This fixes a subtle bug in the calculation of the inter-packet gap and shows
that t_delta, as it is currently used, is not needed. And hence replaced.
The algorithm from RFC 3448, 4.6 below continually computes a send time t_nom,
which is initialised with the current time t_now; t_gran = 1E6 / HZ specifies
the scheduling granularity, s the packet size, and X the sending rate:
t_distance = t_nom - t_now; // in microseconds
t_delta = min(t_ipi, t_gran) / 2; // `delta' parameter in microseconds
if (t_distance >= t_delta) {
reschedule after (t_distance / 1000) milliseconds;
} else {
t_ipi = s / X; // inter-packet interval in usec
t_nom += t_ipi; // compute the next send time
send packet now;
}
1) Description of the bug
-------------------------
Rescheduling requires a conversion into milliseconds, due to this call chain:
* ccid3_hc_tx_send_packet() returns a timeout in milliseconds,
* this value is converted by msecs_to_jiffies() in dccp_write_xmit(),
* and finally used as jiffy-expires-value for sk_reset_timer().
The highest jiffy resolution with HZ=1000 is 1 millisecond, so using a higher
granularity does not make much sense here.
As a consequence, values of t_distance < 1000 are truncated to 0. This issue
has so far been resolved by using instead
if (t_distance >= t_delta + 1000)
reschedule after (t_distance / 1000) milliseconds;
The bug is in artificially inflating t_delta to t_delta' = t_delta + 1000. This
is unnecessarily large, a more adequate value is t_delta' = max(t_delta, 1000).
2) Consequences of using the corrected t_delta'
-----------------------------------------------
Since t_delta <= t_gran/2 = 10^6/(2*HZ), we have t_delta <= 1000 as long as
HZ >= 500. This means that t_delta' = max(1000, t_delta) is constant at 1000.
On the other hand, when using a coarse HZ value of HZ < 500, we have three
sub-cases that can all be reduced to using another constant of t_gran/2.
(a) The first case arises when t_ipi > t_gran. Here t_delta' is the constant
t_delta' = max(1000, t_gran/2) = t_gran/2.
(b) If t_ipi <= 2000 < t_gran = 10^6/HZ usec, then t_delta = t_ipi/2 <= 1000,
so that t_delta' = max(1000, t_delta) = 1000 < t_gran/2.
(c) If 2000 < t_ipi <= t_gran, we have t_delta' = max(t_delta, 1000) = t_ipi/2.
In the second and third cases we have delay values less than t_gran/2, which is
in the order of less than or equal to half a jiffy.
How these are treated depends on how fractions of a jiffy are handled: they
are either always rounded down to 0, or always rounded up to 1 jiffy (assuming
non-zero values). In both cases the error is on average in the order of 50%.
Thus we are not increasing the error when in the second/third case we replace
a value less than t_gran/2 with 0, by setting t_delta' to the constant t_gran/2.
3) Summary
----------
Fixing (1) and considering (2), the patch replaces t_delta with a constant,
whose value depends on CONFIG_HZ, changing the above algorithm to:
if (t_distance >= t_delta')
reschedule after (t_distance / 1000) milliseconds;
where t_delta' = 10^6/(2*HZ) if HZ < 500, and t_delta' = 1000 otherwise.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
The CCIDs are activated as last of the features, at the end of the handshake,
were the LISTEN state of the master socket is inherited into the server
state of the child socket. Thus, the only states visible to CCIDs now are
OPEN/PARTOPEN, and the closing states.
This allows to remove tests which were previously necessary to protect
against referencing a socket in the listening state (in CCID3), but which
now have become redundant.
As a further byproduct of enabling the CCIDs only after the connection has been
fully established, several typecast-initialisations of ccid3_hc_{rx,tx}_sock
can now be eliminated:
* the CCID is loaded, so it is not necessary to test if it is NULL,
* if it is possible to load a CCID and leave the private area NULL, then this
is a bug, which should crash loudly - and earlier,
* the test for state==OPEN || state==PARTOPEN now reduces only to the closing
phase (e.g. when the node has received an unexpected Reset).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
This patch does the same for CCID-3 as the previous patch for CCID-2:
s#ccid3hctx_##g;
s#ccid3hcrx_##g;
plus manual editing to retain consistency.
Please note: expanded the fields of the `struct tfrc_tx_info' in the hc_tx_sock,
since using short #define identifiers is not a good idea. The only place where
this embedded struct was used is ccid3_hc_tx_getsockopt().
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
This patch fixes two problems caused by the ubiquitous long "hctx->ccid2htx_"
and "hcrx->ccid2hcrx_" prefixes:
* code becomes hard to read;
* multiple-line statements are almost inevitable even for simple expressions;
The prefixes are not really necessary (compare with "struct tcp_sock").
There had been previous discussion of this on dccp@vger, but so far this was
not followed up (most people agreed that the prefixes are too long).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Leandro Melo de Sales <leandroal@gmail.com>
To increase robustness, it is necessary to resend Confirm feature-negotiation
options, even though the RFC does not mandate it. But feature negotiation
options can take (much) more room than the options on common DataAck packets.
Instead of reducing the MPS always for a case which only applies to the three
messages send during initial handshake, this patch devises a special case:
if the payload length of the DataAck in PARTOPEN is too large, an Ack is sent
to carry the options, and the feature-negotiation list is then flushed.
This means that the server gets two Acks for one Response. If both Acks get
lost, it is probably better to restart the connection anyway and devising yet
another special-case does not seem worth the extra complexity.
The patch (over-)estimates the expected overhead to be 32*4 bytes -- commonly
seen values were 20-90 bytes for initial feature-negotiation options.
It uses sizeof(u32) to mean "aligned units of 4 bytes". For consistency,
another use of sizeof is modified.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
The Maximum Packet Size (MPS) is of interest for applications which want
to transfer data, so it is only relevant to the data transfer phase of a
connection (unless one wants to send data on the DCCP-Request, but that is
not considered here).
The strategy chosen to deal with this requirement is to leave room for only
such options that may appear on data packets.
A special consideration applies to Ack Vectors: this is purely guesswork,
since these can have any length between 3 and 1020 bytes. The strategy
chosen here is to subtract a configurable minimum, the value of 16 bytes
(2 bytes for type/length plus 14 Ack Vector cells) has been found by
experimentatation. If people experience this as too much or too little,
this could later be turned into a Kconfig option.
There are currently no CCID-specific header options which may appear on data
packets, hence it is not necessary to define a corresponding CCID field.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
This uses the new feature-negotiation framework to signal Ack Ratio changes,
as required by RFC 4341, sec. 6.1.2.
This raises some problems for CCID-2 since it can at the moment not cope
gracefully with Ack Ratio of e.g. 2. A FIXME has thus been added which
reverts to the existing policy of bypassing the Ack Ratio sysctl.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
This patch provides support for the reception of NN options in (PART)OPEN state.
It is a combination of change_recv() and confirm_recv(), specifically geared
towards receiving the `fast-path' NN options.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
In contrast to static feature negotiation at the begin of a connection, which
establishes the capabilities of both endpoints, this patch introduces support
for dynamic exchange of feature negotiation options.
Such a dynamic exchange is necessary in at least two cases:
* CCID-2's Ack Ratio (RFC 4341, 6.1.2) which changes during the connection;
* Sequence Window values that, as per RFC 4340, 7.5.2, should be sent "as
as the connection progresses".
Both are NN (non-negotiable) features. Hence dynamic feature "negotiation" is
distinguished from static/pre-connection negotiation by the following:
* no new capabilities are negotiated (those that matter for the connection
are negotiated prior to setting up the connection, comparable to SIP);
* features must be understood by each endpoint: as per RFC 4340, 6.4,
Sequence Window is "Req'd" and Ack Ratio must be understood when CCID-2
is used as per the note underneath Table 4.
These characteristics are reflected in the implementation:
* only NN options can be exchanged after connection setup;
* NN options are activated directly after validating them. The rationale is
that a peer must accept every valid NN value (RFC 4340, 6.3.2), hence it
will either accept the value and send a "Confirm R", or it will send an
empty Confirm (which will reset the connection according to FN rules).
* An Ack is scheduled directly after activation to accelerate communicating
the update to the peer.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Since all feature-negotiation processing now takes place in feat.c, functions
for producing verbose debugging output are concentrated there.
New functions to print out values, entry records, and options are provided,
and also a macro is defined to not always have the function name in the
output line.
Thanks a lot to Wei Yongjun and Giuseppe Galeota for help with errors in an
earlier revision of this patch.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
This patch takes care of initialising and type-checking sysctls related to
feature negotiation. Type checking is important since some of the sysctls
now directly act on the feature-negotiation process.
The sysctls are initialised with the known default values for each feature.
For the type-checking the value constraints from RFC 4340 are used:
* Sequence Window uses the specified Wmin=32, the maximum is ulong (4 bytes),
tested and confirmed that it works up to 4294967295 - for Gbps speed;
* Ack Ratio is between 0 .. 0xffff (2-byte unsigned integer);
* CCIDs are between 0 .. 255;
* request_retries, retries1, retries2 also between 0..255 for good measure;
* tx_qlen is checked to be non-negative;
* sync_ratelimit remains as before.
Further changes:
----------------
Performed s@sysctl_dccp_feat@sysctl_dccp@g since the sysctls are now in feat.c.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
This adds full support for local/remote Sequence Window feature, from which the
* sequence-number-validity (W) and
* acknowledgment-number-validity (W') windows
derive as specified in RFC 4340, 7.5.3.
Specifically, the following changes are introduced:
* integrated new socket fields into dccp_sk;
* updated the update_gsr/gss routines with regard to these fields;
* updated handler code: the Sequence Window feature is located at the TX side,
so the local feature is meant if the handler-rx flag is false;
* the initialisation of `rcv_wnd' in reqsk is removed, since
- rcv_wnd is not used by the code anywhere;
- sequence number checks are not done in the LISTEN state (cf. 7.5.3);
- dccp_check_req checks the Ack number validity more rigorously;
* the `struct dccp_minisock' became empty and is now removed.
Until the handshake completes with activating negotiated values, the local/remote
Sequence-Window values are undefined and thus can not reliably be estimated.
This issue is addressed in a separate patch.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
This adds auto-loading of CCIDs (when module loading is enabled)
for the purpose of feature negotiation.
The problem with loading the CCIDs at the end of feature negotiation is
that this would happen in software interrupt context. Besides, if the host
advertises CCIDs during negotiation, it should have them ready to use, in
case an agreeing peer wants to use it for the connection.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
This initialises feature negotiation from two tables, which are initialised
from sysctls.
As a novel feature, specifics of the implementation (e.g. currently short
seqnos and ECN are not supported) are advertised for robustness.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
This removes the use of the sysctl and the minisock variable for the Send Ack
Vector feature, which is now handled fully dynamically via feature negotiation;
i.e. when CCID2 is enabled, Ack Vectors are automatically enabled (as per
RFC 4341, 4.).
Using a sysctl in parallel to this implementation would open the door to
crashes, since much of the code relies on tests of the boolean minisock /
sysctl variable. Thus, this patch replaces all tests of type
if (dccp_msk(sk)->dccpms_send_ack_vector)
/* ... */
with
if (dp->dccps_hc_rx_ackvec != NULL)
/* ... */
The dccps_hc_rx_ackvec is allocated by the dccp_hdlr_ackvec() when feature
negotiation concluded that Ack Vectors are to be used on the half-connection.
Otherwise, it is NULL (due to dccp_init_sock/dccp_create_openreq_child),
so that the test is a valid one.
The activation handler for Ack Vectors is called as soon as the feature
negotiation has concluded at the
* server when the Ack marking the transition RESPOND => OPEN arrives;
* client after it has sent its ACK, marking the transition REQUEST => PARTOPEN.
Adding the sequence number of the Response packet to the Ack Vector has been
removed, since
(a) connection establishment implies that the Response has been received;
(b) the CCIDs only look at packets received in the (PART)OPEN state, i.e.
this entry will always be ignored;
(c) it can not be used for anything useful - to detect loss for instance, only
packets received after the loss can serve as pseudo-dupacks.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Updating the NDP count feature is handled automatically now:
* for CCID-2 it is disabled, since the code does not use NDP counts;
* for CCID-3 it is enabled, as NDP counts are used to determine loss lengths.
Allowing the user to change NDP values leads to unpredictable and failing
behaviour, since it is then possible to disable NDP counts even when they
are needed (e.g. in CCID-3).
This means that only those user settings are sensible that agree with the
values for Send NDP Count implied by the choice of CCID. But those settings
are already activated by the feature negotiation (CCID dependency tracking),
hence this form of support is redundant.
At startup the initialisation of the NDP count feature is with the default
value of 0, which is done implicitly by the zeroing-out of the socket when
it is allocated. If the choice of CCID or feature negotiation enables NDP
count, this will then be updated via the NDP activation handler.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
The TX/RX CCIDs of the minisock are now redundant: similar to the Ack Vector
case, their value equals initially that of the sysctl, but at the end of
feature negotiation may be something different.
The old interface removed by this patch thus has been replaced by the newer
interface to dynamically query the currently loaded CCIDs earlier in this
patch set.
Also removed the constructors for the TX CCID and the RX CCID, since the
switch rx/non-rx is done by the handler in minisocks.c (and the handler is
the only place in the code where CCIDs are loaded).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
The code removed by this patch is no longer referenced or used, the added
lines update documentation and copyrights.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
This integrates feature-activation in the client, with these details:
1. When dccp_parse_options() fails, the reset code is already set, request_sent
_state_process() currently overrides this with `Packet Error', which is not
intended - so changed to use the reset code set in dccp_parse_options();
2. There was a FIXME to change the error code when dccp_ackvec_add() fails.
I have looked this up and found that:
* the check whether ackno < ISN is already made earlier,
* this Response is likely the 1st packet with an Ackno that the client gets,
* so when dccp_ackvec_add() fails, the reason is likely not a packet error.
3. When feature negotiation fails, the socket should be marked as not usable,
so that the application is notified that an error occurs. This is achieved
by a new label, which uses an error code of `Aborted' and which sets the
socket state to CLOSED, as well as sk_err.
4. Avoids parsing the Ack twice in Respond state by not doing option processing
again in dccp_rcv_respond_partopen_state_process (as option processing has
already been done on the request_sock in dccp_check_req).
Since this addresses congestion-control initialisation, a corresponding
FIXME has been removed.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
This patch integrates the activation of features at the end of negotiation
into the server-side code.
Note:
In dccp_create_openreq_child the request_sock argument is no longer constant,
since dccp_activate_values() uses the feature-negotiation list on dreq to sort
out the initialisation values for the different features of the child socket;
and purges this queue after use (but the `req' argument to openreq_child
can and does still remain constant).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
This first patch out of three replaces the hardcoded default settings with
initialisation code for the dynamic feature negotiation.
Note on retransmitting Confirm options:
---------------------------------------
This patch also defers flushing the client feature-negotiation queue,
due to the following considerations.
As long as the client is in PARTOPEN, it needs to retransmit the Confirm
options for the Change options received on the DCCP-Response from the server.
Otherwise, if the packet containing the Confirm options gets dropped in the
network, the connection aborts due to undefined feature negotiation state.
Thanks to Leandro Melo de Sales who reported a bug in an earlier revision
of the patch set, resulting from not retransmitting the Confirm options.
The patch now ensures that the client feature-negotiation queue is flushed only
when entering the OPEN state. Since confirmed Change options are removed as
soon as they are confirmed (in the DCCP-Response), this ensures that Confirm
options are retransmitted.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
This patch provides the post-processing of feature negotiation state, after
the negotiation has completed.
To this purpose, handlers are used and added to the dccp_feat_table. Each
handler is passed a boolean flag whether the RX or TX side of the feature
is meant.
Several handlers are provided already, new handlers can easily be added.
The initialisation is now fully dynamic, i.e. CCIDs are activated only
after the feature negotiation. The integration of this dynamic activation
is done in the subsequent patches.
Thanks to Wei Yongjun for pointing out the necessity of skipping over empty
Confirm options while copying the negotiated feature values.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Analogous to the previous patch, this adds code to interpret incoming Confirm
feature-negotiation options. Both functions operate on the feature-negotiation
list of either the request_sock (server) or the dccp_sock (client).
Thanks to Wei Yongjun for pointing out that it is overly restrictive to check
the entire list of confirmed SP values.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
This adds/replaces code for processing incoming ChangeL/R options.
The main difference is that:
* mandatory FN options are now interpreted inside the function
(there are too many individual cases to do this externally);
* the function returns an appropriate Reset code or 0,
which is then used to fill in the data for the Reset packet.
Old code, which is no longer used or referenced, has been removed.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
This provides two functions to
* reconcile preference lists (with appropriate return codes) and
* reorder the preference list if successful reconciliation changed the
preferred value.
The patch also removes the old code for processing SP/NN Change options, since
new code to process these is mostly there already; related references have been
commented out.
The code for processing Change options follows in the next patch.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
The patch implements insertion of feature negotiation at the server (listening
and request socket) and the client (connecting socket).
In dccp_insert_options(), several statements have been grouped together now
to achieve (I hope) better efficiency by reducing the number of tests each
packet has to go through:
- Ack Vectors are sent if the packet is neither a Data or a Request packet;
- a previous issue is corrected - feature negotiation options are allowed
on DataAck packets (5.8).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
This patch replaces the earlier insertion routine from options.c, so that
code specific to feature negotiation can remain in feat.c. This is possible
by calling a function already existing in options.c.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
The patch extends existing code:
* Confirm options divide into the confirmed value plus an optional preference
list for SP values. Previously only the preference list was echoed for SP
values, now the confirmed value is added as per RFC 4340, 6.1;
* length and sanity checks are added to avoid illegal memory (or NULL) access.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Support for Mandatory options is provided by this patch, which will
be used by subsequent feature-negotiation patches.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This extends the scope of two available functions, encode|decode_value_var,
to work up to 6 (8) bytes, to match maximum requirements in the RFC.
These functions are going to be used both by general option processing and
feature negotiation code, hence declarations have been put into feat.h.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This provides function to query the current TX/RX CCID dynamically, without
reliance on the minisock value, using dynamic information available in the
currently loaded CCID module.
This query function is then used to
(a) provide the getsockopt part for getting/setting CCIDs via sockopts;
(b) replace the current test for "which CCID is in use" in probe.c.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
With this patch, TX/RX CCIDs can now be changed on a per-connection basis, which
overrides the defaults set by the global sysctl variables for TX/RX CCIDs.
To make full use of this facility, the remaining patches of this patch set are
needed, which track dependencies and activate negotiated feature values.
Note on the maximum number of CCIDs that can be registered:
-----------------------------------------------------------
The maximum number of CCIDs that can be registered on the socket is constrained
by the space in a Confirm/Change feature negotiation option.
The space in these in turn depends on the size of header options as defined
in RFC 4340, 5.8. Since this is a recurring constant, it has been moved from
ackvec.h into linux/dccp.h, clarifying its purpose.
Relative to this size, the maximum number of CCID identifiers that can be
present in a Confirm option (which always consumes 1 byte more than a Change
option, cf. 6.1) is 2 bytes less than the maximum TLV size: one for the
CCID-feature-type and one for the selected value.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
This splits the setsockopt calls into two groups, depending on whether an
integer argument (val) is required and whether routines being called do
their own locking.
Some options (such as setting the CCID) use u8 rather than int, so that for
these the test with regard to integer-sizeof can not be used.
The second switch-case statement now only has those statements which need
locking and which make use of `val'.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Reviewed-by: Eugene Teo <eugeneteo@kernel.sg>
This patch deprecates the Ack Ratio sysctl, since
* Ack Ratio is entirely ignored by CCID-3 and CCID-4,
* Ack Ratio currently doesn't work in CCID-2 (i.e. is always set to 1);
* even if it would work in CCID-2, there is no point for a user to change it:
- Ack Ratio is constrained by cwnd (RFC 4341, 6.1.2),
- if Ack Ratio > cwnd, the system resorts to spurious RTO timeouts
(since waiting for Acks which will never arrive in this window),
- cwnd is not a user-configurable value.
The only reasonable place for Ack Ratio is to print it for debugging. It is
planned to do this later on, as part of e.g. dccp_probe.
With this patch Ack Ratio is now under full control of feature negotiation:
* Ack Ratio is resolved as a dependency of the selected CCID;
* if the chosen CCID supports it (i.e. CCID == CCID-2), Ack Ratio is set to
the default of 2, following RFC 4340, 11.3 - "New connections start with Ack
Ratio 2 for both endpoints";
* what happens then is part of another patch set, since it concerns the
dynamic update of Ack Ratio while the connection is in full flight.
Thanks to Tomasz Grobelny for discussion leading up to this patch.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This provides feature negotiation for server minimum checksum coverage
which so far has been missing.
Since sender/receiver coverage values range only from 0...15, their
type has also been reduced in size from u16 to u4.
Feature-negotiation options are now generated for both sender and receiver
coverage, i.e. when the peer has `forgotten' to enable partial coverage
then feature negotiation will automatically enable (negotiate) the partial
coverage value for this connection.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
The previous setsockopt interface, which passed socket options via struct
dccp_so_feat, is complicated/difficult to use. Continuing to support it leads to
ugly code since the old approach did not distinguish between NN and SP values.
This patch removes the old setsockopt interface and replaces it with two new
functions to register NN/SP values for feature negotiation. These are
essentially wrappers around the internal __feat_register functions, with
checking added to avoid
* wrong usage (type);
* changing values while the connection is in progress.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
This adds a hook to resolve features whose value depends on the choice of
CCID. It is done at the server since it can only be done after the CCID
values have been negotiated; i.e. the client will add its CCID preference
list on the Change options sent in the Request, which will be reconciled
with the local preference list of the server.
The concept is documented on
http://www.erg.abdn.ac.uk/users/gerrit/dccp/notes/feature_negotiation/\
implementation_notes.html#ccid_dependencies
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
This provides a missing link in the code chain, as several features implicitly
depend and/or rely on the choice of CCID. Most notably, this is the Send Ack Vector
feature, but also Ack Ratio and Send Loss Event Rate (also taken care of).
For Send Ack Vector, the situation is as follows:
* since CCID2 mandates the use of Ack Vectors, there is no point in allowing
endpoints which use CCID2 to disable Ack Vector features such a connection;
* a peer with a TX CCID of CCID2 will always expect Ack Vectors, and a peer
with a RX CCID of CCID2 must always send Ack Vectors (RFC 4341, sec. 4);
* for all other CCIDs, the use of (Send) Ack Vector is optional and thus
negotiable. However, this implies that the code negotiating the use of Ack
Vectors also supports it (i.e. is able to supply and to either parse or
ignore received Ack Vectors). Since this is not the case (CCID-3 has no Ack
Vector support), the use of Ack Vectors is here disabled, with a comment
in the source code.
An analogous consideration arises for the Send Loss Event Rate feature,
since the CCID-3 implementation does not support the loss interval options
of RFC 4342. To make such use explicit, corresponding feature-negotiation
options are inserted which signal the use of the loss event rate option,
as it is used by the CCID3 code.
Lastly, the values of the Ack Ratio feature are matched to the choice of CCID.
The patch implements this as a function which is called after the user has
made all other registrations for changing default values of features.
The table is variable-length, the reserved (and hence for feature-negotiation
invalid, confirmed by considering section 19.4 of RFC 4340) feature number `0'
is used to mark the end of the table.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
This provides a data structure to record which CCIDs are locally supported
and three accessor functions:
- a test function for internal use which is used to validate CCID requests
made by the user;
- a copy function so that the list can be used for feature-negotiation;
- documented getsockopt() support so that the user can query capabilities.
The data structure is a table which is filled in at compile-time with the
list of available CCIDs (which in turn depends on the Kconfig choices).
Using the copy function for cloning the list of supported CCIDs is useful for
feature negotiation, since the negotiation is now with the full list of available
CCIDs (e.g. {2, 3}) instead of the default value {2}. This means negotiation
will not fail if the peer requests to use CCID3 instead of CCID2.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Two registration routines, for SP and NN features, are provided by this patch,
replacing a previous routine which was used for both feature types.
These are internal-only routines and therefore start with `__feat_register'.
It further exports the known limits of Sequence Window and Ack Ratio as symbolic
constants.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
This patch starts the new implementation of feature negotiation:
1. Although it is theoretically possible to perform feature negotiation at any
time (and RFC 4340 supports this), in practice this is prohibitively complex,
as it requires to put traffic on hold for each new negotiation.
2. As a byproduct of restricting feature negotiation to connection setup, the
feature-negotiation retransmit timer is no longer required. This part is now
mapped onto the protocol-level retransmission.
Details indicating why timers are no longer needed can be found on
http://www.erg.abdn.ac.uk/users/gerrit/dccp/notes/feature_negotiation/\
implementation_notes.html
This patch disables anytime negotiation, subsequent patches work out full
feature negotiation support for connection setup.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
This inserts the required de-allocation routines for memory allocated by
feature negotiation in the socket destructors, replacing dccp_feat_clean()
in one instance.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
This provides feature-negotiation initialisation for both DCCP sockets and
DCCP request_sockets, to support feature negotiation during connection setup.
It also resolves a FIXME regarding the congestion control initialisation.
Thanks to Wei Yongjun for help with the IPv6 side of this patch.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
This adds list fields and list management functions for the new feature
negotiation implementation. The new code is kept in parallel to the old
code, until removed at the end of the patch set.
Thanks to Arnaldo for suggestions to improve the code.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
A lookup table for feature-negotiation information, extracted from RFC 4340/42,
is provided by this patch. All currently known features can be found in this
table, along with their feature location, their default value, and type.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
This patch prepares for the new and extended feature-negotiation routines.
The following feature-negotiation data structures are provided:
* a container for the various (SP or NN) values,
* symbolic state names to track feature states,
* an entry struct which holds all current information together,
* elementary functions to fill in and process these structures.
Entry structs are arranged as FIFO for the following reason: RFC 4340 specifies
that if multiple options of the same type are present, they are processed in the
order of their appearance in the packet; which means that this order needs to be
preserved in the local data structure (the later insertion code also respects
this order).
The struct list_head has been chosen for the following reasons: the most
frequent operations are
* add new entry at tail (when receiving Change or setting socket options);
* delete entry (when Confirm has been received);
* deep copy of entire list (cloning from listening socket onto request socket).
The NN value has been set to 64 bit, which is a currently sufficient upper limit
(Sequence Window feature has 48 bit).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
The BUG_ON(w_tot == 0) only holds if there is no more than 1 loss interval in
the loss history. If there is only a single loss interval, the calc_i_mean()
routine need in fact not be called (RFC 3448, 6.3.1).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
This sets the sysfs permissions so that root can toggle the `debug'
parameter available for nearly every DCCP module. This is useful
since there are various module inter-dependencies. The debug flag
can now be toggled at runtime using
echo 1 > /sys/module/dccp/parameters/dccp_debug
echo 1 > /sys/module/dccp_ccid2/parameters/ccid2_debug
echo 1 > /sys/module/dccp_ccid3/parameters/ccid3_debug
echo 1 > /sys/module/dccp_tfrc_lib/parameters/tfrc_debug
The last is not very useful yet, since no code at the moment calls
the tfrc_debug() macro.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
dccp_disconnect() can be called due to several reasons:
1. when the connection setup failed (inet_stream_connect());
2. when shutting down (inet_shutdown(), inet_csk_listen_stop());
3. when aborting the connection (dccp_close() with 0 linger time).
In case (1) the write queue is empty. This patch empties the write queue,
if in case (2) or (3) it was not yet empty.
This avoids triggering the write-queue BUG_TRAP in sk_stream_kill_queues()
later on.
It also seems natural to do: when breaking an association, to delete all
packets that were originally intended for the soon-disconnected end (compare
with call to tcp_write_queue_purge in tcp_disconnect()).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
This updates the use of the `out_invalid_option' label, which produces a
Reset (code 5, "Option Error"), to fill in the Data1...Data3 fields as
specified in RFC 4340, 5.6.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
This updates the option-parsing code with regard to RFC 4340, 5.8:
"[..] options with nonsensical lengths (length byte less than two or more
than the remaining space in the options portion of the header) MUST be
ignored, and any option space following an option with nonsensical length
MUST likewise be ignored."
Hence in the following cases erratic options will be ignored:
1. The type byte of a multi-byte option is the last byte of the header
options (i.e. effective option length of 1).
2. The value of the length byte is less than the minimum 2. This has been
changed from previously 3: although no multi-byte option with a length
less than 3 yet exists (cf. table 3 in 5.8), a length of 2 is valid.
(The switch-statement in dccp_parse has further per-option length checks.)
3. The option length exceeds the length of the remaining option space.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
RFC4340 states that if a packet is received with an option error (such as a
Mandatory Option as the last byte of the option list), the endpoint should
repond with a Reset.
In the LISTEN and RESPOND states, the endpoint correctly reponds with Reset,
while in the REQUEST/OPEN states, packets with option errors are just ignored.
The packet sequence is as follows:
Case 1:
Endpoint A Endpoint B
(CLOSED) (CLOSED)
<---------------- REQUEST
RESPONSE -----------------> (*1)
(with invalid option)
<---------------- RESET
(with Reset Code 5, "Option Error")
(*1) currently just ignored, no Reset is sent
Case 2:
Endpoint A Endpoint B
(OPEN) (OPEN)
DATA-ACK -----------------> (*2)
(with invalid option)
<---------------- RESET
(with Reset Code 5, "Option Error")
(*2) currently just ignored, no Reset is sent
This patch fixes the problem, by generating a Reset instead of silently
ignoring option errors.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Acked-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Thanks is due to Wei Yongjun for the detailed analysis and description of this
bug at http://marc.info/?l=dccp&m=121739364909199&w=2
The problem is that invalid packets received by a client in state REQUEST cause
the retransmission timer for the DCCP-Request to be reset. This includes freeing
the Request-skb ( in dccp_rcv_request_sent_state_process() ). As a consequence,
* the arrival of further packets cause a double-free, triggering a panic(),
* the connection then may hang, since further retransmissions are blocked.
This patch changes the order of statements so that the retransmission timer is
reset, and the pending Request freed, only if a valid Response has arrived (or
the number of sysctl-retries has been exhausted).
Further changes:
----------------
To be on the safe side, replaced __kfree_skb with kfree_skb so that if due to
unexpected circumstances the sk_send_head is NULL the WARN_ON is used instead.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thanks to Eugene Teo for reporting this problem.
Signed-off-by: Eugene Teo <eugenete@kernel.sg>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a minimum-length check for ICMPv6 packets, as per the previous
patch for ICMPv4 payloads.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Unlike TCP, which only needs 8 octets of original packet data, DCCP requires
minimally 12 or 16 bytes for ICMP-payload sequence number checks.
This patch replaces the insufficient length constant of 8 with a two-stage
test, making sure that 12 bytes are available, before computing the basic
header length required for sequence number checks.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
This adds a sequence number check for ICMPv6 DCCP error packets, in the same
manner as it has been done for ICMPv4 in the previous patch.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
The payload of ICMP message is a part of the packet sent by ourself,
so the sequence number check must use AWL and AWH, not SWL and SWH.
For example:
Endpoint A Endpoint B
DATA-ACK -------->
(SEQ=X)
<-------- ICMP (Fragmentation Needed)
(SEQ=X)
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
The AWL lower Ack validity window advances in proportion to GSS, the greatest
sequence number sent. Updating AWL other than at connection setup (in the
DCCP-Request sent by dccp_v{4,6}_connect()) was missing in the DCCP code.
This bug lead to syslog messages such as
"kernel: dccp_check_seqno: DCCP: Step 6 failed for DATAACK packet, [...]
P.ackno exists or LAWL(82947089) <= P.ackno(82948208)
<= S.AWH(82948728), sending SYNC..."
The difference between AWL/AWH here is 1639 packets, while the expected value
(the Sequence Window) would have been 100 (the default). A closer look showed
that LAWL = AWL = 82947089 equalled the ISS on the Response.
The patch now updates AWL with each increase of GSS.
Further changes:
----------------
The patch also enforces more stringent checks on the ISS sequence number:
* AWL is initialised to ISS at connection setup and remains at this value;
* AWH is then always set to GSS (via dccp_update_gss());
* so on the first Request: AWL = AWH = ISS,
and on the n-th Request: AWL = ISS, AWH = ISS + n.
As a consequence, only Response packets that refer to Requests sent by this
host will pass, all others are discarded. This is the intention and in effect
implements the initial adjustments for AWL as specified in RFC 4340, 7.5.1.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
This patch allows the sender to distinguish original and retransmitted packets,
which is in particular needed for the retransmission of DCCP-Requests:
* the first Request uses ISS (generated in net/dccp/ip*.c), and sets GSS = ISS;
* all retransmitted Requests use GSS' = GSS + 1, so that the n-th retransmitted
Request has sequence number ISS + n (mod 48).
To add generic support, the patch reorganises existing code so that:
* icsk_retransmits == 0 for the original packet and
* icsk_retransmits = n > 0 for the n-th retransmitted packet
at the time dccp_transmit_skb() is called, via dccp_retransmit_skb().
Thanks to Wei Yongjun for pointing this problem out.
Further changes:
----------------
* removed the `skb' argument from dccp_retransmit_skb(), since sk_send_head
is used for all retransmissions (the exception is client-Acks in PARTOPEN
state, but these do not use sk_send_head);
* since sk_send_head always contains the original skb (via dccp_entail()),
skb_cloned() never evaluated to true and thus pskb_copy() was never used.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Removes legacy reinvent-the-wheel type thing. The generic
machinery integrates much better to automated debugging aids
such as kerneloops.org (and others), and is unambiguous due to
better naming. Non-intuively BUG_TRAP() is actually equal to
WARN_ON() rather than BUG_ON() though some might actually be
promoted to BUG_ON() but I left that to future.
I could make at least one BUILD_BUG_ON conversion.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some places, that deal with ICMP statistics already have where
to get a struct net from, but use it directly, without declaring
a separate variable on the stack.
Since I will need this net soon, I declare a struct net on the
stack and use it in the existing places in a separate patch not
to spoil the future ones.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This corrects an error in the computation of the open loss interval I_0:
* the interval length is (highest_seqno - start_seqno) + 1
* and not (highest_seqno - start_seqno).
This condition was not fully clear in RFC 3448, but reflects the current
revision state of rfc3448bis and is also consistent with RFC 4340, 6.1.1.
Further changes:
----------------
* variable renamed due to line length constraints;
* explicit typecast to `s64' to avoid implicit signed/unsigned casting.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
This fixes a bug in the logic of the TFRC loss detection:
* new_loss_indicated() should not be called while a loss is pending;
* but the code allows this;
* thus, for two subsequent gaps in the sequence space, when loss_count
has not yet reached NDUPACK=3, the loss_count is falsely reduced to 1.
To avoid further and similar problems, all loss handling and loss detection is
now done inside tfrc_rx_hist_handle_loss(), using an appropriate routine to
track new losses.
Further changes:
----------------
* added a reminder that no RX history operations should be performed when
rx_handle_loss() has identified a (new) loss, since the function takes
care of packet reordering during loss detection;
* made tfrc_rx_hist_loss_pending() bool (thanks to an earlier suggestion
by Arnaldo);
* removed unused functions.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
RFC 4340, 7.7 specifies up to 6 bytes for the NDP Count option, whereas the code
is currently limited to up to 3 bytes. This seems to be a relict of an earlier
draft version and is brought up to date by the patch.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
The TFRC loss detection code used the wrong loss condition (RFC 4340, 7.7.1):
* the difference between sequence numbers s1 and s2 instead of
* the number of packets missing between s1 and s2 (one less than the distance).
Since this condition appears in many places of the code, it has been put into a
separate function, dccp_loss_free().
Further changes:
----------------
* tidied up incorrect typing (it was using `int' for u64/s64 types);
* optimised conditional statements for common case of non-reordered packets;
* rewrote comments/documentation to match the changes.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Change struct proto destroy function pointer to return void. Noticed
by Al Viro.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Step 8.5 in RFC 4340 says for the newly cloned socket
Initialize S.GAR := S.ISS,
but what in fact the code (minisocks.c) does is
Initialize S.GAR := S.ISR,
which is wrong (typo?) -- fixed by the patch.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
This fixes a bug in computing the inter-packet-interval t_ipi = s/X:
scaled_div32(a, b) uses u32 for b, but in "scaled_div32(s, X)" the type of the
sending rate `X' is u64. Since X is scaled by 2^6, this truncates rates greater
than 2^26 Bps (~537 Mbps).
Using full 64-bit division now.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
This fixes a bug in the reverse lookup of p: given a value f(p), instead of p,
the function returned the smallest tabulated value f(p).
The smallest tabulated value of
10^6 * f(p) = sqrt(2*p/3) + 12 * sqrt(3*p/8) * (32 * p^3 + p)
for p=0.0001 is 8172.
Since this value is scaled by 10^6, the outcome of this bug is that a loss
of 8172/10^6 = 0.8172% was reported whenever the input was below the table
resolution of 0.01%.
This means that the value was over 80 times too high, resulting in large spikes
of the initial loss interval, thus unnecessarily reducing the throughput.
Also corrected the printk format (%u for u32).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
This fixes an oversight from an earlier patch, ensuring that Ack Vectors
are not processed on request sockets.
The issue is that Ack Vectors must not be parsed on request sockets, since
the Ack Vector feature depends on the selection of the (TX) CCID. During the
initial handshake the CCIDs are undefined, and so RFC 4340, 10.3 applies:
"Using CCID-specific options and feature options during a negotiation
for the corresponding CCID feature is NOT RECOMMENDED [...]"
And it is not even possible: when the server receives the Request from the
client, the CCID and Ack vector features are undefined; when the Ack finalising
the 3-way hanshake arrives, the request socket has not been cloned yet into a
full socket. (This order is necessary, since otherwise the newly created socket
would have to be destroyed whenever an option error occurred - a malicious
hacker could simply send garbage options and exploit this.)
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
This patch fixes the following sparse warnings:
* nested min(max()) expression:
net/dccp/ccids/ccid3.c:91:21: warning: symbol '__x' shadows an earlier one
net/dccp/ccids/ccid3.c:91:21: warning: symbol '__y' shadows an earlier one
* Declaration of function prototypes in .c instead of .h file, resulting in
"should it be static?" warnings.
* Declared "struct dccpw" static (local to dccp_probe).
* Disabled dccp_delayed_ack() - not fully removed due to RFC 4340, 11.3
("Receivers SHOULD implement delayed acknowledgement timers ...").
* Used a different local variable name to avoid
net/dccp/ackvec.c:293:13: warning: symbol 'state' shadows an earlier one
net/dccp/ackvec.c:238:33: originally declared here
* Removed unused functions `dccp_ackvector_print' and `dccp_ackvec_print'.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
In commit $(825de27d9e) (from 27th May, commit
message `dccp ccid-3: Fix "t_ipi explosion" bug'), the CCID-3 window counter
computation was fixed to cope with RTTs < 4 microseconds.
Such RTTs can be found e.g. when running CCID-3 over loopback. The fix removed
a check against RTT < 4, but introduced a divide-by-zero bug.
All steady-state RTTs in DCCP are filtered using dccp_sample_rtt(), which
ensures non-zero samples. However, a zero RTT is possible on initialisation,
when there is no RTT sample from the Request/Response exchange.
The fix is to use the fallback-RTT from RFC 4340, 3.4.
This is also better than just fixing update_win_count() since it allows other
parts of the code to always assume that the RTT is non-zero during the time
that the CCID is used.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Wei Yongjun noticed that we may call reqsk_free on request sock objects where
the opt fields may not be initialized, fix it by introducing inet_reqsk_alloc
where we initialize ->opt to NULL and set ->pktopts to NULL in
inet6_reqsk_alloc.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The identification of this bug is thanks to Cheng Wei and Tomasz
Grobelny.
To avoid divide-by-zero, the implementation previously ignored RTTs
smaller than 4 microseconds when performing integer division RTT/4.
When the RTT reached a value less than 4 microseconds (as observed on
loopback), this prevented the Window Counter CCVal value from
advancing. As a result, the receiver stopped sending feedback. This in
turn caused non-ending expiries of the nofeedback timer at the sender,
so that the sending rate was progressively reduced until reaching the
minimum of one packet per 64 seconds.
The patch fixes this bug by handling integer division more
intelligently. Due to consistent use of dccp_sample_rtt(),
divide-by-zero-RTT is avoided.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC4340 said:
8.5. Pseudocode
...
If P.type is not Data, Ack, or DataAck and P.X == 0 (the packet
has short sequence numbers), drop packet and return
But DCCP has some mistake to handle short sequence numbers packet, now
it drop packet only if P.type is Data, Ack, or DataAck and P.X == 0.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dccp_feat_change() validates length and on error is returning 1.
This happens to work since call chain is checking for 0 == success,
but this is returned to userspace, so make it a real error value.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Makes the intention of the nested min/max clear.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I found some places, that erroneously return the value obtained from
the copy_to_user() call: if some amount of bytes were not able to get
to the user (this is what this one returns) the proper behavior is to
return the -EFAULT error, not that number itself.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
iwlwifi: Fix built-in compilation of iwlcore
net: Unexport move_addr_to_{kernel,user}
rt2x00: Select LEDS_CLASS.
iwlwifi: Select LEDS_CLASS.
leds: Do not guard NEW_LEDS with HAS_IOMEM
[IPSEC]: Fix catch-22 with algorithm IDs above 31
time: Export set_normalized_timespec.
tcp: Make use of before macro in tcp_input.c
hamradio: Remove unneeded and deprecated cli()/sti() calls in dmascc.c
[NETNS]: Remove empty ->init callback.
[DCCP]: Convert do_gettimeofday() to getnstimeofday().
[NETNS]: Don't initialize err variable twice.
[NETNS]: The ip6_fib_timer can work with garbage on net namespace stop.
[IPV4]: Convert do_gettimeofday() to getnstimeofday().
[IPV4]: Make icmp_sk_init() static.
[IPV6]: Make struct ip6_prohibit_entry_template static.
tcp: Trivial fix to correct function name in a comment in net/ipv4/tcp.c
[NET]: Expose netdevice dev_id through sysfs
skbuff: fix missing kernel-doc notation
[ROSE]: Fix soft lockup wrt. rose_node_list_lock
What do_gettimeofday() does is to call getnstimeofday() and
to convert the result from timespec{} to timeval{}.
We do not always need timeval{} and we can convert timespec{}
when we really need (to print).
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
None of these files use any of the functionality promised by
asm/semaphore.h. It's possible that they rely on it dragging in some
unrelated header file, but I can't build all these files, so we'll have
fix any build failures as they come up.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
As I can see from the code, two places (tcp_v6_syn_recv_sock and
dccp_v6_request_recv_sock) that call this one already run with
BHs disabled, so it's safe to call __inet_inherit_port there.
Besides (in case I missed smth with code review) the calltrace
tcp_v6_syn_recv_sock
`- tcp_v4_syn_recv_sock
`- __inet_inherit_port
and the similar for DCCP are valid, but assumes BHs to be disabled.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
These sockets now have a bit other names and are no longer global.
Shame on me, I haven't provided a good comment for this when
sending DCCP netnsization patches.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The inet6_lookup family of functions requires a net to lookup
a socket in, so give a proper one to them.
No more things to do for dccpv6, since routing is OK and the
ipv4-like transport layer filtering is not done for ipv6.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the call to inet_ctl_sock_create to init callback (and
inet_ctl_sock_destroy to exit one) and use proper ctl sock
in dccp_v6_ctl_send_reset.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And replace all its usage with init_net's socket.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
They will be responsible for ctl socket initialization, but
currently they are void.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This call uses the sock to get the net to lookup the routing
in. With CONFIG_NET_NS this code will OOPS, since the sk ptr
is NULL.
After looking inside the ip6_dst_lookup and drawing the analogy
with respective ipv6 code, it seems, that the dccp ctl socket
is a good candidate for the first argument.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables sockets creation with IPPROTO_DCCP and enables
the ip level to pass DCCP packets to the DCCP level.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The inet_lookup family of functions requires a net to lookup
a socket in, so give a proper one to them.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dccp_v4_route_skb used in dccp_v4_ctl_send_reset, currently
works with init_net's routing tables - fix it.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the call to inet_ctl_sock_create to init callback (and
inet_ctl_sock_destroy to exit one) and use proper ctl sock
in dccp_v4_ctl_send_reset.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
