As clang points out, the vht_pfr is assigned to a struct member
without being initialized in one case:
drivers/net/wireless/ath/ath10k/mac.c:7528:7: error: variable 'vht_pfr' is used uninitialized whenever 'if' condition
is false [-Werror,-Wsometimes-uninitialized]
if (!ath10k_mac_can_set_bitrate_mask(ar, band, mask,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/ath/ath10k/mac.c:7551:20: note: uninitialized use occurs here
arvif->vht_pfr = vht_pfr;
^~~~~~~
drivers/net/wireless/ath/ath10k/mac.c:7528:3: note: remove the 'if' if its condition is always true
if (!ath10k_mac_can_set_bitrate_mask(ar, band, mask,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/ath/ath10k/mac.c:7483:12: note: initialize the variable 'vht_pfr' to silence this warning
u8 vht_pfr;
Add an explicit but probably incorrect initialization here.
I suspect we want a better fix here, but chose this approach to
illustrate the issue.
Fixes: 8b97b055dc ("ath10k: fix failure to set multiple fixed rate")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes checkpatch warnings:
drivers/net/wireless/ath/ath10k/pci.c:926: unnecessary cast may hide bugs, see http://c-faq.com/malloc/mallocnocast.html
drivers/net/wireless/ath/ath10k/pci.c:1072: unnecessary cast may hide bugs, see http://c-faq.com/malloc/mallocnocast.html
While at it, also remove unnecessary initialisation of data_buf variable in both cases.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes checkpatch warning:
drivers/net/wireless/ath/ath10k/swap.c:110: Possible unnecessary 'out of memory' message
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The workqueue need to flush and destory while remove sdio module,
otherwise it will have thread which is not destory after remove
sdio modules.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k will receive some message with invalid peer id from firmware.
reason is:
There are incoming frames to MAC hardware that NOT find relative
address search table, then peer id is invalid set by MAC hardware,
it is hardware's logic, so fix it in ath10k will be more convenient.
log:
ath10k_sdio mmc1:0001:1: Got RX ind from invalid peer: 65535
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently the memory allocated for qmi handle is
not being freed during de-init which leads to memory leak.
Free the allocated qmi memory in qmi deinit
to avoid memory leak.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1
Fixes: fda6fee0001e ("ath10k: add QMI message handshake for wcn3990 client")
Signed-off-by: Dundi Raviteja <dundi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It report error message while suspend/resume test.
dmesg log:
[ 150.749962] ath10k_sdio mmc1:0001:1: hif read32 not supported
[ 150.755728] ath10k_sdio mmc1:0001:1: failed to set coverage class: expected integer microsecond value in register
Reason is sdio chip does not support set_coverage_class as well as
pcie chip, remove the set_coverage_class handler will avoid it.
callstack of the error message:
OUTLINED_FUNCTION_6+0xc/0x14 [ath10k_core]
ath10k_mac_op_set_coverage_class+0x2c/0x40 [ath10k_core]
ieee80211_reconfig+0x5d0/0x108c [mac80211]
ieee80211_resume+0x34/0x6c [mac80211]
wiphy_resume+0xbc/0x13c [cfg80211]
dpm_run_callback+0xa4/0x168
device_resume+0x1d4/0x200
async_resume+0x1c/0x34
async_run_entry_fn+0x48/0xf8
process_one_work+0x178/0x2f8
worker_thread+0x1d8/0x2cc
kthread+0x11c/0x12c
ret_from_fork+0x10/0x18
the error log will not happen after this patch applied.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit ec8f24b7fa ("treewide: Add SPDX license identifier -
Makefile/Kconfig") marked various Makefiles and Kconfig files within ath
directories as GPL-2.0. But these modules and drivers are actually ISC:
* ath
* ar5523
* ath10k
* ath5k
* ath6kl
* ath9k
* wcn36xx
* wil6210
Fix SPDX tags accordingly.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Integrated WiFi chipset ex:WCN399x supports fw logging
using WMI copy engine and shared mem DIAG based fw logging.
By default shared mem DIAG based fw logging is enabled.
To support WMI copy engine based fw logging add QMI
control message to enable WMI copy engine based fw logging.
Enable WMI based fw logging using fw_diag_log module parameter.
insmod ath10k_core.ko fw_diag_log=1
DIAG utility(https://github.com/andersson/diag) implements extraction
of diagnostics related messages between application processor and
various subsystems while shared mem DIAG based fw logging is enabled.
Testing: Tested on WCN3990/QCA6174 HW
Tested FW: WLAN.HL.3.1-00959-QCAHLSWMTPLZ-1
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware will report flag with HTT_RX_IND_MPDU_STATUS_TKIP_MIC_ERR
if MIC error, the flag will be used in mac80211.
ieee80211_rx_h_michael_mic_verify will check the flag and start TKIP
countermeasures.
Now countermeasure tests pass both with WPA only and WPA2/WPA mixed
mode.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch will add the support to control the transmit power for traffic
to a station associated with the AP.
Underlying firmware will enforce that the maximum tx power will be based
on the regulatory requirements. If the user given transmit power is greater
than the allowed tx power in the given channel, then the firmware will use
the maximum tx power in the same channel.
Max and Min tx power values will depends on no of tx chain masks,
for QCA9984 allowed tx power range values from 6 to 23.
When 0 is sent to the firmware as tx power, it will revert to the default
tx power for the station.
Tested Hardware : QCA9984
Tested Firmware : 10.4-3.9.0.2-00046
Co-developed-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Ashok Raj Nagarajan <arnagara@codeaurora.org>
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Peer creation in firmware fails if last peer deletion is still
in progress.
The firmware sends a peer delete response event if it advertises
the service WMI_SERVICE_SYNC_DELETE_CMDS. This peer delete response
event is used to synchronize the peer deletion.
Add peer delete response event and wait for the event after
deleting every peer from host driver to synchronize with firmware.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Dundi Raviteja <dundi@codeaurora.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When we add an interface immediately after removing
the interface the vdev deletion in firmware might not
have been completed. We need to synchronize the vdev creation
with the firmware.
Wait for vdev delete response from firmware when we
remove an interface.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Observed PCIE device wake up failed after ~120 iterations of
soft-reboot test. The error message is
"ath10k_pci 0000:01:00.0: failed to wake up device : -110"
The call trace as below:
ath10k_pci_probe -> ath10k_pci_force_wake -> ath10k_pci_wake_wait ->
ath10k_pci_is_awake
Once trigger the device to wake up, we will continuously check the RTC
state until it returns RTC_STATE_V_ON or timeout.
But for QCA99x0 chips, we use wrong value for RTC_STATE_V_ON.
Occasionally, we get 0x7 on the fist read, we thought as a failure
case, but actually is the right value, also verified with the spec.
So fix the issue by changing RTC_STATE_V_ON from 0x5 to 0x7, passed
~2000 iterations.
Tested HW: QCA9984
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, below fixed rate commands are broken,
iw wlanx set bitrates legacy-<2.4|5> ht-mcs-<2.4|5> vht-mcs-<2.4|5> \
<NSS:MCSx>
iw wlanx set bitrates legacy-<2.4|5> <legacy rate> ht-mcs-<2.4|5> \
vht-mcs-<2.4|5> <NSS:MCSx>
There are two methods to set fixed rate, both failed,
- Use vdev fixed rate command
This command only support one single rate, but it's broken due to
mac80211 change commit e8e4f5280d ("mac80211: reject/clear user
rate mask if not usable"), which requires user to specify at least
one legacy rate. So we can't use this command to set ht/vht single
rate any more.
- Use peer_assoc command
This command can update rx capability for multiple rates, it will
work fine for ht mcs rates, as each supported mcs can be advertised
in ht_mcs index mask. But this will not work with vht rates because,
as per the vht mcs capability advertisement, there are only two bits
to indicate the supported mcs. E.g. only support 0-7, 0-8, 0-9.
So introduced new WMI command: WMI_PEER_PARAM_FIXED_RATE. After peer
assoc, the peer fixed rate cmd will work for that specific peer.
Remaining peers will use auto rate. If both vdev fixed rate and peer
fixed rates are given, peer fixed rate will take effect to peers for
which this cmd is given. Remaining peers in that vdev, will use vdev
fixed rate.
Tested HW: QCA9984
Tested FW: 10.4-3.9.0.2-00035
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The "WARNING" string confuses syzbot, which thinks it found
a crash [1].
Change the string to avoid such problem.
[1] https://lkml.org/lkml/2019/5/9/243
Reported-by: syzbot+c1b25598aa60dcd47e78@syzkaller.appspotmail.com
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In function ath10k_sdio_mbox_rx_alloc() [sdio.c],
ath10k_sdio_mbox_alloc_rx_pkt() is called without handling the error cases.
This will make the driver think the allocation for skb is successful and
try to access the skb. If we enable failslab, system will easily crash with
NULL pointer dereferencing.
Call trace of CONFIG_FAILSLAB:
ath10k_sdio_irq_handler+0x570/0xa88 [ath10k_sdio]
process_sdio_pending_irqs+0x4c/0x174
sdio_run_irqs+0x3c/0x64
sdio_irq_work+0x1c/0x28
Fixes: d96db25d20 ("ath10k: add initial SDIO support")
Signed-off-by: Claire Chang <tientzu@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For QCA988X target, pktlog gives details of the tx bitrate
which is used in the driver for station info.
Enabling pktlog by default will cause more interrupts
in target to host CE pipe, which can impact more CPU usage
for targets ex:WCN3990 and also not required for all other
platforms (eg: WCN3990), for getting tx bitrate.
Enable pktlog only for QCA988X based on hardware params.
Tested HW : WCN3990
Tested FW : WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: e8123bb74c ("ath10k: add per peer tx stats support for 10.2.4")
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Lockdep warns at lockdep_assert_held(&ar->data_lock) in
ath10k_htt_rx_pn_check_replay_hl(). Acquire ar->data_lock before calling
ath10k_htt_rx_pn_check_replay_hl() to fix it.
Call trace:
ath10k_htt_rx_pn_check_replay_hl+0x118/0x134 [ath10k_core]
ath10k_htt_rx_proc_rx_ind_hl+0xd8/0x250 [ath10k_core]
ath10k_htt_t2h_msg_handler+0x148/0xf30 [ath10k_core]
ath10k_htt_htc_t2h_msg_handler+0x24/0x40 [ath10k_core]
ath10k_sdio_irq_handler+0x374/0xaa4 [ath10k_sdio]
Fixes: 130c774957 ("ath10k: add PN replay protection for high latency devices")
Signed-off-by: Claire Chang <tientzu@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware name for UTF mode of SDIO has changed from utf-2.bin to
utf-sdio-2.bin, so it need to change in ath10k, otherwise it will
fail for UTF mode.
After change the name in ath10k, it will success for UTF mode of
SDIO/USB.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The command to simulate firmware crash:
echo soft > /sys/kernel/debug/ieee80211/phy0/ath10k/simulate_fw_crash
It will send WMI_FORCE_FW_HANG_ASSERT to firmware, then it will trigger
CPU interrupt status register for SDIO chip, ath10k driver need to
configure it while enable SDIO interrupt, otherwise ath10k driver will
not get the assert error info.
After this change, it will success for simulate firmware crash.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Tested-by: Claire Chang <tientzu@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k_dbg() is called in ath10k_process_rx() with huge set of arguments
which is causing CPU overhead even when debug_mask is not set.
Good improvement was observed in the receive side performance when call
to ath10k_dbg() is avoided in the RX path.
Since currently all debug messages are sent via tracing infrastructure,
we cannot entirely avoid calling ath10k_dbg. Therefore, call to
ath10k_dbg() is made conditional based on tracing config in the driver.
Trasmit performance remains unchanged with this patch; below are some
experimental results with this patch and tracing disabled.
mesh mode:
w/o this patch with this patch
Traffic TP CPU Usage TP CPU usage
TCP 840Mbps 76.53% 960Mbps 78.14%
UDP 1030Mbps 74.58% 1132Mbps 74.31%
Infra mode:
w/o this patch with this patch
Traffic TP CPU Usage TP CPU usage
TCP Rx 1241Mbps 80.89% 1270Mbps 73.50%
UDP Rx 1433Mbps 81.77% 1472Mbps 72.80%
Tested platform : IPQ8064
hardware used : QCA9984
firmware ver : ver 10.4-3.5.3-00057
Signed-off-by: Kan Yan <kyan@chromium.org>
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Without this op, it will not be possible to configure aggregation for
high latency devices.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is done in order to make the *htt_h2t_aggr_cfg_msg* op align better
with the rest of the htt ops (whom all have inline wrappers).
It also adds support for the case when the op is missing (function
pointer is NULL).
As a result of this, the name of the 32 bit implementation in htt_tx.c
was changed and the function was made static.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tx_stats will be freed and set to NULL before debugfs_sta node is
removed in station disconnetion process. So if read the debugfs_sta
node there may be NULL pointer error. Add check for tx_stats before
use it to resove this issue.
Signed-off-by: Yingying Tang <yintang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For some SDIO chip, the peer id is 65535 for MPDU with error status,
then test_bit will trigger buffer overflow for peer's memory, if kasan
enabled, it will report error.
Reason is when station is in disconnecting status, firmware do not delete
the peer info since it not disconnected completely, meanwhile some AP will
still send data packet to station, then hardware will receive the packet
and send to firmware, firmware's logic will report peer id of 65535 for
MPDU with error status.
Add check for overflow the size of peer's peer_ids will avoid the buffer
overflow access.
Call trace of kasan:
dump_backtrace+0x0/0x2ec
show_stack+0x20/0x2c
__dump_stack+0x20/0x28
dump_stack+0xc8/0xec
print_address_description+0x74/0x240
kasan_report+0x250/0x26c
__asan_report_load8_noabort+0x20/0x2c
ath10k_peer_find_by_id+0x180/0x1e4 [ath10k_core]
ath10k_htt_t2h_msg_handler+0x100c/0x2fd4 [ath10k_core]
ath10k_htt_htc_t2h_msg_handler+0x20/0x34 [ath10k_core]
ath10k_sdio_irq_handler+0xcc8/0x1678 [ath10k_sdio]
process_sdio_pending_irqs+0xec/0x370
sdio_run_irqs+0x68/0xe4
sdio_irq_work+0x1c/0x28
process_one_work+0x3d8/0x8b0
worker_thread+0x508/0x7cc
kthread+0x24c/0x264
ret_from_fork+0x10/0x18
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 firmware advertises the service WMI_TLV_SERVICE_MESH_11S
for mesh 11s. Map this wmi tlv service to enable mesh 11s
for WCN3990.
Tested HW: WCN3990
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently mac80211 do not support probe response template for
mesh point. When WMI_SERVICE_BEACON_OFFLOAD is enabled, host
driver tries to configure probe response template for mesh, but
it fails because the interface type is not NL80211_IFTYPE_AP but
NL80211_IFTYPE_MESH_POINT.
To avoid this failure, skip sending probe response template to
firmware for mesh point.
Tested HW: WCN3990/QCA6174/QCA9984
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a disparity in wmi and wmi tlv vdev subtype
enum for WMI_VDEV_SUBTYPE_MESH_11S.
Add different enum for wmi tlv vdev subtype to support
vdev of subtype mesh 11s for WCN3990.
Tested HW: WCN3990
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For SDIO chip, it does not have HTT connect step in boot phase of UTF
mode, so it does not need the swap configuration for UTF mode, otherwise
it will trigger UTF load fail. For normal mode, it is swap between HTT
and WMI, for UTF mode, it does not have HTT, so it can not swap between
HTT and WMI.
Disable swap mail box for UTF mode will let UTF mode load success.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The enum value for WMI_TLV_STAT_PDEV, WMI_TLV_STAT_VDEV
and WMI_TLV_STAT_PEER is wrong, due to which the vdev stats
are not received from firmware in wmi_update_stats event.
Fix the enum values for above stats to receive all stats
from firmware in WMI_TLV_UPDATE_STATS_EVENTID.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: f40a307eb9 ("ath10k: Fill rx duration for each peer in fw_stats for WCN3990)
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.
So, replace code of the following form:
sizeof(*ce_hdr) + CE_COUNT * sizeof(ce_hdr->entries[0])
with:
struct_size(ce_hdr, entries, CE_COUNT)
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.
So, change the following form:
sizeof(*rx) + (sizeof(struct htt_rx_indication_mpdu_range) * num_mpdu_ranges)
to :
struct_size(rx, mpdu_ranges, num_mpdu_ranges)
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently the protected management frames are
not appended with the MIC_LEN which results in
the protected management frames being encoded
incorrectly.
Add the extra space at the end of the protected
management frames to fix this encoding error for
the protected management frames.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: 1807da4973 ("ath10k: wmi: add management tx by reference support over wmi")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently instant rx_duration always fetching as zero
in fw_stats debugfs entry if extended peer stats event
supports.
This patch updates instant rx_duration in fw_stats entry
based on extended peer stats and maintaining backward
compatibility for 10.2/10.x.
Tested HW: QCA9984.
Tested FW: 10.4-3.6.0.1-00004.
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In tx_stats debugfs, txrate->flags may contain multiple bits. For
example, RATE_INFO_FLAGS_SHORT_GI could be set, and tx stats bytes
and packets will be not updated correctly.
Fix this issue by using bit operation to check txrate->flags.
Tested HW: QCA9984
Tested Firmware: 10.4-3.9.0.1-00007
Signed-off-by: Brandon Huang <yanghuan@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
CE4 is host to target HTT tx pipe, tx completion are not served
on time when CPU is loaded and this cause ce src ring full condition
due to less no of src buffer entries.
To mitigate the issue increase CE4 src buffer entries to 2048.
Testing:
Tested on QCS404 platform(WCN3990 HW)
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Board id and fw version is not printed by default in qmi
cap response message. Move board id and fw version logging
to info level for default logging.
[ 34.005399] ath10k_snoc a000000.wifi: qmi chip_id 0x30b chip_family 0x4001 board_id 0xff soc_id 0x40070000
[ 34.005432] ath10k_snoc a000000.wifi: qmi fw_version 0x3106836b fw_build_timestamp 2019-02-13 10:24 fw_build_id QC_IMAGE_VERSION_STRING=WLAN.HL.3.1-00875-QCAHLSWMTPL-1
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Reset HTT stats helps to get the aggregated HTT stats via
tracing and also we can clear the accumulated HTT stats with
this debugfs file.
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Extended the bit mask value of the HTT stats to get the Mu-MIMO
related stats via tracing.
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Invalid rate code is sent to firmware when multicast rate value of 0 is
sent to driver indicating disabled case, causing broken mesh path.
so fix that.
Tested on QCA9984 with firmware 10.4-3.6.1-00827
Sven tested on IPQ4019 with 10.4-3.5.3-00057 and QCA9888 with 10.4-3.5.3-00053
(ath10k-firmware) and 10.4-3.6-00140 (linux-firmware 2018-12-16-211de167).
Fixes: cd93b83ad9 ("ath10k: support for multicast rate control")
Co-developed-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Tested-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After implementing PN replay check we can enable SDIO support on QCA6174.
Tested with client mode on all security modes, and fragmentation as well. AP
mode does not work yet.
Also tone down the warning about SDIO being not ready yet.
Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1. AP mode
is not working yet.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On high latency devices (SDIO, USB) ath10k did not handle fragmented frames and
all fragmented frames on receive path were lost in ath10k. Even a simple ping
test failed with fragmentation.
The fragmented packets are decapsulated based on the security mode, then the PN
is checked and the fragmented frame is passed to mac80211. mac80211 in
ieee80211_rx_h_defragment() will then combine the fragment frames and forward
to upper layers.
Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On high latency devices (SDIO, USB) ath10k did not do PN replay check, a data
frame with an invalid PN number was not discard as it should have been. So this
patch implements PN replay in ath10k. PN replay check for fragmented frames is
implemented in followup patch.
With low latency devices (PCI, AHB) hardware can store the data
frames's content to host memory directly and the firmware can fully reorder
data frames, and do PN replay check at the same time. But for high latency
devices all data frames will be received and stored in firmware's memory and it
is hard to do full reorder because of the memory size limitations in the
firmware. This is why the PN replay protections needs to be implemented in host
driver.
Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add the handler for HTT_T2H_MSG_TYPE_SEC_IND event from firmware, which stores
PN for replay check implemented in the following patch.
Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
