Reorder the VIM/VIM2 includes/bindings to follow the format of other dts
in the Amlogic tree and remove a stray empty line in the VIM2 dts.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20201203061605.9603-1-christianshewitt@gmail.com
Add initial support limited to HDMI i2s and SPDIF (LPCM).
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20201203060023.9454-8-christianshewitt@gmail.com
Based on the board schematics at
https://dl.radxa.com/rockpi4/docs/hw/rockpi4/rockpi_4c_v12_sch_20200620.pdf
on page 19 there is an USB Type-A receptacle being used as an USB-OTG port.
But the Type-A connector is not valid for OTG operation, for this reason
there is a switch to select host or device role.
This is non-compliant and error prone because switching is manual.
So, use host mode as it corresponds for a Type-A receptacle.
Signed-off-by: Vicente Bergas <vicencb@gmail.com>
Link: https://lore.kernel.org/r/20201201154132.1286-4-vicencb@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Based on the board schematics at
https://dl.radxa.com/rockpi4/docs/hw/rockpi4/rockpi_4c_v12_sch_20200620.pdf
on page 18:
vcc_lan is not controllable by software, it is just an analog LC filter.
Because of this, it can not be turned off-in-suspend.
and on page 17:
vcc_cam and vcc_mipi are not voltage regulators, they are just switches.
So, the voltage range is not applicable.
This silences an error message about not being able to adjust the voltage.
Signed-off-by: Vicente Bergas <vicencb@gmail.com>
Link: https://lore.kernel.org/r/20201201154132.1286-2-vicencb@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
For UARTs, the local pull-ups should be on the RX pin, not the TX pin.
UARTs transmit active-low, so a disconnected RX pin should be pulled
high instead of left floating to prevent noise being interpreted as
transmissions.
This gets rid of bogus sysrq events when the UART console is not
connected.
Fixes: 52e02d377a ("arm64: dts: rockchip: add core dtsi file for RK3328 SoCs")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20201204064805.6480-1-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Since commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e rx/tx
delay config") network is broken on the NanoPi Neo Plus2.
This patch changes the phy-mode to use internal delays both for RX and TX
as has been done for other boards affected by the same commit.
Fixes: bbc4d71d63 ("net: phy: realtek: fix rtl8211e rx/tx delay config")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201129194512.1475586-1-xypron.glpk@gmx.de
Since commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e rx/tx
delay config") iSCSI booting fails on the Pine A64 LTS.
This patch changes the phy-mode to use internal delays both for RX and TX
as has been done for other boards affected by the same commit.
Fixes: bbc4d71d63 ("net: phy: realtek: fix rtl8211e rx/tx delay config")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201129162627.1244808-1-xypron.glpk@gmx.de
The PMIC throws an errors because the clock isn't assigned to it.
Fix this by assigning the clocks info.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On the i.MX8MM Beacon SOM, there is an RTC chip which is fed power
from the baseboard during power off. The SNVS RTC integrated into
the SoC is not fed power. Depending on the order the modules are
loaded, this can be a problem if the external RTC isn't rtc0.
Make the alias for rtc0 point to the external RTC all the time and
rtc1 point to the SVNS in order to correctly hold date/time over
a power-cycle.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX8M Nano can support SPDIF which is compatible to the
IP used on the i.MX35.
Add the node.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX8M Nano has supports the MICFIL digital interface.
It's a 16-bit audio signal from a PDM microphone bitstream.
The driver is already in the kernel, but the node is missing.
Add the micfil node.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX8M Nano has several SAI nodes available to it.
Enable them.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The driver exists for the Enhanced Asynchronous Sample Rate Converter
(EASRC) Controller, but there isn't a device tree entry for it.
On the vendor kernel, they put this on a spba-bus for SDMA support.
Add the node for the spba-bus with the easrc node inside.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As the boot order in the kernel continues to change, sometimes it may
happen that the eSDHC controller mmc@2150000 (the one for eMMC) gets
probed before the one at mmc@2140000 (for external SD cards). The effect
is that the eMMC controller gets the /dev/mmcblk0 name, and the SD card
gets /dev/mmcblk1.
Since the introduction of this SoC, that has never happened in practice,
even though it was never guaranteed in theory. Setting
"root=/dev/mmcblk0p2" in /proc/cmdline has always caused the kernel to
use the second partition from the SD card as the rootfs.
The NXP development boards are typically shipped with either
- LSDK, which uses "root=UUID=", or
- OpenIL, which uses "root=/dev/mmcblkNp2"
So for OpenIL, let's preserve that old behavior by adding some aliases
which create naming consistency (for LSDK it doesn't matter):
- the SD card controller uses /dev/mmcblk0
- the eMMC controller uses /dev/mmcblk1
For the Kontron SL28 boards, Michael Walle says that they are shipped
with "root=UUID=" already, so the probing order doesn't matter, but it
is more natural to him for /dev/mmcblk0 to be the eMMC, so let's do it
the other way around there.
The aliases are parsed by mmc_alloc_host() in drivers/mmc/core/host.c.
Cc: Ashish Kumar <Ashish.Kumar@nxp.com>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The freqency 1512000000 should be 1500000000.
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Fixes: 3d9e764830 ("arm64: dts: meson-sm1-sei610: enable DVFS")
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20201130060320.GA30098@anyang-linuxfactory-or-kr
Update the VIM3/3L common dtsi to use the new function/color bindings.
Suggested-by: Artem Lapkin <art@khadas.com>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20201125052914.4092-1-christianshewitt@gmail.com
The max frequency for the w25q32 (VIM v1.2) and w25q128 (VIM v1.4) spifc
chip should be 104Mhz not 30MHz.
Fixes: b8b74dda39 ("ARM64: dts: meson-gxm: Add support for Khadas VIM2")
Signed-off-by: Artem Lapkin <art@khadas.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20201125024001.19036-1-christianshewitt@gmail.com
Tweak the node name to make it aliasable, then add aliases for the
on-board RTC chip and meson-vrtc timer so they probe as rtc0 and
rtc1 respectively.
before:
VIM3:~ # dmesg | grep rtc
[ 3.622530] meson-vrtc ff8000a8.rtc: registered as rtc0
[ 3.622574] meson-vrtc ff8000a8.rtc: setting system clock to 1970-01-01T00:00:03 UTC (3)
[ 3.646936] rtc-hym8563 0-0051: no valid clock/calendar values available
[ 3.647125] rtc-hym8563 0-0051: registered as rtc1
[ 3.852382] rtc-hym8563 0-0051: no valid clock/calendar values available
after:
VIM3:~ # dmesg | grep rtc
[ 3.583735] meson-vrtc ff8000a8.rtc: registered as rtc1
[ 3.633888] rtc-hym8563 0-0051: no valid clock/calendar values available
[ 3.634120] rtc-hym8563 0-0051: registered as rtc0
[ 3.635250] rtc-hym8563 0-0051: no valid clock/calendar values available
[ 3.635267] rtc-hym8563 0-0051: hctosys: unable to read the hardware clock
[ 3.852632] rtc-hym8563 0-0051: no valid clock/calendar values available
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20201124145338.17137-1-christianshewitt@gmail.com
GXM (S912) is a big-little design with CPUs 0-3 clocked at 1.5GHz
and CPUs 4-7 at 1.0GHz. Adding capacity-dmips-mhz attributes allows
the scheduler to factor the different clock speeds into capacity
calculations and prefer the higher-clocked cluster to improve
overall performance.
This was inspired by the similar change for G12B [0] boards. The
diference here is that all cores are A53's so the same dmips-mhz
value is used.
VIM2:~ # cat /sys/devices/system/cpu/cpu*/cpufreq/scaling_cur_freq
1512000
1512000
1512000
1512000
1000000
1000000
1000000
1000000
before:
VIM2:~ # cat /sys/devices/system/cpu/cpu*/cpu_capacity
1024
1024
1024
1024
1024
1024
1024
1024
after:
VIM2:~ # cat /sys/devices/system/cpu/cpu*/cpu_capacity
1024
1024
1024
1024
677
677
677
677
The after value matches my table-napkin calculation:
(1000000 / 1512000 = 0.661) * 1024 = 677
[0] 6eeaf4d245
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20201124121740.25704-1-christianshewitt@gmail.com
This adds the nodes for the :
- AXG PCIe PHY, using the shared analog PCIe/MIPI DSI PHY
- 2x AXG PCIe controllers
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20201120153229.3920123-4-narmstrong@baylibre.com
Enable the rtc node on VIM1/VIM2 boards so users can simply attach a power
cell and use the on-board RTC without modifying the device-tree.
Cold boot with no cell attached is gracefully handled:
VIM2:~ # dmesg | grep rtc
[ 7.716150] rtc-hym8563 1-0051: no valid clock/calendar values available
[ 7.716957] rtc-hym8563 1-0051: registered as rtc0
[ 7.729850] rtc-hym8563 1-0051: no valid clock/calendar values available
[ 7.729877] rtc-hym8563 1-0051: hctosys: unable to read the hardware clock
[ 8.126768] rtc-hym8563 1-0051: no valid clock/calendar values available
Warm boot (and any boot with cell attached) recalls stored values resulting
in consistently faster (re)boot times:
VIM2:~ # dmesg | grep rtc
[ 7.441671] rtc-hym8563 1-0051: registered as rtc0
[ 7.442663] rtc-hym8563 1-0051: setting system clock to 2020-11-16T05:49:59 UTC (1605505799)
Suggested-by: Artem Lapkin <art@khadas.com>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20201116064147.12062-1-christianshewitt@gmail.com
The Lenovo Yoga C630 drives the Boe NV133FHM-N61 eDP display from DSI
using a TI SN65DSI86 bridge chip on I2C 10. Define the bridge and eDP
panel and enable the display blocks.
Tested-by: Steev Klimaszewski <steev@kali.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20201128034231.89750-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The numbering of the i2c busses differs from ACPI and a number of typos
was made in the original patch. Further more the irq flags for the
various resources was not correct and i2c3 only has one of the two
client devices active in any one device.
Also label the various devices, for easier comparison with the ACPI
tables.
Tested-by: Steev Klimaszewski <steev@kali.org>
Fixes: 44acee2078 ("arm64: dts: qcom: Add Lenovo Yoga C630")
Link: https://lore.kernel.org/r/20201130165924.319708-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add the QPIC BAM and QPIC NAND controller support and
enable the same in board DTS file.
Co-developed-by: Anusha Canchi Ramachandra Rao <anusharao@codeaurora.org>
Signed-off-by: Anusha Canchi Ramachandra Rao <anusharao@codeaurora.org>
Signed-off-by: Kathiravan T <kathirav@codeaurora.org>
Link: https://lore.kernel.org/r/1606734105-12414-2-git-send-email-kathirav@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add the interconnects DT property to describe the ports for GENI QUPs
on the sdm845 platform.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Link: https://lore.kernel.org/r/20201105135211.7160-3-georgi.djakov@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The LID state can be read from GPIO 124 and the "tablet mode" from GPIO
95, expose these to the system using gpio-keys and mark the falling edge
of the LID state as a wakeup-source - to wake the system from suspend.
Tested-by: Steev Klimaszewski <steev@kali.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20201125060838.165576-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add crypto engine (CE) and CE BAM related nodes and definitions to
"sdm845.dtsi".
Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
Link: https://lore.kernel.org/r/20201119155233.3974286-6-thara.gopinath@linaro.org
[bjorn: Replaced RPMH_CE_CLK constant, for now]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Enable ISP and camera sensor ov2685 and ov5695 for Scarlet Chromebook
Verified with:
make ARCH=arm64 dtbs_check
Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Link: https://lore.kernel.org/r/20201020193850.1460644-10-helen.koike@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
RK3399 has two ISPs, but only isp0 was tested.
Add isp0 node in rk3399 dtsi
Verified with:
make ARCH=arm64 dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/media/rockchip-isp1.yaml
Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com>
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Link: https://lore.kernel.org/r/20201020193850.1460644-9-helen.koike@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
FW has to configure devices' StreamIDs so that SMMU is able to lookup
context and do proper translation later on. For Armada 7040 & 8040 and
publicly available FW, most of the devices are configured properly,
but some like ap_sdhci0, PCIe, NIC still remain unassigned which
results in SMMU faults about unmatched StreamID (assuming
ARM_SMMU_DISABLE_BYPASS_BY_DEFAUL=y).
Since there is dependency on custom FW let SMMU be disabled by default.
People who still willing to use SMMU need to enable manually and
use ARM_SMMU_DISABLE_BYPASS_BY_DEFAUL=n (or via kernel command line)
with extra caution.
Fixes: 83a3545d9c ("arm64: dts: marvell: add SMMU support")
Cc: <stable@vger.kernel.org> # 5.9+
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
With board revision 1.3, SolidRun moved the power LED to the middle of
the board. In old place of power LED a GPIO controllable heartbeat LED
was added. This commit only touches Single Shot variant, since only this
variant is all revision 1.3.
Reported-by: Alexandra Alth <alexandra@alth.de>
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
In accordance with the Generic xHCI bindings the corresponding node
name is suppose to comply with the Generic USB HCD DT schema, which
requires the USB nodes to have the name acceptable by the regexp:
"^usb(@.*)?" . Make sure the "generic-xhci"-compatible nodes are
correctly named.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Update the calibration table to make the temperature more accurate.
Three platforms have been updated: ls1012a, ls1043a and ls1046a.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The upstream port, doesn't really follow the vendor partitioning. The
bootloader partition has one U-Boot FIT image containing all needed
bits and pieces. Even today the bootloader is already larger than the
current "bootloader" partition. Thus, fold all the partitions into one
and keep the environment one. The latter is still valid.
We keep the failsafe partitions because the first half of the SPI flash
is preinstalled by the vendor and immutable.
Fixes: 815364d042 ("arm64: dts: freescale: add Kontron sl28 support")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the optee node which can either be enabled by a specific board or by
the bootloader.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On the LS1028A the FlexSPI clock is connected to the first HWA output,
see Figure 7 "Clock subsystem block diagram".
Fixes: c77fae5ba0 ("arm64: dts: ls1028a: Add FlexSPI support")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On the LS1028A the ENETC reference clock is connected to 4th HWA output,
see Figure 7 "Clock subsystem block diagram".
The PHC may run with a wrong frequency. ptp_qoriq_auto_config() will read
the clock speed of the clock given in the device tree. It is likely that,
on the reference board this wasn't noticed because both clocks have the
same frequency. But this must not be always the case. Fix it.
Fixes: 49401003e2 ("arm64: dts: fsl: ls1028a: add ENETC 1588 timer node")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
While running 'make dtbs_install', the following error occurs:
make[3]: *** No rule to make target 'rootfs/freescale/imx8mm-kontron-n801x-s.dts', needed by '__dtbs_install'.
It should be .dtb, not .dts.
Fixes: 8668d8b2e6 ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There are two spdif IP on imx8mq, spdif1 is for normal
spdif device, spdif2 is for HDMI ARC interface.
Enable these spdif sound card in this patch.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Configure clock rate for audio plls. audio pll1 is used
as parent clock for clocks that is multiple of 8kHz.
audio pll2 is used as parent clock for clocks that is
multiple of 11kHz.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add PCIe EP node for ls1088a to support EP mode.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Annotate the EMDIO1 node and describe the 2 AQR107 PHYs found on the
LX2160ARDB board. Also, add the necessary phy-handles for DPMACs 3 and 4
to their associated PHY.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add PCS MDIO nodes for the internal MDIO buses on the LX2160A, along
with their internal PCS PHYs, which will be used when the DPMAC is
in TYPE_PHY mode.
Also, rename the dpmac@x nodes to ethernet@x in order to be compliant
with the naming convention used by ethernet controllers.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add PCS MDIO nodes for the internal MDIO buses on the LS208x SoCs, along
with their internal PCS PHYs which will be used when the DPMAC object is
in TYPE_PHY mode.
Also, rename the dpmac@x nodes to ethernet@x in order to be compliant
with the naming convention used by ethernet controllers.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Annotate the EMDIO2 node and describe the other 4 10GBASER PHYs found on
the LS2088ARDB board. Also, add phy-handles for DPMACs 5-8 to their
associated PHY.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Annotate the EMDIO1 node and describe the 4 10GBASER PHYs found on the
LS2088ARDB board. Also, add phy-handles for DPMACs 1-4 to their
associated PHY.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the external MDIO device nodes found in the WRIOP global memory
region. This is needed for management of external PHYs.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Annotate the external MDIO2 node and describe the 10GBASER PHY found on
the LS1088ARDB board and add a phy-handle for DPMAC2 to link it.
Also, add the internal PCS MDIO node for the internal MDIO buses found
on the LS1088A SoC along with its internal PCS PHY and link the
corresponding DPMAC to the PCS through the pcs-handle.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Annotate the external MDIO1 node and describe the 8 QSGMII PHYs found on
the LS1088ARDB board and add phy-handles for DPMACs 3-10 to its
associated PHY. Also, add the internal PCS MDIO nodes for the internal
MDIO buses found on the LS1088A SoC along with their internal PCS PHY
and link the corresponding DPMAC to the PCS through the pcs-handle.
Also, rename the dpmac@x nodes to ethernet@x in order to be compliant
with the naming convention used by ethernet controllers.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the external MDIO device nodes found in the WRIOP global memory
region. This is needed for management of external PHYs.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add device tree support for LX2162AQDS board.
LX2162A has same die as of LX2160A with different packaging.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The pinmux subnodes are indented too much. This patch does nothing
more than remove an extra tab. There are no functional changes.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Rockchip RK3288 and RK3399Pro based VMARC SOM has sdio0 for
connecting WiFi/BT devices as a pluggable card via M.2 E-Key.
Add associated sdio0 nodes, properties.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20201023181814.220974-2-jagan@amarulasolutions.com
[moved the unrelated rtc addition to a separate patch]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add support for UHS modes for the SD card connected at sdhci1. This
involves adding regulators for voltage switching and power cycling the
SD card and removing the no-1-8-v property.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20201129175223.21751-3-nsekhar@ti.com
Up-to-date version of V7 schematic is on new URL linked from official
tech-spec webpage http://espressobin.net/tech-spec/
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Engicam PX30 carrier boards like EDIMM2.2 and C.TOUCH2.0 have
an onboard Sterling-LWD Wifi/BT chip based on BCM43430 connected
on the UART bus.
UART bus on the design routed via USB to UART CP20x bridge. This
bridge powered from 3V3 regualtor gpio.
This patch adds BT enablement nodes for these respective boards.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20201109181017.206834-7-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Engicam PX30 carrier boards like EDIMM2.2 and C.TOUCH2.0 have
an onboard Sterling-LWD Wifi/BT chip based on BCM43430 connected
on the SDIO bus.
The SDIO power sequnce is connacted with exteernal 32KHz oscillator
and it require 3V3 regulator input.
This patch adds WiFi enablement nodes for these respective boards.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20201109181017.206834-6-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
PX30.Core is an EDIMM SOM based on Rockchip PX30 from Engicam.
C.TOUCH 2.0 is a general purpose carrier board with capacitive
touch interface support.
10.1" OF is a capacitive touch 10.1" Open Frame panel solutions.
PX30.Core needs to mount on top of C.TOUCH 2.0 carrier with pluged
10.1" OF for creating complete PX30.Core C.TOUCH 2.0 10.1" Open Frame.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20201109181017.206834-5-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Engicam EDIMM2.2 and C.Touch 2.0 Kits support USB Host
and OTG ports.
Add support to enable USB on these kits while mounting
px30-core SOM.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20201109181017.206834-2-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives for example this error:
/arch/arm64/boot/dts/rockchip/rk3399-evb.dt.yaml:
sdhci@fe330000: $nodename:0: 'sdhci@fe330000'
does not match '^mmc(@.*)?$'
Fix it by renaming sdhci to mmc.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/
mmc/arasan,sdhci.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20201116132311.8318-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Now that driver support for the RK3328's audio codec, and the plumbing
is defined at the SoC level, we can enable analog audio at the board
level.
Enable analog audio by enabling the codec and the I2S interface
connected and the simple-audio-card that binds them together.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20201126073336.30794-4-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The RK3328-ROC-CC already has HDMI display output enabled. Now that
audio for the HDMI controller is supported, it can be enabled as well.
Enable the simple-audio-card, and the I2S interface the audio is fed
from.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20201126073336.30794-3-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The board has a standard USB A female port connected to the USB OTG
controller's data pins. Set dr_mode in the OTG controller node to
indicate this usage, instead of having the implementation guess.
Fixes: 2171f4fdac ("arm64: dts: rockchip: add roc-rk3328-cc board")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20201126073336.30794-2-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Use property name `phy-handle` instead of the deprecated `phy` to
connect eth2 to the PHY.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes: 7109d817db ("arm64: dts: marvell: add DTS for Turris Mox")
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
There are two SATA ports per CP110. Each of them has a dedicated
interrupt. Describe the real hardware by adding two SATA ports to the
CP110 SATA node.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This adds support for ESPRESSObin-Ultra from Globalscale.
Specifications are similar to the base ESPRESSObin board, with main
difference being being WAN port with PoE capability and 2 additional ethernet ports.
Full specifications:
1x Marvell 64 bit Dual Core ARM A53 Armada 3700 SOC clocked up to 1.2Ghz
1x Topaz 6341 Networking Switch
1GB DDR4
8GB eMMC
1x WAN with 30W POE
4x Gb LAN
1x RTC Clock and battery
1x DC Jack
1x USB 3.0 Type A
1x USB 2.0 Type A
1x SIM NanoSIM card Slot
1x Power Button
4x LED
1x Reset button
1x microUSB for UART
1x M.2 2280 slot for memory
1x 2x2 802.11ac Wi-Fi
1x MiniPCIE slot for Wi-Fi (PCIe interface)
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
LED2 is connected to MPP1_2 pin. It is working only on V7 boards.
V5 boards have hw bug which cause that LED2 is non-working.
So enable LED2 only for Espressobin V7 boards.
Note that LED1 is connected to LED_WLAN# pin on miniPCIe card and LED3 to
power supply. Therefore on Espressobin board only LED2 can be controlled
directly from the host. LED1 is possible to control via WiFi card inserted
in miniPCIe slot if driver for particular card supports it.
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Gérald Kerma <gerald@gk2.net>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Add initial support for the IEI Puzzle-M801 1U Rackmount Network
Appliance board.
The board is based on the quad-core Marvell Armada 8040 SoC and supports
up to 16 GB of DDR4 2400 MHz ECC RAM. It has a PCIe x16 slot (x2 lanes
only) and an M.2 type B slot.
Main system hardware:
2x USB 3.0
4x Gigabit Ethernet
2x SFP+
1x SATA 3.0
1x M.2 type B
1x RJ45 UART
1x SPI flash
1x IEI WT61P803 PUZZLE Microcontroller
1x EPSON RX8010 RTC (used instead of the integrated Marvell RTC controller)
6x SFP+ LED
1x HDD LED
All of the hardware listed above is supported and tested in this port.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
eMMC definitions in files armada-3720-espressobin-emmc.dts and
armada-3720-espressobin-v7-emmc.dts is same. So move it into common
armada-3720-espressobin.dtsi file with status "disabled".
This change simplifies eMMC variants of DTS files for Espressobin.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andre Heider <a.heider@gmail.com>
Tested-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The included armada-37xx.dtsi already defines these two aliases.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Now that the switch ports have a label in the .dtsi, simplify the whole
"switch0" block for the v7 dts files.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
There are couple of places where INTA interrupt controller
lacks #interrupt-cells property. This leads to warnings of
the type:
arch/arm64/boot/dts/ti/k3-j721e-main.dtsi:147.51-156.5: Warning (interrupt_provider): /bus@100000/main-navss/interrupt-controller@33d00000: Missing #interrupt-cells in interrupt provider
when building TI device-tree files with W=2 warning level.
Fix these.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/20201127210128.9151-1-nsekhar@ti.com
Another set of patches for devicetree files and Arm
SoC specific drivers:
- A fix for OP-TEE shared memory on non-SMP systems
- multiple code fixes for the OMAP platform, including
one regression for the CPSW network driver and a few
runtime warning fixes
- Some DT patches for the Rockchip RK3399 platform,
in particular fixing the MMC device ordering that
recently became nondeterministic with async probe.
- Multiple DT fixes for the Tegra platform, including
a regression fix for suspend/resume on TX2
- A regression fix for a user-triggered fault in the
NXP dpio driver
- A regression fix for a bug caused by an earlier bug
fix in the xilinx firmware driver
- Two more DTC warning fixes
- Sylvain Lemieux steps down as maintainer for the
NXP LPC32xx platform
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=yGOq
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-fixes-v5.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"Another set of patches for devicetree files and Arm SoC specific
drivers:
- A fix for OP-TEE shared memory on non-SMP systems
- multiple code fixes for the OMAP platform, including one regression
for the CPSW network driver and a few runtime warning fixes
- Some DT patches for the Rockchip RK3399 platform, in particular
fixing the MMC device ordering that recently became
nondeterministic with async probe.
- Multiple DT fixes for the Tegra platform, including a regression
fix for suspend/resume on TX2
- A regression fix for a user-triggered fault in the NXP dpio driver
- A regression fix for a bug caused by an earlier bug fix in the
xilinx firmware driver
- Two more DTC warning fixes
- Sylvain Lemieux steps down as maintainer for the NXP LPC32xx
platform"
* tag 'arm-soc-fixes-v5.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (24 commits)
arm64: tegra: Fix Tegra234 VDK node names
arm64: tegra: Wrong AON HSP reg property size
arm64: tegra: Fix USB_VBUS_EN0 regulator on Jetson TX1
arm64: tegra: Correct the UART for Jetson Xavier NX
arm64: tegra: Disable the ACONNECT for Jetson TX2
optee: add writeback to valid memory type
firmware: xilinx: Use hash-table for api feature check
firmware: xilinx: Fix SD DLL node reset issue
soc: fsl: dpio: Get the cpumask through cpumask_of(cpu)
ARM: dts: dra76x: m_can: fix order of clocks
bus: ti-sysc: suppress err msg for timers used as clockevent/source
MAINTAINERS: Remove myself as LPC32xx maintainers
arm64: dts: qcom: clear the warnings caused by empty dma-ranges
arm64: dts: broadcom: clear the warnings caused by empty dma-ranges
ARM: dts: am437x-l4: fix compatible for cpsw switch dt node
arm64: dts: rockchip: Reorder LED triggers from mmc devices on rk3399-roc-pc.
arm64: dts: rockchip: Assign a fixed index to mmc devices on rk3399 boards.
arm64: dts: rockchip: Remove system-power-controller from pmic on Odroid Go Advance
arm64: dts: rockchip: fix NanoPi R2S GMAC clock name
ARM: OMAP2+: Manage MPU state properly for omap_enter_idle_coupled()
...
These changes are mostly minor fixes across the board, but they also
enable PMUs on Tegra186 and enable SATA support on Jetson TX2.
-----BEGIN PGP SIGNATURE-----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=WWBT
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.11-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt
arm64: tegra: Device tree changes for v5.11-rc1
These changes are mostly minor fixes across the board, but they also
enable PMUs on Tegra186 and enable SATA support on Jetson TX2.
* tag 'tegra-for-5.11-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Fix Tegra194 HDA {clock,reset}-names ordering
arm64: tegra: Enable AHCI on Jetson TX2
arm64: tegra: Change order of SATA resets for Tegra132 and Tegra210
arm64: tegra: Add XUSB pad controller interrupt
arm64: tegra: Rename ADMA device nodes for Tegra210
arm64: tegra: Hook up edp interrupt on Tegra132 SOCTHERM
arm64: tegra: Add missing hot temperatures to Tegra210 thermal-zones
arm64: tegra: Add missing gpu-throt-level to Tegra210 soctherm
arm64: tegra: Add missing hot temperatures to Tegra132 thermal-zones
arm64: tegra: Fix DT binding for IO High Voltage entry
arm64: tegra: Fix GIC400 missing GICH/GICV register regions
arm64: tegra: Add missing CPU PMUs on Tegra186
arm64: tegra: Fix Tegra234 VDK node names
arm64: tegra: Wrong AON HSP reg property size
arm64: tegra: Fix USB_VBUS_EN0 regulator on Jetson TX1
arm64: tegra: Correct the UART for Jetson Xavier NX
arm64: tegra: Disable the ACONNECT for Jetson TX2
Link: https://lore.kernel.org/r/20201127144329.124891-5-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- PCIe endpoint support for the R-Car H3 ES2.0+ SoC.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCX8D7wQAKCRCKwlD9ZEnx
cGthAP9Tnhv6LWGL4002pLs2LS/qnPqIhWLjh+o989pKkCEJtAD9GKuzI0+tiSuk
CfPOhZUFUI7eZ99icVBPbc0yamB9UQs=
=lR48
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm-dt-for-v5.11-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM DT updates for v5.11 (take two)
- PCIe endpoint support for the R-Car H3 ES2.0+ SoC.
* tag 'renesas-arm-dt-for-v5.11-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
arm64: dts: renesas: r8a77951: Add PCIe EP nodes
Link: https://lore.kernel.org/r/20201127132155.77418-2-geert@linux-m68k.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
