In preparation of factoring out PCI_STATUS error bit handling let drivers
use the same collection of error bits. To facilitate bisecting we do this
in a separate patch per affected driver. For the Marvell drivers we have
to add PCI_STATUS_SIG_TARGET_ABORT to the error bits.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a spelling mistake in a dev_warn message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding ethtool stats for when XDP transmitted packets overrun the TX
queue. This is recorded separately for XDP_TX and ndo_xdp_xmit. This
is an important aid for troubleshooting XDP based setups.
It is currently a known weakness and property of XDP that there isn't
any push-back or congestion feedback when transmitting frames via XDP.
It's easy to realise when redirecting from a higher speed link into a
slower speed link, or simply two ingress links into a single egress.
The situation can also happen when Ethernet flow control is active.
For testing the patch and provoking the situation to occur on my
Espressobin board, I configured the TX-queue to be smaller (434) than
RX-queue (512) and overload network with large MTU size frames (as a
larger frame takes longer to transmit).
Hopefully the upcoming XDP TX hook can be extended to provide insight
into these TX queue overflows, to allow programmable adaptation
strategies.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently on the first check if the operation is still not
finished, the poll goes to sleep for 2-5 usecs. But if for
some reason (due to other priority stuff like interrupts etc) by
the time the poll wakes up the 10ms time is expired then we don't
check if operation is finished or not and return failure.
This patch modifies poll logic to check HW operation after sleep so
that the status is checked atleast twice.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bus mastering is enabled by firmware, but when this driver
is unbinded bus mastering gets disabled by the PCI subsystem
which results interrupts not working when driver is reloaded.
Hence set bus mastering everytime in probe().
Also
- Converted pci_set_dma_mask() and pci_set_consistent_dma_mask()
to dma_set_mask_and_coherent().
- Cleared transaction pending bit which gets set during
driver unbind due to clearing of bus mastering (ME bit).
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there is no way for AF dependent drivers in
any domain to check if the AF driver is loaded. This
patch sets an ID for RVUM block which will automatically
reflects in PF/VFs discovery register which they can
check and defer their probe until AF is up.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For retrieving info like interface MAC addresses, packet
parser key extraction config etc currently a command
is sent to firmware and firmware which periodically polls
for commands, processes these and returns the info.
This is resulting in interface initialization taking lot
of time. To optimize this a memory region is shared between
firmware and this driver, firmware while booting puts
static info like these into that region for driver to
read directly without using commands.
With this
- Logic for retrieving packet parser extraction config
via commands is removed and repalced with using the
shared 'fwdata' structure.
- Now RVU MSIX vector address is also retrieved from this fwdata struct
instead of from CSR. Otherwise when kexec/kdump crash kernel loads
CSR will have a IOVA setup by primary kernel which impacts
RVU PF/VF's interrupts.
- Also added a mbox handler for PF/VF interfaces to retrieve their MAC
addresses from AF.
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Christina Jacob <cjacob@marvell.com>
Signed-off-by: Rakesh Babu <rsaladi2@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added mailbox requests to retrieve backpressure IDs from AF and Aura,
CQ contexts are configured with these BPIDs. So that when resource
levels reach configured thresholds they assert backpressure on the
interface which is also mapped to same BPID.
Also added support to enable/disable pause frames generation via ethtool.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
CGX LMAC, the physical interface can generate pause frames when
internal resources asserts backpressure due to exhaustion.
This patch configures CGX to generate 802.3 pause frames.
Also enabled processing of received pause frames on the line which
will assert backpressure on the internal transmit path.
Also added mailbox handlers for PF drivers to enable or disable
pause frames anytime.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each of the interface receive channels can be backpressured by
resources upon exhaustion or reaching configured threshold levels.
Resources here are receive buffer queues (Auras) and pkt notification
descriptor queues (CQs). Resources and interface channels are mapped
using backpressure IDs (BPIDs).
HW supports upto 512 BPIDs, this patch divides these BPIDs statically
across CGX/LBK/SDP interfaces as follows.
BPIDs 0 - 191 are mapped to LMAC channels, 16 per LMAC.
BPIDs 192 - 255 are mapped to LBK channels.
BPIDs 256 - 511 are mapped to SDP channels.
Also did the needed basic configuration of BPIDs.
Added mbox handlers with which a PF device can request for a BPID which
it will use to configure Auras and CQs.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the Marvell mvpp2 ethernet driver to use the finalised link
parameters in mac_link_up() rather than the parameters in mac_config().
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the Marvell mvneta ethernet driver to use the finalised link
parameters in mac_link_up() rather than the parameters in mac_config().
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Propagate the resolved link parameters via the mac_link_up() call for
MACs that do not automatically track their PCS state. We propagate the
link parameters via function arguments so that inappropriate members
of struct phylink_link_state can't be accessed, and creating a new
structure just for this adds needless complexity to the API.
Tested-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Functions starting with __ usually indicate those which are exported,
but should not be called directly. Update some of those declared in the
API and make it more readable.
page_pool_unmap_page() and page_pool_release_page() were doing
exactly the same thing calling __page_pool_clean_page(). Let's
rename __page_pool_clean_page() to page_pool_release_page() and
export it in order to show up on perf logs and get rid of
page_pool_unmap_page().
Finally rename __page_pool_put_page() to page_pool_put_page() since we
can now directly call it from drivers and rename the existing
page_pool_put_page() to page_pool_put_full_page() since they do the same
thing but the latter is trying to sync the full DMA area.
This patch also updates netsec, mvneta and stmmac drivers which use
those functions.
Suggested-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce "rx" prefix in the name scheme for xdp counters
on rx path.
Differentiate between XDP_TX and ndo_xdp_xmit counters
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanedup repititive nixlf and blkaddr retrieving logic
is various mailbox handlers throughout the rvu_nix.c file.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the CGX register config is restricted to mapped RVU PFs,
this patch cleans up these permission checks spread across
the rvu_cgx.c file by moving the checks to a common fn().
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since CGX driver and AF driver are built into a single module
the export symbols in CGX driver are not needed. This patch
gets rid of them.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of xdp_ret in mvneta_swbm_rx_frame routine since now
we can rely on xdp_stats to flush in case of xdp_redirect
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add xdp_redirect, xdp_pass, xdp_drop and xdp_tx counters
to ethtool statistics
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce mvneta_stats structure in mvneta_update_stats routine signature
in order to collect all the rx stats and update them at the end at the
napi loop. mvneta_stats will be reused adding xdp statistics support to
ethtool.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In oreder to avoid unnecessary instructions rely on open-coding updating
per-cpu stats in mvneta_tx/mvneta_xdp_submit_frame and mvneta_rx_hwbm
routines. This patch will be used to add xdp support to ethtool for the
mvneta driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
mvneta_ethtool_update_stats routine is currently reporting
skb_alloc_error and refill_error only for the first rx queue.
Fix the issue moving skb_alloc_err and refill_err in
mvneta_pcpu_stats structure.
Moreover this patch will be used to introduce xdp statistics
to ethtool for the mvneta driver
Fixes: 17a96da627 ("net: mvneta: discriminate error cause for missed packet")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move rx_dropped and rx_errors counters in mvneta_pcpu_stats in order to
avoid possible races updating statistics
Fixes: 562e2f467e ("net: mvneta: Improve the buffer allocation method for SWBM")
Fixes: dc35a10f68 ("net: mvneta: bm: add support for hardware buffer management")
Fixes: c5aff18204 ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The otx2_mbox_get_rsp() function never returns NULL, it returns error
pointers on error.
Fixes: 34bfe0ebed ("octeontx2-pf: MTU, MAC and RX mode config support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In order to fix XDP support if sw buffer management is used as fallback
for hw bm devices, define MVNETA_SKB_HEADROOM as maximum between
XDP_PACKET_HEADROOM and NET_SKB_PAD and let the hw aligns the IP header
to 4-byte boundary.
Fix rx_offset_correction initialization if mvneta_bm_port_init fails in
mvneta_resume routine
Fixes: 0db51da7a8 ("net: mvneta: add basic XDP support")
Tested-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Add WireGuard
2) Add HE and TWT support to ath11k driver, from John Crispin.
3) Add ESP in TCP encapsulation support, from Sabrina Dubroca.
4) Add variable window congestion control to TIPC, from Jon Maloy.
5) Add BCM84881 PHY driver, from Russell King.
6) Start adding netlink support for ethtool operations, from Michal
Kubecek.
7) Add XDP drop and TX action support to ena driver, from Sameeh
Jubran.
8) Add new ipv4 route notifications so that mlxsw driver does not have
to handle identical routes itself. From Ido Schimmel.
9) Add BPF dynamic program extensions, from Alexei Starovoitov.
10) Support RX and TX timestamping in igc, from Vinicius Costa Gomes.
11) Add support for macsec HW offloading, from Antoine Tenart.
12) Add initial support for MPTCP protocol, from Christoph Paasch,
Matthieu Baerts, Florian Westphal, Peter Krystad, and many others.
13) Add Octeontx2 PF support, from Sunil Goutham, Geetha sowjanya, Linu
Cherian, and others.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1469 commits)
net: phy: add default ARCH_BCM_IPROC for MDIO_BCM_IPROC
udp: segment looped gso packets correctly
netem: change mailing list
qed: FW 8.42.2.0 debug features
qed: rt init valid initialization changed
qed: Debug feature: ilt and mdump
qed: FW 8.42.2.0 Add fw overlay feature
qed: FW 8.42.2.0 HSI changes
qed: FW 8.42.2.0 iscsi/fcoe changes
qed: Add abstraction for different hsi values per chip
qed: FW 8.42.2.0 Additional ll2 type
qed: Use dmae to write to widebus registers in fw_funcs
qed: FW 8.42.2.0 Parser offsets modified
qed: FW 8.42.2.0 Queue Manager changes
qed: FW 8.42.2.0 Expose new registers and change windows
qed: FW 8.42.2.0 Internal ram offsets modifications
MAINTAINERS: Add entry for Marvell OcteonTX2 Physical Function driver
Documentation: net: octeontx2: Add RVU HW and drivers overview
octeontx2-pf: ethtool RSS config support
octeontx2-pf: Add basic ethtool support
...
- remove ioremap_nocache given that is is equivalent to
ioremap everywhere
-----BEGIN PGP SIGNATURE-----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=TUCJ
-----END PGP SIGNATURE-----
Merge tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap
Pull ioremap updates from Christoph Hellwig:
"Remove the ioremap_nocache API (plus wrappers) that are always
identical to ioremap"
* tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap:
remove ioremap_nocache and devm_ioremap_nocache
MIPS: define ioremap_nocache to ioremap
Added support to show or configure RSS hash key, indirection table,
2,4 tuple via ethtool. Also added debug msg_level support
to dump messages when HW reports errors in packet received
or transmitted.
Signed-off-by: Prakash Brahmajyosyula <bprakash@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds ethtool support for
- Driver stats, Tx/Rx perqueue and CGX LMAC stats
- Set/show Rx/Tx queue count
- Set/show Rx/Tx ring sizes
- Set/show IRQ coalescing parameters
Signed-off-by: Christina Jacob <cjacob@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added ndo_get_stats64 which returns stats maintained by HW.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds TCP segmentation offload (TSO) support. First version
of the silicon didn't support TSO offload, for this driver
level TSO support is added.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds receive side scaling (RSS) support to distribute
pkts/flows across multiple queues. Sets up key, indirection
table etc. Also added extraction of HW calculated rxhash and
adding to same to SKB ie NETIF_F_RXHASH offload support.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW reports many errors on the receive and transmit paths.
Such as incorrect queue configuration, pkt transmission errors,
LMTST instruction errors, transmit queue full etc. These are reported
via QINT interrupt. Most of the errors are fatal and needs
reinitialization.
Also added support to allocate receive buffers in non-atomic context
when allocation fails in NAPI context.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Aleksey Makarov <amakarov@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addes support to change interface MTU, MAC address
retrieval and config, RX mode ie unicast, multicast and promiscuous.
Also added link loopback support
Signed-off-by: Tomasz Duszynski <tduszynski@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PF and AF (admin function) shares 64KB of reserved memory region for
communication. This region is shared for
- Messages sent by PF and responses sent by AF.
- Notifications sent by AF and ACKs sent by PF.
This patch adds infrastructure to handle notifications sent
by AF and adds handlers to process them.
One of the main usecase of notifications from AF is physical
link changes. So this patch adds registration of PF with AF
to receive link status change notifications and also adds
the handler for that notification.
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Tomasz Duszynski <tduszynski@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the packet transmission support.
For a given skb prepares send queue descriptors (SQEs) and pushes them
to HW. Here driver doesn't maintain it's own SQ rings, SQEs are pushed
to HW using a silicon specific operations called LMTST. From the
instuction HW derives the transmit queue number and queues the SQE to
that queue. These LMTST instructions are designed to avoid queue
maintenance in SW and lockless behavior ie when multiple cores are trying
to add SQEs to same queue then HW will takecare of serialization, no need
for SW to hold locks.
Also supports scatter/gather.
Co-developed-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added receive packet handling (NAPI) support, error stats, RX_ALL
capability config option to passon error pkts to stack upon user request.
In subsequent patches these error stats will be added to ethttool.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Completion queue (CQ) is the one with which HW notifies SW on a packet
reception or transmission. Each of the RQ and SQ are mapped to a unique
CQ and again both CQs are mapped to same interrupt ie the CINT. So that
each core has one interrupt source in whose handler both Rx and Tx
notifications are processed.
Also
- Registered a NAPI handler for the CINT.
- Setup coalescing parameters.
- IRQ affinity hints etc
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does the initialization of all queues ie the
receive buffer pools, receive and transmit queues, completion
or notification queues etc. Allocates all required resources
(eg transmit schedulers, receive buffers etc) and configures
them for proper functioning of queues. Also sets up receive
queue's RED dropping levels.
Co-developed-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For a PF to function as a NIC, NPA (for Rx buffers, Tx descriptors etc)
and NIX (for rcv, send and completion queues) are the minimum resources
needed. So request admin function (AF) to attach one each of NIX and NPA
block LFs (local functions).
Only AF can configure a LF's contexts, so request AF to allocate memory
for NPA aura/pool and NIX RQ/SQ/CQ HW contexts. Upon receiving response,
save some of the HW constants like number of pointers per stack page,
size of send queue buffer (SQBs, where SQEs are queued by HW) e.t.c which
are later used to initialize queues.
A HW context here is like a state machine maintained for a descriptor
queue. eg size, head/tail pointers, irq etc etc. HW maintains this in
memory.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the resource virtualization unit (RVU) each of the PF and AF
(admin function) share a 64KB of reserved memory region for
communication. This patch initializes PF <=> AF mailbox IRQs,
registers handlers for processing these communication messages.
Also adds support to process these messages in both directions
ie responses to PF initiated DOWN (PF => AF) messages and AF
initiated UP messages (AF => PF).
Mbox communication APIs and message formats are defined in AF driver
(drivers/net/ethernet/marvell/octeontx2/af), mbox.h from AF driver is
included here to avoid duplication.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Christina Jacob <cjacob@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Aleksey Makarov <amakarov@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds template for the Marvell's OcteonTX2 network
controller's physical function driver. Just the probe, PCI
specific initialization and netdev registration.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently XDP Support was added to the mvneta driver
for software buffer management only.
It is still possible to attach an XDP program if
hardware buffer management is used.
It is not doing anything at that point.
The patch disallows attaching XDP programs to mvneta
if hardware buffer management is used.
I am sorry about that. It is my first submission and I am having
some troubles with the format of my emails.
v4 -> v5:
- Remove extra tabs
v3 -> v4:
- Please ignore v3 I accidentally submitted
my other patch with git-send-mail and v4 is correct
v2 -> v3:
- My mailserver corrupted the patch
resubmission with git-send-email
v1 -> v2:
- Fixing the patches indentation
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first batch of driver conversions missed a few cases where we can
use phy_do_ioctl too.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Page pool API will start syncing (if requested) starting from
page->dma_addr + pool->p.offset. Fix dma sync length in
mvneta_run_xdp since we do not need to account xdp headroom
Fixes: 07e13edbb6 ("net: mvneta: get rid of huge dma sync in mvneta_rx_refill")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With 'commit 44768decb7 ("page_pool: handle page recycle for NUMA_NO_NODE
condition")' we can safely change nid to NUMA_NO_NODE and accommodate
future NUMA aware hardware using mvneta network interface
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
