Hi,
my Huawei 3G modem has an embedded Smart Card reader which causes
trouble when the modem is being detected (a bunch of "<warn> (ttyUSBx):
open blocked by driver for more than 7 seconds!" in messages.log). This
trivial patch corrects the problem for me. The modem identifies itself
as "12d1:1406 Huawei Technologies Co., Ltd. E1750" in lsusb although the
description on the body says "Model E173u-1"
Signed-off-by: Michal Malý <madcatxster@prifuk.cz>
Cc: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DCD pin of the serial port can receive a PPS signal. By calling
the port line discipline dcd handle, this patch allow to monitor PPS
through USB serial devices.
However the performance aren't as good as the uart drivers, so
document this point too.
Signed-off-by: Paul Chavent <paul.chavent@onera.fr>
Acked-by: Rodolfo Giometti <giometti@enneenne.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the device receive a DCD status change, forward the signal to the
USB serial system. This way, we can detect, for instance, PPS pulses.
Signed-off-by: Paul Chavent <paul.chavent@onera.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to Prolific, several (unauthorized) cheap and less functional
clones of the PL2303HX chip are in circulation. [1]
I've had the chance to test such a cloned device and it turned out that
it doesn't support any baud rates above 115200 baud (original: 6 Mbaud)
It also doesn't support the divisior based baud rate encoding method,
so no continuous baud rate adjustment is possible.
Nevertheless, these devices have been working (unintentionally) with
the driver up to commit 61fa8d694b ("pl2303: also use the divisor based
baud rate encoding method for baud rates < 115200 with HX chips"), and
this commit broke support for them.
Fortunately, it is pretty simple to distinguish between the original
and the cloned HX chips, so I've added a check and an extra chip type
to keep the clones working.
The same check is used by the latest Prolific Windows driver, so it
should be solid.
[1] http://www.prolific.com.tw/US/ShowProduct.aspx?p_id=225&pcid=41
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big driver core pull request for 3.12-rc1.
Lots of tiny changes here fixing up the way sysfs attributes are
created, to try to make drivers simpler, and fix a whole class race
conditions with creations of device attributes after the device was
announced to userspace.
All the various pieces are acked by the different subsystem maintainers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.21 (GNU/Linux)
iEYEABECAAYFAlIlIPcACgkQMUfUDdst+ynUMwCaAnITsxyDXYQ4DqEsz8EcOtMk
718AoLrgnUZs3B+70AT34DVktg4HSThk
=USl9
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg KH:
"Here's the big driver core pull request for 3.12-rc1.
Lots of tiny changes here fixing up the way sysfs attributes are
created, to try to make drivers simpler, and fix a whole class race
conditions with creations of device attributes after the device was
announced to userspace.
All the various pieces are acked by the different subsystem
maintainers"
* tag 'driver-core-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (119 commits)
firmware loader: fix pending_fw_head list corruption
drivers/base/memory.c: introduce help macro to_memory_block
dynamic debug: line queries failing due to uninitialized local variable
sysfs: sysfs_create_groups returns a value.
debugfs: provide debugfs_create_x64() when disabled
rbd: convert bus code to use bus_groups
firmware: dcdbas: use binary attribute groups
sysfs: add sysfs_create/remove_groups for when SYSFS is not enabled
driver core: add #include <linux/sysfs.h> to core files.
HID: convert bus code to use dev_groups
Input: serio: convert bus code to use drv_groups
Input: gameport: convert bus code to use drv_groups
driver core: firmware: use __ATTR_RW()
driver core: core: use DEVICE_ATTR_RO
driver core: bus: use DRIVER_ATTR_WO()
driver core: create write-only attribute macros for devices and drivers
sysfs: create __ATTR_WO()
driver-core: platform: convert bus code to use dev_groups
workqueue: convert bus code to use dev_groups
MEI: convert bus code to use dev_groups
...
Clean up the DEVICE_ATTR usage in the USB serial drivers, making them
more obvious as to the permissions that the sysfs files should be.
Note: ftdi_sio.c still has a DEVICE_ATTR() used, that will have to wait
until after 3.12-rc1 comes out when DEVICE_ATTR_WO() shows up in Linus's
tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The drv_attrs field of struct bus_type is going away soon, drv_groups
should be used instead. This converts the USB serial bus code to use
the correct field.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix endianess bugs in parallel-port code which caused corrupt
control-requests to be issued on big-endian machines.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The write_parport_reg_nonblock() function shouldn't sleep because it's
called with spinlocks held.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@vger.kernel.org
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb-serial-simple uses an unknown stringify macro that make
all drivers being named "stringify(vendor)".
This can be a problem when two drivers have the same (wrong) name:
kernel: usbcore: registered new interface driver usb_serial_simple
kernel: usbserial: USB Serial support registered for stringify(vendor)
kernel Error: Driver 'stringify(vendor)' is already registered, aborting...
kernel: usbserial: problem -16 when registering driver stringify(vendor)
kernel: usbserial: USB Serial deregistering driver stringify(vendor)
kernel: usbcore: deregistering interface driver usb_serial_simple
Before the fix:
$ strings drivers/usb/serial/usb-serial-simple.o
usb_serial_simple
stringify(vendor)
After the fix:
$ strings drivers/usb/serial/usb-serial-simple.o
usb_serial_simple
funsoft
flashloader
vivopay
moto_modem
hp4x
suunto
siemens_mpi
This patch makes usb-serial-simple use the correct stringify operator.
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure serial DMA-buffers are allocated separately from containing
structure to prevent potential memory corruption on non-cache-coherent
systems.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure serial DMA-buffers are allocated separately from containing
structure to prevent potential memory corruption on non-cache-coherent
systems.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure port DMA-buffers are allocated separately from containing
structure to prevent potential memory corruption on non-cache-coherent
systems.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure serial DMA-buffers are allocated separately from containing
structure to prevent potential memory corruption on non-cache-coherent
systems.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to fail properly if the device is not accepted during attach
in order to avoid null-pointer derefs (of missing interface private
data) at disconnect or release.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The parallel-port code of the drivers used a stack allocated
control-request buffer for asynchronous (and possibly deferred) control
requests. This not only violates the no-DMA-from-stack requirement but
could also lead to corrupt control requests being submitted.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver currently knows about 3 different PL2303 chip types:
The two legacy chip types type_0 and type_1 (PL2303H ?) and the HX
type.
The device distinction is currently completely based on the examination
of the USB descriptors.
During the last years, Prolific has introduced further PL2303 chips,
such as the HXD (HX rev. D), TA (which replaced the X/HX chips), SA,
RA, EA and TB variants.
Unfortunately, all these new chips are currently detected as HX chips,
because they are all using the same bMaxPacketSize0 = 0x40 value in the
USB device descriptor.
At this point it is not clear if these chips are really working with
the driver, there are just some positive indicators (like device
manufacturers claiming Linux support for these devices or commit
8d48fdf689 "correctly handle baudrates above 115200" which should only
be necessary for newer devices, ...)
For a complete support of all devices, we need to distinguish between
them, because they differ in several functional aspects, such as the
maximum supported baud rate (HXD, TB, EA: 12Mbps, HX, TA: 6Mbps,
RA: 1Mbps, SA: 115.2kbps), handshaking line support, RS422/485 and
GPIO ports support (currently not supported by the driver).
And there might be further differences that we don't know yet.
This patch improves the chip type detection by evaluating the bcdDevice
value of the device descriptor. The values are taken from the
datasheets and are safe to use because manufacturers can't change them:
3.00: X/HX, TA
4.00: HXD, EA, RA, SA
5.00: TB
The rest of the device descriptors is completely identical, so no
further distinction is possible this way.
Anyway, Prolifics "checkChipVersion.exe"-tool is definitely able to
distinguish for example between the X/HX and the TA chips, so there
must be a possibility to improve the distinction further...
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The chip type distinction is getting more and more relevant and
complicating, so always print the chip type.
Printing a name string is also much better than just printing an
internal index number.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need for two else-if constructs for the type_1 chip
detection in pl2303_startup(), so merge them.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I've found some new datasheets which describe some additionally
supported standard baud rates and I've verified them with my HX
(rev. 3A) device. But adding support for individual (chip type
specific) baud rates would add a good amount of extra code (especially
when support for further chips will be added to the driver one day),
which makes no sense as long as we are not using the direct baud rate
encoding method for newer chips.
So for now, just drop a comment about these additionally supported baud
rates.
The second comment is about the baud rate differences between the two
encoding methods. In theory, we could optimize the code a bit by
comparing the resulting baud rates of both methods and selecting the
one which is closer to the requested baud rate. But that seems to be a
bit overkill, because the differences are very small and the device
likely uses the same baud rate generator for both methods so that the
resulting baud rate would be the same.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the divisor based baud rate encoding method has been fixed and
extended, it can also be used for baud rates < 115200 baud with HX
chips.
This makes it possible to adjust the baud rate almost continuously
instead of just beeing able to select between 16 fixed standard values.
Tested with a PL2303HX 04463A (week 46, 2004, rev 3A).
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reinhard Max has done some tests with a PL2303HX (rev A) and a logic
analyzer and it seems, that although the PL2303HX is specified for baud
rates from 75 to 6M baud, the full divisor range can be used with the
divisor based baud rate encoding method. This corresponds to baud rates
from 46 to 24M baud.
Baud rates down to 46 baud (max. divisor) have been confirmed to work
even under heavy/permanent load, so remove the lower limit.
Baud rates up to 24M baud should really be tested carefully in "real
life" scenarios before removing the upper limit completely.
Anyway, the Windows driver allows maximum baud rates of 110% of the
specified limit, so for now, increase the upper limit to this value.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Reinhard Max <max@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 0c967e7e "USB: serial: pl2303 works at 500kbps" added 500000
baud to the list of supported standard baud rates.
But the reason why the driver works with this baud rate is, that since
commit 8d48fdf6 "USB: PL2303: correctly handle baudrates above 115200"
a second (divisor based) baud rate encoding method is used for values
above 115200 baud, which is not limited to a fixed set of standard baud
rates.
Remove the 500000 baud value from the list of standard baud rates
again, because this list is only used with the direct baud rate
encoding method and 500000 baud is not supported with this method.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In opposition to the direct baud rate encoding method, the divisor
based method is not limited to a fixed set of standard baud rates.
Hence, there is no need to round to the next nearest standard value.
Reported-by: Mastro Gippo <gipmad@gmail.com>
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Reinhard Max <max@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on the formula in the code description, Reinhard Max and me have
investigated the devices behavior / functional principle of the divisor
based baud rate encoding method.
It turned out, that (although beeing a good starting point) the current
code has some flaws. It doesn't work correctly for a wide range of baud
rates and the divisor resolution can be improved. It also doesn't
report the actually set baud rate.
This patch fixes and improves the code for the divisor based baud rate
encoding method a lot. It can now be used for the whole range of baud
rates from 46 baud to 24M baud with a very good divisor resolution and
userspace can read back the resulting baud rate.
It also documents the formula used for encoding and the hardware
behavior (including special cases).
The basic algorithm, rounding and several code comments/explanations
are provided by Reinhard Max.
I've added some minor fixes, the handling of the special cases and
further code/algorithm descriptions.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Reinhard Max <max@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix endianess bugs in firmware handling introduced by commits cb7a7c6a
("ti_usb_3410_5052: add Multi-Tech modem support") and 05a3d905
("ti_usb_3410_5052: support alternate firmware") which made the driver
use the wrong firmware for certain devices on big-endian machines.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix bug in device-type detection on big-endian machines originally
introduced by commit 0eafe4de ("USB: serial: mos7840: add support for
MCS7810 devices") which always matched on little-endian product ids.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes an issue where the bulk-in urb used for incoming data transfer
is not resubmitted if the packet recieved contains an error status. This
results in the driver locking until the port is closed and re-opened.
Tested on a custom board with a Cinterion GSM module.
Signed-off-by: Matt Burtch <matt@grid-net.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of having to create a new driver for a "simple" usb to serial
device, mush them all into one file, with a macro, so as to make it easy
to add new ones.
Cc: "René Bürgel" <rene.buergel@sohard.de>
Acked-by: Wei Shuai <cpuwolf@gmail.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Acked-by: Frans Klaver <frans.klaver@xsens.com>
Cc: "Wesley W. Terpstra" <w.terpstra@gsi.de>
Cc: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's not clear if the type_0 and type_1 chips support the divisor based baud
rate encoding method, so don't use it until anyone with such chip has tested it
to avoid regressions with the following patches.
Even if it has been working fine with these chips since the code has been added
2 years ago, this change will not cause any regressions, because the baud rates
currently supported/allowed with the divisor based method are supported with
the direct method, too.
The code for the divisor based method also isn't entirely correct (yet), so that the
direct encoding method actually works better (sets the baud rate more precisely).
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RT Systems makes many usb serial cables based on the ftdi_sio driver for
programming various amateur radios. This patch is a full listing of
their current product offerings and should allow these cables to all
be recognized.
Signed-off-by: Rick Farina (Zero_Chaos) <zerochaos@gentoo.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following regression that has been introduced recently with
commit b2d6d98fc7:
With type_0 and type_1 chips
- all baud rates < 1228800 baud are rounded up to 1228800 baud
- the device silently runs at 9600 baud for all baud rates > 1228800
baud
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Silence compiler warnings on 64-bit systems introduced by commit
05cf0dec ("USB: mos7840: fix race in led handling") which uses the
usb-serial data pointer to temporarily store the device type during
probe but failed to add the required casts.
[gregkh - change uintptr_t to unsigned long]
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix race in LED handling introduced by commit 0eafe4de ("USB: serial:
mos7840: add support for MCS7810 devices") which reused the port control
urb for manipulating the LED without making sure that the urb is not
already in use. This could lead to the control urb being manipulated
while in flight.
Fix by adding a dedicated LED urb and ctrlrequest along with a LED-busy
flag to handle concurrency.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix race in device-type detection introduced by commit 0eafe4de ("USB:
serial: mos7840: add support for MCS7810 devices") which used a static
variable to hold the device type.
Move type detection to probe and use serial data to store the device
type.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix race in mos7840_get_reg which unconditionally manipulated the
control urb (which may already be in use) by adding a control-urb busy
flag.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds a driver for the Suunto ANT+ USB device, exposing it as a usb
serial device. This lets the userspace "gant" program to talk to the
device to communicate over the ANT+ protocol to any devices it finds.
Reported-by: Steinar Gunderson <sgunderson@bigfoot.com>
Tested-by: Steinar Gunderson <sgunderson@bigfoot.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allocated urbs and buffers were never freed on errors in open.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some (very few) early devices like mine, where not exposting a proper CDC
descriptor. This was fixed with an immediate firmware update from the vendor,
and pre-installed on newer devices.
So actual devices can be driven by cdc_acm.c + cdc_ether.c.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Speaks AT on interfaces 5 (command & PPP) and 3 (secondary), other
interface protocols are unknown.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prevent the option driver from binding itself to the QMI/WWAN interface, making
it unusable by the proper driver.
Signed-off-by: enrico Mioso <mrkiko.rs@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for the ONYX 3G device (version 1) from ALFA
NETWORK.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver failed to take the dynamic ids into account when determining
the device type and therefore all devices were detected as 2-port
devices when using the dynamic-id interface.
Match on the usb-serial-driver field instead of doing redundant id-table
searches.
Reported-by: Anders Hammarquist <iko@iko.pp.se>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the vendor and product module parameters which were added a long
time ago when we did not have the dynamic sysfs interface to add
new device ids (and which isn't limited to five new vid/pid pair).
A vid/pid pair can be added dynamically using sysfs, for example:
echo 0451 1234 >/sys/bus/usb-serial/drivers/ti_usb_3410_5052_1/new_id
for 1-port adapters, or
echo 0451 1234 >/sys/bus/usb-serial/drivers/ti_usb_3410_5052_2/new_id
for 2-port adapters.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The write wait queue is never added to since commit f1175daa5 ("USB:
ti_usb_3410_5052: kill custom closing_wait"). Remove it completely.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kill private write fifo and use the already allocated port write fifo
instead.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the vendor and product module parameters which were added a long
time ago when we did not have the dynamic sysfs interface to add
new device ids (and which isn't limited to a single new vid/pid pair).
A vid/pid pair can be added dynamically using sysfs, for example:
echo 04dd 1234 >/sys/bus/usb-serial/drivers/safe_serial/new_id
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove broken "chase" implementation which was supposed to be used to
drain the write buffers at break.
The chase implementation slept on a wait queue which was never woken up
(i.e. no hardware buffers were queried), and thus amounted to nothing
more than polling chars_in_buffer, something which has already been
taken care of by the tty layer.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move port initialisation code from open to probe where it belongs.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kill private write fifo and use the already allocated port write fifo
instead.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the vendor and product module parameters which were added a long
time ago when we did not have the dynamic sysfs interface to add
new device ids (and which isn't limited to a single new vid/pid pair).
A vid/pid pair can be added dynamically using sysfs, for example:
echo 0403 1234 >/sys/bus/usb-serial/drivers/ftdi_sio/new_id
Also fix up the in-code comment that got the sysfs path wrong.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not raise DTR/RTS a second time in set_termios at open -- this has
already been taken care of by the tty layer.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not use zeroed termios data to determine when to unconditionally
configure the device at open.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure set_termios is not called with uninitialised data at open. The
old termios struct is currently not used, but pass NULL instead to avoid
future problems (e.g. stack data leak).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only log the tty_flags in process_read_urb on errors.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Break out baud-rate handling from set_termios.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unnecessary tests for open and write operations as these are set
to the generic implementations by usb-serial core if left unset by a
subdriver.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port drain delay is constant and should be set at port probe rather
than open.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 957dacae ("TTY: fix DTR not being dropped on hang up")
dtr_rts is no longer called for uninitialised ports (e.g. after
a disconnect), which removes the need to grab the disconnect mutex.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 31ca020b ("TTY: wake up processes last at hangup") there no
longer any need to check the hupping flag in the generic tiocmiwait
implementation, so remove it.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove defensive test from set_termios which is never called with a NULL
tty.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added support for MMB Networks and Planet Innovation Ingeni ZigBee USB
devices using customized Silicon Labs' CP210x.c USB to UART bridge
drivers with PIDs: 88A4, 88A5.
Signed-off-by: Sami Rahman <sami.rahman@mmbresearch.com>
Tested-by: Sami Rahman <sami.rahman@mmbresearch.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for the Schweitzer Engineering Laboratories
C662 USB cable based off the CP210x driver.
Signed-off-by: Barry Grussling <barry@grussling.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch was tested on 3.10.1 kernel.
Same models of Petatel NP10T modems have different device IDs.
Unfortunately they have no additional revision information on a board
which may treat them as different devices. Currently I've seen only
two NP10T devices with various IDs. Possibly Petatel NP10T list will
be appended upon devices with new IDs will appear.
Signed-off-by: Daniil Bolsun <dan.bolsun@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds NetGear Managed Switch M4100 series, M5300 series, M7100 series
USB ID (0846:0110) to the cp210x driver. Without this, the serial
adapter is not recognized in Linux. Description was obtained from
an Netgear Eng.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These devices are all Gobi1K devices (according to the Windows INF
files) and should be handled by qcserial instead of option. Their
network port is handled by qmi_wwan.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add product id for Abbott strip port cable for Precision meter which
uses the TI 3410 chip.
Signed-off-by: Anders Hammarquist <iko@iko.pp.se>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We had the limit of 255 USB to serial devices on one system for almost
15 years, with no complaints. But now it's time to move on from these
tiny "baby" systems, and bump the number up to 512, which should last
us a few more years:
"512 is a nice number" -- Tobias Winter
Note, this is still a static value, and uses up tty core memory with
this many tty devices allocated. Converting the driver to use
TTY_DRIVER_DYNAMIC_DEV is the next thing to do in order to remove this
limitation.
Reported-by: Tobias Winter <tobias@linuxdingsda.de>
Tested-by: Tobias Winter <tobias@linuxdingsda.de>
Reviewed-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the allocation of minor device numbers from a static array to
be dynamic, using the idr interface. This means that you could
potentially get "gaps" in a minor number range for a single USB serial
device with multiple ports, but all should still work properly.
We remove the 'minor' field from the usb_serial structure, as it no
longer makes any sense for it (use the field in the usb_serial_port
structure if you really want to know this number), and take the fact
that we were overloading a number in this field to determine if we had
initialized the minor numbers or not, and just use a flag variable
instead.
Note, we still have the limitation of 255 USB to serial devices in the
system, as that is all we are registering with the TTY layer at this
point in time.
Tested-by: Tobias Winter <tobias@linuxdingsda.de>
Reviewed-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb_serial_port structure had the number field, which was the minor
number for the port, which almost no one really cared about. They
really wanted the number of the port within the device, which you had to
subtract from the minor of the parent usb_serial_device structure. To
clean this up, provide the real minor number of the port, and the number
of the port within the serial device separately, as these numbers might
not be related in the future.
Bonus is that this cleans up a lot of logic in the drivers, and saves
lines overall.
Tested-by: Tobias Winter <tobias@linuxdingsda.de>
Reviewed-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
--
drivers/staging/serqt_usb2/serqt_usb2.c | 21 +++--------
drivers/usb/serial/ark3116.c | 2 -
drivers/usb/serial/bus.c | 6 +--
drivers/usb/serial/console.c | 2 -
drivers/usb/serial/cp210x.c | 2 -
drivers/usb/serial/cypress_m8.c | 4 +-
drivers/usb/serial/digi_acceleport.c | 6 ---
drivers/usb/serial/f81232.c | 5 +-
drivers/usb/serial/garmin_gps.c | 6 +--
drivers/usb/serial/io_edgeport.c | 58 ++++++++++++--------------------
drivers/usb/serial/io_ti.c | 21 ++++-------
drivers/usb/serial/keyspan.c | 29 +++++++---------
drivers/usb/serial/metro-usb.c | 4 +-
drivers/usb/serial/mos7720.c | 37 +++++++++-----------
drivers/usb/serial/mos7840.c | 52 +++++++++-------------------
drivers/usb/serial/opticon.c | 2 -
drivers/usb/serial/pl2303.c | 2 -
drivers/usb/serial/quatech2.c | 7 +--
drivers/usb/serial/sierra.c | 2 -
drivers/usb/serial/ti_usb_3410_5052.c | 10 ++---
drivers/usb/serial/usb-serial.c | 7 ++-
drivers/usb/serial/usb_wwan.c | 2 -
drivers/usb/serial/whiteheat.c | 20 +++++------
include/linux/usb/serial.h | 6 ++-
24 files changed, 133 insertions(+), 180 deletions(-)
Do not use uninitialised termios data to determine when to configure the
device at open.
This also prevents stack data from leaking to userspace in the OOM error
path.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not use uninitialised termios data to determine when to configure the
device at open.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not use uninitialised termios data to determine when to configure the
device at open.
This also prevents stack data from leaking to userspace.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Per some ZTE Linux drivers I found for the AC2716, the following patch
moves most ZTE CDMA devices from option to zte_ev. The blacklist stuff
that option does is not required with zte_ev, because it doesn't
implement any of the send_setup hooks which the blacklist suppressed.
I did not move the 2718 over because I could not find any ZTE Linux
drivers for that device, nor even any Windows drivers.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mode used by Windows for the Huawei E1820 will use the
same ff/ff/ff class codes for both serial and network
functions.
Reported-by: Graham Inggs <graham.inggs@uct.ac.za>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When configuring the port (e.g. set_termios) the port minor number
rather than the port number was used in the request (and they only
coincide for minor number 0).
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix regression introduced by commit 143d9d9616 ("USB: serial: add
tiocmiwait subdriver operation") which made the ioctl operation return
ENODEV rather than ENOIOCTLCMD when a subdriver TIOCMIWAIT
implementation is missing.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The register access to enable hardware flow control depends on the
device port number and not the port minor number.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the no longer used endpoint-array access completely.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The outcont_endpoints array was indexed using the port minor number
(which can be greater than the array size) rather than the device port
number.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bogus port-number check in open and close, which prevented this
driver from being used with a minor number different from zero.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If you want to download Infineon modem via USB, this Infineon USB
flashloader driver is required.
Signed-off-by: Wei Shuai <cpuwolf@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Option GTM681W uses a qualcomm chip and can be
served by the qcserial device driver.
Signed-off-by: Richard Weinberger <richard@nod.at>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch adds a new HIDCOM device and does not affect other devices
driven by the cypress_M8 module. Changes are:
- add VendorID ProductID to device tables
- skip unstable speed check because FRWD uses 115200bps
- skip reset at probe which is an issue workaround for this
particular device.
Signed-off-by: Robert Butora <robert.butora.fi@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a specifier we may use to dump small buffers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The control-message timeout is specified in milliseconds and should not
depend on HZ.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The control and bulk-message timeouts are specified in milliseconds and
should not depend on HZ.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bulk-message timeout is specified in milliseconds and should not
depend on HZ.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The control-message timeout is specified in milliseconds and should not
depend on HZ.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix regression introduced by commit 0eafe4de1a ("USB: serial: mos7840:
add support for MCS7810 devices") which used stack-allocated buffers for
control messages.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The read_mos_reg function is called with stack-allocated buffers, which
must not be used for control messages.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The first and second interrupt-in urbs are swapped for some Treo/Kyocera
devices, but the urb context was never updated with the new port.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A rebranded Novatel E371 for AT&T's LTE bands.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'qt2_process_read_urb' is referenced only in this file. Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need to grab disconnect mutex in chars_in_buffer now that no
sub-driver is or should be querying hardware buffers anymore. (They
should use wait_until_sent.)
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new generic usb-serial wait_until_sent implementation to wait
for hardware buffers to drain.
This removes the need to check the hardware buffers in chars_in_buffer
and thus removes the overhead introduced by commit 2c992cd73 ("USB:
ti_usb_3410_5052: query hardware-buffer status in chars_in_buffer")
without breaking tty_wait_until_sent (used by, for example, tcdrain,
tcsendbreak and close).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new generic usb-serial wait_until_sent implementation to wait
for hardware buffers to drain.
This removes the need to check the hardware buffers in chars_in_buffer
and thus removes the overhead introduced by commit 263e1f9f ("USB:
io_ti: query hardware-buffer status in chars_in_buffer") without
breaking tty_wait_until_sent (used by, for example, tcdrain, tcsendbreak
and close).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new generic usb-serial wait_until_sent implementation to wait
for hardware buffers to drain.
This removes the need to check the hardware buffers in chars_in_buffer
and thus removes the overhead introduced by commit 6f602912 ("usb:
serial: ftdi_sio: Add missing chars_in_buffer function") without
breaking tty_wait_until_sent (used by, for example, tcdrain, tcsendbreak
and close).
Reported-by: Stas Sergeev <stsp@list.ru>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use usb-serial port rather than tty as argument to get_modem_status.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add generic wait_until_sent implementation which polls for empty
hardware buffers using the new port-operation tx_empty.
The generic implementation will be used for all sub-drivers that
implement tx_empty but does not define wait_until_sent.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add wait_until_sent operation which can be used to wait for hardware
buffers to drain.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big USB pull request for 3.10-rc1.
Lots of USB patches here, the majority being USB gadget changes and
USB-serial driver cleanups, the rest being ARM build fixes / cleanups,
and individual driver updates. We also finally got some chipidea fixes,
which have been delayed for a number of kernel releases, as the
maintainer has now reappeared.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlF+md4ACgkQMUfUDdst+ymkSgCfZWIiCtiX/li0yJqSiRB4yYJx
Ex0AoNemOOf6ywvSOHPbILTbJ1G+c/PX
=JmvB
-----END PGP SIGNATURE-----
Merge tag 'usb-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg Kroah-Hartman:
"Here's the big USB pull request for 3.10-rc1.
Lots of USB patches here, the majority being USB gadget changes and
USB-serial driver cleanups, the rest being ARM build fixes / cleanups,
and individual driver updates. We also finally got some chipidea
fixes, which have been delayed for a number of kernel releases, as the
maintainer has now reappeared.
All of these have been in linux-next for a while"
* tag 'usb-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (568 commits)
USB: ehci-msm: USB_MSM_OTG needs USB_PHY
USB: OHCI: avoid conflicting platform drivers
USB: OMAP: ISP1301 needs USB_PHY
USB: lpc32xx: ISP1301 needs USB_PHY
USB: ftdi_sio: enable two UART ports on ST Microconnect Lite
usb: phy: tegra: don't call into tegra-ehci directly
usb: phy: phy core cannot yet be a module
USB: Fix initconst in ehci driver
usb-storage: CY7C68300A chips do not support Cypress ATACB
USB: serial: option: Added support Olivetti Olicard 145
USB: ftdi_sio: correct ST Micro Connect Lite PIDs
ARM: mxs_defconfig: add CONFIG_USB_PHY
ARM: imx_v6_v7_defconfig: add CONFIG_USB_PHY
usb: phy: remove exported function from __init section
usb: gadget: zero: put function instances on unbind
usb: gadget: f_sourcesink.c: correct a copy-paste misnomer
usb: gadget: cdc2: fix error return code in cdc_do_config()
usb: gadget: multi: fix error return code in rndis_do_config()
usb: gadget: f_obex: fix error return code in obex_bind()
USB: storage: convert to use module_usb_driver()
...
The FT4232H used in the ST Micro Connect Lite has four hi-speed UART ports.
The first two ports are reserved for the JTAG interface.
We enable by default ports 2 and 3 as UARTs (where port 2 is a
conventional RS-232 UART)
Signed-off-by: Adrian Thomasset <adrian.thomasset@st.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current ST Micro Connect Lite uses the FT4232H hi-speed quad USB
UART FTDI chip. It is also possible to drive STM reference targets
populated with an on-board JTAG debugger based on the FT2232H chip with
the same STMicroelectronics tools.
For this reason, the ST Micro Connect Lite PIDs should be
ST_STMCLT_2232_PID: 0x3746
ST_STMCLT_4232_PID: 0x3747
Signed-off-by: Adrian Thomasset <adrian.thomasset@st.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kill custom closing_wait implementation and let the tty-layer handle it
instead.
Note that the port drain-delay is set to three characters to keep the
20ms delay after wait_until_sent at low baudrates (1200 baud) during close.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove redundant drain, which has already been handled by the tty-layer,
from break_ctl.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Query hardware-buffer status in chars_in_buffer should the write fifo be
empty.
This is needed to make the tty layer wait for hardware buffers to drain
on close.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The line status register is only polled so let's not keep a possibly
outdated value in the port data.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move write-fifo flushing from ti_drain to close where it belongs.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove redundant wait_until_sent, which has already been handled by the
tty-layer, from break_ctl.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix regression introduced by commit f40d78155 ("USB: io_ti: kill custom
closing_wait implementation") which made TIOCGSERIAL return the wrong
value for closing_wait.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org> # 3.9
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allocate port-private data in port-probe rather than in attach.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use port device for debug messages in interrupt-urb callback and remove
unused private data.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the port interrupt-in urb rather managing a private one.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device uses the second interrupt-in endpoint of the interface for
reading. Stop abusing the port read urb and store a pointer to the
second interrupt-in urb as port-private data instead.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the port interrupt-out urb rather than abusing the port write_urb
pointer and allocating a new urb at every open (but the first...).
Note that the write_urb abuse would have led to a double free should
there ever be interfaces with a bulk-out endpoint.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the more efficient generic read implementation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor read-urb processing, and add sanity checks on header and data
lengths.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove redundant data-offset define, which was really just the header
length.
Add payload-size define and use the bulk-out size define for the actual
bulk-out size.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clean up and fix typos in protocol comment.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure the port private data, which contains the write sequence
number, is cleared at allocation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes a sparse warning where we should be using NULL instead of 0
Cc: Wesley W. Terpstra <w.terpstra@gsi.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wishbone is an open hardware SoC bus commonly used in FPGA
designs. Bus access can be serialized using the Etherbone
protocol <http://www.ohwr.org/projects/etherbone-core>.
This driver is intended to be used with devices which attach
their internal Wishbone bus to a USB serial interface using
the Etherbone protocol. A userspace library is required to
speak the protocol made available by this driver as ttyUSBx.
Signed-off-by: Wesley W. Terpstra <w.terpstra@gsi.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes the depends on USB from all config symbols in
drivers/usb/host/Kconfig and replace that with an if USB / endif block
as suggested by Alan Stern. Some source ... Kconfig lines have been
shuffled around to permit a better regroupment of the Kconfig files
depending on "config USB" item. No functionnal change is introduced.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
![](/avatar/dabfd77a895665bf8b3c6da6e021895d?size=56 "Alexandr \\"Sky\\" Ivanov"){kind=small}
