When the PF receives a mailbox message from the VF, it grabs the mailbox
lock, reads the VF message from the mailbox, ACKs the message and drops
the lock.
While the PF is performing the action for the VF message, nothing
prevents another VF message from being posted to the mailbox. The
current code handles this condition by just dropping any new VF messages
without processing them. This results in a mailbox timeout in the VM
for posted messages waiting for an ACK, and the VF is reset by the
igbvf_watchdog_task in the VM.
Given the right sequence of VF messages and mailbox timeouts, this
condition can go on ad infinitum.
Modify the PF mailbox read method to take an 'unlock' argument that
optionally leaves the mailbox locked by the PF after reading the VF
message. This ensures another VF message is not posted to the mailbox
until after the PF has completed processing the VF message and written
its reply.
Signed-off-by: Greg Edwards <gedwards@ddn.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a mailbox unlock method to e1000_mbx_operations, which will be used
to unlock the PF/VF mailbox by the PF.
Signed-off-by: Greg Edwards <gedwards@ddn.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
TSAUXC.DisableSystime is never set, so SYSTIM runs into a SYS WRAP
every 1100 secs on 80580/i350/i354 (40 bit SYSTIM) and every 35000
secs on 80576 (45 bit SYSTIM).
This wrap event sets the TSICR.SysWrap bit unconditionally.
However, checking TSIM at interrupt time shows that this event does not
actually cause the interrupt. Rather, it's just bycatch while the
actual interrupt is caused by, for instance, TSICR.TXTS.
The conclusion is that the SYS WRAP is actually expected, so the
"unexpected SYS WRAP" message is entirely bogus and just helps to
confuse users. Drop it.
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
HW timestamping can only be requested for a packet if the NIC is first
setup via ioctl(SIOCSHWTSTAMP). If this step was skipped, then the igb
driver still allowed TX packets to request HW timestamping. In this
situation, the _IGB_PTP_TX_IN_PROGRESS flag was set and would never
clear. This prevented any future HW timestamping requests to succeed.
Fix this by checking that the NIC is configured for HW TX timestamping
before accepting a HW TX timestamping request.
Signed-off-by: Cliff Spradlin <cspradlin@google.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
After add an ethertype filter, if user change the adapter speed several
times, the error "ethtool -N: etype filters are all used" is reported by
igb driver.
In older patch, function igb_nfc_filter_exit() and igb_nfc_filter_restore()
is not paried. igb_nfc_filter_restore() exist in igb_up(), but function
igb_nfc_filter_exit() is exist in __igb_close(). In the process of speed
changing, only igb_nfc_filter_restore() is called, it will take a position
of ethertype bitmap.
Reproduce steps:
Step 1: Add a etype filter by ethtool
$ethtool -N eth0 flow-type ether proto 0x88F8 action 1
Step 2: Change the adapter speed to 100M/full duplex
$ethtool -s eth0 speed 100 duplex full
Step 3: Change the adapter speed to 1000M/full duplex
ethtool -s eth0 speed 1000 duplex full
Repeat step2 and step3, then dmesg the system log, you can find the error
message, add new ethtype filter is also failed.
This fixing is move igb_nfc_filter_exit() from __igb_close() to igb_down()
to make igb_nfc_filter_restore()/igb_nfc_filter_exit() is paired.
Signed-off-by: Gangfeng Huang <gangfeng.huang@ni.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clean up a few sparse warnings, these following
functions can be made static:
drivers/net/ethernet/intel/igb/igb_main.c: warning: symbol
'igb_add_mac_filter' was not declared. Should it be static?
drivers/net/ethernet/intel/igb/igb_main.c: warning: symbol
'igb_del_mac_filter' was not declared. Should it be static?
drivers/net/ethernet/intel/igb/igb_main.c: warning: symbol
'igb_set_vf_mac_filter' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Given that all callers of igb_update_stats() pass the same two arguments:
(adapter, &adapter->stats64), the second argument can be removed.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The igb driver has logic to handle only one Tx timestamp at a time,
using a state bit lock to avoid multiple requests at once.
It may be possible, if incredibly unlikely, that a Tx timestamp event is
requested but never completes. Since we use an interrupt scheme to
determine when the Tx timestamp occurred we would never clear the state
bit in this case.
Add an igb_ptp_tx_hang() function similar to the already existing
igb_ptp_rx_hang() function. This function runs in the watchdog routine
and makes sure we eventually recover from this case instead of
permanently disabling Tx timestamps.
Note: there is no currently known way to cause this without hacking the
driver code to force it.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The igb driver can only handle one Tx timestamp request at a time.
This means it is possible for an application timestamp request to be
ignored.
There is no easy way for an administrator to determine if this occurred.
Add a new statistic which tracks this, tx_hwtstamp_skipped.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The igb driver uses a state bit lock to avoid handling more than one Tx
timestamp request at once. This is required because hardware is limited
to a single set of registers for Tx timestamps.
The state bit lock is not properly cleaned up during
igb_xmit_frame_ring() if the transmit fails such as due to DMA or TSO
failure. In some hardware this results in blocking timestamps until the
service task times out. In other hardware this results in a permanent
lock of the timestamp bit because we never receive an interrupt
indicating the timestamp occurred, since indeed the packet was never
transmitted.
Fix this by checking for DMA and TSO errors in igb_xmit_frame_ring() and
properly cleaning up after ourselves when these occur.
Reported-by: Reported-by: David Mirabito <davidm@metamako.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Hardware related to the igb driver has a limitation of only handling one
Tx timestamp at a time. Thus, the driver uses a state bit lock to
enforce that only one timestamp request is honored at a time.
Unfortunately this suffers from a simple race condition. The bit lock is
not cleared until after skb_tstamp_tx() is called notifying the stack of
a new Tx timestamp. Even a well behaved application which sends only one
timestamp request at once and waits for a response might wake up and
send a new packet before the bit lock is cleared. This results in
needlessly dropping some Tx timestamp requests.
We can fix this by unlocking the state bit as soon as we read the
Timestamp register, as this is the first point at which it is safe to
unlock.
To avoid issues with the skb pointer, we'll use a copy of the pointer
and set the global variable in the driver structure to NULL first. This
ensures that the next timestamp request does not modify our local copy
of the skb pointer.
This ensures that well behaved applications do not accidentally race
with the unlock bit. Obviously an application which sends multiple Tx
timestamp requests at once will still only timestamp one packet at
a time. Unfortunately there is nothing we can do about this.
Reported-by: David Mirabito <davidm@metamako.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The new wake function is only used by the suspend/resume handlers that
are defined in inside of an #ifdef, which can cause this harmless
warning:
drivers/net/ethernet/intel/igb/igb_main.c:7988:13: warning: 'igb_deliver_wake_packet' defined but not used [-Wunused-function]
Removing the #ifdef, instead using a __maybe_unused annotation
simplifies the code and avoids the warning.
Fixes: b90fa87635 ("igb: Enable reading of wake up packet")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The functions igb_read_phy_reg_gs40g/igb_write_phy_reg_gs40g (which were
removed in 2a3cdea) explicitly selected the required page at every phy_reg
access. Currently, igb_get_phy_id_82575 relays on the fact that page 0 is
already selected. The assumption is not fulfilled for my Lex 3I380CW
motherboard with integrated dual i211 based gigabit ethernet. This leads to igb
initialization failure and network interfaces are not working:
igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k
igb: Copyright (c) 2007-2014 Intel Corporation.
igb: probe of 0000:01:00.0 failed with error -2
igb: probe of 0000:02:00.0 failed with error -2
In order to fix it, we explicitly select page 0 before first access to phy
registers.
See also: https://bugzilla.suse.com/show_bug.cgi?id=1009911
See also: http://www.lex.com.tw/products/pdf/3I380A&3I380CW.pdf
Fixes: 2a3cdea ("igb: Remove GS40G specific defines/functions")
Cc: <stable@vger.kernel.org> # 4.5+
Signed-off-by: Matwey V Kornilov <matwey@sai.msu.ru>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Include HWTSTAMP_FILTER_NTP_ALL in net_hwtstamp_validate() as a valid
filter and update drivers which can timestamp all packets, or which
explicitly list unsupported filters instead of using a default case, to
handle the filter.
CC: Richard Cochran <richardcochran@gmail.com>
CC: Willem de Bruijn <willemb@google.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This typo is quite common. Fix it and add it to the spelling file so
that checkpatch catches it earlier.
Link: http://lkml.kernel.org/r/20170317011131.6881-2-sboyd@codeaurora.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, in igb_resume(), igb driver ignores the Wake Up Status (WUS)
and Wake Up Packet Memory (WUPM) registers. This patch enables the igb
driver to read the WUPM if the controller was woken by a wake up packet
that is not more than 128 bytes long (maximum WUPM size), then pass it
up the kernel network stack.
Signed-off-by: Kim Tatt Chuah <kim.tatt.chuah@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add functionality for the VF to request up to 3 additional MAC filters.
This is done using existing E1000_VF_SET_MAC_ADDR message, but with
additional message info - E1000_VF_MAC_FILTER_CLR to clear all unicast
MAC filters previously set for this VF and E1000_VF_MAC_FILTER_ADD to
add MAC filter.
Additional filters can be added only in case if administrator did not
set VF MAC explicitly and allowed to change default MAC to the VF.
Due to the limited number of RAR entries reserve at least 3 MAC filters
for the PF.
If SRIOV is supported by the NIC after this change RAR entries starting
from 1 to (RAR MAX ENTRIES - NUM SRIOV VFS) will be used for PF and VF
MAC filters.
Signed-off-by: Yury Kylulin <yury.kylulin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Using the work which was done for ixgbe driver by Jacob Keller
commit 5d7daa35b9 ("ixgbe: improve mac filter handling") and Alexander
Duyck commit 0f079d2283 ("ixgbe: Use __dev_uc_sync and __dev_uc_unsync
for unicast addresses") and out-of-tree igb driver add functionality to
manage (add and delete) MAC filters.
Signed-off-by: Yury Kylulin <yury.kylulin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ethtool API {get|set}_settings is deprecated.
We move this driver to new API {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There was a typo that I had left in the code comments for the igb and ixgbe
functions that enabled build_skb support.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This reverts commit f9d40f6a99 ("igb: Revert support for build_skb in
igb") and adds a few changes to update it to work with the latest version
of igb. We are now able to revert the removal of this due to the fact
that with the recent changes to the page count and the use of
DMA_ATTR_SKIP_CPU_SYNC we can make the pages writable so we should not be
invalidating the additional data added when we call build_skb.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
At this point we have 2 to 3 paths that can be taken depending on what Rx
modes are enabled. In order to better support that and improve the
maintainability I am breaking out the common bits from those paths and
making them into their own functions.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With the size of the frame limited we can now write to an offset within the
buffer instead of having to write at the very start of the buffer. The
advantage to this is that it allows us to leave padding room for things
like supporting XDP in the future.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for using 3K buffers in order 1 pages the same way
we were using 2K buffers in 4K pages. We are reserving 1K of room for now
to have space available for future headroom and tailroom when we enable
build_skb support.
One side effect of this patch is that we can end up using a larger buffer
if jumbo frames is enabled. The impact shouldn't be too great, but it
could hurt small packet performance for UDP workloads if jumbo frames is
enabled as the truesize of frames will be larger.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since there are potential drawbacks to the new Rx allocation approach I
thought it best to add a "chicken bit" so that we can turn the feature off
if in the event that a problem is found.
It also provides a means of validating the legacy Rx path in the event that
we are forced to fall back. At some point in the future when we are
convinced we don't need it anymore we might be able to drop the legacy-rx
flag.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update the handling of page addresses so that we always refer to them using
a void pointer, and try to use the consistent name of va indicating we are
working with a virtual address.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We only need to sync the size of the frame that is read to test. We don't
need to sync the entire Rx buffer. This way the testing is more consistent
with how we handle things in the receive path.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In order to support the use of build_skb going forward it will be necessary
to place a maximum limit on the amount of data we can receive when jumbo
frames is not enabled. In order to do this I am adding a new upper limit
for receive based on the size of a 2K buffer minus padding.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the case of the Tx rings we need to only clear the Tx buffer_info when
we are resetting the rings. Ideally we do this when we configure the ring
to bring it back up instead of when we are taking it down in order to avoid
dirtying pages we don't need to.
In addition we don't need to clear the Tx descriptor ring since we will
fully repopulate it when we begin transmitting frames and next_to_watch can
be cleared to prevent the ring from being cleaned beyond that point instead
of needing to touch anything in the Tx descriptor ring.
Finally with these changes we can avoid having to reset the skb member of
the Tx buffer_info structure in the cleanup path since the skb will always
be associated with the first buffer which has next_to_watch set.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that instead of going through the entire ring on Rx
cleanup we only go through the region that was designated to be cleaned up
and stop when we reach the region where new allocations should start.
In addition we can avoid having to perform a memset on the Rx buffer_info
structures until we are about to start using the ring again. By deferring
this we can avoid dirtying the cache any more than we have to which can
help to improve the time needed to bring the interface down and then back
up again in a reset or suspend/resume cycle.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we use the length of the packet instead of the
DD status bit to determine if a new descriptor is ready to be processed.
The obvious advantage is that it cuts down on reads as we don't really even
need the DD bit if going from a 0 to a non-zero value on size is enough to
inform us that the packet has been completed.
In addition I have updated the code so that we only reset the Rx descriptor
length for descriptor zero when resetting a ring instead of having to do a
memset with 0 over the entire ring. By doing this we can save some time on
initialization.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since we are already using DMA attributes in igb for Rx there is no reason
why we can't also apply DMA_ATTR_WEAK_ORDERING which is needed on some
platforms to improve performance.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix typos and add the following to the scripts/spelling.txt:
overwritting||overwriting
Link: http://lkml.kernel.org/r/1481573103-11329-29-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The network stack no longer uses the last_rx member of struct net_device
since the bonding driver switched to use its own private last_rx in
commit 9f24273837 ("bonding: use last_arp_rx in slave_last_rx()").
However, some drivers still (ab)use the field for their own purposes and
some driver just update it without actually using it.
Previously, there was an accompanying comment for the last_rx member
added in commit 4dc89133f4 ("net: add a comment on netdev->last_rx")
which asked drivers not to update is, unless really needed. However,
this commend was removed in commit f8ff080dac ("bonding: remove
useless updating of slave->dev->last_rx"), so some drivers added later
on still did update last_rx.
Remove all usage of last_rx and switch three drivers (sky2, atp and
smc91c92_cs) which actually read and write it to use their own private
copy in netdev_priv.
Compile-tested with allyesconfig and allmodconfig on x86 and arm.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Mirko Lindner <mlindner@marvell.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does two things.
First it goes through and renames the __page_frag prefixed functions to
__page_frag_cache so that we can be clear that we are draining or
refilling the cache, not the frags themselves.
Second we drop the order parameter from __page_frag_cache_drain since we
don't actually need to pass it since all fragments are either order 0 or
must be a compound page.
Link: http://lkml.kernel.org/r/20170104023954.13451.5678.stgit@localhost.localdomain
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.
Fix all drivers with ndo_get_stats64 to have a void function.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix an if statement with hw_dbg lines where the logic was inverted with
regards to the corresponding return value used in the if statement.
Signed-off-by: Hannu Lounento <hannu.lounento@ge.com>
Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i210 and i211 share the same PHY but have different PCI IDs. Don't
forget i211 for any i210 workarounds.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Similar to ixgbe, when an interface is part of a namespace it is
possible that igb_close() may be called while __igb_shutdown() is
running which ends up in a double free WARN and/or a BUG in
free_msi_irqs().
Extend the rtnl_lock() to protect the call to netif_device_detach() and
igb_clear_interrupt_scheme() in __igb_shutdown() and check for
netif_device_present() to avoid calling igb_clear_interrupt_scheme() a
second time in igb_close().
Also extend the rtnl lock in igb_resume() to netif_device_attach().
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Whenever the igb driver detects the result of a read operation returns
a value composed only by F's (like 0xFFFFFFFF), it will detach the
net_device, clear the hw_addr pointer and warn to the user that adapter's
link is lost - those steps happen on igb_rd32().
In case a PCI error happens on Power architecture, there's a recovery
mechanism called EEH, that will reset the PCI slot and call driver's
handlers to reset the adapter and network functionality as well.
We observed that once hw_addr is NULL after the error is detected on
igb_rd32(), it's never assigned back, so in the process of resetting
the network functionality we got a NULL pointer dereference in both
igb_configure_tx_ring() and igb_configure_rx_ring(). In order to avoid
such bug, this patch re-assigns the hw_addr value in the slot_reset
handler.
Reported-by: Anthony H Thai <ahthai@us.ibm.com>
Reported-by: Harsha Thyagaraja <hathyaga@in.ibm.com>
Signed-off-by: Guilherme G Piccoli <gpiccoli@linux.vnet.ibm.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Several people have reported firmware leaving the I210/I211 PHY's page
select register set to something other than the default of zero. This
causes the first accesses, PHY_IDx register reads, to access something
else, resulting in device probe failure:
igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k
igb: Copyright (c) 2007-2014 Intel Corporation.
igb: probe of 0000:01:00.0 failed with error -2
This problem began for them after a previous patch I submitted was
applied:
commit 2a3cdead8b
Author: Aaron Sierra <asierra@xes-inc.com>
Date: Tue Nov 3 12:37:09 2015 -0600
igb: Remove GS40G specific defines/functions
I personally experienced this problem after attempting to PXE boot from
I210 devices using this firmware:
Intel(R) Boot Agent GE v1.5.78
Copyright (C) 1997-2014, Intel Corporation
Resetting the PHY before reading from it, ensures the page select
register is in its default state and doesn't make assumptions about
the PHY's register set before the PHY has been probed.
Cc: Matwey V. Kornilov <matwey@sai.msu.ru>
Cc: Chris Arges <carges@vectranetworks.com>
Cc: Jochen Henneberg <jh@henneberg-systemdesign.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Tested-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Tested-by: Chris J Arges <christopherarges@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When running as guest, under certain condition, it will oops as following.
writel() in igb_configure_tx_ring() results in oops, because hw->hw_addr
is NULL. While other register access won't oops kernel because they use
wr32/rd32 which have a defense against NULL pointer.
[ 141.225449] pcieport 0000:00:1c.0: AER: Multiple Uncorrected (Fatal)
error received: id=0101
[ 141.225523] igb 0000:01:00.1: PCIe Bus Error:
severity=Uncorrected (Fatal), type=Unaccessible,
id=0101(Unregistered Agent ID)
[ 141.299442] igb 0000:01:00.1: broadcast error_detected message
[ 141.300539] igb 0000:01:00.0 enp1s0f0: PCIe link lost, device now
detached
[ 141.351019] igb 0000:01:00.1 enp1s0f1: PCIe link lost, device now
detached
[ 143.465904] pcieport 0000:00:1c.0: Root Port link has been reset
[ 143.465994] igb 0000:01:00.1: broadcast slot_reset message
[ 143.466039] igb 0000:01:00.0: enabling device (0000 -> 0002)
[ 144.389078] igb 0000:01:00.1: enabling device (0000 -> 0002)
[ 145.312078] igb 0000:01:00.1: broadcast resume message
[ 145.322211] BUG: unable to handle kernel paging request at
0000000000003818
[ 145.361275] IP: [<ffffffffa02fd38d>]
igb_configure_tx_ring+0x14d/0x280 [igb]
[ 145.400048] PGD 0
[ 145.438007] Oops: 0002 [#1] SMP
A similar issue & solution could be found at:
http://patchwork.ozlabs.org/patch/689592/
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sometimes firmware may not properly initialize I347AT4_PAGE_SELECT causing
the probe of an igb i210 NIC to fail. This patch adds an addition zeroing
of this register during igb_get_phy_id to workaround this issue.
Thanks for Jochen Henneberg for the idea and original patch.
Signed-off-by: Chris J Arges <christopherarges@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Statements should start on tabstops.
Use a single statement and test instead of multiple tests.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is no point in having an extra type for extra confusion. u64 is
unambiguous.
Conversion was done with the following coccinelle script:
@rem@
@@
-typedef u64 cycle_t;
@fix@
typedef cycle_t;
@@
-cycle_t
+u64
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
Update the driver code so that we do bulk updates of the page reference
count instead of just incrementing it by one reference at a time. The
advantage to doing this is that we cut down on atomic operations and
this in turn should give us a slight improvement in cycles per packet.
In addition if we eventually move this over to using build_skb the gains
will be more noticeable.
Link: http://lkml.kernel.org/r/20161110113616.76501.17072.stgit@ahduyck-blue-test.jf.intel.com
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Cc: Helge Deller <deller@gmx.de>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Keguang Zhang <keguang.zhang@gmail.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ARM architecture provides a mechanism for deferring cache line
invalidation in the case of map/unmap. This patch makes use of this
mechanism to avoid unnecessary synchronization.
A secondary effect of this change is that the portion of the page that
has been synchronized for use by the CPU should be writable and could be
passed up the stack (at least on ARM).
The last bit that occurred to me is that on architectures where the
sync_for_cpu call invalidates cache lines we were prefetching and then
invalidating the first 128 bytes of the packet. To avoid that I have
moved the sync up to before we perform the prefetch and allocate the
skbuff so that we can actually make use of it.
Link: http://lkml.kernel.org/r/20161110113611.76501.98897.stgit@ahduyck-blue-test.jf.intel.com
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Cc: Helge Deller <deller@gmx.de>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Keguang Zhang <keguang.zhang@gmail.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Couple conflicts resolved here:
1) In the MACB driver, a bug fix to properly initialize the
RX tail pointer properly overlapped with some changes
to support variable sized rings.
2) In XGBE we had a "CONFIG_PM" --> "CONFIG_PM_SLEEP" fix
overlapping with a reorganization of the driver to support
ACPI, OF, as well as PCI variants of the chip.
3) In 'net' we had several probe error path bug fixes to the
stmmac driver, meanwhile a lot of this code was cleaned up
and reorganized in 'net-next'.
4) The cls_flower classifier obtained a helper function in
'net-next' called __fl_delete() and this overlapped with
Daniel Borkamann's bug fix to use RCU for object destruction
in 'net'. It also overlapped with Jiri's change to guard
the rhashtable_remove_fast() call with a check against
tc_skip_sw().
5) In mlx4, a revert bug fix in 'net' overlapped with some
unrelated changes in 'net-next'.
6) In geneve, a stale header pointer after pskb_expand_head()
bug fix in 'net' overlapped with a large reorganization of
the same code in 'net-next'. Since the 'net-next' code no
longer had the bug in question, there was nothing to do
other than to simply take the 'net-next' hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case of IPIP and SIT tunnel frames the outer transport header
offset is actually set to the same offset as the inner transport header.
This results in the lco_csum call not doing any checksum computation over
the inner IPv4/v6 header data.
In order to account for that I am updating the code so that we determine
the location to start the checksum ourselves based on the location of the
IPv4 header and the length.
Fixes: e10715d3e9 ("igb/igbvf: Add support for GSO partial")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 82580 and related devices offer a frequency resolution of about
0.029 ppb. This patch lets users of the device benefit from the
increased frequency resolution when tuning the clock.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e100: min_mtu 68, max_mtu 1500
- remove e100_change_mtu entirely, is identical to old eth_change_mtu,
and no longer serves a purpose. No need to set min_mtu or max_mtu
explicitly, as ether_setup() will already set them to 68 and 1500.
e1000: min_mtu 46, max_mtu 16110
e1000e: min_mtu 68, max_mtu varies based on adapter
fm10k: min_mtu 68, max_mtu 15342
- remove fm10k_change_mtu entirely, does nothing now
i40e: min_mtu 68, max_mtu 9706
i40evf: min_mtu 68, max_mtu 9706
igb: min_mtu 68, max_mtu 9216
- There are two different "max" frame sizes claimed and both checked in
the driver, the larger value wasn't relevant though, so I've set max_mtu
to the smaller of the two values here to retain identical behavior.
igbvf: min_mtu 68, max_mtu 9216
- Same issue as igb duplicated
ixgb: min_mtu 68, max_mtu 16114
- Also remove pointless old == new check, as that's done in dev_set_mtu
ixgbe: min_mtu 68, max_mtu 9710
ixgbevf: min_mtu 68, max_mtu dependent on hardware/firmware
- Some hw can only handle up to max_mtu 1504 on a vf, others 9710
CC: netdev@vger.kernel.org
CC: intel-wired-lan@lists.osuosl.org
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a reset occurs, the PPS SYS_WRAP interrupt was not re-enabled which
resulted in disabling of the PPS signaling. Fix this by recording when
the interrupt is on and ensuring that we re-enable it every time we
reset.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump igb version to match other igb drivers.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixes the following sparse warning:
drivers/net/ethernet/intel/igb/igb_ethtool.c:2707:5: warning:
symbol 'igb_rxnfc_write_vlan_prio_filter' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Introduce new rtnl UAPI that exposes a list of vlans per VF, giving
the ability for user-space application to specify it for the VF, as an
option to support 802.1ad.
We adjusted IP Link tool to support this option.
For future use cases, the new UAPI supports multiple vlans. For now we
limit the list size to a single vlan in kernel.
Add IFLA_VF_VLAN_LIST in addition to IFLA_VF_VLAN to keep backward
compatibility with older versions of IP Link tool.
Add a vlan protocol parameter to the ndo_set_vf_vlan callback.
We kept 802.1Q as the drivers' default vlan protocol.
Suitable ip link tool command examples:
Set vf vlan protocol 802.1ad:
ip link set eth0 vf 1 vlan 100 proto 802.1ad
Set vf to VST (802.1Q) mode:
ip link set eth0 vf 1 vlan 100 proto 802.1Q
Or by omitting the new parameter
ip link set eth0 vf 1 vlan 100
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers must be ready to accept NULL from ptp_clock_register() if the
PTP clock subsystem is configured out.
This patch documents that and ensures that all drivers cope well
with a NULL return.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Eugenia Emantayev <eugenia@mellanox.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use error "rmgr: Cannot insert RX class rule: Operation not supported" is
more meaningful than "rmgr: Cannot insert RX class rule: Unknown error 524"
Signed-off-by: Gangfeng Huang <gangfeng.huang@ni.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to allow for RX network flow classification to insert
and remove ethertype filter by ethtool
Example:
Add an ethertype filter:
$ ethtool -N eth0 flow-type ether proto 0x88F8 action 2
Show all filters:
$ ethtool -n eth0
4 RX rings available
Total 1 rules
Filter: 15
Flow Type: Raw Ethernet
Src MAC addr: 00:00:00:00:00:00 mask: FF:FF:FF:FF:FF:FF
Dest MAC addr: 00:00:00:00:00:00 mask: FF:FF:FF:FF:FF:FF
Ethertype: 0x88F8 mask: 0x0
Action: Direct to queue 2
Delete the filter by location:
$ ethtool -N delete 15
Signed-off-by: Ruhao Gao <ruhao.gao@ni.com>
Signed-off-by: Gangfeng Huang <gangfeng.huang@ni.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to allow for RX network flow classification to insert
and remove Rx filter by ethtool. Ethtool interface has it's own rules
manager
Show all filters:
$ ethtool -n eth0
4 RX rings available
Total 2 rules
Signed-off-by: Ruhao Gao <ruhao.gao@ni.com>
Signed-off-by: Gangfeng Huang <gangfeng.huang@ni.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix PHY delay compensation math in igb_ptp_tx_hwtstamp() and
igb_ptp_rx_rgtstamp. Add PHY delay compensation in
igb_ptp_rx_pktstamp().
In the IGB driver, there are two functions that retrieve timestamps
received by the PHY - igb_ptp_rx_rgtstamp() and igb_ptp_rx_pktstamp().
The previous commit only changed igb_ptp_rx_rgtstamp(), and the change
was incorrect.
There are two instances in which PHY delay compensations should be
made:
- Before the packet transmission over the PHY, the latency between
when the packet is timestamped and transmission of the packets,
should be an add operation, but it is currently a subtract.
- After the packets are received from the PHY, the latency between
the receiving and timestamping of the packets should be a subtract
operation, but it is currently an add.
Signed-off-by: Kshitiz Gupta <kshitiz.gupta@ni.com>
Fixes: 3f544d2 (igb: adjust ptp timestamps for tx/rx latency)
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On some platforms, syncing a buffer for DMA is expensive. Rather than
sync the whole 2K receive buffer, only synchronise the length of the
frame, which will typically be the MTU, or a much smaller TCP ACK.
For an IMX6Q, this gives around 6% increased TCP receive performance,
which is cache operations bound and reduces CPU load for TCP transmit.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Properly stop the extra workqueue items and ensure that we resume
cleanly. This is better than using igb_ptp_init and igb_ptp_stop since
these functions destroy the PHC device, which will cause other problems
if we do so. Since igb_ptp_reset now re-schedules the work-queue item we
don't need an equivalent igb_ptp_resume in the resume workflow.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make igb_ptp_stop take advantage of this new function to reduce code
duplication.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Modify igb_ptp_init to take advantage of igb_ptp_reset, and remove
duplicated work that was occurring in both igb_ptp_reset and
igb_ptp_init.
In total, resetting the TSAUXC register, and resetting the system time
both happen in igb_ptp_reset already. igb_ptp_reset now also takes care
of starting the delayed work item for overflow checks, as well.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't continue to use complex MAC type checks for handling various cases
where we have overflow check code. Make this code more obvious by
introducing a flag which is enabled for hardware that needs these
checks.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Upcoming patches will introduce new PTP specific flags. To avoid
cluttering the normal flags variable, introduce PTP specific "ptp_flags"
variable for this purpose, and move IGB_FLAG_PTP to become
IGB_PTP_ENABLED.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that we do have pci_request_mem_regions() and pci_release_mem_regions()
at hand, use it in the Intel ethernet drivers.
Suggested-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: David S. Miller <davem@davemloft.net>
This patch adds support for offloading IPXIP6 type packets that represent
either IPv4 or IPv6 encapsulated inside of an IPv6 outer IP header. In
addition with this change we should also be able to support FOU
encapsulated traffic with outer IPv6 headers.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch defines two new GSO definitions SKB_GSO_IPXIP4 and
SKB_GSO_IPXIP6 along with corresponding NETIF_F_GSO_IPXIP4 and
NETIF_F_GSO_IPXIP6. These are used to described IP in IP
tunnel and what the outer protocol is. The inner protocol
can be deduced from other GSO types (e.g. SKB_GSO_TCPV4 and
SKB_GSO_TCPV6). The GSO types of SKB_GSO_IPIP and SKB_GSO_SIT
are removed (these are both instances of SKB_GSO_IPXIP4).
SKB_GSO_IPXIP6 will be used when support for GSO with IP
encapsulation over IPv6 is added.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for partial GSO segmentation in the case of
tunnels. Specifically with this change the driver an perform segmentation
as long as the frame either has IPv6 inner headers, or we are allowed to
mangle the IP IDs on the inner header. This is needed because we will not
be modifying any fields from the start of the start of the outer transport
header to the start of the inner transport header as we are treating them
like they are just a block of IP options.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Table 7-62 on page 338 of the i210 datasheet lists TX and RX latencies
for the various speeds the chip supports. To give better PTP timestamp
accuracy, adjust the timestamps by the amounts Intel gives based on
current link speed.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For bitshifts, we should make use of the BIT macro when possible, and
ensure that other bitshifts are marked as unsigned. This helps prevent
signed bitshift errors, and ensures similar style.
Make use of GENMASK and the unsigned postfix where BIT() isn't
appropriate.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
a trans_start struct member exists twice:
- in struct net_device (legacy)
- in struct netdev_queue
Instead of open-coding dev->trans_start usage to obtain the current
trans_start value, use dev_trans_start() instead.
This is not exactly the same, as dev_trans_start also considers
the trans_start values of the netdev queues owned by the device
and provides the most recent one.
For legacy devices this doesn't matter as dev_trans_start can cope
with netdev trans_start values of 0 (they are ignored).
This is a prerequisite to eventual removal of dev->trans_start.
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 3eb14ea8d9 ("igb: Fix a deadlock in
igb_sriov_reinit")
It is the same as commit f468adc944 ("igb: missing rtnl_unlock in
igb_sriov_reinit()")
There is no rtnl_lock() in igb_resume before, rtnl_unlock will cause a
deadlock.
Signed-off-by: Arika Chen <arika.chen@huawei.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Garbled output for "ethtool -m ethX", in igb-driven NICs with module /
plugin EEPROM (i.e. SFP information). Each output data byte appears
duplicated.
In igb_ethtool.c, igb_get_module_eeprom() is reading the EEPROM via i2c;
the eeprom offset for each word that's read via igb_read_phy_reg_i2c()
was passed in #words, whereas it needs to be a byte offset.
This patches fixes the bug.
Signed-off-by: Doron Shikmoni <doron.shikmoni@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The Intel i211 LOM PCIe Ethernet controllers' iNVM operates as an OTP
and has no external EEPROM interface [1]. The following allows the
driver to pickup the MAC address from a device tree blob when CONFIG_OF
has been enabled.
[1]
http://www.intel.com/content/www/us/en/embedded/products/networking/i211-ethernet-controller-datasheet.html
Signed-off-by: John Holland <jotihojr@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables bulk free in Tx cleanup for igb and cleans up the
boolean logic in the polling routines for igb in the hopes of avoiding
any mix-ups similar to what occurred with i40e and i40evf.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were casting the addr as __beXX and then passing it into le32_to_cpu
because the device expects the MAC address to be in network order even
though the register set is little endian. Instead of casting it as __beXX
we can just cast it as __leXX in order to maintain consistency since the
region of memory is already in little endian order as far as we are
concerned.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull networking updates from David Miller:
"Highlights:
1) Support more Realtek wireless chips, from Jes Sorenson.
2) New BPF types for per-cpu hash and arrap maps, from Alexei
Starovoitov.
3) Make several TCP sysctls per-namespace, from Nikolay Borisov.
4) Allow the use of SO_REUSEPORT in order to do per-thread processing
of incoming TCP/UDP connections. The muxing can be done using a
BPF program which hashes the incoming packet. From Craig Gallek.
5) Add a multiplexer for TCP streams, to provide a messaged based
interface. BPF programs can be used to determine the message
boundaries. From Tom Herbert.
6) Add 802.1AE MACSEC support, from Sabrina Dubroca.
7) Avoid factorial complexity when taking down an inetdev interface
with lots of configured addresses. We were doing things like
traversing the entire address less for each address removed, and
flushing the entire netfilter conntrack table for every address as
well.
8) Add and use SKB bulk free infrastructure, from Jesper Brouer.
9) Allow offloading u32 classifiers to hardware, and implement for
ixgbe, from John Fastabend.
10) Allow configuring IRQ coalescing parameters on a per-queue basis,
from Kan Liang.
11) Extend ethtool so that larger link mode masks can be supported.
From David Decotigny.
12) Introduce devlink, which can be used to configure port link types
(ethernet vs Infiniband, etc.), port splitting, and switch device
level attributes as a whole. From Jiri Pirko.
13) Hardware offload support for flower classifiers, from Amir Vadai.
14) Add "Local Checksum Offload". Basically, for a tunneled packet
the checksum of the outer header is 'constant' (because with the
checksum field filled into the inner protocol header, the payload
of the outer frame checksums to 'zero'), and we can take advantage
of that in various ways. From Edward Cree"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1548 commits)
bonding: fix bond_get_stats()
net: bcmgenet: fix dma api length mismatch
net/mlx4_core: Fix backward compatibility on VFs
phy: mdio-thunder: Fix some Kconfig typos
lan78xx: add ndo_get_stats64
lan78xx: handle statistics counter rollover
RDS: TCP: Remove unused constant
RDS: TCP: Add sysctl tunables for sndbuf/rcvbuf on rds-tcp socket
net: smc911x: convert pxa dma to dmaengine
team: remove duplicate set of flag IFF_MULTICAST
bonding: remove duplicate set of flag IFF_MULTICAST
net: fix a comment typo
ethernet: micrel: fix some error codes
ip_tunnels, bpf: define IP_TUNNEL_OPTS_MAX and use it
bpf, dst: add and use dst_tclassid helper
bpf: make skb->tc_classid also readable
net: mvneta: bm: clarify dependencies
cls_bpf: reset class and reuse major in da
ldmvsw: Checkpatch sunvnet.c and sunvnet_common.c
ldmvsw: Add ldmvsw.c driver code
...
The success of CMA allocation largely depends on the success of
migration and key factor of it is page reference count. Until now, page
reference is manipulated by direct calling atomic functions so we cannot
follow up who and where manipulate it. Then, it is hard to find actual
reason of CMA allocation failure. CMA allocation should be guaranteed
to succeed so finding offending place is really important.
In this patch, call sites where page reference is manipulated are
converted to introduced wrapper function. This is preparation step to
add tracepoint to each page reference manipulation function. With this
facility, we can easily find reason of CMA allocation failure. There is
no functional change in this patch.
In addition, this patch also converts reference read sites. It will
help a second step that renames page._count to something else and
prevents later attempt to direct access to it (Suggested by Andrew).
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Calling dev_close() causes IFF_UP to be cleared which will remove the
interfaces routes and some addresses. That's probably not what the user
intended when running the offline selftest. Besides this does not happen
if the interface is brought down before the test, so the current
behaviour is inconsistent.
Instead call the net_device_ops ndo_stop function directly and avoid
touching IFF_UP at all.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Problem: When switching off VLAN offloading on an i350, the VLAN
interface gets unusable. For testing, set up a VLAN on an i350
and some remote machine, e.g.:
$ ip link add link eth0 name eth0.42 type vlan id 42
$ ip addr add 192.168.42.1/24 dev eth0.42
$ ip link set dev eth0.42 up
Offloading is switched on by default:
$ ethtool -k eth0 | grep vlan-offload
rx-vlan-offload: on
tx-vlan-offload: on
$ ping -c 3 -I eth0.42 192.168.42.2
[...works as usual...]
Now switch off VLAN offloading and try again:
$ ethtool -K eth0 rxvlan off
Actual changes:
rx-vlan-offload: off
tx-vlan-offload: off [requested on]
$ ping -c 3 -I eth0.42 192.168.42.2
PING 192.168.42.2 (192.168.42.2) from 192.168.42.1 eth0.42: 56(84) bytes of da
ta.
--- 192.168.42.2 ping statistics ---
3 packets transmitted, 0 received, 100% packet loss, time 1999ms
I can only reproduce it on an i350, the above works fine on a 82580.
While inspecting the igb source, I came across the code in igb_set_vmolr
which sets the E1000_VMOLR_STRVLAN/E1000_DVMOLR_STRVLAN flags once and
for all, and in all of the igb code there's no other place where the
STRVLAN is set or cleared. Thus, VLAN stripping is enabled in igb
unconditionally, independently of the offloading setting.
I compared that to the latest Intel igb-5.3.3.5 driver from
http://sourceforge.net/projects/e1000/ which in fact sets and clears the
STRVLAN flag independently from igb_set_vmolr in its own function
igb_set_vf_vlan_strip, depending on the vlan settings.
So I included the STRVLAN handling from the igb-5.3.3.5 driver into our
current igb driver and tested the above scenario again. This time ping
still works after switching off VLAN offloading.
Tested on i350, with and without addtional VFs, as well as on 82580
successfully.
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for generic Tx checksums to the igb driver. It
turns out this is actually pretty easy after going over the datasheet as we
were doing a number of steps we didn't need to.
In order to perform a Tx checksum for an L4 header we need to fill in the
following fields in the Tx descriptor:
MACLEN (maximum of 127), retrieved from:
skb_network_offset()
IPLEN (maximum of 511), retrieved from:
skb_checksum_start_offset() - skb_network_offset()
TUCMD.L4T indicates offset and if checksum or crc32c, based on:
skb->csum_offset
The added advantage to doing this is that we can support inner checksum
offloads for tunnels and MPLS while still being able to transparently
insert VLAN tags.
I also took the opportunity to clean-up many of the feature flag
configuration bits to make them a bit more consistent between drivers.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
E1000_MRQC_ENABLE_RSS_4Q enables 4 and 8 queues depending on the part
so rename to be generic.
Similarly, E1000_MRQC_ENABLE_VMDQ_RSS_2Q has no numeric meaning so
rename to be more generic.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In general case the maximum supported half cycle time of the synchronized
output clock is 70msec. Slower half cycle time than 70msec can be
programmed also as long as the output clock is synchronized to whole
seconds, useful specifically for generating a 1Hz clock.
Permitted values for the clock half cycle time are: 125,000,000 decimal,
250,000,000 decimal and 500,000,000 decimal (equals to 125msec, 250msec
and 500msec respectively).
Before this patch, only the half cycle time of less than or equal to 70msec
uses the I210 clock output function. This patch adds additional conditions
when half cycle time is equal to 125msec or 250msec or 500msec to use
clock output function.
Under other conditions, interrupt driven target time output events method
is still used to generate the desired clock output.
Signed-off-by: Roland Hii <roland.king.guan.hii@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Override EEPROM settings for specific OEM devices.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This e1000_phy_operations structure is never modified, so declare it as
const. Other structures of this type are already const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
I210 device IPv6 autoconf test sometimes fails,
because DAD NS for link-local is not transmitted.
This packet is silently dropped.
This problem is seen only GbE environment.
igb_watchdog_task link up detection continues to the following process.
The following cases are observed:
1.PHY 1000BASE-T Status Register Remote receiver status bit is NG.
(NG status becomes OK after about 200 - 700ms)
2.In this case, the transfer packet is silently dropped.
1000BASE-T Status register
[Expected]: 0x3800 or 0x7800
[problem occurred]: 0x2800 or 0x6800
Frequency of occurrence: approx 1/10 - 1/40 observed
In order to avoid this problem,
wait until 1000BASE-T Status register "Remote receiver status OK"
After applying this patch, at least 400 runs succeed with no problems.
Signed-off-by: Takuma Ueba <t.ueba11@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There was a workaround partially implemented for the 82576 that is needed
in order for VLAN tag stripping to function correctly. The original code
had side effects that would make it so the workaround was active on all
MACs. I have updated the code so that the workaround is enabled, but
limited to the 82576, or activated if we exceed the available unicast
addresses.
The workaround has a side effect of mirroring all of the traffic outgoing
from the VFs back to the PF. As such it is not recommended to use the
82576 in promiscuous mode as it will take a performance hit, though this is
now consistent with the performance as seen on the out-of-tree igb driver.
I also limited the scope of the UTA bits all being set to only when the
VMOLR register is enabled. This should limit the effects of the UTA
register so that we don't pick up any excess traffic unless promiscuous
mode has been enabled on the PF, whereas before the PF would have ended up
in something equivalent to unicast promiscuous mode with VLAN filtering
otherwise.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we can use the bridge utility to add a FDB
entry for the PF to an igb port. By doing this we can enable the VFs to
talk to virtual ports residing on top of the PF.
In addition this should also address issues with MACVLANs trying to reside
on top of the PF as well as they would have had similar issues when added
to the PF with SR-IOV enabled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch drops several checks that we dropped from ixgbe some ago. It
should not be possible for us to be called with either of the conditional
statements returning true so we can just drop them from the hot-path.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change fixes things so that we can fully support SR-IOV or the
recently added NTUPLE filtering while allowing support for VLAN promiscuous
mode. By making this change we are able to support possible scenarios such
as SR-IOV with the PF connected to a Linux bridge hosting other VMs.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to clean-up the configuration of the VF port based VLAN
configuration. The original logic was a bit muddled and had some
undesirable side effects such as VLANs being either completely stripped
from the port or VLANs being left when they shouldn't be. The idea behind
this code is to avoid any events such as spurious spoof notifications when
we are removing one VLAN tag and replacing it with another.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we can merge the configuration of the VLVF
registers into the setting of the VFTA register. By doing this we simplify
the logic and make use of similar functionality that we have already added
for ixgbe making it easier to maintain both drivers.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes it so that we always add VLAN 0. This is important as we
need to guarantee the PF can receive untagged frames in the case of SR-IOV
being enabled but VLAN filtering not being enabled in the kernel.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The RLPML registers already take the size of VLAN headers into account when
determining the maximum packet length. This is called out in EAS documents
for several parts including the 82576 and the i350. As such we can drop
the addition of size to the value programmed into the RLPML registers.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since the igb driver is using page based receive there is no point in
limiting the Rx capabilities of the device. The driver can receive 9K
jumbo frames at all times. The only changes needed due to MTU changes are
updates for the FIFO sizes and flow-control watermarks.
Update the maximum frame size to reflect the 9.5K limitation of the
hardware, and replace all instances of max_frame_size with
MAX_JUMBO_FRAME_SIZE when referring to an Rx FIFO or frame.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch starts the clean-up process on the VFTA configuration.
Specifically in this patch I attempt to address and simplify several items
while also updating the code to bring it more inline with what is already
in ixgbe.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Drop a bunch of hand written byte swapping code in favor of just doing the
byte swapping ourselves. The registers are little endian registers storing
a big endian value so if we read the MAC address array as little endian
then we will get the CPU registers into the proper layout.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver shouldn't just give up if it fails to get the hardware
mailbox lock. This can happen in a situation where the PF-VF
communication channel is heavily loaded and causes complete
communications failure between the PF and VF drivers.
Add a counter and a delay. The driver will now retry ten times, waiting
one millisecond between retries.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
By the commit 72ddef0506 ("igb: Fix oops caused by missing queue
pairing"), the IGB_FLAG_QUEUE_PAIRS flag can now be set when changing the
number of queues by "ethtool -L", but it is never cleared unless the igb
driver is reloaded.
This patch clears it if queue pairing becomes unnecessary as a result of
"ethtool -L".
Signed-off-by: Shota Suzuki <suzuki_shota_t3@lab.ntt.co.jp>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If VFs are enabled (max_vfs >= 1), both max_rss_queues and
adapter->rss_queues are set to 2 in the case of e1000_82576.
In this case, IGB_FLAG_QUEUE_PAIRS is always set in the default block as a
result of fall-through, thus setting it in the e1000_82576 block is not
necessary.
Signed-off-by: Shota Suzuki <suzuki_shota_t3@lab.ntt.co.jp>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The SCTP checksum is really a CRC and is very different from the
standards 1's complement checksum that serves as the checksum
for IP protocols. This offload interface is also very different.
Rename NETIF_F_SCTP_CSUM to NETIF_F_SCTP_CRC to highlight these
differences. The term CSUM should be reserved in the stack to refer
to the standard 1's complement IP checksum.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, the ethtool self-test gstrings/data arrays were accessed via
hardcoded indices, which made the code difficult to follow. This patch
replaces the hardcoded values with enum-based labels.
Signed-off-by: Joe Schultz <jschultz@xes-inc.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously, the PHY-specific code to get the cable length for the
I210 internal and related PHYs was reporting the cable length of a
single pair and reporting it as the min, max, and total cable length.
Update it so that all four pairs are checked so the true min, max,
and average cable lengths are reported.
Signed-off-by: Joe Schultz <jschultz@xes-inc.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is no reason to add the PHY address into the PCDL register address.
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The I210 internal PHY can be accessed just as well with the access
functions shared by 82580, I350, and I354 devices. A side effect of
relying on the common functions, is that I210 cable length support
is folded back into the common case which effectively reverts the
following commit:
commit 59f301046b
Author: Carolyn Wyborny <carolyn.wyborny@intel.com>
Date: Wed Oct 10 04:42:59 2012 +0000
igb: Update get cable length function for i210/i211
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clean up array_rd32 so that it uses igb_rd32 the same as rd32, per the
suggestion of Alexander Duyck, and use io_addr in more places, so that
we don't have the need to call E1000_REMOVED (which simply looks for a
null hw_addr) nearly as much.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The combined effect of commits 6423fc3416 ("igb: do not re-init SR-IOV
during probe") and ceee3450b3 ("igb: make sure SR-IOV init uses the
right number of queues") causes VFs no longer getting set up, leading
to NULL pointer dereferences due to the adapter's ->vf_data being NULL
while ->vfs_allocated_count is non-zero. The first commit not only
neglected the side effect of igb_sriov_reinit() that the second commit
tried to account for, but also that of setting IGB_FLAG_HAS_MSIX,
without which igb_enable_sriov() is effectively a no-op. Calling
igb_{,re}set_interrupt_capability() as done here seems to address this,
but I'm not sure whether this is better than sinply reverting the other
two commits.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i210 has two EEPROM access registers that are located in
non-standard offsets: EEARBC and EEMNGCTL. EEARBC was fixed previously
and EEMNGCTL should also be corrected.
Reported-by: Roman Hodek <roman.aud@siemens.com>
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As per Eric Dumazet's previous patches:
(see commit (24d2e4a507) - tg3: use napi_complete_done())
Quoting verbatim:
Using napi_complete_done() instead of napi_complete() allows
us to use /sys/class/net/ethX/gro_flush_timeout
GRO layer can aggregate more packets if the flush is delayed a bit,
without having to set too big coalescing parameters that impact
latencies.
</end quote>
Tested
configuration: low latency via ethtool -C ethx adaptive-rx off
rx-usecs 10 adaptive-tx off tx-usecs 15
workload: streaming rx using netperf TCP_MAERTS
igb:
MIGRATED TCP MAERTS TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.1 () port 0 AF_INET : demo
...
Interim result: 941.48 10^6bits/s over 1.000 seconds ending at 1440193171.589
Alignment Offset Bytes Bytes Recvs Bytes Sends
Local Remote Local Remote Xfered Per Per
Recv Send Recv Send Recv (avg) Send (avg)
8 8 0 0 1176930056 1475.36 797726 16384.00 71905
MIGRATED TCP MAERTS TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.1 () port 0 AF_INET : demo
...
Interim result: 941.49 10^6bits/s over 0.997 seconds ending at 1440193142.763
Alignment Offset Bytes Bytes Recvs Bytes Sends
Local Remote Local Remote Xfered Per Per
Recv Send Recv Send Recv (avg) Send (avg)
8 8 0 0 1175182320 50476.00 23282 16384.00 71816
i40e:
Hard to test because the traffic is incoming so fast (24Gb/s) that GRO
always receives 87kB, even at the highest interrupt rate.
Other drivers were only compile tested.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Many drivers initialize uselessly n_priv_flags, n_stats, testinfo_len,
eedump_len & regdump_len fields in their .get_drvinfo() ethtool op.
It's not necessary as these fields is filled in ethtool_get_drvinfo().
v2: removed unused variable
v3: removed another unused variable
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to deprecate the use of 'struct timespec' on 32-bit
architectures, as it is will overflow in 2038. The igb
driver uses it to read the current time, and can simply
be changed to use ktime_get_real_ts64() instead.
Because of hardware limitations, there is still an overflow
in year 2106, which we cannot really avoid, but this documents
the overflow.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Reviewed-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In igb_sw_init() the sequence of calls was changed from
igb_init_queue_configuration()
igb_init_interrupt_scheme()
igb_probe_vfs()
to
igb_probe_vfs()
igb_init_queue_configuration()
igb_init_interrupt_scheme()
This results in adapter->flags not having the IGB_FLAG_HAS_MSIX bit set
during igb_probe_vfs()->igb_enable_sriov(). Therefore SR-IOV does not
get enabled properly and we run into a NULL pointer if the max_vfs
module parameter is specified (adapter->vf_data does not get allocated,
crash on accessing the structure).
[ 7.419348] BUG: unable to handle kernel NULL pointer dereference at 0000000000000048
[ 7.419367] IP: [<ffffffffa02161c6>] igb_reset+0xe6/0x5d0 [igb]
[ 7.419370] PGD 0
[ 7.419373] Oops: 0002 [#1] SMP
[ 7.419381] Modules linked in: ahci(+) libahci igb(+) i40e(+) vxlan ip6_udp_tunnel udp_tunnel megaraid_sas(+) ixgbe(+) mdio
[ 7.419385] CPU: 0 PID: 4 Comm: kworker/0:0 Not tainted 4.2.0+ #153
[ 7.419387] Hardware name: Dell Inc. PowerEdge R720/0C4Y3R, BIOS 1.6.0 03/07/2013
[...]
[ 7.419431] Call Trace:
[ 7.419442] [<ffffffffa0217236>] igb_probe+0x8b6/0x1340 [igb]
[ 7.419447] [<ffffffff814c7f15>] local_pci_probe+0x45/0xa0
Prevent this by setting the IGB_FLAG_HAS_MSIX bit before calling
igb_probe_vfs(). The real interrupt capabilities will be checked during
igb_init_interrupt_scheme() so this is safe to do.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit c48a11c7ad ("netvm: propagate page->pfmemalloc to skb") added
checks for page->pfmemalloc to __skb_fill_page_desc():
if (page->pfmemalloc && !page->mapping)
skb->pfmemalloc = true;
It assumes page->mapping == NULL implies that page->pfmemalloc can be
trusted. However, __delete_from_page_cache() can set set page->mapping
to NULL and leave page->index value alone. Due to being in union, a
non-zero page->index will be interpreted as true page->pfmemalloc.
So the assumption is invalid if the networking code can see such a page.
And it seems it can. We have encountered this with a NFS over loopback
setup when such a page is attached to a new skbuf. There is no copying
going on in this case so the page confuses __skb_fill_page_desc which
interprets the index as pfmemalloc flag and the network stack drops
packets that have been allocated using the reserves unless they are to
be queued on sockets handling the swapping which is the case here and
that leads to hangs when the nfs client waits for a response from the
server which has been dropped and thus never arrive.
The struct page is already heavily packed so rather than finding another
hole to put it in, let's do a trick instead. We can reuse the index
again but define it to an impossible value (-1UL). This is the page
index so it should never see the value that large. Replace all direct
users of page->pfmemalloc by page_is_pfmemalloc which will hide this
nastiness from unspoiled eyes.
The information will get lost if somebody wants to use page->index
obviously but that was the case before and the original code expected
that the information should be persisted somewhere else if that is
really needed (e.g. what SLAB and SLUB do).
[akpm@linux-foundation.org: fix blooper in slub]
Fixes: c48a11c7ad ("netvm: propagate page->pfmemalloc to skb")
Signed-off-by: Michal Hocko <mhocko@suse.com>
Debugged-by: Vlastimil Babka <vbabka@suse.com>
Debugged-by: Jiri Bohac <jbohac@suse.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: <stable@vger.kernel.org> [3.6+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recent changes to igb_probe_vfs() could lead to the PF holding onto all
of the queues. Reorder igb_probe_vfs() to be before
gb_init_queue_configuration() and add some more error checking.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In error handling code of igb_probe, the memory adapter->shadow_vfta
allocated by kcalloc in igb_sw_init is not freed. So when register_netdev
or igb_init_i2c is failed, a memory leak will occur.
This patch adds kfree to fix it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When igb_init_interrupt_scheme in igb_sriov_reinit is failed, the lock
acquired by rtnl_lock() is not released, which causes a deadlock.
This patch adds rtnl_unlock() in error handling to fix it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the .remove() callback for a PF is called, SR-IOV support for the
device is disabled, which requires unbinding and removing the VFs.
The VFs may be in-use either by the host kernel or userspace, such as
assigned to a VM through vfio-pci. In this latter case, the VFs may
be removed either by shutting down the VM or hot-unplugging the
devices from the VM. Unfortunately in the case of a Windows 2012 R2
guest, hot-unplug is broken due to the ordering of the PF driver
teardown. Disabling SR-IOV prior to unregister_netdev() avoids this
issue.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for Marvell PHY 1512 (required for I354).
Submitted by: Maciej Szwed <maciej.szwed@intel.com>
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In addition to interrupt driven target time output events, the i210
also has two programmable clock outputs. These clocks support periods
between 16 nanoseconds and 140 milliseconds. This patch implements
the periodic output function using the clock outputs when possible,
falling back to the target time for longer periods.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During driver probing the following code path is triggered.
igb_probe
->igb_sw_init
->igb_probe_vfs
->igb_pci_enable_sriov
->igb_sriov_reinit
Doing the SR-IOV re-init is not necessary during probing since we're
starting from scratch. Here we can call igb_enable_sriov() right away.
Running igb_sriov_reinit() during igb_probe() also seems to cause
occasional packet loss on some onboard 82576 NICs. Reproduced on
Dell and HP servers with onboard 82576 NICs.
Example:
Intel Corporation 82576 Gigabit Network Connection [8086:10c9] (rev 01)
Subsystem: Dell Device [1028:0481]
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When initializing igb driver (e.g. 82576, I350), IGB_FLAG_QUEUE_PAIRS is
set if adapter->rss_queues exceeds half of max_rss_queues in
igb_init_queue_configuration().
On the other hand, IGB_FLAG_QUEUE_PAIRS is not set even if the number of
queues exceeds half of max_combined in igb_set_channels() when changing
the number of queues by "ethtool -L".
In this case, if numvecs is larger than MAX_MSIX_ENTRIES (10), the size
of adapter->msix_entries[], an overflow can occur in
igb_set_interrupt_capability(), which in turn leads to an oops.
Fix this problem as follows:
- When changing the number of queues by "ethtool -L", set
IGB_FLAG_QUEUE_PAIRS in the same way as initializing igb driver.
- When increasing the size of q_vector, reallocate it appropriately.
(With IGB_FLAG_QUEUE_PAIRS set, the size of q_vector gets larger.)
Another possible way to fix this problem is to cap the queues at its
initial number, which is the number of the initial online cpus. But this
is not the optimal way because we cannot increase queues when another
cpu becomes online.
Note that before commit cd14ef54d2 ("igb: Change to use statically
allocated array for MSIx entries"), this problem did not cause oops
but just made the number of queues become 1 because of entering msi_only
mode in igb_set_interrupt_capability().
Fixes: 907b783579 ("igb: Add ethtool support to configure number of channels")
CC: stable <stable@vger.kernel.org>
Signed-off-by: Shota Suzuki <suzuki_shota_t3@lab.ntt.co.jp>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the ARRAY_SIZE macro rather than calculating sizeof(a)/sizeof(a[0]).
Also directly replace the code rather than using an unnecessary define.
Reported-by: Maninder Singh <maninder1.s@samsung.com>
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are many settings possible using ethtool -C/--coalesce, but not
all of them are supported in igb. Report failure when an unsupported
option is set.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
e1000_check_for_link_media_swap() checks PHY page 0 for copper and PHY
page 1 for "other" (fiber) link. The switch back from page 1 to page 0
happened too soon, before e1000_check_for_link_82575() is executed, and
link on fiber (other) was never detected. Check for link while still on
the proper PHY page.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we pull the timestamp from the fragment before
we add it to the skb. By doing this we can avoid a possible issue in which
the fragment can possibly be less than IGB_RX_HDR_LEN due to the timestamp
being pulled after the copybreak check.
While making this change I realized we could also pull the rest of the
igb_pull_tail function into igb_add_rx_frag since in the case of igb,
unlike ixgbe, we are able to unmap the entire buffer before calling
add_rx_frag so merging the two allows for sharing of code between the two
merged functions.
Reported-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump version of igb to igb-5.2.18
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Disable IPv6 extension header processing as per hardware errata.
Also fix copyright date.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When programming the start of a periodic output, the code wrongly places
the seconds value into the "low" register and the nanoseconds into the
"high" register. Even though this is backwards, it slipped through my
testing, because the re-arming code in the interrupt service routine is
correct, and the signal does appear starting with the second edge.
This patch fixes the issue by programming the registers correctly.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Four minor merge conflicts:
1) qca_spi.c renamed the local variable used for the SPI device
from spi_device to spi, meanwhile the spi_set_drvdata() call
got moved further up in the probe function.
2) Two changes were both adding new members to codel params
structure, and thus we had overlapping changes to the
initializer function.
3) 'net' was making a fix to sk_release_kernel() which is
completely removed in 'net-next'.
4) In net_namespace.c, the rtnl_net_fill() call for GET operations
had the command value fixed, meanwhile 'net-next' adjusted the
argument signature a bit.
This also matches example merge resolutions posted by Stephen
Rothwell over the past two days.
Signed-off-by: David S. Miller <davem@davemloft.net>
This change updates igb so that it will correctly perform the descriptor
count calculation. Previously it was taking NETDEV_FRAG_PAGE_MAX_SIZE
into account with isn't really correct since a different value is used to
determine the size of the pages used for TCP. That is actually determined
by SKB_FRAG_PAGE_ORDER.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
adapter->tx_ring is set to NULL where rx_ring should be.
Fixes: 5536d2102a ("igb: Combine q_vector and ring allocation into a single function")
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When changing the number of rings by ethtool -L, q_vectors are reused,
which causes oops because of uninitialized pointers.
- When an rx is reused as a tx, q_vector->rx.ring is not set to NULL, which
misleads igb_poll() to determine that it has an rx ring although it
actually points to the tx ring.
- When a tx is reused as an rx, q_vector->rx.ring->skb
(q_vector->ring[0].skb) has a value that was used as tx_stats before.
Fix these problems by zeroing it out on reuseing it.
Fixes: 02ef6e1d0b ("igb: Fix queue allocation method to accommodate changing during runtime")
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
igb_enable_mas() should only be called for the 82575 and has no clear
return so changing it to void. Also simplify the odd conditional
expression.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch changes the driver to use ns_to_timespec64() and
timespec64_to_ns() instead of open coding the same logic.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed two warnings in e1000e and igb, when switching to timespec64
some printf formats started to not match. In theses cases actually
the new type is __kernel_time_t which is __kernel_long_t which
unfortunately can be either "long" or "long long". So to solve
this I cases the arguments to "long long". -DaveM
Richard Cochran says:
====================
ptp: get ready for 2038
This series converts the core driver methods of the PTP Hardware Clock
(PHC) subsystem to use the 64 bit version of the timespec structure,
making the core API ready for the year 2038.
In addition, I reviewed how each driver and device represents the time
value at the hardware register level. Most of the drivers are ready,
but a few will need some work before the year 2038, as shown:
Patch Driver
------------------------------------------------
12 drivers/net/ethernet/intel/igb/igb_ptp.c
15 ? drivers/net/ethernet/sfc/ptp.c
16 drivers/net/ethernet/stmicro/stmmac/stmmac_ptp.c
The commit log messages document how each driver is ready or why it is
not ready. For patch 15, I could not easily find out the hardware
representation of the time value, and so the SFC maintainers will have
to review their low level code in order to resolve any remaining
issues.
* ChangeLog
** V3
- dp83640: use timespec64 throughout per Arnd's suggestion
- tilegx: use timespec64 throughout per Chris' suggestion
- add Jeff's acked-bys
** V2
- use the new methods in the posix clock code right away (patch #3)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
