Add initial values for JP DFS pattern detector.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
and use it. This move need changes in both drivers.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Systems with multiple DFS channel detectors need to track
timestamp of previous pulse per instance to display the
correct pulse interval.
Since the interval value is used for debug printing only,
this is a non-functional modification.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Originally Helmut posted a v2 of the "ath9k: Allow platform override
without EEPROM override", but I had prematurely commited the original
as commit 552a515707. This commit restores the tree to what Helmut
intended with his v2 submission. -- JWL
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new platform data flag "use_eeprom" that indicates that the eeprom
found on the card itself should be used instead of the one present in
the platform data.
This allows to override the MAC address of a PCI card while preserving
the eeprom data from the card itself.
The default behavior is preserved.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The SREV register in the WMAC register space does not contain the chip
revision, so it needs to be passed in from the kernel.
With an updated kernel, this fixes tx gain table selection.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will enable AP mode to change channel width dynamically
based on 20/40 intolerance report sent by associated client.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A similar patch fixed crashes seen on an ath9k system
when testing against a broken ath10k AP. This patch
is slightly less protective, but probably will do the
job and is less redundant.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adjust FIR filter co-efficients to improve EVM for 11b rates.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rfsat gainchange hysteresis of rf_gain stuck with large
interference present.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I was reading ath5k power setting code and
noticed typing error in ath5k_hw_txpower function.
Invalid value was written to AR5K_PHY_TXPOWER_RATE_MAX
register.
Signed-off-by: Nikolay Ledovskikh <nledovskikh@gmail.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are some corner cases where the driver could get stuck with a full
tid queue that is paused, leading to a software tx queue hang.
Since the tx queueing rework, pausing per-tid queues on aggregation
session setup is no longer necessary. The driver will assign sequence
numbers to buffered frames when a new session is established, in order
to get the correct starting sequence number.
mac80211 prevents new frames from entering the queue during setup.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the amount of noise fluctuates strongly, low immunity settings
can sometimes disrupt signal detection on AR913x chips. When that
happens, no OFDM/CCK errors are reported anymore, and ANI tunes the
radio to the lowest immunity settings.
Usually rx/tx fails as well in that case.
To fix this, keep noise immunity settings at or above ANI default level,
which will keep radio parameters at or above INI values.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: move sc_flags to ath_common" moved setting
ATH_OP_INVALID flag below ieee80211_register_hw. This is causing
the flag never being cleared randomly as the drv_start is called
prior to setting flag. Fix this by setting the flag prior to
register_hw.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Beacon data wasn't properly cleared during early
phase of recovery. This in turn caused firmware to
crash because the beacon data was submitted before
vdevs were fully re-configured. Ultimately the
device was considered wedged and nothing worked
until driver was reloaded.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If DMA mapping of next beacon failed ath10k leaked
the beacon.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If DMA mapping of next beacon failed it was
possible for next SWBA to access a pointer that
was already unmapped and freed. This could cause
memory corruption.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If for some reason mac80211 wouldn't stop
beaconing gracefully and just removed interface of
a running AP/IBSS interface it was possible to
leak pending beacon DMA mapping. It's very
unlikely but better safe than sorry.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It doesn't make much sense to even try suspending
the device when recovering. Recovering means the
device is unresponsive and waiting for suspend
procedure means taking a 3 second timeout waiting
for tx credits.
This speeds up firmware recovery significantly.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When warm resetting it's possible for device to
crash during initialization. Instead of waiting 3
seconds just return failure as soon as
FW_IND_EVENT_PENDING is set.
This speeds up device bootup and recovery in some
cases.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This just makes it easier to tell apart different
kinds of bringup failure.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When using scatter-gather, more descriptor entries get used.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes, due to the race between Rx path and WMI_BA_STATUS_EVENTID WMI event,
few frames may be passed to the stack before reorder buffer allocated.
Then, after BACK establishment, it start getting frames with sequence number ahead of
SSN, and it get interpreted as missing frames. Then, BACK mechanism will wait
for missing frames; data traffic will be stopped. In case of interface configured
for DHCP, this data delay causes DHCP failure.
Relax checking for sequence number; use sequence of 1-st frame handled by the buffer
as SSN for this buffer.
This is work-around, real fix should be done when proper BACK mechanism implemented.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- add pcp_max_assoc_sta to the struct wmi_pcp_start_cmd
- enum for the scan ststus
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reshuffle prints to consolidate firmware/hardware information
report upon card init
Convert print for unhandled MISC ISR bits to "debug" - it is
normal situation and not an "error"
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use generic TSF timers to trigger powersave state changes based
information from the P2P NoA attribute.
Opportunistic Powersave is not handled, because the driver does not
support powersave at the moment.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Preparation for adding P2P powersave and multi-channel support.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement a recv budget so that in cases of high traffic we still allow other
taskets to get processed.
Without this, we can encounter a host of issues during high wireless traffic
reception depending on system load including rcu stall's detected (ARM),
soft lockups, failure to service critical tasks such as watchdog resets,
and triggering of the tx stuck tasklet.
The same thing was proposed previously by Ben:
http://www.spinics.net/lists/linux-wireless/msg112891.html
The only difference here is that I make sure only processed packets are counted
in the budget by checking at the end of the rx loop.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a flush is requested, make sure to clear the descriptor once we've
processed it.
This resolves a hang that will occur if all RX descriptors are full when a
flush is requested.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This way it's easier to track and debug htc tx
credit issues.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If 20MHz CAC completed successfully then
subsequent CAC with wider bandwidth (40Mhz, 80Mhz)
with identical control frequency did not start
monitor vdev making it impossible to detect any
radar pulses during intended CAC.
It also was incorrect to assume ath10k_config() will
be called after CAC is finished. Theoretically for
non-HT channels nothing changes between CAC and
start_ap() (albeit in practice this can be
different). The incorrect assumption led to CAC
not being stopped on non-HT chandefs leading to
all Rx being drooped making it impossible for
clients to associate.
While at it clean up the code a bit.
kvalo: separate WARN_ON() from the if statement
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is done to avoid forward declarations with
upcomming patches.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit "ath9k: prepare for multi-interface CSA support" added a call to
ieee80211_iterate_active_interfaces in atomic context (beacon tasklet),
which is crashing.
Use ieee80211_iterate_active_interfaces_atomic instead.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use 0-8 instead of 0-16, which is closer to the old implementation.
Also drop the overwrite of the firstep_low parameter to improve
stability.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add DFS interface combination only when
CONFIG_ATH9K_DFS_CERTIFIED is set. In other case
user can run CAC/beaconing without proper handling
of pulse events (without radar detection activated).
Reported-by: Cedric Voncken <cedric.voncken@acksys.fr>
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Frame aggregation requires the IEEE80211_TX_STAT_AMPDU to
be set so that mac80211 can report the last_tx_rate correctly.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
