TI AR7 Watchdog Timer is only build for 32bit.
Avoid error like:
In file included from drivers/watchdog/ar7_wdt.c:29:
./arch/mips/include/asm/mach-ar7/ar7.h: In function ‘ar7_is_titan’:
./arch/mips/include/asm/mach-ar7/ar7.h:111:24: error: implicit declaration of function ‘KSEG1ADDR’; did you mean ‘CKSEG1ADDR’? [-Werror=implicit-function-declaration]
111 | return (readl((void *)KSEG1ADDR(AR7_REGS_GPIO + 0x24)) & 0xffff) ==
| ^~~~~~~~~
| CKSEG1ADDR
Fixes: da2a68b3eb ("watchdog: Enable COMPILE_TEST where possible")
Signed-off-by: Jackie Liu <liuyun01@kylinos.cn>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210907024904.4127611-1-liu.yun@linux.dev
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
On existing SoCs, the watchdog has a single clock input: HOSC (OSC24M)
divided by 750. However, starting with R329, LOSC (OSC32k) is added as
an alternative clock source, with a bit to switch between them.
Since 24 MHz / 750 == 32 kHz, not 32.768 kHz, the hardware adjusts the
cycle counts to keep the timeouts independent of the clock source. This
keeps the programming interface backward-compatible.
Furthermore, the R329 has two watchdogs: one for use by the ARM CPUs
at 0x20000a0, and a second one for use by the DSPs at 0x7020400. The
first of these adds two more new registers, to allow software to
immediately assert the SoC reset signal. Add an additional "-reset"
suffix to signify the presence of this feature.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210902225750.29313-2-samuel@sholland.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Proper machine resets via da9062/da9063 PMICs are very tricky as they
require special i2c atomic transfers when interrupts are not available
anymore. This is also a reason why both PMIC's restart handlers do not
use regmap but instead opt for i2c_smbus_write_byte_data() which does
i2c transfer in atomic manner. Under the hood, this function tries to
obtain i2c bus lock with call to i2c_adapter_trylock_bus() which will
return -EAGAIN (-11) if lock is not available.
Since commit 982bb70517 ("watchdog: reset last_hw_keepalive time at
start") occasional restart handler failures with "Failed to shutdown
(err = -11)" error messages were observed, indicating that some
process is holding the i2c bus lock. Investigation into the matter
uncovered that sometimes during reboot sequence watchdog ping is issued
late into poweroff/reboot phase which did not happen before mentioned
commit (usually the watchdog ping happened immediately as commit message
suggests). As of now, when watchdog ping usually happens late into
poweroff/reboot stage when interrupts are not available anymore, i2c bus
lock cannot be released anymore and pending restart handler in turn
fails.
Thus, to prevent such late watchdog pings from happening ahead of
pending machine restart and consequently locking up the i2c bus, check
for system_state in watchdog ping handler and consequently do not send
pings anymore in case system_state > SYSTEM_RUNNING.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Link: https://lore.kernel.org/r/20210708082128.2832904-1-primoz.fiser@norik.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
While the driver will only match against a single device, convention is
to dynamically allocate the driver data.
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1baffdc410d6476cccffe9712cec56350335812a.1628525954.git-series.a.fatoum@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Driver so far wasn't ported to the driver model and registered
the watchdog device out of the init after probing the I/O ports
for a watchdog with correct vendor and device revision.
Keep the device detection part at init time, but move watchdog
registration to a platform driver probe function.
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/9e1088839662e5c357286cab0b9de0bb0602e4fd.1628525954.git-series.a.fatoum@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Migrating the driver lets us drop the watchdog misc device boilerplate
and reduces size by 285 lines. It also brings us support for new
functionality like CONFIG_WATCHDOG_HANDLE_BOOT_ENABLED.
This incurs a slight backwards-compatibility break, because the new
kernel watchdog API doesn't support unloading modules for drivers
whose watchdog hardware is reported to be running.
This means following scenario will be no longer supported:
- BIOS has enabled watchdog
- Module is loaded and unloaded without opening watchdog
- module_exit is expected to succeed and disable watchdog HW
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/35d9dbf57b58c5f003cef31dc256ec2fec044524.1628525954.git-series.a.fatoum@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Code for the common parts of the driver either uses watchdog_ as
prefix for the watchdog API or f71808e_ for everything else.
The driver now supports 9 more variants besides the f71808e,
so let's rename the common parts to start with fintek_wdt_ instead.
This makes code browsing easier, because it's readily apparent
that functions are not variant-specific. Some watchdog_-prefixed
functions remain, but these will be dropped altogether with the move
to the kernel watchdog API in a later commit.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/31805c6aeb8d161f852ddad7c32b91319f924988.1628525954.git-series.a.fatoum@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The fintek_wdt_names is meant for read-only use and is currently not
modified. Mark it const to catch future writes.
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/9720c5a1efcef861da68b693453bb3eb3c21af37.1628525954.git-series.a.fatoum@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
max_timeout never served any purpose over WATCHDOG_MAX_TIMEOUT, which it
was initialized with. Drop it.
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/d1f8cda90283855633537adee0af2c6b00a9ec25.1628525954.git-series.a.fatoum@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The fintek watchdog timer can configure timeouts of second granularity
only up to 255 seconds. Beyond that, the timeout needs to be configured
with minute granularity. WDIOC_GETTIMEOUT should report the actual
timeout configured, not just echo back the timeout configured by the
user. Do so.
Fixes: 96cb4eb019 ("watchdog: f71808e_wdt: new watchdog driver for Fintek F71808E and F71882FG")
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Link: https://lore.kernel.org/r/5e17960fe8cc0e3cb2ba53de4730b75d9a0f33d5.1628525954.git-series.a.fatoum@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
In the function stm32_iwdg_probe(), devm_platform_ioremap_resource
has already contained error message, so drop the redundant one.
Co-developed-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210814142741.7396-1-tangbin@cmss.chinamobile.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Cong Wang says:
====================
This patchset fixes ->poll() for sockets in sockmap and updates
selftests accordingly with select(). Please check each patch
for more details.
Fixes: c50524ec4e ("Merge branch 'sockmap: add sockmap support for unix datagram socket'")
Fixes: 89d69c5d0f ("Merge branch 'sockmap: introduce BPF_SK_SKB_VERDICT and support UDP'")
Acked-by: John Fastabend <john.fastabend@gmail.com>
---
v4: add a comment in udp_poll()
v3: drop sk_psock_get_checked()
reuse tcp_bpf_sock_is_readable()
v2: rename and reuse ->stream_memory_read()
fix a compile error in sk_psock_get_checked()
Cong Wang (3):
net: rename ->stream_memory_read to ->sock_is_readable
skmsg: extract and reuse sk_msg_is_readable()
net: implement ->sock_is_readable() for UDP and AF_UNIX
====================
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
We use non-blocking sockets in those tests, retrying for
EAGAIN is ugly because there is no upper bound for the packet
arrival time, at least in theory. After we fix poll() on
sockmap sockets, now we can switch to select()+recv().
Signed-off-by: Yucong Sun <sunyucong@gmail.com>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20211008203306.37525-5-xiyou.wangcong@gmail.com
Yucong noticed we can't poll() sockets in sockmap even
when they are the destination sockets of redirections.
This is because we never poll any psock queues in ->poll(),
except for TCP. With ->sock_is_readable() now we can
overwrite >sock_is_readable(), invoke and implement it for
both UDP and AF_UNIX sockets.
Reported-by: Yucong Sun <sunyucong@gmail.com>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20211008203306.37525-4-xiyou.wangcong@gmail.com
The proto ops ->stream_memory_read() is currently only used
by TCP to check whether psock queue is empty or not. We need
to rename it before reusing it for non-TCP protocols, and
adjust the exsiting users accordingly.
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20211008203306.37525-2-xiyou.wangcong@gmail.com
With two Msgs, msgA and msgB and a user doing nonblocking sendmsg calls (or
multiple cores) on a single socket 'sk' we could get the following flow.
msgA, sk msgB, sk
----------- ---------------
tcp_bpf_sendmsg()
lock(sk)
psock = sk->psock
tcp_bpf_sendmsg()
lock(sk) ... blocking
tcp_bpf_send_verdict
if (psock->eval == NONE)
psock->eval = sk_psock_msg_verdict
..
< handle SK_REDIRECT case >
release_sock(sk) < lock dropped so grab here >
ret = tcp_bpf_sendmsg_redir
psock = sk->psock
tcp_bpf_send_verdict
lock_sock(sk) ... blocking on B
if (psock->eval == NONE) <- boom.
psock->eval will have msgA state
The problem here is we dropped the lock on msgA and grabbed it with msgB.
Now we have old state in psock and importantly psock->eval has not been
cleared. So msgB will run whatever action was done on A and the verdict
program may never see it.
Fixes: 604326b41a ("bpf, sockmap: convert to generic sk_msg interface")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20211012052019.184398-1-liujian56@huawei.com
Use asm/unwind.h to implement wchan, since we cannot always rely on
STACKTRACE=y.
Fixes: bc9bbb8173 ("x86: Fix get_wchan() to support the ORC unwinder")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lkml.kernel.org/r/20211022152104.137058575@infradead.org
rpcif_sw_init() can fail so make sure we check the return value
of it and on error exit rpcif_spi_probe() callback with error code.
Fixes: eb8d6d464a ("spi: add Renesas RPC-IF driver")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20211025205631.21151-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
pm_runtime_disable() cancels all pending power requests, while they
should be completed for the Tegra SPI driver. Otherwise SPI clock won't
be disabled ever again because clk refcount will become unbalanced.
Enforce runtime PM suspension to put device into expected state before
driver is unbound and device's RPM state is reset by driver's core.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20211023225951.14253-2-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
pm_runtime_disable() cancels all pending power requests, while they
should be completed for the Tegra SPI driver. Otherwise SPI clock won't
be disabled ever again because clk refcount will become unbalanced.
Enforce runtime PM suspension to put device into expected state before
driver is unbound and device's RPM state is reset by driver's core.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20211023225951.14253-1-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the missing clk_disable_unprepare() before return
from bcm_qspi_probe() in the error handling case.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20211018073413.2029081-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Driver probe and remove were inconsistent in what they did to power-down
and neither did all steps. In addition to that, neither function
prevented the interrupt handler from running during and after power-down.
Richard Fitzgerald (2):
ASoC: cs42l42: Reset and power-down on remove() and failed probe()
ASoC: cs42l42: free_irq() before powering-down on probe() fail
sound/soc/codecs/cs42l42.c | 43 +++++++++++++++++++++++++++++++------------
1 file changed, 31 insertions(+), 12 deletions(-)
--
2.11.0
This patch set is to add support for lpass sc7280 based targets.
Upadate compatible name and change of bulk clock voting to optional
clock voting in digital codecs va, rx, tx macro drivers.
Changes Since V3:
-- Removed fixes tag.
-- Change signedoff by sequence.
Changes Since V2:
-- Add Tx macro deafults for lpass sc7280
Changes Since V1:
-- Removed individual clock voting and used bulk clock optional.
-- Removed volatile changes and fixed default values.
-- Typo errors.
Srinivasa Rao Mandadapu (5):
ASoC: qcom: Add compatible names in va,wsa,rx,tx codec drivers for
sc7280
ASoC: qcom: dt-bindings: Add compatible names for lpass sc7280 digital
codecs
ASoC: codecs: tx-macro: Enable tx top soundwire mic clock
ASoC: codecs: tx-macro: Update tx default values
ASoC: codecs: Change bulk clock voting to optional voting in digital
codecs
.../bindings/sound/qcom,lpass-rx-macro.yaml | 4 +++-
.../bindings/sound/qcom,lpass-tx-macro.yaml | 4 +++-
.../bindings/sound/qcom,lpass-va-macro.yaml | 4 +++-
.../bindings/sound/qcom,lpass-wsa-macro.yaml | 4 +++-
sound/soc/codecs/lpass-rx-macro.c | 3 ++-
sound/soc/codecs/lpass-tx-macro.c | 25 +++++++++++++++++++---
sound/soc/codecs/lpass-va-macro.c | 3 ++-
sound/soc/codecs/lpass-wsa-macro.c | 1 +
8 files changed, 39 insertions(+), 9 deletions(-)
--
Qualcomm India Private Limited, on behalf of Qualcomm Innovation Center, Inc.,
is a member of Code Aurora Forum, a Linux Foundation Collaborative Project.
Hi Mark,
This version is a respin of v10 fixing a build error in 12/17 patch.
QCOM SoC relevant non-audio patches in this series has been merged into
the Qualcomm drivers-for-5.16 tree, as this series depends those patches
an immutable tag is available at:
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux.gittags/20210927135559.738-6-srinivas.kandagatla@linaro.org
This patchset adds ASoC driver support to configure signal processing
framework ("AudioReach") which is integral part of Qualcomm next
generation audio SDK and will be deployed on upcoming Qualcomm chipsets.
It makes use of ASoC Topology to load graphs on to the DSP which is then
managed by APM (Audio Processing Manager) service to prepare/start/stop.
Here is simplified high-level block diagram of AudioReach:
___________________________________________________________
| CPU (Application Processor) |
| +---------+ +---------+ +----------+ |
| | q6apm | | q6apm | | q6apm | |
| | dais | <------> | | <-----> |lpass-dais| |
| +---------+ +---------+ +----------+ |
| ^ ^ |
| | | +---------+ |
| +---------+ v +---------->|topology | |
| | q6prm | +---------+ | | |
| | |<-------->| GPR | +---------+ |
| +---------+ +---------+ |
| ^ ^ |
| | | |
| +----------+ | |
| | q6prm | | |
| |lpass-clks| | |
| +----------+ | |
|____________________________|______________________________|
|
| RPMSG (IPC over GLINK)
____________________________|______________________________
| | |
| +-----------------------+ |
| | | |
| v v q6 (Audio DSP) |
|+-----+ +----------------------------------+ |
|| PRM | | APM (Audio Processing Manager) | |
|+-----+ | . Graph Management | |
| | . Command Handing | |
| | . Event Management | |
| | ... | |
| +----------------------------------+ |
| ^ |
|____________________________|______________________________|
|
| LPASS AIF
____________________________|______________________________
| | Audio I/O |
| v |
| +--------------------------------------------------+ |
| | Audio devices | |
| | CODEC | HDMI-TX | PCM | SLIMBUS | I2S |MI2S |...| |
| | | |
| +--------------------------------------------------+ |
|___________________________________________________________|
AudioReach has constructs of sub-graph, container and modules.
Each sub-graph can have N containers and each Container can have N Modules
and connections between them can be linear or non-linear.
An audio function can be realized with one or many connected
sub-graphs. There are also control/event paths between modules that can
be wired up while building graph to achieve various control mechanism
between modules. These concepts of Sub-Graph, Containers and Modules
are represented in ASoC topology.
Here is simple I2S graph with a Write Shared Memory and a
Volume control module within a single Subgraph (1) with one Container (1)
and 5 modules.
____________________________________________________________
| Sub-Graph [1] |
| _______________________________________________________ |
| | Container [1] | |
| | [WR_SH] -> [PCM DEC] -> [PCM CONV] -> [VOL]-> [I2S-EP]| |
| |_______________________________________________________| |
|____________________________________________________________|
For now this graph is split into two subgraphs to achieve dpcm like below:
________________________________________________ _________________
| Sub-Graph [1] | | Sub-Graph [2] |
| ____________________________________________ | | _____________ |
| | Container [1] | | | |Container [2]| |
| | [WR_SH] -> [PCM DEC] -> [PCM CONV] -> [VOL]| | | | [I2S-EP] | |
| |____________________________________________| | | |_____________| |
|________________________________________________| |_________________|
_________________
| Sub-Graph [3] |
| _____________ |
| |Container [3]| |
| | [DMA-EP] | |
| |_____________| |
|_________________|
This patchset adds very minimal support for AudioReach which includes
supporting sub-graphs containing CODEC DMA ports and simple PCM
Decoder/Encoder and Logger Modules. Additional capabilities will
be built over time to expose features offered by AudioReach.
This patchset is Tested on SM8250 SoC based Qualcomm Robotics Platform RB5
and SM9250 MTP with WSA881X Smart Speaker Amplifiers, DMICs connected via
VA Macro and WCD938x Codec connected via TX and RX Macro and HDMI audio
via I2S.
First 10 Patches are mostly reorganization existing Old QDSP Audio
Framework code and bindings so that we could reuse them on AudioReach.
ASoC topology graphs for DragonBoard RB5 and SM8250 MTP are available at
https://git.linaro.org/people/srinivas.kandagatla/audioreach-topology.git/
and Qualcomm AudioReach DSP headers are available at:
https://source.codeaurora.org/quic/la/platform/vendor/opensource/arspf-headers
Note: There is one false positive warning in this patchset:
audioreach.c:80:45: warning: array of flexible structures
Thanks,
srini
Changes since v10:
- fix build error during arm64 defconfig build reported by Mark in 12/17 patch
for audioreach_tplg_init symbol
Srinivas Kandagatla (17):
ASoC: dt-bindings: move LPASS dai related bindings out of q6afe
ASoC: dt-bindings: move LPASS clocks related bindings out of q6afe
ASoC: dt-bindings: rename q6afe.h to q6dsp-lpass-ports.h
ASoC: qdsp6: q6afe-dai: move lpass audio ports to common file
ASoC: qdsp6: q6afe-clocks: move audio-clocks to common file
ASoC: dt-bindings: q6dsp: add q6apm-lpass-dai compatible
ASoC: dt-bindings: lpass-clocks: add q6prm clocks compatible
ASoC: dt-bindings: add q6apm digital audio stream bindings
ASoC: qdsp6: audioreach: add basic pkt alloc support
ASoC: qdsp6: audioreach: add q6apm support
ASoC: qdsp6: audioreach: add module configuration command helpers
ASoC: qdsp6: audioreach: add Kconfig and Makefile
ASoC: qdsp6: audioreach: add topology support
ASoC: qdsp6: audioreach: add q6apm-dai support
ASoC: qdsp6: audioreach: add q6apm lpass dai support
ASoC: qdsp6: audioreach: add q6prm support
ASoC: qdsp6: audioreach: add support for q6prm-clocks
.../devicetree/bindings/sound/qcom,q6afe.txt | 181 ---
.../bindings/sound/qcom,q6apm-dai.yaml | 53 +
.../sound/qcom,q6dsp-lpass-clocks.yaml | 77 ++
.../sound/qcom,q6dsp-lpass-ports.yaml | 205 +++
include/dt-bindings/sound/qcom,q6afe.h | 203 +--
.../sound/qcom,q6dsp-lpass-ports.h | 208 +++
include/uapi/sound/snd_ar_tokens.h | 208 +++
sound/soc/qcom/Kconfig | 22 +
sound/soc/qcom/qdsp6/Makefile | 11 +-
sound/soc/qcom/qdsp6/audioreach.c | 1130 +++++++++++++++++
sound/soc/qcom/qdsp6/audioreach.h | 726 +++++++++++
sound/soc/qcom/qdsp6/q6afe-clocks.c | 187 +--
sound/soc/qcom/qdsp6/q6afe-dai.c | 687 +---------
sound/soc/qcom/qdsp6/q6apm-dai.c | 416 ++++++
sound/soc/qcom/qdsp6/q6apm-lpass-dais.c | 260 ++++
sound/soc/qcom/qdsp6/q6apm.c | 822 ++++++++++++
sound/soc/qcom/qdsp6/q6apm.h | 152 +++
sound/soc/qcom/qdsp6/q6dsp-lpass-clocks.c | 186 +++
sound/soc/qcom/qdsp6/q6dsp-lpass-clocks.h | 30 +
sound/soc/qcom/qdsp6/q6dsp-lpass-ports.c | 627 +++++++++
sound/soc/qcom/qdsp6/q6dsp-lpass-ports.h | 22 +
sound/soc/qcom/qdsp6/q6prm-clocks.c | 85 ++
sound/soc/qcom/qdsp6/q6prm.c | 202 +++
sound/soc/qcom/qdsp6/q6prm.h | 78 ++
sound/soc/qcom/qdsp6/topology.c | 1113 ++++++++++++++++
25 files changed, 6664 insertions(+), 1227 deletions(-)
create mode 100644 Documentation/devicetree/bindings/sound/qcom,q6apm-dai.yaml
create mode 100644 Documentation/devicetree/bindings/sound/qcom,q6dsp-lpass-clocks.yaml
create mode 100644 Documentation/devicetree/bindings/sound/qcom,q6dsp-lpass-ports.yaml
create mode 100644 include/dt-bindings/sound/qcom,q6dsp-lpass-ports.h
create mode 100644 include/uapi/sound/snd_ar_tokens.h
create mode 100644 sound/soc/qcom/qdsp6/audioreach.c
create mode 100644 sound/soc/qcom/qdsp6/audioreach.h
create mode 100644 sound/soc/qcom/qdsp6/q6apm-dai.c
create mode 100644 sound/soc/qcom/qdsp6/q6apm-lpass-dais.c
create mode 100644 sound/soc/qcom/qdsp6/q6apm.c
create mode 100644 sound/soc/qcom/qdsp6/q6apm.h
create mode 100644 sound/soc/qcom/qdsp6/q6dsp-lpass-clocks.c
create mode 100644 sound/soc/qcom/qdsp6/q6dsp-lpass-clocks.h
create mode 100644 sound/soc/qcom/qdsp6/q6dsp-lpass-ports.c
create mode 100644 sound/soc/qcom/qdsp6/q6dsp-lpass-ports.h
create mode 100644 sound/soc/qcom/qdsp6/q6prm-clocks.c
create mode 100644 sound/soc/qcom/qdsp6/q6prm.c
create mode 100644 sound/soc/qcom/qdsp6/q6prm.h
create mode 100644 sound/soc/qcom/qdsp6/topology.c
--
2.21.0
TI's implementation does not service the watchdog even if the kernel
command line parameter omap_wdt.early_enable is set to 1. This patch
fixes the issue.
Signed-off-by: Walter Stoll <walter.stoll@duagon.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/88a8fe5229cd68fa0f1fd22f5d66666c1b7057a0.camel@duagon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The MODULE_DEVICE_TABLE already creates proper alias for platform
driver. Having another MODULE_ALIAS causes the alias to be duplicated.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210917092024.19323-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
SBSA says of the generic watchdog:
All registers are 32 bits in size and should be accessed using 32-bit
reads and writes. If an access size other than 32 bits is used then
the results are IMPLEMENTATION DEFINED.
and for qemu, the implementation will only allow 32-bit accesses
resulting in a synchronous external abort when configuring the watchdog.
Use lo_hi_* accessors rather than a readq/writeq.
Fixes: abd3ac7902 ("watchdog: sbsa: Support architecture version 1")
Signed-off-by: Jamie Iles <quic_jiles@quicinc.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Link: https://lore.kernel.org/r/20210903112101.493552-1-quic_jiles@quicinc.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
This reverts commit cb011044e3 ("watchdog: iTCO_wdt: Account for
rebooting on second timeout") and commit aec42642d9 ("watchdog: iTCO_wdt:
Fix detection of SMI-off case") since those patches cause a regression
on certain boards (https://bugzilla.kernel.org/show_bug.cgi?id=213809).
While this revert may result in some boards to only reset after twice
the configured timeout value, that is still better than a watchdog reset
after half the configured value.
Fixes: cb011044e3 ("watchdog: iTCO_wdt: Account for rebooting on second timeout")
Fixes: aec42642d9 ("watchdog: iTCO_wdt: Fix detection of SMI-off case")
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Mantas Mikulėnas <grawity@gmail.com>
Reported-by: Javier S. Pedro <debbugs@javispedro.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20211008003302.1461733-1-linux@roeck-us.net
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
ARM_QCOM_SPM_CPUIDLE can be selected when compile-testing on
other architectures, but this causes a Kconfig warning
for QCOM_SPM:
WARNING: unmet direct dependencies detected for QCOM_SPM
Depends on [n]: ARCH_QCOM [=n]
Selected by [y]:
- ARM_QCOM_SPM_CPUIDLE [=y] && CPU_IDLE [=y] && (ARM [=y] || ARM64) && (ARCH_QCOM [=n] || COMPILE_TEST [=y]) && !ARM64 && MMU [=y]
Make it possible to also compile-test this one, which can
be done now that v5.15-rc5 lets you select QCOM_SCM everywhere.
Fixes: a871be6b8e ("cpuidle: Convert Qualcomm SPM driver to a generic CPUidle driver")
Fixes: 498ba2a8a2 ("cpuidle: Fix ARM_QCOM_SPM_CPUIDLE configuration")
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Driver uses already twice the same string literal.
Define it in one place, so every user will have this
name consistent.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211025135148.53944-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of putting garbage in the data structure, assign allocated id
or an error code to a temporary variable. This makes code cleaner.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211025135148.53944-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Data may be stored in DMA RX buffer, when suspending. The data needs
to be pushed to the upper layer. We can't rely on the timeout IRQ (RTOR)
that can't be triggered into low power state. So safely clear DMA request
(DMAR), force the DMA reception routines to push RX buffer content, before
disabling RX DMA. This way, handover to pio mode is safe.
Only call tty_flip_buffer_push() when there is RX data to handle.
Move the locking outside of stm32_usart_receive_chars() to prevent a race
condition, when disabling DMA request upon suspend / pm_runtime_suspend.
Data may be received under IRQ and pushed before
stm32_usart_receive_chars() has pushed older data from DMA rx_buf upon
suspend.
The sequence in suspend routine needs proper locking to avoid this.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20211025134229.8456-4-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DMA prevents the system to suspend when an UART RX wake-up source is
using DMA. DMA can't suspend while DMA channels are still active.
Terminate DMA transfer at suspend, and restart a new DMA transfer at
resume. Create stm32_usart_start_rx_dma_cyclic function to factorize
dma RX initialization. Move RX DMA code related to wakeup into
stm32_usart_serial_en_wakeup() routine to ease further improvements
on wakeup from low power modes.
Don't enable/disable wakeup on uninitialized port.
There may be data residue in the RX FIFO while suspending. Flush it at
suspend time. Receiver timeout interrupt won't trigger later in low power
mode, so call stm32_usart_receive_chars() in case there's data to handle.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20211025134229.8456-3-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The RX DMA channel is kept active forever (from the probe). That prevents
going to low power mode when it is used. This change moves the
DMA configuration and enabling procedures to startup routine to allow
transition to low power mode.
The DMA disabling procedure is implemented in stop_rx routine as this
ops has to stop characters reception, and DMA transation in shutdown.
Clean useless dma_async_tx_descriptor initialization to NULL value.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20211025134229.8456-2-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
revert commit 46ae40b94d ("net/mlx5: Let user configure io_eq_size param")
revert commit a6cb08daa3 ("net/mlx5: Let user configure event_eq_size param")
revert commit 5546040619 ("net/mlx5: Let user configure max_macs param")
The EQE parameters are applicable to more drivers, they should
be configured via standard API, probably ethtool. Example of
another driver needing something similar:
https://lore.kernel.org/all/1633454136-14679-3-git-send-email-sbhatta@marvell.com/
The last param for "max_macs" is probably fine but the documentation
is severely lacking. The meaning and implications for changing the
param need to be stated.
Link: https://lore.kernel.org/r/20211026152939.3125950-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
xilinx_uartps .start_tx() clears TXEMPTY when enabling TXEMPTY to avoid
any previous TXEVENT event asserting the UART interrupt. This clear
operation is done immediately after filling the TX FIFO.
However, if the bytes inserted by cdns_uart_handle_tx() are consumed by
the UART before the TXEMPTY is cleared, the clear operation eats the new
TXEMPTY event as well, causing cdns_uart_isr() to never receive the
TXEMPTY event. If there are bytes still queued in circbuf, TX will get
stuck as they will never get transferred to FIFO (unless new bytes are
queued to circbuf in which case .start_tx() is called again).
While the racy missed TXEMPTY occurs fairly often with short data
sequences (e.g. write 1 byte), in those cases circbuf is usually empty
so no action on TXEMPTY would have been needed anyway. On the other
hand, longer data sequences make the race much more unlikely as UART
takes longer to consume the TX FIFO. Therefore it is rare for this race
to cause visible issues in general.
Fix the race by clearing the TXEMPTY bit in ISR *before* filling the
FIFO.
The TXEMPTY bit in ISR will only get asserted at the exact moment the
TX FIFO *becomes* empty, so clearing the bit before filling FIFO does
not cause an extra immediate assertion even if the FIFO is initially
empty.
This is hard to reproduce directly on a normal system, but inserting
e.g. udelay(200) after cdns_uart_handle_tx(port), setting 4000000 baud,
and then running "dd if=/dev/zero bs=128 of=/dev/ttyPS0 count=50"
reliably reproduces the issue on my ZynqMP test system unless this fix
is applied.
Fixes: 85baf542d5 ("tty: xuartps: support 64 byte FIFO size")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Link: https://lore.kernel.org/r/20211026102741.2910441-1-anssi.hannula@bitwise.fi
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CONSOLE_POLL=n, CONFIG_SERIAL_SUNZILOG_CONSOLE=n, and CONFIG_SERIO=m:
drivers/tty/serial/sunzilog.c:1128:13: error: ‘sunzilog_putchar’ defined but not used [-Werror=unused-function]
1128 | static void sunzilog_putchar(struct uart_port *port, int ch)
| ^~~~~~~~~~~~~~~~
Fix this by marking sunzilog_putchar() __maybe_unused.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20211026080426.2444756-1-geert@linux-m68k.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In cases when functions are called via fwnode operations,
we already know that this is software node we are dealing
with, hence no need to check if it's NULL, it can't be,
Reported-by: YE Chengfeng <cyeaa@connect.ust.hk>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211026162954.89811-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
