The pixel clock rates were introduced to report the initially static clock
rate.
Since this is now handled dynamically, we can remove them entirely.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx6dq
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The MIPI divider is also cleared as part of the clock setup sequence, so we
can remove that code.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx6dq
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The OV5640_SCLK2X_ROOT_DIVIDER_DEFAULT and OV5640_SCLK_ROOT_DIVIDER_DEFAULT
defines represent exactly the same setup, and are at the same value, than
the more consistent with the rest of the driver OV5640_SCLK2X_ROOT_DIV and
OV5640_SCLK_ROOT_DIV.
Remove them.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx6dq
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Part of the hardcoded initialization sequence is to set up the proper clock
dividers. However, this is now done dynamically through proper code and as
such, the static one is now redundant.
Let's remove it.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx6dq
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The clock structure for the PCLK is quite obscure in the documentation, and
was hardcoded through the bytes array of each and every mode.
This is troublesome, since we cannot adjust it at runtime based on other
parameters (such as the number of bytes per pixel), and we can't support
either framerates that have not been used by the various vendors, since we
don't have the needed initialization sequence.
We can however understand how the clock tree works, and then implement some
functions to derive the various parameters from a given rate. And now that
those parameters are calculated at runtime, we can remove them from the
initialization sequence.
The modes also gained a new parameter which is the clock that they are
running at, from the register writes they were doing, so for now the switch
to the new algorithm should be transparent.
Co-Developed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Tested-by: Adam Ford <aford173@gmail.com> #imx6dq
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The set_fmt operations updates the sensor format only when the image format
is changed. When only the image sizes gets changed, the format do not get
updated causing the sensor to always report the one that was previously in
use.
Without this patch, updating frame size only fails:
[fmt:UYVY8_2X8/640x480@1/30 field:none colorspace:srgb xfer:srgb ...]
With this patch applied:
[fmt:UYVY8_2X8/1024x768@1/30 field:none colorspace:srgb xfer:srgb ...]
Fixes: 6949d86477 ("media: ov5640: do not change mode if format or frame interval is unchanged")
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx6 w/ CSI2 interface on 4.19.6 and 4.20-RC5
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The chip can be configured to output data transitions on the
rising or falling edge of PIXCLK (Datasheet R58:1[9]), default is on the
falling edge.
Parsing the fw-node is made in a subfunction to bundle all (future)
dt-parsing / fw-parsing stuff.
[m.grzeschik@pengutronix.de: Fix inverting clock. INV_PIX_CLOCK bit is set
per default. Set bit to 0 (enable mask bit without value) to enable
falling edge sampling.]
[m.felsch@pengutronix.de: use fwnode helpers]
[m.felsch@pengutronix.de: mv fw parsing into own function]
[m.felsch@pengutronix.de: adapt commit msg]
[sakari.ailus@linux.intel.com: V4L2 API usage changes to compile
on media tree master]
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch implements the framerate selection using the skipping and
readout power-modi features. The power-modi cut the framerate by half
and each context has an independent selection bit. The same applies to
the 2x skipping feature.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently set_fmt don't care about the streaming status, so the format
can be changed during streaming. This can lead into wrong behaviours.
Check if the device is already streaming and return -EBUSY to avoid
wrong behaviours.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add callback to check if we are already streaming. Now other callbacks
can check the state and return -EBUSY if we already streaming.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The imx274 driver uses regmap and the build will fail without it.
Fixes:
drivers/media/i2c/imx274.c:142:21: error: variable ‘imx274_regmap_config’ has initializer but incomplete type
static const struct regmap_config imx274_regmap_config = {
^~~~~~~~~~~~~
drivers/media/i2c/imx274.c:1869:19: error: implicit declaration of function ‘devm_regmap_init_i2c’ [-Werror=implicit-function-declaration]
imx274->regmap = devm_regmap_init_i2c(client, &imx274_regmap_config);
^~~~~~~~~~~~~~~~~~~~
and others.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2_ctrl_handler_init() expects a hint of how many controls this
handler is expected to refer to. Since this number here is always 4,
let's pass exactly 4.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
imx274_read_reg() takes a u8 pointer ("reg") and casts it to pass it
to regmap_read(), which takes an unsigned int pointer. This results in
a corrupted stack and random crashes.
Fixes: 0985dd306f ("media: imx274: V4l2 driver for Sony imx274 CMOS sensor")
Cc: stable@vger.kernel.org # for 4.15 and up
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Some Sony camera sensors have same test pattern
definitions, this patch unify the pattern naming
to make it more clear to the userspace.
Suggested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
current imx355 test pattern order in ctrl menu
is not correct, this patch fixes it.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
current imx319 test pattern order in ctrl menu
is not correct, this patch fixes it.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Commit 37c65802e76a ("media: tvp5150: Add sync lock interrupt handling")
introduced the interrupt handling. But we have to free the
v4l2_ctrl_handler before we can return the error code.
Fixes: 37c65802e76a ("media: tvp5150: Add sync lock interrupt handling")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There is a spelling mistake in the module description as well
as a comment. Fix them.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
On older Kernels (prior to 4.15) irqreturn_t and devm_request_threaded_irq
is not defined when compiling adv7604.c. It seems more recent Kernels
include it via another header which is included by adv7604.c.
Now we include linux/interrupt.h explicitly to get the type also defined
for Kernels prior to 4.15.
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The adv7180 produces 1 to 2 frames of garbage before proper sync is
established. This allows V4L2 drivers and apps to skip those.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Without CONFIG_HDMI, we get a link error for this driver:
drivers/media/i2c/tda1997x.o: In function `tda1997x_parse_infoframe':
tda1997x.c:(.text+0x2195): undefined reference to `hdmi_infoframe_unpack'
tda1997x.c:(.text+0x21b6): undefined reference to `hdmi_infoframe_log'
drivers/media/i2c/tda1997x.o: In function `tda1997x_log_infoframe':
tda1997x.c:(.text.unlikely+0x13d3): undefined reference to `hdmi_infoframe_unpack'
tda1997x.c:(.text.unlikely+0x1426): undefined reference to `hdmi_infoframe_log'
All other drivers in this directory that use HDMI select CONFIG_HDMI,
so do the same here:
Fixes: 9ac0038db9 ("media: i2c: Add TDA1997x HDMI receiver driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The v4l2_dv_timings_cap struct is used to do sanity checks when setting and
enumerating DV timings, ensuring that only valid timings as per the HW
capabilities are allowed.
However, many drivers just filled in 0 for the minimum width, height or
pixelclock frequency. This can cause timings with e.g. 0 as width and height
to be accepted, which will in turn lead to a potential division by zero.
Fill in proper values are minimum boundaries. 640x350 was chosen since it is
the smallest resolution in v4l2-dv-timings.h. Same for 13 MHz as the lowest
pixelclock frequency (it's slightly below the minimum of 13.5 MHz in the
v4l2-dv-timings.h header).
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The CEC IP is very similar between the three HDMI receivers, but
not identical. Add support for all three variants.
Tested with an adv7604 and an adv7612.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Swapping the order between v4l2 subdevice registration and checking chip
id in b7a417628a ("media: ov2680: don't register the v4l2 subdevice
before checking chip ID") makes the mode restore to use the sensor
controls before they are set, so move the mode restore call to s_power
after the handler setup for controls is done.
This remove also the need for the error code path in power on function.
Fixes: b7a417628a ("media: ov2680: don't register the v4l2 subdevice before checking chip ID")
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This adds log_status ioctl and event interface for ov7670's v4l2 controls.
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This adds log_status ioctl and event interface for ov5640's v4l2 controls.
Cc: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This adds log_status ioctl and event interface for ov2640's v4l2 controls.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ov2640 has the test pattern generator features. This makes use of
it through V4L2_CID_TEST_PATTERN control.
[Sakari Ailus: Use "Eight Vertical Colour Bars" as the second manu entry]
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The mt9m111 has special camera effects feature. This makes use of
it through V4L2_CID_COLORFX control.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This adds log_status ioctl and event interface for mt9m111's v4l2 controls.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
change bayer order when using test pattern mode.
remove test pattern mapping method
[Sakari Ailus: Drop extra added newline]
Signed-off-by: Chen, JasonX Z <jasonx.z.chen@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Clang warns when a variable is assigned to itself:
drivers/media/i2c/imx214.c:695:13: error: explicitly assigning value of
variable of type 'const struct reg_8 *' to itself
[-Werror,-Wself-assign]
for (table = table; table->addr != IMX214_TABLE_END ; table++) {
~~~~~ ^ ~~~~~
1 error generated.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The vb2_ops structure can be const as it is only stored in the ops
field of a vb2_queue structure and this field is const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
AMG88xx has a register for setting frame rate 1 or 10 FPS.
This adds support changing frame interval.
Reference specifications:
https://docid81hrs3j1.cloudfront.net/medialibrary/2017/11/PANA-S-A0002141979-1.pdf
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use regmap for i2c register access. This simplifies register accesses and
chooses suitable access commands based on the functionality that the
adapter supports.
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The video device release() callback for video-i2c driver frees the whole
struct video_i2c_data. If there is no user left for the video device
when video_unregister_device() is called, the release callback is executed.
However, in video_i2c_remove() some fields (v4l2_dev, lock, and queue_lock)
in struct video_i2c_data are still accessed after video_unregister_device()
is called.
This fixes the use after free by moving the code from video_i2c_remove()
to the release() callback.
Fixes: 5cebaac609 ("media: video-i2c: add video-i2c driver")
Reviewed-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The fields of a v4l2_subdev_ops structure are all const, so the
structures that are stored there and are not used elsewhere can be
const as well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The v4l2_ctrl_ops structure is only passed as the second argument to
functions such as v4l2_ctrl_new_std for which the corresponding
parameter is const, so make the v4l2_ctrl_ops structure const as well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a V4L2 sub-device driver for the Sony IMX214 image sensor.
This is a camera sensor using the I2C bus for control and the
CSI-2 bus for data.
Tested on a DB820c alike board with Intrinsyc Open-Q 13MP camera.
[Sakari Ailus: squash exposure time max limit patch]
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Clang warns when a variable is assigned to itself.
drivers/media/i2c/tc358743.c:1921:7: warning: explicitly assigning value
of variable of type 'int' to itself [-Wself-assign]
ret = ret;
~~~ ^ ~~~
1 warning generated.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Those drivers are part of the legacy SoC camera framework.
They're being converted to not use it, but sometimes we're
keeping both legacy any new driver.
This time, for example, we have two drivers on media with
the same name: ov772x. That's bad.
So, in order to prevent that to happen, let's prepend the SoC
legacy drivers with soc_.
No functional changes.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2_async_unregister_subdev() may not be called without
v4l2_async_register_subdev() being called first. Fix this.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If probe fails, the kernel will print the error code. There's no need to
driver to do that.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Fixed the case where v4l2_async_unregister_subdev()
is called unnecessarily in the error handling path
in probe function.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When there is no EDID the CEC adapter should be unconfigured as
well. So call cec_phys_addr_invalidate() when this happens.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.18 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When there is no EDID the CEC adapter should be unconfigured as
well. So call cec_phys_addr_invalidate() when this happens.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.18 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Changing framerate right before streamon had no effect,
the new framerate value was taken into account only at
next streamon, fix this.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
