We should wait for the last frame to complete before shutting things
down also on LCDC rev 1.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Configure video mode to HW in enable() call back. There is no reason
to do it before that. This makes PM functions way easier because there
is no HW context to save when screen is for instance blanked. This
patch removes mode_set_nofb() call back from tilcdc.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Load palette at the end of mode_set_nofb(). Moving the palette loading
to mode_set_nofb() saves us from storing and restoring of framebuffer
addresses in dma registers that were just recently written there.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add timeout wait for palette loadind to complete. We do not want to
hang forever if palette loaded interrupt does not arrive for some
reason.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The LCDC revision 2 documentation also mentions the mandatory palette
for true color modes. Even if the rev 2 LCDC appears to work just fine
without the palette being loaded loading it helps in testing the
feature.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Set LCDC_PALETTE_LOAD_MODE bit-field with new tilcdc_write_mask()
instead of tilcdc_set(). Setting a bit-fields with tilcdc_set() is
fundamentally broken.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Failed tilcdc_crtc_create() error handling was broken, this patch
should fix it.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Revision 1 of the IP doesn't work if we don't load the palette (even
if it's not used, which is the case for the RGB565 format).
Add a function called from tilcdc_crtc_enable() which performs all
required actions if we're dealing with a rev1 chip.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Revision 1 LCDC support also sync lost errors and can benefit from
sync lost recovery routine.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Recover from sync lost error flood by resetting the LCDC instead of
turning off the SYNC_LOST error IRQ. When LCDC starves on limited
memory bandwidth it may sometimes result an error situation when the
picture may have shifted couple of pixels to right and SYNC_LOST
interrupt is generated on every frame. LCDC main reset recovers from
this situation and causes a brief blanking on the screen.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Fix race from forced shutdown of crtc in unload by adding internal
locking and a boolean telling if device is going to be shutdown.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Use unload to handle initialization failures instead of complex goto
label mess. To do this the initialization sequence needed slight
reordering and some unload functions needed to become conditional.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
This error message will be printed when a FIFO underflow irq has
triggered. Since this happens sometimes and the error message will be
displayed on the console, it should have a correct spelling.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
The commit d8ff0c63fbcb ("drm/tilcdc: Adjust the FB_CEILING address")
added an adjustment of the FB_CEILING address. This is done by decrementing
the address by one.
On the AM335x (rev 0x4F201000) the framebuffer is rotated left over the
display border, because the ceiling address is 8f276fff instead of
8f277000. Since this adjustment isn't necessary for the LCDC v2, the
origin ceiling address should be used.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Some architectures don't use the common clock framework and don't
implement all the clk interfaces for every clock. This is the case
for da850-lcdk where clk_set_rate() only works for PLL0 and PLL1.
Trying to set the clock rate for the LCDC clock results in -EINVAL
being returned.
As a workaround for that: if the call to clk_set_rate() fails, fall
back to adjusting the clock divider instead. Proper divider value is
calculated by dividing the current clock rate by the required pixel
clock rate in HZ.
This code is based on a hack initially developed internally for
baylibre by Karl Beldan <kbeldan@baylibre.com>.
Tested with a da850-lcdk with an LCD display connected over VGA.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
The driver needs the number of bytes per pixel, not the bpp and depth
info meant for fbdev compatibility. Use the right API.
In the tilcdc_crtc_mode_set() function compute the hardware register
value directly from the pixel format instead of computing the number of
bits per pixels first.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1476744081-24485-7-git-send-email-laurent.pinchart@ideasonboard.com
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Iyf9
-----END PGP SIGNATURE-----
Merge tag 'tilcdc-4.9-3.1' of https://github.com/jsarha/linux into drm-next
Second attempt for 3rd drm/tilcdc pull request for v4.9.
* tag 'tilcdc-4.9-3.1' of https://github.com/jsarha/linux:
drm/tilcdc: fix wrong error handling
drm/tilcdc: Return directly after a failed kfree_table_init() in tilcdc_convert_slave_node()
drm/tilcdc: Remove "default" from blue-and-red-wiring property binding
drm/tilcdc: Fix non static symbol warning
drm/tilcdc: mark symbols static where possible
drm/tilcdc: add missing header dependencies
drm/tilcdc: WARN if CRTC is touched without CRTC lock
drm/tilcdc: Take CRTC lock when calling tilcdc_crtc_disable()
drm/tilcdc: Remove unnecessary tilcdc_crtc_disable() from tilcdc_unload()
drm/tilcdc: Flush flip-work workqueue before drm_flip_work_cleanup()
drm/tilcdc: Clean up LCDC functional clock rate setting code
drm/tilcdc: Take crtc modeset lock while updating the crtc clock rate
Also reorder alphabetically and fix up drm_flip_work header.
Reviewed-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
WARN if CRTC is touched without CRTC lock. The crtc functions should
not be called simultaneously from multiple threads. Having the DRM
CRTC lock should take care of that.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Take CRTC lock when calling tilcdc_crtc_disable() in
tilcdc_crtc_destroy().
In theory there could still be some operation ongoing, which should
finish before destroying the CRTC. However, the main reason for
adding this is to be able to add WARNing in tilcdc_crtc_disable() if
CRTC is not locked.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Flush flip-work workqueue before drm_flip_work_cleanup(). It causes a
nasty warning if there is unfinished flip-work in the queue when
drm_flip_work_cleanup() is called. The flush_workqueue() has to be
called before drm_crtc_cleanup() for unref_worker() to be able to do
its job.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Clean up LCDC functional clock rate setting code.
The LCDC functional clock is set by two functions: mode_set_nofb() and
cpufreq_transition().
When tilcdc_crtc_mode_set_nofb() is called in atomic commit phase the
drm atomic helpers have taken all the necessary drm locks and turned
off the crtc, while tilcdc_commit() is keeping LCDC powered on. For
mode_set_nofb() just a simple clock setting function without any
locking or power management code is enough. The new tilcdc_crtc_set_clk()
is implemented for that purpose.
cpufreq_transition() on the other hand is called from outside DRM and
it needs to take the necessary locks and turn off the CRTC while
keeping the LCDC powered. The reimplemented tilcdc_crtc_update_clk()
is for that purpose and it uses the new tilcdc_crtc_set_clk() to
actually set the clock.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Write DMA base and ceiling address with a single instruction, if
available. This should make it more unlikely that LCDC would fetch the
DMA addresses in the middle of an update. Having bad combination of
addresses in dma base and ceiling (e.g base > ceiling) can cause
unpredictaple behavior in LCDC.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This got accidentally dropped in the fixed commit and is required for
the driver to properly work on the rev1 IP, such as found on the LCDK.
Fixes: 2b2080d7e9 ("drm/tilcdc: Get rid of complex ping-pong mechanism")
Signed-off-by: Karl Beldan <kbeldan@baylibre.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
The LCDC seems to expect its framebuffer ceiling address pointer to be
an inclusive bound. The IP rev2 seems to cope with that but rev1 (as
found on the LCDK) don't.
Also note that this is what the framebuffer code does in da8xx-fb.c.
Since, as the TRM puts it, "The 2 LSBs are hardwired to 00b", the
dma_addr_t can be decremented without cast.
I tested it with a v2 (AM335x, rev 0x4F201000) and an LCDK (v1).
Signed-off-by: Karl Beldan <kbeldan@baylibre.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Change tilcdc_crtc_page_flip() to tilcdc_crtc_update_fb(). The
function is not used as a page_flip() callback anymore so it is only
confusing to call it that. The function should only be used by dummy
primary plane commit() callback.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Remove unnecessary pm_runtime_get() and *_put() calls from commit
phase callbacks. Those calls are not needed since we have the whole
commit phase between pm_runtime_get_sync() and pm_runtime_put_sync().
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Get rid of legacy dpms mechanism. This simplifies the code quite a
bit. The old start() and stop() functions become tilcdc_crtc_enable()
and *_disable(). The functions are added with all the necessary
mechanisms from the old dpms function and they are used directly as
the crtc helper enable() and disable() callbacks.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Enable and disable interrupts in crtc start() and stop(). None of the
interrupts can fire if CRTC is disabled, so it is cleaner - when
considering suspend/resume code etc. - to enable the interrupts when
CRTC is turned on and to disable them when CRTC is turned off.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Remove tilcdc_verify_fb(). The tilcdc_verify_fb() function is not
needed because the same checks are implemented in
tilcdc_plane_atomic_check().
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Remove obsolete crtc helper functions. These are not needed when
atomic modeset is used.
Note that the drm_crtc_helper_funcs mode_fixup() is still needed. The
crtc's check() callback can not do its job here.
The plane's check() callback needs to set drm_crtc_state's
->mode_changed to true if the pixel format for the framebuffer
changes. Because of this drm_mode_config_funcs atomic_check() callback
needs to call drm_atomic_helper_check_modeset() once more after it has
called drm_atomic_helper_check_planes(). If the fixing of the
adjusted_mode would be done in drm_crtc_helper_funcs atomic_check()
callback, it would get over written by the extra
drm_atomic_helper_check_modeset() call.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Set DRIVER_ATOMIC and use atomic helpers and rename commit and prepare
crtc helpers to enable and disable. This makes the final jump to mode
setting, but there is lot of obsolete code to clean up.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Add tilcdc_crtc_atomic_check(). Checks the display mode validity and
the presence of the mandatory primary plane.
The drm_crtc_helper_funcs mode_fixup() callback is left untouched and
the check function does no try to do its job on purpose, despite what
the mode_fixup() callback's documentations suggests.
The plane's check() callback needs to set drm_crtc_state's
->mode_changed to true if the pixel format for the framebuffer
changes. Because of this drm_mode_config_funcs atomic_check() callback
needs to call drm_atomic_helper_check_modeset() once more after it has
called drm_atomic_helper_check_planes(). If the fixing of the
adjusted_mode would be done in drm_crtc_helper_funcs atomic_check()
callback, it would get over written by the extra
drm_atomic_helper_check_modeset() call.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Add tilcdc_crtc_mode_set_nofb(). The mode_set_nofb() semantics do not
fit well to LCDC, because of the mandatory framebuffer. However, when
the primary plane is required in the check phase, it and the
framebuffer can be found from the atomic state struct.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Make tilcdc_crtc_page_flip() work if crtc is not yet on. The plane
commit sometimes comes before crtc is turned on. The new framebuffer
should be set to scanout also in that case, so that it is there when
crtc is turned on at the end of the commit phase.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Add drm_crtc_vblank_on() and *_off() calls to start() and stop()
functions, to make sure any vblank waits etc. gets properly cleaned
up.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Increase time out for waiting frame done interrupt. 50ms is long
enough for the usual display modes (50 Hz or higher refresh rate), but
it may be a bit tight for some unusual mode.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Move wait queue waiting of LCDC_FRAME_DONE IRQ from tilcdc_crtc_dpms()
into stop() function. This is just a cleanup and enables independent
use of stop() function.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reorder the IRQ function so that the write to LCDC_END_OF_INT_IND_REG
is done last. The write to LCDC_END_OF_INT_IND_REG indicates to LCDC
that the interrupt service routine has completed (see section
13.3.6.1.6 in AM335x TRM). This is needed if LCDC's ipgvmodirq module
is configured for pulse interrupts.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Move LCDC_SYNC_LOST handling inside if (ver == 2) statement.
LCDC_SYNC_LOST interrupt status bit is only defined for version 2
silicon.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Restore old dpms state in pm_resume(). The dpms is turned off in
pm_suspend() and it should be restored to its original state in
pm_resume(). Without this patch the display is left blanked after a
suspend/resume cycle.
Fixes commit 614b3cfeb8 ("drm/tilcdc: disable the lcd controller/dma
engine when suspend invoked")
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Use devm_kzalloc() and devm_kcalloc() for private data allocation at
driver load time.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Initialize port device node pointer in the tilcdc crtc. Fixes "Falling
back to first CRTC" warning from tda998x driver.
The tda998x encoder driver calls drm_of_find_possible_crtcs() to
initialize possible_crtcs of struct drm_encoder. The crtc->port needs
to be initialized for drm_of_find_possible_crtcs() to work.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Disable the sync lost interrupt if it fires on every frame for 50
consecutive frames in a row. This is relatively sure sign of the sync
lost interrupt being stuck and firing on every frame even if the
display otherwise appears to work OK.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add ratelimited prints on sync lost and FIFO underrun interrupts.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Do not update the next frame buffer close to vertical blank. This is
to avoid situation when the frame changes between writing of
LCDC_DMA_FB_BASE_ADDR_0_REG and LCDC_DMA_FB_CEILING_ADDR_0_REG.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[Added description to the patch]
Signed-off-by: Jyri Sarha <jsarha@ti.com>
