This patch (commit 690a1f2002) added a
new call site for acpi_set_WOL() without checking that the function is
actually suitable to be called via
vortex_set_wol+0xcd/0xe0 [3c59x]
dev_ethtool+0xa5a/0xb70
dev_ioctl+0x2e0/0x4b0
T.961+0x49/0x50
sock_ioctl+0x47/0x290
do_vfs_ioctl+0x7f/0x340
sys_ioctl+0x80/0xa0
system_call_fastpath+0x16/0x1b
i.e. outside of code paths run when the device is not yet enabled or
already disabled. In particular, putting the device into D3hot is a
pretty bad idea when it was already brought up.
Furthermore, all prior callers of the function made sure they're
actually dealing with a PCI device, while the newly added one didn't.
In the same spirit, the .get_wol handler shouldn't indicate support
for WOL for non-PCI devices.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a bug introduced in commit
de84727214
"3c59x: Use fine-grained locks for MII and windowed register access".
vortex_interrupt() holds vp->window_lock over multiple register
accesses to reduce locking overhead. However it also needs to call
vortex_error() sometimes, and that uses the regular functions for
access to windowed registers, which will try to acquire window_lock
again.
Therefore, drop window_lock around the call to vortex_error() and set
the window afterward reacquiring the lock. Since vortex_error() may
call vortex_rx(), which *does* require its caller to hold window_lock,
lift that call up into vortex_interrupt(). This also removes the
potential for calling vortex_rx() on a later-generation NIC.
Reported-and-tested-by: Jens Schüßler <jgs@trash.net> [in Debian's 2.6.32]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
vortex_ioctl() was grabbing vortex_private::lock around its call to
generic_mii_ioctl(). This is no longer necessary since there are more
specific locks which the mdio_{read,write}() functions will obtain.
Worse, those functions do not save and restore IRQ flags when locking
the MII state, so interrupts will be enabled when generic_mii_ioctl()
returns.
Since there is currently no need for any function to call
mdio_{read,write}() while holding another spinlock, do not change them
to save and restore IRQ flags but remove the specification of ordering
between vortex_private::lock and vortex_private::mii_lock.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
If netconsole is in use, there is a possibility for deadlock in 3c59x between
boomerang_interrupt and boomerang_start_xmit. Both routines take the vp->lock,
and if netconsole is in use, a pr_* call from the boomerang_interrupt routine
will result in the netconsole code attempting to trnasmit an skb, which can try
to take the same spin lock, resulting in deadlock.
The fix is pretty straightforward. This patch allocats a bit in the 3c59x
private structure to indicate that its handling an interrupt. If we get into
the transmit routine and that bit is set, we can be sure that we have recursed
and will deadlock if we continue, so instead we just return NETDEV_TX_BUSY, so
the stack requeues the skb to try again later.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds wrappers for ethtool to get or set wake-on-LAN
setting without re-inserting the kernel module.
Signed-off-by: Andrew O. Shadoura <andrew@beldisplaytech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit a095cfc40e
"3c59x: Specify window explicitly for access to windowed registers"
changed the first parameter to mdio_sync(), from a pointer to the
register mapping, to a pointer to the vortex_private structure,
and changed all but one of the call sites. Fix that last one.
Reported-by: Luca Falavigna <dktrkranz@debian.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
If vortex_probe1() fails we should unmap ioaddr mapped earlier.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_iomap() can fail, handle this case and return -ENOMEM from probe
function.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This avoids scheduling in atomic context and also means that IRQs
will only be deferred for relatively short periods of time.
Previously discussed in:
http://article.gmane.org/gmane.linux.network/155024
Reported-by: Arne Nordmark <nordmark@mech.kth.se>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently much of the code assumes that a specific window has been
selected, while a few functions save and restore the window. This
makes it impossible to introduce fine-grained locking.
Make those assumptions explicit by introducing wrapper functions
to set the window and read/write a register. Use these everywhere
except vortex_interrupt(), vortex_start_xmit() and vortex_rx().
These set the window just once, or not at all in the case of
vortex_rx() as it should always be called from vortex_interrupt().
Cache the current window in struct vortex_private to avoid
unnecessary hardware writes.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Tested-by: Arne Nordmark <nordmark@mech.kth.se> [against 2.6.32]
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes from drivers/net/ all the unnecessary
return; statements that precede the last closing brace of
void functions.
It does not remove the returns that are immediately
preceded by a label as gcc doesn't like that.
It also does not remove null void functions with return.
Done via:
$ grep -rP --include=*.[ch] -l "return;\n}" net/ | \
xargs perl -i -e 'local $/ ; while (<>) { s/\n[ \t\n]+return;\n}/\n}/g; print; }'
with some cleanups by hand.
Compile tested x86 allmodconfig only.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Drivers can avoid one cache miss
(on dev->trans_start) in their start_xmit() handler.
Exceptions are NETIF_F_LLTX drivers
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
replaces (skb->len - skb->data_len) occurrences by skb_headlen(skb)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Use DEFINE_PCI_DEVICE_TABLE() so we get place PCI ids table into correct section
in every case.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only files where David Miller is the primary git-signer.
wireless, wimax, ixgbe, etc are not modified.
Compile tested x86 allyesconfig only
Not all files compiled (not x86 compatible)
Added a few > 80 column lines, which I ignored.
Existing checkpatch complaints ignored.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As noticed by Alan Stern, there is still one issue with the driver:
we disable PCI IRQ on suspend, but other devices on the same IRQ
line might still need the IRQ enabled to suspend properly.
Nowadays, PCI core handles all power management work by itself, with
one condition though: if we use dev_pm_ops. So, rework the driver to
only quiesce 3c59x internal logic on suspend, while PCI core will
manage PCI device power state with IRQs disabled.
Suggested-by: Rafael J. Wysocki <rjw@sisk.pl>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following trace pops up if we try to suspend with 3c59x ethernet NIC
brought down:
root@b1:~# ifconfig eth16 down
root@b1:~# echo mem > /sys/power/state
...
3c59x 0000:00:10.0: suspend
3c59x 0000:00:10.0: PME# disabled
Trying to free already-free IRQ 48
------------[ cut here ]------------
Badness at c00554e4 [verbose debug info unavailable]
NIP: c00554e4 LR: c00554e4 CTR: c019a098
REGS: c7975c60 TRAP: 0700 Not tainted (2.6.31-rc4)
MSR: 00021032 <ME,CE,IR,DR> CR: 28242422 XER: 20000000
TASK = c79cb0c0[1746] 'bash' THREAD: c7974000
...
NIP [c00554e4] __free_irq+0x108/0x1b0
LR [c00554e4] __free_irq+0x108/0x1b0
Call Trace:
[c7975d10] [c00554e4] __free_irq+0x108/0x1b0 (unreliable)
[c7975d30] [c005559c] free_irq+0x10/0x24
[c7975d40] [c01e21ec] vortex_suspend+0x70/0xc4
[c7975d60] [c017e584] pci_legacy_suspend+0x58/0x100
This is because the driver manages interrupts without checking for
netif_running().
Though, there are few other issues with suspend/resume in this driver.
The intention of calling free_irq() in suspend() was to avoid any
possible spurious interrupts (see commit 5b039e681b
"3c59x PM fixes"). But,
- On resume, the driver was requesting IRQ just after pci_set_master(),
but before vortex_up() (which actually resets 3c59x chips).
- Issuing free_irq() on a shared IRQ doesn't guarantee that a buggy
HW won't trigger spurious interrupts in another driver that
requested the same interrupt. So, if we want to protect from
unexpected interrupts, then on suspend we should issue disable_irq(),
not free_irq().
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We found this old card which was not supported, and physically
looks similar to the other 3C905B we have (9055).
After adding the IDs it seems to work fine (MII report, dhcp, scp, ...)
Acked-by: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following build failure with gcc 3.2:
CC [M] drivers/net/3c59x.o
drivers/net/3c59x.c:2726:1: directives may not be used inside a macro argument
drivers/net/3c59x.c:2725:59: unterminated argument list invoking macro "pr_err"
drivers/net/3c59x.c: In function `dump_tx_ring':
drivers/net/3c59x.c:2727: implicit declaration of function `pr_err'
drivers/net/3c59x.c:2731: syntax error before ')' token
Apparently gcc 3.2 doesn't like #if interleaved with a macro call.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is the result of an automatic spatch transformation to convert
all ndo_start_xmit() return values of 0 to NETDEV_TX_OK.
Some occurences are missed by the automatic conversion, those will be
handled in a seperate patch.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert magic values 1 and -1 to NETDEV_TX_BUSY and NETDEV_TX_LOCKED respectively.
0 (NETDEV_TX_OK) is not changed to keep the noise down, except in very few cases
where its in direct proximity to one of the other values.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since dev->power.should_wakeup bit is used by the PCI core to
decide whether the device should wake up the system from sleep
states, set this bit by calling device_set_wakeup_enable().
This restores proper WOL for the 3c59x driver.
Reported-and-tested-by: Graeme Wilford <gwilford@gmail.com>
Reported-by: Gunnar Degnbol <degnbol@danbbs.dk>
Signed-off-by: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have some reasons to kill netdev->priv:
1. netdev->priv is equal to netdev_priv().
2. netdev_priv() wraps the calculation of netdev->priv's offset, obviously
netdev_priv() is more flexible than netdev->priv.
But we cann't kill netdev->priv, because so many drivers reference to it
directly.
This patch is a safe convert for netdev->priv to netdev_priv(netdev).
Since all of the netdev->priv is only for read.
But it is too big to be sent in one mail.
I split it to 4 parts and make every part smaller than 100,000 bytes,
which is max size allowed by vger.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Drivers need not do it any more.
Some cases had to be skipped over because the drivers
were making use of the ->last_rx value themselves.
Signed-off-by: David S. Miller <davem@davemloft.net>
This converts pretty much everything to print_mac. There were
a few things that had conflicts which I have just dropped for
now, no harm done.
I've built an allyesconfig with this and looked at the files
that weren't built very carefully, but it's a huge patch.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix possible bug where end of receive buffer could be overwritten.
The allocation needs to allow for the reserved space. This would only happen
if device received packet greater than Ethernet standard MTU.
Change this driver to use netdev_alloc_skb rather than setting skb->dev
directly. For the initial allocation it doesn't need to be GFP_ATOMIC.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This changes vortex_prob1() to handle pci_name() now returning a
constant string.
Cc: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use net_device_stats from net_device structure instead of local.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Acked-by: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The ethernet card 3c980-TX needs a mdio_sync() to initialize the ethernet
properly. This is forced by adding an EXTRA_PREAMBLE to its drv_flags.
Without this, the driver did not reconnect after a link loss.
Signed-off-by: Gunnar Larisch <Gunnar.Larisch@gmx.de>
Acked-by: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Simple compile warning fix. (against 2.6.23-git12)
Thanks,
Badari
vortex_up() should initialize 'err' for a successful return.
drivers/net/3c59x.c: In function `vortex_up':
drivers/net/3c59x.c:1494: warning: `err' might be used uninitialized in this function
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some NICs (3c905B) can not generate PME in power state PCI_D0, while others
like 3c905C can. Call pci_enable_wake() with PCI_D3hot should give proper
WOL for 3c905B.
Signed-off-by: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Tested-by: Harry Coin <hcoin@n4comm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
These have been superceded by the new ->get_sset_count() hook.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's been a useless no-op for long enough in 2.6 so I figured it's time to
remove it. The number of people that could object because they're
maintaining unified 2.4 and 2.6 drivers is probably rather small.
[ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check return of pci_enable_device in vortex_up().
Also modify vortex_up to return error to callers. Handle failure of
vortex_up in vortex_open and vortex_resume.
Signed-off-by: Mark Hindley <mark@hindley.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A special sequence of ifconfig up/down and plug/unplug the cable can break
the duplex configuration of the driver.
Setting
vp->mii.full_duplex = vp->full_duplex
in vortex_up should fix this.
Addresses Bug 8575 3c59x duplex configuration broken
http://bugzilla.kernel.org/show_bug.cgi?id=8575
Cc: Martin Buck <mb-tmp-ohtmvyyn.xreary.bet@gromit.dyndns.org>
Signed-off-by: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Cc: Natalie Protasevich <protasnb@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
