intel-pinctrl for v5.17-5
* Revert misplaced ID
The following is an automated git shortlog grouped by driver:
tigerlake:
- Revert "Add Alder Lake-M ACPI ID"
It appears that last minute change moved ACPI ID of Alder Lake-M
to the INTC1055, which is already in the driver.
This ID on the other hand will be used elsewhere.
This reverts commit 258435a1c8.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
When PINCTRL_BCM63XX is selected,
and REGMAP is not selected,
Kbuild gives the following warning:
WARNING: unmet direct dependencies detected for GPIO_REGMAP
Depends on [n]: GPIOLIB [=y] && REGMAP [=n]
Selected by [y]:
- PINCTRL_BCM63XX [=y] && PINCTRL [=y]
This is because PINCTRL_BCM63XX
selects GPIO_REGMAP without selecting or depending on
REGMAP, despite GPIO_REGMAP depending on REGMAP.
This unmet dependency bug was detected by Kismet,
a static analysis tool for Kconfig. Please advise
if this is not the appropriate solution.
Signed-off-by: Julian Braha <julianbraha@gmail.com>
Link: https://lore.kernel.org/r/20220117062557.89568-1-julianbraha@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
intel-pinctrl for v5.17-4
* Couple of fixes on how Intel driver handles an interrupt
* Revert pin renaming change in ZynqMQ as it appears to be part of
the Device Tree bindings
* Fix ordering of the files in the Makefile
The following is an automated git shortlog grouped by driver:
intel:
- Fix a glitch when updating IRQ flags on a preconfigured line
- fix unexpected interrupt
Place correctly CONFIG_PINCTRL_ST in the Makefile:
- Place correctly CONFIG_PINCTRL_ST in the Makefile
zynqmp:
- Revert "Unify pin naming"
This reverts commit 54784ff249.
This patch changes the pin names from "MIO%d" to "MIO-%d", but all dts
in arch/arm64/boot/dts/xilinx still use the old name. As a result my
ZCU104 has no output on serial terminal and is not reachable over
network.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The commit af7e3eeb84 ("pinctrl: intel: Disable input and output buffer
when switching to GPIO") hadn't taken into account an update of the IRQ
flags scenario.
When updating the IRQ flags on the preconfigured line the ->irq_set_type()
is called again. In such case the sequential Rx buffer configuration
changes may trigger a falling or rising edge interrupt that may lead,
on some platforms, to an undesired event.
This may happen because each of intel_gpio_set_gpio_mode() and
__intel_gpio_set_direction() updates the pad configuration with a different
value of the GPIORXDIS bit. Notable, that the intel_gpio_set_gpio_mode() is
called only for the pads that are configured as an input. Due to this fact,
integrate the logic of __intel_gpio_set_direction() call into the
intel_gpio_set_gpio_mode() so that the Rx buffer won't be disabled and
immediately re-enabled.
Fixes: af7e3eeb84 ("pinctrl: intel: Disable input and output buffer when switching to GPIO")
Reported-by: Kane Chen <kane.chen@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Grace Kao <grace.kao@intel.com>
ASUS Chromebook C223 with Celeron N3350 crashes sometimes during
cold booot. Inspection of the kernel log showed that it gets into
an inifite loop logging the following message:
->handle_irq(): 000000009cdb51e8, handle_bad_irq+0x0/0x251
->irq_data.chip(): 000000005ec212a7, 0xffffa043009d8e7
->action(): 00000
IRQ_NOPROBE set
unexpected IRQ trap at vector 7c
The issue happens during cold boot but only if cold boot happens
at most several dozen seconds after Chromebook is powered off. For
longer intervals between power off and power on (cold boot) the issue
does not reproduce. The unexpected interrupt is sourced from INT3452
GPIO pin which is used for SD card detect. Investigation relevealed
that when the interval between power off and power on (cold boot)
is less than several dozen seconds then values of INT3452 GPIO interrupt
enable and interrupt pending registers survive power off and power
on sequence and interrupt for SD card detect pin is enabled and pending
during probe of SD controller which causes the unexpected IRQ message.
"Intel Pentium and Celeron Processor N- and J- Series" volume 3 doc
mentions that GPIO interrupt enable and status registers default
value is 0x0.
The fix clears INT3452 GPIO interrupt enabled and interrupt pending
registers in its probe function.
Fixes: 7981c0015a ("pinctrl: intel: Add Intel Sunrisepoint pin controller and GPIO support")
Signed-off-by: Łukasz Bartosik <lb@semihalf.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Two bugs have sneaked in the H616 pinctrl data:
- PH9 uses the mux value of 0x3 twice (one should be 0x5 instead)
- PH8 and PH9 use the "i2s3" function name twice in each pin
For the double pin name we use the same trick we pulled for i2s0: append
the pin function to the group name to designate the special function.
Fixes: 25adc29407 ("pinctrl: sunxi: Add support for the Allwinner H616 pin controller")
Reported-by: SASANO Takayoshi <uaa@mx5.nisiq.net>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20220105172952.23347-1-andre.przywara@arm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit bdfbef2d29 ("pinctrl: cherryview: Don't use selection 0 to mark
an interrupt line as unused") made the code properly differentiate
between unset vs (hwirq) 0 entries in the GPIO-controller interrupt-line
to GPIO pinnumber/hwirq mapping.
This is causing some boards to not boot. This commit restores the old
behavior of triggering hwirq 0 when receiving an interrupt on an
interrupt-line for which there is no mapping.
Fixes: bdfbef2d29 ("pinctrl: cherryview: Don't use selection 0 to mark an interrupt line as unused")
Reported-and-tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20220104164238.253142-1-hdegoede@redhat.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make the outer loop iterate over functions as that's the real subject.
This simplifies code (and reduces amount of lines of code) as allocating
memory for names doesn't require extra checks anymore.
While at it use local "group_names" variable. It fixes:
drivers/pinctrl/pinctrl-thunderbay.c: In function 'thunderbay_add_functions':
drivers/pinctrl/pinctrl-thunderbay.c:815:8: warning: assignment discards 'const' qualifier from pointer target type [-Wdiscarded-qualifiers]
815 | grp = func->group_names;
| ^
Ref: c26c4bfc10 ("pinctrl: keembay: rework loops looking for groups names")
Reported-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20220111172919.6567-2-zajec5@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull pin control bulk updates from Linus Walleij:
"Core changes:
- New standard enumerator and corresponding device tree bindings for
output impedance pin configuration. (Implemented and used in the
Renesas rzg2l driver.)
- Cleanup of Kconfig and Makefile to be somewhat orderly and
alphabetic.
New drivers:
- Samsung Exynos 7885 pin controller.
- Ocelot LAN966x pin controller.
- Qualcomm SDX65 pin controller.
- Qualcomm SM8450 pin controller.
- Qualcomm PM8019, PM8226 and PM2250 pin controllers.
- NXP/Freescale i.MXRT1050 pin controller.
- Intel Thunder Bay pin controller.
Enhancements:
- Introduction of the string library helper function
"kasprintf_strarray()" and subsequent use in Rockchip, ST and
Armada pin control drivers, as well as the GPIO mockup driver.
- The Ocelot pin controller has been extensively rewritten to use
regmap and other modern kernel infrastructure.
- The Microchip SGPIO driver has been converted to use regmap.
- The SPEAr driver had been converted to use regmap.
- Substantial cleanups and janitorial on the Apple pin control driver
that was merged for v5.16.
- Janitorial to remove of_node assignments in the GPIO portions that
anyway get this handled in the GPIO core.
- Minor cleanups and improvements in several pin controllers"
* tag 'pinctrl-v5.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (98 commits)
pinctrl: imx: fix assigning groups names
dt-bindings: pinctrl: mt8195: add wrapping node of pin configurations
pinctrl: bcm: ns: use generic groups & functions helpers
pinctrl: imx: fix allocation result check
pinctrl: samsung: Use platform_get_irq_optional() to get the interrupt
pinctrl: Propagate firmware node from a parent device
dt-bindings: pinctrl: qcom: Add SDX65 pinctrl bindings
pinctrl: add one more "const" for generic function groups
pinctrl: keembay: rework loops looking for groups names
pinctrl: keembay: comment process of building functions a bit
pinctrl: imx: prepare for making "group_names" in "function_desc" const
ARM: dts: gpio-ranges property is now required
pinctrl: aspeed: fix unmet dependencies on MFD_SYSCON for PINCTRL_ASPEED
pinctrl: Get rid of duplicate of_node assignment in the drivers
pinctrl-sunxi: don't call pinctrl_gpio_direction()
pinctrl-bcm2835: don't call pinctrl_gpio_direction()
pinctrl: bcm2835: Silence uninit warning
pinctrl: Sort Kconfig and Makefile entries alphabetically
pinctrl: Add Intel Thunder Bay pinctrl driver
dt-bindings: pinctrl: Add bindings for Intel Thunderbay pinctrl driver
...
Pull RISC-V SoC updates from Arnd Bergmann:
"Add support for StarFive JH7100 RISC-V SoC
This adds support for the StarFive JH7100, including the necessary
device drivers and DT files for the BeagleV Starlight prototype board,
with additional boards to be added later. This SoC promises to be the
first usable low-cost platform for RISC-V.
I've taken this through the SoC tree in the anticipation of adding a
few other Arm based SoCs as well, but those did not pass the review in
time, so it's only this one"
* tag 'newsoc-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
reset: starfive-jh7100: Fix 32bit compilation
RISC-V: Add BeagleV Starlight Beta device tree
RISC-V: Add initial StarFive JH7100 device tree
serial: 8250_dw: Add StarFive JH7100 quirk
dt-bindings: serial: snps-dw-apb-uart: Add JH7100 uarts
pinctrl: starfive: Add pinctrl driver for StarFive SoCs
dt-bindings: pinctrl: Add StarFive JH7100 bindings
dt-bindings: pinctrl: Add StarFive pinctrl definitions
reset: starfive-jh7100: Add StarFive JH7100 reset driver
dt-bindings: reset: Add Starfive JH7100 reset bindings
dt-bindings: reset: Add StarFive JH7100 reset definitions
clk: starfive: Add JH7100 clock generator driver
dt-bindings: clock: starfive: Add JH7100 bindings
dt-bindings: clock: starfive: Add JH7100 clock definitions
dt-bindings: interrupt-controller: Add StarFive JH7100 plic
dt-bindings: timer: Add StarFive JH7100 clint
RISC-V: Add StarFive SoC Kconfig option
This simplifies ns driver and gets rid of ~70 lines of code.
"const" had to be dropped from "struct ns_pinctrl_group" @pins to match
"struct group_desc" @pins and pinctrl_generic_add_group(). Otherwise it
would cause:
drivers/pinctrl/bcm/pinctrl-ns.c: In function 'ns_pinctrl_probe':
drivers/pinctrl/bcm/pinctrl-ns.c:277:13: warning: passing argument 3 of 'pinctrl_generic_add_group' discards 'const' qualifier from pointer target type [-Wdiscarded-qualifiers]
277 | group->pins, group->num_pins, NULL);
| ~~~~~^~~~~~
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20211222064344.14624-1-zajec5@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make the outer loop iterate over functions as that's the real subject.
This simplifies code (and reduces amount of lines of code) as allocating
memory for names doesn't require extra checks anymore.
While at it use local "group_names" variable. The plan for
"struct function_desc" is to make its "group_names" /double/ const. That
will allow drivers to use it with static const data.
This keembay "group_names" change is required to avoid:
drivers/pinctrl/pinctrl-keembay.c: In function 'keembay_add_functions':
drivers/pinctrl/pinctrl-keembay.c:1594:8: warning: assignment discards 'const' qualifier from pointer target type [-Wdiscarded-qualifiers]
1594 | grp = func->group_names;
| ^
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20211216162206.8027-3-zajec5@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The plan for "struct function_desc" is to make its "group_names"
/double/ const. That will allow drivers to use it with static const
data.
This imx change is required to avoid:
drivers/pinctrl/freescale/pinctrl-imx.c: In function 'imx_pinctrl_parse_functions':
drivers/pinctrl/freescale/pinctrl-imx.c:672:24: error: assignment of read-only location '*(func->group_names + (sizetype)(i * 4))'
672 | func->group_names[i] = child->name;
| ^
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20211216162206.8027-1-zajec5@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Basic StarFive JH7100 RISC-V SoC support
This adds support for the StarFive JH7100 RISC-V SoC. The SoC has many
devices that need non-coherent DMA operations to work which isn't
upstream yet[1], so this just adds basic support to boot up, get a
serial console, blink an LED and reboot itself. Unlike the Allwinner D1
this chip doesn't use any extra pagetable bits, but instead the DDR RAM
appears twice in the memory map, with and without the cache.
The JH7100 is a test chip for the upcoming JH7110 and about 300 BeagleV
Starlight Beta boards were sent out with them as part of a now cancelled
BeagleBoard.org project. However StarFive has produced more of the
JH7100s and will be selling VisionFive boards with them soon[2].
[1]: https://lore.kernel.org/linux-riscv/20210723214031.3251801-2-atish.patra@wdc.com/
[2]: https://www.cnx-software.com/2021/12/09/starfive-visionfive-single-board-computer-for-sale-accelerating-risc-v-ecosystem-development/
* tag 'jh7100-for-5.17' of https://github.com/esmil/linux:
RISC-V: Add BeagleV Starlight Beta device tree
RISC-V: Add initial StarFive JH7100 device tree
serial: 8250_dw: Add StarFive JH7100 quirk
dt-bindings: serial: snps-dw-apb-uart: Add JH7100 uarts
pinctrl: starfive: Add pinctrl driver for StarFive SoCs
dt-bindings: pinctrl: Add StarFive JH7100 bindings
dt-bindings: pinctrl: Add StarFive pinctrl definitions
reset: starfive-jh7100: Add StarFive JH7100 reset driver
dt-bindings: reset: Add Starfive JH7100 reset bindings
dt-bindings: reset: Add StarFive JH7100 reset definitions
clk: starfive: Add JH7100 clock generator driver
dt-bindings: clock: starfive: Add JH7100 bindings
dt-bindings: clock: starfive: Add JH7100 clock definitions
dt-bindings: interrupt-controller: Add StarFive JH7100 plic
dt-bindings: timer: Add StarFive JH7100 clint
RISC-V: Add StarFive SoC Kconfig option
Link: https://lore.kernel.org/r/20211216164205.286138-1-kernel@esmil.dk
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add a combined pinctrl and GPIO driver for the JH7100 RISC-V SoC by
StarFive Ltd. This is a test chip for their upcoming JH7110 SoC, which
is said to feature only minor changes to these pinctrl/GPIO parts.
For each "GPIO" there are two registers for configuring the output and
output enable signals which may come from other peripherals. Among these
are two special signals that are constant 0 and constant 1 respectively.
Controlling the GPIOs from software is done by choosing one of these
signals. In other words the same registers are used for both pin muxing
and controlling the GPIOs, which makes it easier to combine the pinctrl
and GPIO driver in one.
I wrote the pinconf and pinmux parts, but the GPIO part of the code is
based on the GPIO driver in the vendor tree written by Huan Feng with
cleanups and fixes by Drew and me.
Datasheet: https://github.com/starfive-tech/JH7100_Docs/blob/main/JH7100%20Data%20Sheet%20V01.01.04-EN%20(4-21-2021).pdf
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Co-developed-by: Huan Feng <huan.feng@starfivetech.com>
Signed-off-by: Huan Feng <huan.feng@starfivetech.com>
Co-developed-by: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
When PINCTRL_ASPEED_G* is selected,
and MFD_SYSCON is not selected,
Kbuild gives the following warnings:
WARNING: unmet direct dependencies detected for PINCTRL_ASPEED
Depends on [n]: PINCTRL [=y] && (ARCH_ASPEED [=n] || COMPILE_TEST [=y]) && OF [=y] && MFD_SYSCON [=n]
Selected by [y]:
- PINCTRL_ASPEED_G4 [=y] && PINCTRL [=y] && (MACH_ASPEED_G4 [=n] || COMPILE_TEST [=y]) && OF [=y]
WARNING: unmet direct dependencies detected for PINCTRL_ASPEED
Depends on [n]: PINCTRL [=y] && (ARCH_ASPEED [=n] || COMPILE_TEST [=y]) && OF [=y] && MFD_S>
Selected by [y]:
- PINCTRL_ASPEED_G5 [=y] && PINCTRL [=y] && (MACH_ASPEED_G5 [=n] || COMPILE_TEST [=y]) && O>
WARNING: unmet direct dependencies detected for PINCTRL_ASPEED
Depends on [n]: PINCTRL [=y] && (ARCH_ASPEED [=n] || COMPILE_TEST [=y]) && OF [=y] && MFD_S>
Selected by [y]:
- PINCTRL_ASPEED_G6 [=y] && PINCTRL [=y] && (MACH_ASPEED_G6 [=n] || COMPILE_TEST [=y]) && O>
This is because MACH_ASPEED_G* depend on (ARCH_ASPEED || COMPILE_TEST).
ARCH_ASPEED enables the MFD_SYSCON dependency, but COMPILE_TEST doesn't.
These unmet dependency bugs were detected by Kismet,
a static analysis tool for Kconfig. Please advise
if this is not the appropriate solution.
Signed-off-by: Julian Braha <julianbraha@gmail.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20211215214022.146391-1-julianbraha@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
intel-pinctrl for v5.17-3
* Intel Baytrail and Cherryview IRQ related fixes
The following is an automated git shortlog grouped by driver:
baytrail:
- Set IRQCHIP_SET_TYPE_MASKED flag on the irqchip
cherryview:
- Use temporary variable for struct device
- Do not allow the same interrupt line to be used by 2 pins
- Don't use selection 0 to mark an interrupt line as unused
...and gpio-ranges
pinctrl-bcm2835 is a combined pinctrl/gpio driver. Currently the gpio
side is registered first, but this breaks gpio hogs (which are
configured during gpiochip_add_data). Part of the hog initialisation
is a call to pinctrl_gpio_request, and since the pinctrl driver hasn't
yet been registered this results in an -EPROBE_DEFER from which it can
never recover.
Change the initialisation sequence to register the pinctrl driver
first.
This also solves a similar problem with the gpio-ranges property, which
is required in order for released pins to be returned to inputs.
Fixes: 73345a18d4 ("pinctrl: bcm2835: Pass irqchip when adding gpiochip")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211206092237.4105895-2-phil@raspberrypi.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
About Intel Thunder Bay:
-----------------------
Intel Thunder Bay is a computer vision AI accelerator SoC based on ARM CPU.
Pinctrl IP:
----------
The SoC has a customised pinmux controller IP which controls pin
multiplexing and configuration.
Thunder Bay pinctrl IP is not based on and have nothing in common with the
existing pinctrl drivers. The registers used are incompatible with the
existing drivers, so it requires a new driver.
Add pinctrl driver to enable pin control support in the Intel Thunder Bay
SoC.
Co-developed-by: Kiran Kumar S <kiran.kumar1.s@intel.com>
Signed-off-by: Kiran Kumar S <kiran.kumar1.s@intel.com>
Signed-off-by: Lakshmi Sowjanya D <lakshmi.sowjanya.d@intel.com>
Link: https://lore.kernel.org/r/20211201072626.19599-3-lakshmi.sowjanya.d@intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl: renesas: Updates for v5.17
- Add generic support for output impedance,
- Add drive strength and output impedance support for the RZ/G2L SoC,
- Miscellaneous fixes and improvements.
All the other mtk_hw_get_value() calls have a check for "if (err)" so
we can add one here as well. This silences a Smatch warning:
drivers/pinctrl/mediatek/pinctrl-mtk-common-v2.c:819 mtk_pinconf_bias_get_rsel()
error: uninitialized symbol 'pd'.
Fixes: fb34a9ae38 ("pinctrl: mediatek: support rsel feature")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20211127140836.GB24002@kili
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
