To allow drivers to implement per-interface testmode operations
more easily, pass a wdev pointer if any identification for one
was given from userspace. Clean up the code a bit while at it.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Clean up the CQM settings code a bit and while at it
enforce that when setting the threshold to 0 (disable)
the hysteresis is also set to 0 to avoid confusion.
As we haven't enforce it, simply override userspace.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To allow channel switch announcements within beacons, add
the channel switch command to nl80211/cfg80211. This is
implementation is intended for AP and (later) IBSS mode.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is similar to the race Linus had reported, but in this case
it's an older bug: nl80211_prepare_wdev_dump() uses the wiphy
index in cb->args[0] as it is and thus parses the message over
and over again instead of just once because 0 is the first valid
wiphy index. Similar code in nl80211_testmode_dump() correctly
offsets the wiphy_index by 1, do that here as well.
Cc: stable@vger.kernel.org
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Whether the wiphy supports it or not is already checked, so what is left
is to enable these channel types.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
To allow scanning and working with 5 MHz and 10 MHz BSS, extend the
inform bss commands and add wrappers to take 5 and 10 MHz bss into
account.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
In most cases, host that receives IPv4 and IPv6 multicast/broadcast
packets does not do anything with these packets. Therefore the
reception of these unwanted packets causes unnecessary processing
and power consumption.
Packet coalesce feature helps to reduce number of received
interrupts to host by buffering these packets in firmware/hardware
for some predefined time. Received interrupt will be generated when
one of the following events occur.
a) Expiration of hardware timer whose expiration time is set to
maximum coalescing delay of matching coalesce rule.
b) Coalescing buffer in hardware reaches it's limit.
c) Packet doesn't match any of the configured coalesce rules.
This patch adds set/get configuration support for packet coalesce.
User needs to configure following parameters for creating a coalesce
rule.
a) Maximum coalescing delay
b) List of packet patterns which needs to be matched
c) Condition for coalescence. pattern 'match' or 'no match'
Multiple such rules can be created.
This feature needs to be advertised during driver initialization.
Drivers are supposed to do required firmware/hardware settings based
on user configuration.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
[fix kernel-doc, change free function, fix copy/paste error]
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Currently packet patterns and it's enum/structures are used only
for WoWLAN feature. As we intend to reuse them for new feature
packet coalesce, they are renamed in this patch.
Older names are kept for backward compatibility purpose.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
RSSI threshold value used for mesh peering should be in
negative value. After range checks to mesh parameters is
introduced, this is not allowed. Fix this.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
These two events were sent to the default network
namespace.
This caused AP mode in a non-default netns to not
work correctly. Mgmt tx status was multicasted to
a different (default) netns instead of the one the
AP was in.
Cc: stable@vger.kernel.org
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/wireless/ath/ath9k/Kconfig
drivers/net/xen-netback/netback.c
net/batman-adv/bat_iv_ogm.c
net/wireless/nl80211.c
The ath9k Kconfig conflict was a change of a Kconfig option name right
next to the deletion of another option.
The xen-netback conflict was overlapping changes involving the
handling of the notify list in xen_netbk_rx_action().
Batman conflict resolution provided by Antonio Quartulli, basically
keep everything in both conflict hunks.
The nl80211 conflict is a little more involved. In 'net' we added a
dynamic memory allocation to nl80211_dump_wiphy() to fix a race that
Linus reported. Meanwhile in 'net-next' the handlers were converted
to use pre and post doit handlers which use a flag to determine
whether to hold the RTNL mutex around the operation.
However, the dump handlers to not use this logic. Instead they have
to explicitly do the locking. There were apparent bugs in the
conversion of nl80211_dump_wiphy() in that we were not dropping the
RTNL mutex in all the return paths, and it seems we very much should
be doing so. So I fixed that whilst handling the overlapping changes.
To simplify the initial returns, I take the RTNL mutex after we try
to allocate 'tb'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid parsing the original dump message again and again by
allocating a small state struct that is used by the functions
involved in the dump, storing this struct in cb->args[0].
This reduces the memory allocation size as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merge mac80211 to avoid conflicts with the nl80211 attrbuf
changes.
Conflicts:
net/mac80211/iface.c
net/wireless/nl80211.c
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since my commit 3713b4e364 ("nl80211: allow splitting wiphy
information in dumps"), nl80211_dump_wiphy() uses the global
nl80211_fam.attrbuf for parsing the incoming data. This wouldn't
be a problem if it only did so on the first dump iteration which
is locked against other commands in generic netlink, but due to
space constraints in cb->args (the needed state doesn't fit) I
decided to always parse the original message. That's racy though
since nl80211_fam.attrbuf could be used by some other parsing in
generic netlink concurrently.
For now, fix this by allocating a separate parse buffer (it's a
bit too big for the stack, currently 1448 bytes on 64-bit). For
-next, I'll change the code to parse into the global buffer in
the first round only and then allocate a smaller buffer to keep
the data in cb->args.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add defines for 5 and 10 MHz channel width and fix channel
handling functions accordingly.
Also check for and report the WIPHY_FLAG_SUPPORTS_5_10_MHZ
capability.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
[fix spelling in comment]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
only the attributes are required and not the whole netlink info, as the
function accesses the attributes only anyway. This makes it easier to
parse nested beacon IEs later.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In two wiphy dump error cases, most often when the dump allocation
must be increased, the RTNL is leaked. This quickly results in a
complete system lockup. Release the RTNL correctly.
Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Users may want to send a frame on the current channel
without specifying it.
This is particularly useful for the correct implementation
of the IBSS/RSN support in wpa_supplicant which requires to
receive and send AUTH frames.
Make mgmt_tx pass a NULL channel to the driver if none has
been specified by the user.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
I (Johannes) accidentally applied the first version of the patch
("Allow TDLS peer AID to be configured for VHT"). Now apply just
the changes between v1 and v2 to get the AID verification and
prefer the new attribute over the old one.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently mesh uses mandatory rates as the default basic rates. Allow basic
rates to be configured during mesh join. Basic rates are applied only if
channel is also provided with mesh join command.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
[some whitespace fixes, refuse basic rates w/o channel]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a STA has a peer that it hasn't seen any tx activity
from for a certain length of time, the peer link is
expired. This means the inactive STA is removed from the
list of peers and that STA is not considered a peer again
unless it re-peers. Previously, this inactivity time was
always 30 minutes. Now, add it to the mesh configuration
and allow it to be configured. Retain 30 minutes as a
default value.
Signed-off-by: Colleen Twitty <colleen@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current internal SME implementation in cfg80211 is
very mixed up with the MLME handling, which has been
causing issues for a long time. There are three things
that the implementation has to provide:
* a basic SME implementation for nl80211's connect()
call (for drivers implementing auth/assoc, which is
really just mac80211) and wireless extensions
* MLME events for the userspace SME
* SME events (connected, disconnected etc.) for all
different SME implementation possibilities (driver,
cfg80211 and userspace)
To achieve these goals it isn't necessary to track the
software SME's connection status outside of it's state
(which is the part that caused many issues.) Instead,
track it only in the SME data (wdev->conn) and in the
general case only track whether the wdev is connected
or not (via wdev->current_bss.)
Also separate the internal implementation to not have
callbacks from the SME events, but rather call it from
the API functions that the driver (or rather mac80211)
calls. This separates the code better.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Do some cleanups in the cfg80211 SME APIs, which are
only used by mac80211.
Most of these functions get a frame passed, and there
isn't really any reason to export multiple functions
as cfg80211 can check the frame type instead, do that.
Additionally, the API functions have confusing names
like cfg80211_send_...() which was meant to indicate
that it sends an event to userspace, but gets a bit
confusing when there's both TX and RX and they're not
all clearly labeled.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
genlmsg_end() can't return an error since it returns the
skb length so remove checks treating the return value as
an error code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to take up the space for devices that don't
support WoWLAN, and most drivers can even make the support
data static const (except where it's modified at runtime.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
An active monitor interface is one that is used for communication (via
injection). It is expected to ACK incoming unicast packets. This is
useful for running various 802.11 testing utilities that associate to an
AP via injection and manage the state in user space.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make the current WoWLAN configuration available to drivers
at runtime. This isn't really useful for the normal WoWLAN
behaviour and accessing it can also be racy, but drivers
may use it for testing the WoWLAN device behaviour while
the host stays up & running to observe the device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
By making all the API functions require wdev locking we
can clean up the API a bit, getting rid of the locking
version of each function. This also decreases the size
of cfg80211 by a small amount.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
By making all the API functions require wdev locking we
can clean up the API a bit, getting rid of the locking
version of each function. This also decreases the size
of cfg80211 by a small amount.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Virtually all code paths in cfg80211 already (need to) hold
the RTNL. As such, there's little point in having another
four mutexes for various parts of the code, they just cause
lock ordering issues (and much of the time, the RTNL and a
few of the others need thus be held.)
Simplify all this by getting rid of the extra four mutexes
and just use the RTNL throughout. Only a few code changes
were needed to do this and we can get rid of a work struct
for bonus points.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
VHT uses peer AID in the PARTIAL_AID field in TDLS frames. The current
design for TDLS is to first add a dummy STA entry before completing TDLS
Setup and then update information on this STA entry based on what was
received from the peer during the setup exchange.
In theory, this could use NL80211_ATTR_STA_AID to set the peer AID just
like this is used in AP mode to set the AID of an association station.
However, existing cfg80211 validation rules prevent this attribute from
being used with set_station operation. To avoid interoperability issues
between different kernel and user space version combinations, introduce
a new nl80211 attribute for the purpose of setting TDLS peer AID. This
attribute can be used in both the new_station and set_station
operations. It is not supposed to be allowed to change the AID value
during the lifetime of the STA entry, but that validation is left for
drivers to do in the change_station callback.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Copy & paste mistake - STATION_INFO_TX_BYTES64 is the name of the flag,
not NL80211_STA_INFO_TX_BYTES64.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Authentication takes place in userspace, but the beacon is
generated in the kernel. Allow userspace to inform the
kernel of the authentication method so the appropriate
mesh config IE can be set prior to beacon generation when
joining the MBSS.
Signed-off-by: Colleen Twitty <colleen@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To support auto-loading of wireless modules from netlink users, add module
alias for nl80211 family.
This also adds NL80211_GENL_NAME constant to define the "nl80211" netlink
family name as part of uapi.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code sending the current WoWLAN TCP wakeup settings in
nl80211_send_wowlan_tcp() is not closing the nested attribute,
thus causing the parser to get confused on the receiver side
in userspace (iw). Fix this.
Cc: stable@vger.kernel.org [3.9]
Reported-by: Deepak Arora <deepakx.arora@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Adding the attributes fixes an issue with P2P Device not
working properly for management frame TX.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some protocols need a more reliable connection to complete
successful in reasonable time. This patch adds a user-space
API to indicate the wireless driver that a critical protocol
is about to commence and when it is done, using nl80211 primitives
NL80211_CMD_CRIT_PROTOCOL_START and NL80211_CRIT_PROTOCOL_STOP.
There can be only on critical protocol session started per
registered cfg80211 device.
The driver can support this by implementing the cfg80211 callbacks
.crit_proto_start() and .crit_proto_stop(). Examples of protocols
that can benefit from this are DHCP, EAPOL, APIPA. Exactly how the
link can/should be made more reliable is up to the driver. Things
to consider are avoid scanning, no multi-channel operations, and
alter coexistence schemes.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211_stop_p2p_device() requires the devlist_mtx to
be held, but nl80211_stop_p2p_device() doesn't acquire
it which is a locking error and causes a warning (when
lockdep is enabled). Fix this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Most dump callbacks, including the scan results one, use
the netdev to identify what to do, which is incorrect for
the P2P_DEVICE support, it needs to be able to get the
scan result from the wdev. Change all dumps to unify the
code, but ones other than scan don't really support being
executed on a wdev that has no netdev.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a P2P device wdev is removed while it has a scan, then the
scan completion might crash later as it is already freed by
that time. To avoid the crash always check the scan completion
when the P2P device is being removed for some reason. If the
driver already canceled it, don't want and free it, otherwise
warn and leak it to avoid later crashes.
In order to do this, locking needs to be changed away from the
rdev mutex (which can't always be guaranteed). For now, use
the sched_scan_mtx instead, I'll rename it to just scan_mtx in
a later patch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the user requested a userspace MPM, automatically
disable auto_open_plinks to fully disable the kernel MPM.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The mesh station types used to refer to whether the
station was secure or nonsecure. Really the salient
information is whether it is managed by the kernel or
userspace
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Secure mesh had the implicit requirement that the Mesh
Peering Management entity be in userspace. However
userspace might want to implement an open MPM as well, so
specify a mesh setup parameter to indicate this.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no reason TDLS should be prevented on P2P client
interfaces, and most of the code already handles it, so
allow adding stations for it.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add NL80211_CMD_UPDATE_FT_IES to support update of FT IEs to the WLAN
driver and NL80211_CMD_FT_EVENT to send FT events from the WLAN driver.
This will carry the target AP's MAC address along with the relevant
Information Elements. This event is used to report received FT IEs
(MDIE, FTIE, RSN IE, TIE, RICIE). These changes allow FT to be supported
with drivers that use an internal SME instead of user space option (like
FT implementation in wpa_supplicant with mac80211-based drivers).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It's not useful to specify a 0 keepalive interval, this
would send too much data. Prohibit this to also avoid
device issues.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211_mlme_assoc() has grown far too many arguments,
make the caller build almost all of the driver struct
and pass that to the function instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For testing it's sometimes useful to be able to
override certain VHT capability advertisement,
add the ability to do that in cfg80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is the sort of thing gcc's LTO could do, but since
we don't have that yet we can also do it manually. The
advantage is reduced code, both source and binary, e.g.
on x86-64
text data bss dec hex filename
442825 56230 776 499831 7a077 cfg80211.ko (before)
441585 56230 776 498591 79b9f cfg80211.ko (after)
a reduction of ~1k.
But in order to not complicate the code move only those
functions that are simple wrappers, not those that have
functionality of their own.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add back the channel width and extended capability data
to wiphy information if split information is supported.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add back the previously removed TCP WoWLAN information,
but only if userspace is prepared to deal with large
wiphy capability data dumps.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If userspace is updated to deal with large split wiphy
information dumps, add back the radar information that
could otherwise push the data over the limit of the
netlink dump messages.
Cc: Simon Wunderlich <simon.wunderlich@s2003.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The per-wiphy information is getting large, to the point
where with more than the typical number of channels it's
too large and overflows, and userspace can't get any of
the information at all.
To address this (in a way that doesn't require making all
messages bigger) allow userspace to specify that it can
deal with wiphy information split across multiple parts
of the dump, and if it can split up the data. This also
splits up each channel separately so an arbitrary number
of channels can be supported.
Additionally, since GET_WIPHY has the same problem, add
support for filtering the wiphy dump and get information
for a single wiphy only, this allows userspace apps to
use dump in this case to retrieve all data from a single
device.
As userspace needs to know if all this this is supported,
add a global nl80211 feature set and include a bit for
this behaviour in it.
Cc: Dennis H Jensen <dennis.h.jensen@siemens.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The station change API isn't being checked properly before
drivers are called, and as a result it is difficult to see
what should be allowed and what not.
In order to comprehensively check the API parameters parse
everything first, and then have the driver call a function
(cfg80211_check_station_change()) with the additionally
information about the kind of station that is being changed;
this allows the function to make better decisions than the
old code could.
While at it, also add a few checks, particularly in mesh
and clarify the TDLS station lifetime in documentation.
To be able to reduce a few checks, ignore any flag set bits
when the mask isn't set, they shouldn't be applied then.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make the ability to leave the plink_state unchanged not use a
magic -1 variable that isn't in the enum, but an explicit change
flag; reject invalid plink states or actions and move the needed
constants for plink actions to the right header file. Also
reject plink_state changes for non-mesh interfaces.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Given a device with many channels capabilities the wiphy
information can still overflow even though its size in
3.9 was reduced to 3.8 levels. For new userspace and
kernel 3.10 we're going to implement a new "split dump"
protocol that can use multiple messages per wiphy.
For now though, add a workaround to be able to send more
information to userspace. Since generic netlink doesn't
have a way to set the minimum dump size globally, and we
wouldn't really want to set it globally anyway, increase
the size only when needed, as described in the comments.
As userspace might not be prepared for large buffers, we
can only use 4k.
Also increase the size for the get_wiphy command.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is another case of data increasing the size of the
wiphy information significantly with a new feature, for
now remove this as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Just like the radar information, the TCP WoWLAN capability
data can increase the wiphy information and make it too
big. Remove the TCP WoWLAN information; no driver supports
it and new userspace tools will be required as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The wiphy information is getting very close to being too
much for a typical netlink dump message and adding the
radar attributes to channels and interface combinations
can push it over the limit, which means userspace gets no
information whatsoever. Therefore, remove these again for
now, no driver actually supports radar detection anyway
and a modified userspace is required as well.
We're working on a solution that will allow userspace to
request splitting the information across multiple netlink
messages, which will allow us to add this back.
Cc: Simon Wunderlich <simon.wunderlich@s2003.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Larry noticed (and bisected) that commit df881293c6
"cfg80211: Pass TDLS peer's QoS/HT/VHT information during set_station"
broke secure connections. This is is the case only for drivers that
don't support TDLS, where any kind of change, even just the change of
authorized flag that is required for normal operation, was rejected
now. To fix this, remove the checks. I have some patches that will add
proper verification for all the different cases later.
Cc: Jouni Malinen <j@w1.fi>
Bisected-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The information of the peer's capabilities is required for the driver
to perform TDLS Peer UAPSD operations. This information of the peer is
passed by the supplicant using NL80211_CMD_SET_STATION command. This
commit enhances the function nl80211_set_station to pass this
information of the peer to the driver in case this command is used
with the TDLS peer STA.
In addition, make the HT/VHT capability configuration handled more
consistently for other STA cases (reject both instead of just HT).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The information of the peer's capabilities and extended capabilities are
required for the driver to perform TDLS Peer UAPSD operations and off
channel operations. This information of the peer is passed from user space
using NL80211_CMD_SET_STATION command. This commit enhances
the function nl80211_set_station to pass the capability information of
the peer to the driver.
Similarly, there may be need for capability information for other modes,
so allow this to be provided with both add_station and change_station.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In many cases, userspace may need to know which of the
802.11 extended capabilities ("Extended Capabilities
element") are implemented in the driver or device, to
include them e.g. in beacons, assoc request/response
or other frames. Add a new nl80211 attribute to hold
the extended capabilities bitmap for this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When drivers or regulatory have limitations on
40, 80 or 160 MHz channels, advertise these to
userspace via nl80211. Also add a new feature
flag to let userspace know this is supported.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add new NL80211_CMD_RADAR_DETECT, which starts the Channel
Availability Check (CAC). This command will also notify the
usermode about events (CAC finished, CAC aborted, radar
detected, NOP finished).
Once radar detection has started it should continuously
monitor for radars as long as the channel is active.
This patch enables DFS for AP mode in nl80211/cfg80211.
Based on original patch by Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
[remove WIPHY_FLAG_HAS_RADAR_DETECT again -- my mistake]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Intel Wireless devices are able to make a TCP connection
after suspending, sending some data and waking up when
the connection receives wakeup data (or breaks). Add the
WoWLAN configuration and feature advertising API for it.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If user knows the location of a wowlan pattern to be matched in
Rx packet, he can provide an offset with the pattern. This will
help drivers to ignore initial bytes and match the pattern
efficiently.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
[refactor pattern sending]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
While technically the TSF isn't an IE, it can be
necessary to distinguish between the TSF from a
beacon and a probe response, in particular in
order to know the next DTIM TBTT, as not all APs
are spec compliant wrt. TSF==0 being a DTIM TBTT
and thus the DTIM count needs to be taken into
account as well.
To allow this, move the TSF into the IE struct
so it can be known whence it came.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In per-station statistics, present 32bit counters are too small
for practical purposes - with gigabit speeds, it get overlapped
every few seconds.
Expand counters in the struct station_info to be 64-bit.
Driver can still fill only 32-bit and indicate in @filled
only bits like STATION_INFO_[TR]X_BYTES; in case driver provides
full 64-bit counter, it should also set in @filled
bit STATION_INFO_[TR]RX_BYTES64
Netlink sends both 32-bit and 64-bit counters, if present, to not
break userspace.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
[change to also have 32-bit counters if driver advertises 64-bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When waking up from WoWLAN, it is useful to know
what triggered the wakeup. Support reporting the
wakeup reason(s) in cfg80211 (and a pass-through
in mac80211) to allow userspace to know.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add API to enable drivers to implement MAC address based
access control in AP/P2P GO mode. Capable drivers advertise
this capability by setting the maximum number of MAC
addresses in such a list in wiphy->max_acl_mac_addrs.
An initial ACL may be given to the NL80211_CMD_START_AP
command and/or changed later with NL80211_CMD_SET_MAC_ACL.
Black- and whitelists are supported, but not simultaneously.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
[rewrite commit log, many cleanups]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To ease further DFS development regarding interface combinations, use
the interface combinations structure to test for radar capabilities.
Drivers can specify which channel widths they support, and in which
modes. Right now only a single AP interface is allowed, but as the
DFS code evolves other combinations can be enabled.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The NL80211_ATTR_USE_MFP attribute was originally added for
NL80211_CMD_ASSOCIATE, but it is actually as useful (if not even more
useful) with NL80211_CMD_CONNECT, so process that attribute with the
connect command, too.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As per email discussion Jouni Malinen pointed out that:
"P2P message exchanges can be executed on the current operating channel
of any operation (both P2P and non-P2P station). These can be on 5 GHz
and even on 60 GHz (so yes, you _can_ do GO Negotiation on 60 GHz).
As an example, it would be possible to receive a GO Negotiation Request
frame on a 5 GHz only radio and then to complete GO Negotiation on that
band. This can happen both when connected to a P2P group (through client
discoverability mechanism) and when connected to a legacy AP (assuming
the station receive Probe Request frame from full scan in the beginning
of P2P device discovery)."
This means that P2P messages can be sent over different radio devices.
However, these should use the same P2P device address so it should be
able to provision this from user-space. This patch adds a parameter for
this to struct vif_params which should only be used during creation of
the P2P device interface.
Cc: Jouni Malinen <j@w1.fi>
Cc: Greg Goldman <ggoldman@broadcom.com>
Cc: Jithu Jance <jithu@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
[add error checking]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the nl80211_mesh_power_mode enumeration which holds possible
values for the mesh power mode. These modes are unknown, active,
light sleep and deep sleep.
Add power_mode entry to the mesh config structure to hold the
user-configured default mesh power mode. This value will be used
for new peer links.
Add the dot11MeshAwakeWindowDuration value to the mesh config.
The awake window is a duration in TU describing how long the STA
will stay awake after transmitting its beacon in PS mode.
Add access routines to:
- get/set local link-specific power mode (STA)
- get remote STA's link-specific power mode (STA)
- get remote STA's non-peer power mode (STA)
- get/set default mesh power mode (mesh config)
- get/set mesh awake window duration (mesh config)
All config changes may be done at mesh runtime and take effect
immediately.
Signed-off-by: Marco Porsch <marco@cozybit.com>
Signed-off-by: Ivan Bezyazychnyy <ivan.bezyazychnyy@gmail.com>
Signed-off-by: Mike Krinkin <krinkin.m.u@gmail.com>
[fix commit message line length, error handling in set station]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move the default mesh beacon interval and DTIM period to cfg80211
and make them accessible to nl80211. This enables setting both
values when joining an MBSS.
Previously the DTIM parameter was not set by mac80211 so the
driver's default value was used.
Signed-off-by: Marco Porsch <marco@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ranges are taken from IEEE 802.11-2012, common sense or current
implementation requirements.
Signed-off-by: Marco Porsch <marco@cozybit.com>
Acked-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The following changes are invalid and should be
disallowed when a station already exists:
* supported rates changes, except for TDLS peers
* listen interval changes
* HT capability changes
Disallow them and also update a mac80211 comment
explaining how they would be racy.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Today, stations are added already associated. That is
inefficient if, for example, the driver has no room
for stations any more because then the station will
go through the entire auth/assoc handshake, only to
be kicked out afterwards.
To address this a bit better, at least with drivers
using the new station state callback, allow hostapd
to add stations in unauthenticated mode, just after
receiving the AUTH frame, before even replying. Thus
if there's no more space at that point, it can send
a negative auth frame back. It still needs to handle
later state transition errors though, of course.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To simplify the locking and not require cfg80211_mutex
(which nl80211 uses to access the global regdomain) and
also to make it possible for drivers to access their
wiphy->regd safely, use RCU to protect these pointers.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's a bug with the world regulatory domain, it
can be updated any time which is different from all
other regdomains that can only be updated once after
a request for them. Fix this by adding a check for
"processed" to the reg_is_valid_request() function
and clear that when doing a request.
While looking at this I also found another locking
bug, last_request is protected by the reg_mutex not
the cfg80211_mutex so the code in nl80211 is racy.
Remove that code as it only tries to prevent an
allocation in an error case, which isn't necessary.
Then the function can also become static and locking
in nl80211 can have a smaller scope.
Also change __set_regdom() to do the checks earlier
and not different for world/other regdomains.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This code is a bit too BUG_ON happy, remove all
instances and while doing so make some code a bit
smarter by passing the right pointer instead of
indices into arrays.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is pretty much useless since get_wiphy_idx()
always returns true since it's always called with
a valid wiphy pointer.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Clean up various things like indentation, extra
parentheses, too many/few line breaks, etc.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a BSS struct is updated, the IEs are currently
overwritten or freed. This can lead to races if some
other CPU is accessing the BSS struct and using the
IEs concurrently.
Fix this by always allocating the IEs in a new struct
that holds the data and length and protecting access
to this new struct with RCU.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is a standalone if, seems to be a regression of commit
"nl80211/cfg80211: add VHT MCS support".
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The CQM TX-error rate/interval can't be less than
zero since they're unsigned values, remove checks.
Also fix indentation of the function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
