The pnv_ioda_pe struct keeps an array of peers. At the moment it is only
used to link GPU and NPU for 2 purposes:
1. Access NPU quickly when configuring DMA for GPU - this was addressed
in the previos patch by removing use of it as DMA setup is not what
the kernel would constantly do.
2. Invalidate TCE cache for NPU when it is invalidated for GPU.
GPU and NPU are in different PE. There is already a mechanism to
attach multiple iommu_table_group to the same iommu_table (used for VFIO),
we can reuse it here so does this patch.
This gets rid of peers[] array and PNV_IODA_PE_PEER flag as they are
not needed anymore.
While we are here, add TCE cache invalidation after enabling bypass.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-By: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The upcoming NVLink passthrough support will require NPU code to cope
with two DMA windows.
This adds a pnv_npu_set_window() helper which programs 32bit window to
the hardware. This also adds multilevel TCE support.
This adds a pnv_npu_unset_window() helper which removes the DMA window
from the hardware. This does not make difference now as the caller -
pnv_npu_dma_set_bypass() - enables bypass in the hardware but the next
patch will use it to manage TCE table lists for TCE Kill handling.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-By: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This exports debugging helper pe_level_printk() and corresponding macroses
so they can be used in npu-dma.c.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-By: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
NPU devices are emulated in firmware and mainly used for NPU NVLink
training; one NPU device is per a hardware link. Their DMA/TCE setup
must match the GPU which is connected via PCIe and NVLink so any changes
to the DMA/TCE setup on the GPU PCIe device need to be propagated to
the NVLink device as this is what device drivers expect and it doesn't
make much sense to do anything else.
This makes NPU DMA setup explicit.
pnv_npu_ioda_controller_ops::pnv_npu_dma_set_mask is moved to pci-ioda,
made static and prints warning as dma_set_mask() should never be called
on this function as in any case it will not configure GPU; so we make
this explicit.
Instead of using PNV_IODA_PE_PEER and peers[] (which the next patch will
remove), we test every PCI device if there are corresponding NVLink
devices. If there are any, we propagate bypass mode to just found NPU
devices by calling the setup helper directly (which takes @bypass) and
avoid guessing (i.e. calculating from DMA mask) whether we need bypass
or not on NPU devices. Since DMA setup happens in very rare occasion,
this will not slow down booting or VFIO start/stop much.
This renames pnv_npu_disable_bypass to pnv_npu_dma_set_32 to make it
more clear what the function really does which is programming 32bit
table address to the TVT ("disabling bypass" means writing zeroes to
the TVT).
This removes pnv_npu_dma_set_bypass() from pnv_npu_ioda_fixup() as
the DMA configuration on NPU does not matter until dma_set_mask() is
called on GPU and that will do the NPU DMA configuration.
This removes phb->dma_dev_setup initialization for NPU as
pnv_pci_ioda_dma_dev_setup is no-op for it anyway.
This stops using npe->tce_bypass_base as it never changes and values
other than zero are not supported.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This uses the page size from iommu_table instead of hard-coded 4K.
This should cause no change in behavior.
While we are here, move bits around to prepare for further rework
which will define and use iommu_table_group_ops.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
NPU PHB TCE Kill register is exactly the same as in the rest of POWER8
so let's reuse the existing code for NPU. The only bit missing is
a helper to reset the entire TCE cache so this moves such a helper
from NPU code and renames it.
Since pnv_npu_tce_invalidate() does really invalidate the entire cache,
this uses pnv_pci_ioda2_tce_invalidate_entire() directly for NPU.
This adds an explicit comment for workaround for invalidating NPU TCE
cache.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This replaces magic constants for TCE Kill IODA2 register with macros.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
As in fact pnv_pci_ioda2_tce_invalidate_entire() invalidates TCEs for
the specific PE rather than the entire cache, rename it to
pnv_pci_ioda2_tce_invalidate_pe(). In later patches we will add
a proper pnv_pci_ioda2_tce_invalidate_entire().
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The function pnv_pci_reset_secondary_bus() is called like below.
It's impossible for call the function on root bus. So it's safe
to remove the root bus case in the function. No functional changes
introduced.
pci_parent_bus_reset() / pci_bus_reset() / pci_try_reset_bus()
pci_reset_bridge_secondary_bus()
pcibios_reset_secondary_bus()
pnv_pci_reset_secondary_bus()
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This drops unnecessary nested if statements in pnv_eeh_reset() to
improve the code readability. After the changes, the unused local
variable "ret" is dropped as well. No logical changes introduced.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In current implementation, the PEs that are allocated or picked
from the reserved list are identified by PE number. The PE instance
has to be picked according to the PE number eventually. We have
same issue when PE is released.
For pnv_ioda_pick_m64_pe() and pnv_ioda_alloc_pe(), this returns
PE instance so that pnv_ioda_setup_bus_PE() can use the allocated
or reserved PE instance directly. Also, pnv_ioda_setup_bus_PE()
returns the reserved/allocated PE instance to be used in subsequent
patches. On the other hand, pnv_ioda_free_pe() uses PE instance
(not number) as its argument. No logical changes introduced.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In current implementation, the DMA32 segments required by one specific
PE isn't calculated with the information hold in the PE independently.
It conflicts with the PCI hotplug design: PE centralized, meaning the
PE's DMA32 segments should be calculated from the information hold in
the PE independently.
This introduces an array (@dma32_segmap) for every PHB to track the
DMA32 segmeng usage. Besides, this moves the logic calculating PE's
consumed DMA32 segments to pnv_pci_ioda1_setup_dma_pe() so that PE's
DMA32 segments are calculated/allocated from the information hold in
the PE (DMA32 weight). Also the logic is improved: we try to allocate
as much DMA32 segments as we can. It's acceptable that number of DMA32
segments less than the expected number are allocated.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PEs are put into PHB DMA32 list (phb->ioda.pe_dma_list) according
to their DMA32 weight. The PEs on the list are iterated to setup
their TCE32 tables at system booting time. The list is used for
once at boot time and no need to keep it.
This moves the logic calculating DMA32 weight of PHB and PE to
pnv_ioda_setup_dma() to drop PHB's DMA32 list. Also, every PE
traces the consumed DMA32 segment by @tce32_seg and @tce32_segcount
are useless and they're removed.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently, there is one macro (TCE32_TABLE_SIZE) representing the
TCE table size for one DMA32 segment. The constant representing
the DMA32 segment size (1 << 28) is still used in the code.
This defines PNV_IODA1_DMA32_SEGSIZE representing one DMA32
segment size. the TCE table size can be calcualted when the page
has fixed 4KB size. So all the related calculation depends on one
macro (PNV_IODA1_DMA32_SEGSIZE). No logical changes introduced.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-By: Alistair Popple <alistair@popple.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This renames pnv_pci_ioda_setup_dma_pe() to pnv_pci_ioda1_setup_dma_pe()
as it's the counter-part of IODA2's pnv_pci_ioda2_setup_dma_pe().
No logical changes introduced.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This enables M64 window on P7IOC, which has been enabled on PHB3.
Different from PHB3 where 16 M64 BARs are supported and each of
them can be owned by one particular PE# exclusively or divided
evenly to 256 segments, every P7IOC PHB has 16 M64 BARs and each
of them are divided to 8 segments. So every P7IOC PHB supports
128 M64 segments in total. P7IOC has M64DT, which helps mapping
one particular M64 segment# to arbitrary PE#. PHB3 doesn't have
M64DT, indicating that one M64 segment can only be pinned to the
fixed PE#.
In order to unified M64 support M64 on P7IOC and PHB3, we just
provide 128 M64 segments on every P7IOC PHB and each of them is
pinned to the fixed PE# by bypassing the function of M64DT. In
turn, we just need different phb->init_m64() for P7IOC and PHB3
and maps M64 segment in pnv_ioda_reserve_m64_pe() for P7IOC, most
of the code are shared by them.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Alistair Popple <alistair@popple.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This renames those functions picking PE number based on consumed
M64 segments, mapping M64 segments to PEs as those functions are
going to be shared by IODA1/IODA2 in next patch. No logical changes
introduced.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When unplugging PCI devices, their parent PEs might be offline.
The consumed M64 resource by the PEs should be released at that
time. As we track M32 segment consumption, this introduces an
array to the PHB to track the mapping between M64 segment and
PE number.
Note: M64 mapping isn't covered by pnv_ioda_setup_pe_seg() as
IODA2 doesn't support the mapping explicitly while it's supported
on IODA1. Until now, no M64 is supported on IODA1 in software.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently, the IO and M32 segments are mapped to the corresponding
PE based on the windows of the parent bridge of PE's primary bus.
It's not going to work when the windows of root port or upstream
port of the PCIe switch behind root port are extended to PHB's
apertures in order to support hotplug in subsequent patch.
This fixes the issue by mapping IO and M32 segments based on the
resources of the PCI devices included in the PE, instead of the
windows of the parent bridge of the PE's primary bus.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
pnv_ioda_setup_pe_seg() associates the IO and M32 segments with the
owner PE. The code mapping segments should be fixed and immune from
logic changes introduced to pnv_ioda_setup_pe_seg().
This moves the code mapping segments to helper pnv_ioda_setup_pe_res().
The data type for @rc is changed to "int64_t". Also, argument @hose is
removed from pnv_ioda_setup_pe() as it can be got from @pe. No functional
changes introduced.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-By: Alistair Popple <alistair@popple.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There are two arrays for IO and M32 segment maps on every PHB.
The index of the arrays are segment number and the value stored
in the corresponding element is PE number, indicating the segment
is assigned to the PE. Initially, all elements in those two arrays
are zeroes, meaning all segments are assigned to PE#0. It's wrong.
This fixes the initial values in the elements of those two arrays
to IODA_INVALID_PE, meaning all segments aren't assigned to any
PE.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This changes the data type of PE number from "int" to "unsigned int"
in order to match the fact PE number is never negative:
* The number of PE to which the specified PCI device is attached.
* The PE number map for SRIOV VFs.
* The returned PE number from pnv_ioda_alloc_pe().
* The returned PE number from pnv_ioda2_pick_m64_pe().
Suggested-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-By: Alistair Popple <alistair@popple.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This renames the fields related to PE number in "struct pnv_phb"
for better reflecting of their usages as Alexey suggested. No
logical changes introduced.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This moves those fields in struct pnv_phb that are related to PE
allocation around. No logical change.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The last usage of pnv_phb::bdfn_to_pe() was removed in
ff57b454dd ("powerpc/eeh: Do probe on pci_dn"), so drop it.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This cleans up on below data struct instances to use tab instead of
space indent of statement to avoid complains from scripts/checkpatch.pl.
No logical changes introduced.
@pnv_pci_ioda_controller_ops
@pnv_npu_ioda_controller_ops
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When cfg_dbg() is enabled (i.e. mapped to printk()), gcc produces
errors as the __func__ parameter is missing (pnv_pci_cfg_read() has one);
this adds the missing parameter.
cfg_dbg() is just an inferior version of pr_devel() so use the latter
instead.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds routines for early setup for radix. We use device tree
property "ibm,processor-radix-AP-encodings" to find supported page
sizes. If we don't find the above we consider 64K and 4K as supported
page sizes.
We do map vmemap using 2M page size if we can. The linear mapping is
done such that we use required page size for that range. For example
memory of 3.5G is mapped such that we use 1G mapping till 3G range and
use 2M mapping for the rest.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The HMI code knows about three types of errors: CORE, NX and UNKNOWN.
If OPAL were to add a new type, it would not be handled at all since
there is no fallback case. Instead of explicitly checking for UNKNOWN,
treat any checkstop type without a handler as unknown.
Signed-off-by: Russell Currey <ruscur@russell.cc>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
After PE reset, OPAL API opal_pci_reinit() is called on all devices
contained in the PE to reinitialize them. While skiboot is not aware of
VFs, we have to implement the function in kernel to reinitialize VFs after
reset on PE for VFs.
In this patch, two functions pnv_pci_fixup_vf_mps() and
pnv_eeh_restore_vf_config() both manipulate the MPS of the VF, since for a
VF it has three cases.
1. Normal creation for a VF
In this case, pnv_pci_fixup_vf_mps() is called to make the MPS a proper
value compared with its parent.
2. EEH recovery without VF removed
In this case, MPS is stored in pci_dn and pnv_eeh_restore_vf_config() is
called to restore it and reinitialize other part.
3. EEH recovery with VF removed
In this case, VF will be removed then re-created. Both functions are
called. First pnv_pci_fixup_vf_mps() is called to store the proper MPS
to pci_dn and then pnv_eeh_restore_vf_config() is called to do proper
thing.
This introduces two functions: pnv_pci_fixup_vf_mps() to fixup the VF's
MPS to make sure it is equal to parent's and store this value in pci_dn
for future use. pnv_eeh_restore_vf_config() to re-initialize on VF by
restoring MPS, disabling completion timeout, enabling SERR, etc.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PEs for VFs don't have primary bus. So they have to have their own reset
backend, which is used during EEH recovery. The patch implements the reset
backend for VF's PE by issuing FLR or AF FLR to the VFs, which are contained
in the PE.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This creates PEs for VFs in the weak function pcibios_bus_add_device().
Those PEs for VFs are identified with newly introduced flag EEH_PE_VF
so that we treat them differently during EEH recovery.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
- eeh: Fix partial hotplug criterion from Gavin Shan
- mm: Clear the invalid slot information correctly from Aneesh Kumar K.V
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=bk3U
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.5-4' into next
Pull in our current fixes from 4.5, in particular the "Fix Multi hit
ERAT" bug is causing folks some grief when testing next.
Subcores isn't really part of the 2.07 architecture but currently we
turn it on using the 2.07 feature bit. Subcores is really a POWER8
specific feature.
This adds a new CPU_FTR bit just for subcores and moves the subcore
init code over to use this.
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When initialising OPAL interfaces, there is a possibility that
opal_msglog_init() may fail to initialise the msglog/memory console.
Fix opal_msglog_sysfs_init() so it doesn't try to create sysfs entry for
the msglog if this occurs.
Suggested-by: Joel Stanley <joel@jms.id.au>
Fixes: 9b4fffa149 ("powerpc/powernv: new function to access OPAL msglog")
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Quite often drivers set only "write" permission assuming that this
includes "read" permission as well and this works on plenty of
platforms. However IODA2 is strict about this and produces an EEH when
"read" permission is not set and reading happens.
This adds a workaround in the IODA code to always add the "read" bit
when the "write" bit is set.
Fixes: 10b35b2b74 ("powerpc/powernv: Do not set "read" flag if direction==DMA_NONE")
Cc: stable@vger.kernel.org # 4.2+
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Tested-by: Douglas Miller <dougmill@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When PCI bus is unplugged during full hotplug for EEH recovery,
the platform PE instance (struct pnv_ioda_pe) isn't released and
it dereferences the stale PCI bus that has been released. It leads
to kernel crash when referring to the stale PCI bus.
This fixes the issue by correcting the PE's primary bus when it's
oneline at plugging time, in pnv_pci_dma_bus_setup() which is to
be called by pcibios_fixup_bus().
Cc: stable@vger.kernel.org # v4.1+
Reported-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reported-by: Pradipta Ghosh <pradghos@in.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Tested-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When PE is created, its primary bus is cached to pe->bus. At later
point, the cached primary bus is returned from eeh_pe_bus_get().
However, we could get stale cached primary bus and run into kernel
crash in one case: full hotplug as part of fenced PHB error recovery
releases all PCI busses under the PHB at unplugging time and recreate
them at plugging time. pe->bus is still dereferencing the PCI bus
that was released.
This adds another PE flag (EEH_PE_PRI_BUS) to represent the validity
of pe->bus. pe->bus is updated when its first child EEH device is
online and the flag is set. Before unplugging in full hotplug for
error recovery, the flag is cleared.
Fixes: 8cdb2833 ("powerpc/eeh: Trace PCI bus from PE")
Cc: stable@vger.kernel.org #v3.11+
Reported-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reported-by: Pradipta Ghosh <pradghos@in.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Tested-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When M64 BAR is set to Single PE mode, the PE# assigned to VF could be
sparse.
This patch restructures the code to allocate sparse PE# for VFs when M64
BAR is set to Single PE mode. Also it rename the offset to pe_num_map to
reflect the content is the PE number.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Each VF could have 6 BARs at most. When the total BAR size exceeds the
gate, after expanding it will also exhaust the M64 Window.
This patch limits the boundary by checking the total VF BAR size instead of
the individual BAR.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
At the moment 64bit-prefetchable window can be maximum 64GB, which is
currently got from device tree. This means that in shared mode the maximum
supported VF BAR size is 64GB/256=256MB. While this size could exhaust the
whole 64bit-prefetchable window. This is a design decision to set a
boundary to 64MB of the VF BAR size. Since VF BAR size with 64MB would
occupy a quarter of the 64bit-prefetchable window, this is affordable.
This patch replaces magic limit of 64MB with "gate", which is 1/4 of the
M64 Segment Size(m64_segsize >> 2) and adds comment to explain the reason
for it.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Reviewed-by: Gavin Shan <gwshan@linux.vent.ibm.com>
Acked-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In current implementation, when VF BAR is bigger than 64MB, it uses 4 M64
BARs in Single PE mode to cover the number of VFs required to be enabled.
By doing so, several VFs would be in one VF Group and leads to interference
between VFs in the same group.
And in this patch, m64_wins is renamed to m64_map, which means index number
of the M64 BAR used to map the VF BAR. Based on Gavin's comments. Also
makes sure the VF BAR size is bigger than 32MB when M64 BAR is used in
Single PE mode.
This patch changes the design by using one M64 BAR in Single PE mode for
one VF BAR. This gives absolute isolation for VFs.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The alignment of IOV BAR on PowerNV platform is the total size of the IOV
BAR. No matter whether the IOV BAR is extended with number of
roundup_pow_of_two(total_vfs) or number of max PE number (256), the total
size could be calculated by (vfs_expanded * VF_BAR_size).
This patch simplifies the pnv_pci_iov_resource_alignment() by removing the
first case.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On PHB3, we enable SRIOV devices by mapping IOV BAR with M64 BARs. If a
SRIOV device's IOV BAR is not 64bit-prefetchable, this is not assigned from
64bit prefetchable window, which means M64 BAR can't work on it.
The reason is PCI bridges support only 2 memory windows and the kernel code
programs bridges in the way that one window is 32bit-nonprefetchable and
the other one is 64bit-prefetchable. So if devices' IOV BAR is 64bit and
non-prefetchable, it will be mapped into 32bit space and therefore M64
cannot be used for it.
This patch makes this explicit and truncate IOV resource in this case to
save MMIO space.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The EEH debugfs handlers have same prototype. This introduces
a macro to define them, then to simplify the code. No logical
changes.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently, the OPAL msglog/console buffer is exposed as a sysfs file, with
the sysfs read handler responsible for retrieving the log from the OPAL
buffer. We'd like to be able to use it in xmon as well.
Refactor the OPAL msglog code to create a new function, opal_msglog_copy(),
that copies to an arbitrary buffer. Separate the initialisation code into
generic memcons init and sysfs file creation.
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
"p5ioc2 is used by approximately 2 machines in the world, and has never
ever been a supported configuration."
The code for p5ioc2 is essentially unused and complicates what is already
a very complicated codebase. Its removal is essentially a "free win" in
the effort to simplify the powernv PCI code.
In addition, support for p5ioc2 has been dropped from skiboot. There's no
reason to keep it around in the kernel.
Signed-off-by: Russell Currey <ruscur@russell.cc>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
- Ground work for the new Power9 MMU from Aneesh Kumar K.V
- Optimise FP/VMX/VSX context switching from Anton Blanchard
- Various cleanups from Krzysztof Kozlowski, John Ogness, Rashmica Gupta,
Russell Currey, Gavin Shan, Daniel Axtens, Michael Neuling, Andrew Donnellan
- Allow wrapper to work on non-english system from Laurent Vivier
- Add rN aliases to the pt_regs_offset table from Rashmica Gupta
- Fix module autoload for rackmeter & axonram drivers from Luis de Bethencourt
- Include KVM guest test in all interrupt vectors from Paul Mackerras
- Fix DSCR inheritance over fork() from Anton Blanchard
- Make value-returning atomics & {cmp}xchg* & their atomic_ versions fully ordered from Boqun Feng
- Print MSR TM bits in oops messages from Michael Neuling
- Add TM signal return & invalid stack selftests from Michael Neuling
- Limit EPOW reset event warnings from Vipin K Parashar
- Remove the Cell QPACE code from Rashmica Gupta
- Append linux_banner to exception information in xmon from Rashmica Gupta
- Add selftest to check if VSRs are corrupted from Rashmica Gupta
- Remove broken GregorianDay() from Daniel Axtens
- Import Anton's context_switch2 benchmark into selftests from Michael Ellerman
- Add selftest script to test HMI functionality from Daniel Axtens
- Remove obsolete OPAL v2 support from Stewart Smith
- Make enter_rtas() private from Michael Ellerman
- PPR exception cleanups from Michael Ellerman
- Add page soft dirty tracking from Laurent Dufour
- Add support for Nvlink NPUs from Alistair Popple
- Add support for kexec on 476fpe from Alistair Popple
- Enable kernel CPU dlpar from sysfs from Nathan Fontenot
- Copy only required pieces of the mm_context_t to the paca from Michael Neuling
- Add a kmsg_dumper that flushes OPAL console output on panic from Russell Currey
- Implement save_stack_trace_regs() to enable kprobe stack tracing from Steven Rostedt
- Add HWCAP bits for Power9 from Michael Ellerman
- Fix _PAGE_PTE breaking swapoff from Aneesh Kumar K.V
- Fix _PAGE_SWP_SOFT_DIRTY breaking swapoff from Hugh Dickins
- scripts/recordmcount.pl: support data in text section on powerpc from Ulrich Weigand
- Handle R_PPC64_ENTRY relocations in modules from Ulrich Weigand
- cxl: Fix possible idr warning when contexts are released from Vaibhav Jain
- cxl: use correct operator when writing pcie config space values from Andrew Donnellan
- cxl: Fix DSI misses when the context owning task exits from Vaibhav Jain
- cxl: fix build for GCC 4.6.x from Brian Norris
- cxl: use -Werror only with CONFIG_PPC_WERROR from Brian Norris
- cxl: Enable PCI device ID for future IBM CXL adapter from Uma Krishnan
- Freescale updates from Scott: Highlights include moving QE code out of
arch/powerpc (to be shared with arm), device tree updates, and minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=R5bX
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Core:
- Ground work for the new Power9 MMU from Aneesh Kumar K.V
- Optimise FP/VMX/VSX context switching from Anton Blanchard
Misc:
- Various cleanups from Krzysztof Kozlowski, John Ogness, Rashmica
Gupta, Russell Currey, Gavin Shan, Daniel Axtens, Michael Neuling,
Andrew Donnellan
- Allow wrapper to work on non-english system from Laurent Vivier
- Add rN aliases to the pt_regs_offset table from Rashmica Gupta
- Fix module autoload for rackmeter & axonram drivers from Luis de
Bethencourt
- Include KVM guest test in all interrupt vectors from Paul Mackerras
- Fix DSCR inheritance over fork() from Anton Blanchard
- Make value-returning atomics & {cmp}xchg* & their atomic_ versions
fully ordered from Boqun Feng
- Print MSR TM bits in oops messages from Michael Neuling
- Add TM signal return & invalid stack selftests from Michael Neuling
- Limit EPOW reset event warnings from Vipin K Parashar
- Remove the Cell QPACE code from Rashmica Gupta
- Append linux_banner to exception information in xmon from Rashmica
Gupta
- Add selftest to check if VSRs are corrupted from Rashmica Gupta
- Remove broken GregorianDay() from Daniel Axtens
- Import Anton's context_switch2 benchmark into selftests from
Michael Ellerman
- Add selftest script to test HMI functionality from Daniel Axtens
- Remove obsolete OPAL v2 support from Stewart Smith
- Make enter_rtas() private from Michael Ellerman
- PPR exception cleanups from Michael Ellerman
- Add page soft dirty tracking from Laurent Dufour
- Add support for Nvlink NPUs from Alistair Popple
- Add support for kexec on 476fpe from Alistair Popple
- Enable kernel CPU dlpar from sysfs from Nathan Fontenot
- Copy only required pieces of the mm_context_t to the paca from
Michael Neuling
- Add a kmsg_dumper that flushes OPAL console output on panic from
Russell Currey
- Implement save_stack_trace_regs() to enable kprobe stack tracing
from Steven Rostedt
- Add HWCAP bits for Power9 from Michael Ellerman
- Fix _PAGE_PTE breaking swapoff from Aneesh Kumar K.V
- Fix _PAGE_SWP_SOFT_DIRTY breaking swapoff from Hugh Dickins
- scripts/recordmcount.pl: support data in text section on powerpc
from Ulrich Weigand
- Handle R_PPC64_ENTRY relocations in modules from Ulrich Weigand
cxl:
- cxl: Fix possible idr warning when contexts are released from
Vaibhav Jain
- cxl: use correct operator when writing pcie config space values
from Andrew Donnellan
- cxl: Fix DSI misses when the context owning task exits from Vaibhav
Jain
- cxl: fix build for GCC 4.6.x from Brian Norris
- cxl: use -Werror only with CONFIG_PPC_WERROR from Brian Norris
- cxl: Enable PCI device ID for future IBM CXL adapter from Uma
Krishnan
Freescale:
- Freescale updates from Scott: Highlights include moving QE code out
of arch/powerpc (to be shared with arm), device tree updates, and
minor fixes"
* tag 'powerpc-4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (149 commits)
powerpc/module: Handle R_PPC64_ENTRY relocations
scripts/recordmcount.pl: support data in text section on powerpc
powerpc/powernv: Fix OPAL_CONSOLE_FLUSH prototype and usages
powerpc/mm: fix _PAGE_SWP_SOFT_DIRTY breaking swapoff
powerpc/mm: Fix _PAGE_PTE breaking swapoff
cxl: Enable PCI device ID for future IBM CXL adapter
cxl: use -Werror only with CONFIG_PPC_WERROR
cxl: fix build for GCC 4.6.x
powerpc: Add HWCAP bits for Power9
powerpc/powernv: Reserve PE#0 on NPU
powerpc/powernv: Change NPU PE# assignment
powerpc/powernv: Fix update of NVLink DMA mask
powerpc/powernv: Remove misleading comment in pci.c
powerpc: Implement save_stack_trace_regs() to enable kprobe stack tracing
powerpc: Fix build break due to paca mm_context_t changes
cxl: Fix DSI misses when the context owning task exits
MAINTAINERS: Update Scott Wood's e-mail address
powerpc/powernv: Fix minor off-by-one error in opal_mce_check_early_recovery()
powerpc: Fix style of self-test config prompts
powerpc/powernv: Only delay opal_rtc_read() retry when necessary
...
The recently added OPAL API call, OPAL_CONSOLE_FLUSH, originally took no
parameters and returned nothing. The call was updated to accept the
terminal number to flush, and returned various values depending on the
state of the output buffer.
The prototype has been updated and its usage in the OPAL kmsg dumper has
been modified to support its new behaviour as an incremental flush.
Signed-off-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
