger <Larry.finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds support for the 60 GHz 802.11ad Wilocity card
through a new driver, wil6210. Wilocity implemented the
firmware, QCA maintains the device driver.
Currently supported:
- STA: with security
- AP: limited to 1 connected STA, security disabled
- Monitor: due to a hardware/firmware limitation
either control or non-control frames are monitored
Using a STA and AP with this drive, one can assemble
a fully functional BSS. Throughput of 1.2Gbps is achieved
with iperf.
The wil6210 cards have on-board flash memory for the
firmware, the cards comes pre-flashed and no firmware
download is required.
For more details see:
http://wireless.kernel.org/en/users/Drivers/wil6210
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wait_event_interruptible function returns -ERESTARTSYS if it's
interrupted by a signal. Driver should check the return value
and handle this case properly.
In mwifiex_wait_queue_complete() routine, as we are now checking
wait_event_interruptible return value, the condition check is not
required. Also, we have removed mwifiex_cancel_pending_ioctl()
call to avoid a chance of sending second command to FW by other path
as soon as we clear current command node. FW can not handle two
commands simultaneously.
Cc: "3.6+" <stable@vger.kernel.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ath9k consists of 2 different sub-modules: ATH9K and ATH9K_HTC.
Both uses common Atheros code from ath.ko and need ATH_COMMON.
However, while ATH9K selects ATH_COMMON, ATH9K_HTC does not.
As result, if ATH9K_HTC is the only Atheros card selected, compilation fails with
unresolved symbols.
This patch moves ATH_COMMON selection to the common part for both
ATH9K and ATH9K_HTC
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's a bug in the currently released firmware version,
the sequence control in the Tx response isn't updated in
all cases. Take it from the packet as a workaround.
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
By accident, commit eb6476441b
("iwlwifi: protect use_ict with irq_lock") changed the return
value of the iwl_pcie_isr() function in case it handles an
interrupt -- it now returns IRQ_NONE instead of IRQ_HANDLED.
Put back the correct return value.
Cc: stable@vger.kernel.org
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
RSN IEs got incorrectly parsed and therefore ap mode using WPA2
security was not working.
Cc: stable@vger.kernel.org
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patches from Canonical involved the introduction of new source
files debug.[ch]. That coincided with other patches from Broadcom
introducing the same files.
Cc: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kernel 3.8 implements checking of all DMA mapping calls and issues
a WARNING for the first it finds that is not checked.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kernel 3.8 implements checking of all DMA mapping calls and issues
a WARNING for the first it finds that is not checked.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kernel 3.8 implements checking of all DMA mapping calls and issues
a WARNING for the first it finds that is not checked.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kernel 3.8 implements checking of all DMA mapping calls and issues
a WARNING for the first it finds that is not checked.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kernel 3.8 implements checking of all DMA mapping calls and issues
a WARNING for the first it finds that is not checked.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds USBIDs for:
- DrayTek Vigor 530
- Zoom 4410a
It also adds a note about Gemtek WUBI-100GW
and SparkLAN WL-682 USBID conflict [WUBI-100GW
is a ISL3886+NET2280 (LM86 firmare) solution,
whereas WL-682 is a ISL3887 (LM87 firmware)]
device.
Source: <http://www.wikidevi.com/wiki/Intersil/p54/usb/windows>
Cc: <stable@vger.kernel.org>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We fail to release 'urb' if '_rtl_prep_rx_urb()' fails in
_rtl_usb_receive().
This patch should take care of the leak.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Populate iniModesRxGain with the correct initvals
array for AR9485 v1.1
Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wlc_lcnphy_rx_iq_cal_gain is called during initialization, i. e. when
executing brcms_up.
But brcms_up is called from brcms_ops_start while the latter holds a spin lock.
Thus, we cannot use usleep_range but have to use udelay.
This fixes:
BUG: scheduling while atomic: NetworkManager/1652/0x00000200
[...]
Call Trace:
[<ffffffff81582522>] __schedule_bug+0x48/0x54
[<ffffffff815892b6>] __schedule+0x596/0x6d0
[<ffffffff81589719>] schedule+0x29/0x70
[<ffffffff8158893c>] schedule_hrtimeout_range_clock+0xfc/0x140
[<ffffffff81060f10>] ? update_rmtp+0x70/0x70
[<ffffffff81588993>] schedule_hrtimeout_range+0x13/0x20
[<ffffffff810495e0>] usleep_range+0x40/0x50
[<ffffffffa05dedcb>] wlc_lcnphy_rx_iq_cal.constprop.10+0x59b/0xa90 [brcmsmac]
[<ffffffffa05df4ce>] wlc_lcnphy_periodic_cal+0x20e/0x220 [brcmsmac]
[<ffffffffa05dce8d>] ? wlc_lcnphy_set_tx_pwr_ctrl+0x21d/0x3c0 [brcmsmac]
[<ffffffffa05e0cfc>] wlc_phy_init_lcnphy+0xacc/0x1100 [brcmsmac]
[<ffffffffa05e0230>] ? wlc_phy_txpower_recalc_target_lcnphy+0x90/0x90 [brcmsmac]
[<ffffffffa05d7c7d>] wlc_phy_init+0xcd/0x170 [brcmsmac]
[<ffffffffa05c9dfe>] brcms_b_bsinit.isra.65+0x12e/0x310 [brcmsmac]
[<ffffffffa05d061b>] brcms_c_init+0x8fb/0x1170 [brcmsmac]
[<ffffffffa05c3a0a>] brcms_init+0x5a/0x70 [brcmsmac]
[<ffffffffa05ce76c>] brcms_c_up+0x1ac/0x4a0 [brcmsmac]
[<ffffffffa05c3c65>] brcms_up+0x25/0x30 [brcmsmac]
[<ffffffffa05c44c0>] brcms_ops_start+0xd0/0x100 [brcmsmac]
[...]
Signed-off-by: Niels Ole Salscheider <niels_ole@salscheider-online.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added USB ID for T-Com Sinus 154 data II.
Cc: <stable@vger.kernel.org>
Signed-off-by: Tomasz Guszkowski <tsg@o2.pl>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sean reported that as of 3.7, his AR9170 device no longer works
because the driver fails during initialization. He noted this
is due to:
"In carl9170/fw.c, ar->hw->wiphy is tagged with
NL80211_IFTYPE_MESH_POINT support if the firmware has Content
after Beacon Queuing. This is both in interface_modes and the
only iface_combinations entry.
If CONFIG_MAC80211_MESH is not set, ieee80211_register_hw
removes NL80211_IFTYPE_MESH_POINT from interface_modes, but
not iface_combinations.
wiphy_register then checks to see if every interface type in
every interface combination is in interface_modes.
NL80211_IFTYPE_MESH_POINT was removed, so you get a WARN_ON
warning and it returns -EINVAL, giving up."
Unfortunately, the iface_combination (types) feature bitmap
in ieee80211_iface_limit is part of a const member in the
ieee80211_iface_combination struct. Hence, the MESH_POINT
feature flag can't be masked by wiphy_register in the
same way as interface_modes in ieee80211_register_hw.
Cc: <stable@vger.kernel.org>
Reported-by: Sean Patrick Santos <quantheory@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Tested-by: Sean Patrick Santos <quantheory@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Incorrect use of usb_alloc_coherent memory as input buffer to usb_control_msg
can cause problems in arch DMA code, for example kernel BUG at
'arch/arm/include/asm/dma-mapping.h:321' on ARM (linux-3.4).
Change _usb_writeN_sync use kmalloc'd buffer instead.
Cc: stable@vger.kernel.org
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since ath9k makes use of mac80211's debugfs hooks to
maintain station statistics, make ATH9K_DEBUGFS
select MAC80211_DEBUGFS. This fixes the issue reported by
Fengguang Wu:
drivers/net/wireless/ath/ath9k/debug.c: In function 'ath9k_sta_add_debugfs':
drivers/net/wireless/ath/ath9k/debug.c:1589:4: error: 'struct ath_node' has no member named 'node_stat'
drivers/net/wireless/ath/ath9k/debug.c: In function 'ath9k_sta_remove_debugfs':
drivers/net/wireless/ath/ath9k/debug.c:1599:19: error: 'struct ath_node' has no member named 'node_stat'
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
