Move to the new style of defining the bus interfaces in separate modules
in order to simplify dependencies.
Signed-off-by: Mark Brown <broonie@linaro.org>
tlv320aic23 chip control interface may work in either I2C or SPI mode
depending on the MODE pin state. Functionality and register layout are
independent of the control mode.
Implement bus-specific parts as separate modules.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds support for the ADAU1977, ADAU1978 and ADAU1979 audio CODEC
devices. They are a family of 4-channel differential input audio ADC devices.
They can be connected to either a SPI or I2C bus. The driver is implemented in
three modules, one main module (adau1977.ko) which implements the device logic
and one module each for SPI (adau1977-spi.ko) and I2C (adau1977-i2c.ko) bus
access.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
There are a few known (minor) problems with having the support code for both I2C
and SPI in the same module:
* We need to be extra careful to make sure to not build the driver into the
kernel if one of the subsystems is build as a module (Currently only I2C
can be build as a module).
* The module init path error handling is rather ugly. E.g. what should be
done if either the SPI or the I2C driver fails to register. Most drivers
that implement SPI and I2C in the same module currently fallback to
undefined behavior in that case. Splitting the the driver into two
modules, one for each bus, allows the registration of the other bus drive
to continue without problems if one of them fails.
This patch splits the ADAV80X driver into 3 modules. One core module that
implements the device logic, but is independent of the bus method used. And one
module for SPI and I2C each that registers the drivers and sets up the regmap
struct for the bus.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
There are a few known (minor) problems with having the support code for both I2C
and SPI in the same module:
* We need to be extra careful to make sure to not build the driver into the
kernel if one of the subsystems is build as a module (Currently only I2C
can be build as a module).
* The module init path error handling is rather ugly. E.g. what should be
done if either the SPI or the I2C driver fails to register? Most drivers
that implement SPI and I2C in the same module currently fallback to
undefined behavior in that case. Splitting the the driver into two
modules, one for each bus, allows the registration of the other bus driver
to continue without problems if one of them fails.
This patch splits the AD193X driver into 3 modules. One core module that
implements the device logic, but is independent of the bus method used. And one
module for SPI and I2C each that registers the drivers and sets up the regmap
struct for the bus.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The PCM512x devices are a family of monolithic CMOS integrated circuits
that include a stereo digital-to-analog converter and additional support
circuitry.
This is an initial driver which supports some core functionality for the
device which covers common use cases but does not cover all features.
Currently only slave clocking modes with automatic clock configuration
are supported and most of the DSP configuration for the device is not
enabled.
Signed-off-by: Mark Brown <broonie@linaro.org>
The wm8997 is a compact, high-performance audio hub CODEC with SLIMbus
interfacing, for smartphones, tablets and other portable audio devices
based on the Arizona platform.
This patch adds the wm8997 CODEC driver.
[Fixed some interface churn from bitrot due to the patch not going via
the MFD tree as expected -- broonie]
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add PCM1792A spi mode codec support. This version implements only
a subset of functionalities. Tested connect to a pandaboard ES
device and based on recently pcm1681 codec.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
PCM1681 can be controlled via I2C, SPI or in bootstrap mode (no control mode). This code add
support only for I2C mode.
Signed-off-by: Marek Belisko <marek.belisko@streamunlimited.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
ak4554 is very simple DA/AD converter which has no setting register.
Note that it has hard coded asymmetric data format
playback : SND_SOC_DAIFMT_RIGHT_J
capture : SND_SOC_DAIFMT_LEFT_J
This driver has single DAI and doesn't have set_fmt.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds the ALC5640 codec driver.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
to support HDMI on CSR SiRFprimaII and atlasVI, we need one more HDMI pseudo
codec, rather than add a new driver, we can make omap HDMI codec common for
other SoCs as well. then the omap-hdmi codec becomes a generic HDMI pseudo-
codec as HDMI audio features depend on HDMI specification not on SoCs.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds a ASoC CODEC driver for the SSM2516. The SSM2516 is a stereo
Class-D audio amplifier with an I2S interface for audio in and a built-in
dynamic range control processor.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
DFBM-CS320 is only one of bluetooth modules using CSR bluetooth chips,
we don't want everyone to have a seperate codec driver. anyway, the
feature of Bluetooth SCO is same on all platforms, so this patch
makes the DFBM-CS320 driver become a common BT SCO link driver.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Transceiver usually means receiver + transmitter. This codec can do only
transmit. Update driver accordingly.
Signed-off-by: Marek Belisko <marek.belisko@streamunlimited.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds a driver for TI's TA5086 6-channel PWM processor.
This chip has a very unusual register layout, specifically because the
registers are of unequal size, and multi-byte registers require bulk
writes to take effect. Regmap does not support these kind of mappings.
Currently, the driver does not touch any of the registers >= 0x20, so
it doesn't matter, because the register map is mapped to an 8-bit array.
In case more features will be added in the future that require access
to higher registers, the entire regmap H/W I/O routines have to be
open-coded.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Adds a driver for Asahi Kasei's AK5386 Single-ended 24-Bit 192kHz
delta-sigma ADC. The device has no control port interface but an
optional RESET/PDN GPIO pin.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for the Dialog DA7213 audio codec.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds the max98090 codec prototype driver.
It supports Headphone only at this point.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Many current Wolfson devices feature DSPs based around an architecture
known as ADSP. Since there is a lot of commonality in the system
integration of these devices a common library will be used to provide
support for them.
This version provides equivalent support for ADSP1 to that currently
included in the WM2200 driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This commit add a sound codec driver for Silicon Laboratories 476x
series of AM/FM radio chips.
Signed-off-by: Andrey Smirnov <andrey.smirnov@convergeddevices.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for Dialog semiconductor's DA9055 audio codec.
This has been tested on DA9055 EVB with Samsung SMDK6410 board.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <david.chen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM0010 is a compact digital signal processor that has been
highly optimised for low-power audio applications. Extensive memory
resources and core optimisation allow the device to manage all audio
processing algorithms efficiently and autonomously, while the host
processor sleeps or performs other tasks.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM5110 is a highly integrated low power audio subsystem for
smartphones, tablets and other portable audio devices. It combines
an advanced DSP feature set with a flexible, high performance audio
hub CODEC.
This patch adds the audio CODEC driver for the device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The STA529 is a digital stereo class-D audio amplifier. It includes an
audio DSP, an ST proprietary high-efficiency class-D driver and CMOS
power output stage. It is intended for high-efficiency
digital-to-power-audio conversion for portable applications.
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Otherwise we fail to link when building as modules due to multiple
init/exit functions.
Reported-by: Fengguang Wu <wfg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds the support for spdif in audio codec.
Signed-off-by: vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM5102 is a highly-integrated low-power audio system for smartphones,
tablets and other portable audio devices based on the Arizona platform.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The Wolfson Arizona series of audio hub CODECs can share a large amount
of their driver code as the result of a common register map. This patch
adds some of this core support, providing a basis for the initial WM5102
audio driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for Dialog DA732x audio codecs.
Signed-off-by: Michal Hajduk <Michal.Hajduk@diasemi.com>
Signed-off-by: Adam Thomson <Adam.Thomson@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add codec-driver for ST-Ericsson AB8500 mixed-signal ASIC.
Signed-off-by: Ola Lilja <ola.o.lilja@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ASoC: Support TI Isabelle Audio driver
The Isabelle Audio IC is a complete low power high fidelity CODEC with integrated
ADCs, DACs, decimation and interpolation filters, PLL, and power providers. This
device supports 2 analog and 2 digital microphone channels, a mono earpiece driver,
stereo class G headphone drivers with ultra low power and best SNR in the industry,
stereo Class D speaker drivers, and 2 high performance Line drivers.
The below patch is a basic driver code for TI Isabelle audio codec. The
functionalities like headset detection, etc., will be included incrementally
in the up-coming patches.
Signed-off-by: Vishwas A Deshpande <vishwas.a.deshpande@ti.com>
Signed-off-by: M R Swami Reddy <mr.swami.reddy@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Introduce codec for HDMI. At the moment, this is a dummy codec. In the
future it will parse the EDID to modify the supported parameters, such
as the number of channels and the sample rates. At the moment, it blindly
supports all the sample rates and audio channels described in the HDMI
1.4a specification.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for Cirrus Logic CS42L52 Low Power Stereo Codec
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Georgi Vlaev <joe@nucleusys.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ML26124-01HB/ML26124-02GD is 16bit monaural audio CODEC which has high
resistance to voltage noise. On chip regulator realizes power supply rejection
ratio be over 90dB so more than 50dB is improved than ever. ML26124-01HB/
ML26124-02GD can deliver stable audio performance without being affected by noise
from the power supply circuit and peripheral components. The chip also includes
a composite video signal output, which can be applied to various portable device
requirements. The ML26124 is realized these functions into very small package
the size is only 2.56mm x 2.46mm therefore can be construct high quality sound
system easily.
ML26124-01HB is 25pin WCSP package; ML26124-02GD is 32pin WQFN package.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add a driver supporting the volume control and the mute pin. Shdn pin
and DAPM are not taken care of yet.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
