Bindings for LP3943 MFD, GPIO and PWM controller are added.
Signed-off-by: Milo Kim <milo.kim@ti.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Atmel PWM controller uses the standard device tree bindings for PWM
controllers.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Update all the Tegra DT bindings to require resets/reset-names properties
where the HW module has reset inputs. Remove any entries from clocks or
clock-names that were only required to identify reset inputs, rather than
referring to real clocks.
This is a DT-ABI-incompatible change. It is the first of two changes
required for me to consider the Tegra DT bindings as stable, the other
being conversion to the common DMA DT bindings.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-By: Terje Bergstrom <tbergstrom@nvidia.com>
Many of the Tegra DT binding documents say nothing about the clocks or
clock-names properties, yet those are present and required in DT files.
This patch simply updates the documentation file to match the implicit
definition of the binding, based on real-world DT content.
All Tegra bindings that mention clocks are updated to have consistent
wording and formatting of the clock-related properties.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-By: Terje Bergstrom <tbergstrom@nvidia.com>
This patch adds device tree support to the PXA's PWM driver. Nothing
needs to be extracted from the device tree node by the PWM device.
Client devices need only specify the period; the per-chip index is
implicitly zero because one device node must be present for each PWM
output in use. This approach is more convenient due to the wide
variability in the number of PWM channels present across the various PXA
variants, and is made possible by the fact that the register sets for
each PWM channel are segregated from each other. An of_xlate() method
is added to parse this single-cell node. The existing ID table is
reused for the match table data.
Tested on a Palm Treo 680 (both platform data and DT cases).
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
patches, both new drivers and fixes to existing. A high percentage of
these are for Samsung platforms like Exynos. Core framework fixes and
some new features like automagical clock re-parenting round out the
patches.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=5GfA
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.12' of git://git.linaro.org/people/mturquette/linux
Pull clock framework changes from Michael Turquette:
"The common clk framework changes for 3.12 are dominated by clock
driver patches, both new drivers and fixes to existing. A high
percentage of these are for Samsung platforms like Exynos. Core
framework fixes and some new features like automagical clock
re-parenting round out the patches"
* tag 'clk-for-linus-3.12' of git://git.linaro.org/people/mturquette/linux: (102 commits)
clk: only call get_parent if there is one
clk: samsung: exynos5250: Simplify registration of PLL rate tables
clk: samsung: exynos4: Register PLL rate tables for Exynos4x12
clk: samsung: exynos4: Register PLL rate tables for Exynos4210
clk: samsung: exynos4: Reorder registration of mout_vpllsrc
clk: samsung: pll: Add support for rate configuration of PLL46xx
clk: samsung: pll: Use new registration method for PLL46xx
clk: samsung: pll: Add support for rate configuration of PLL45xx
clk: samsung: pll: Use new registration method for PLL45xx
clk: samsung: exynos4: Rename exynos4_plls to exynos4x12_plls
clk: samsung: exynos4: Remove checks for DT node
clk: samsung: exynos4: Remove unused static clkdev aliases
clk: samsung: Modify _get_rate() helper to use __clk_lookup()
clk: samsung: exynos4: Use separate aliases for cpufreq related clocks
clocksource: samsung_pwm_timer: Get clock from device tree
ARM: dts: exynos4: Specify PWM clocks in PWM node
pwm: samsung: Update DT bindings documentation to cover clocks
clk: Move symbol export to proper location
clk: fix new_parent dereference before null check
clk: wm831x: Initialise wm831x pointer on init
...
PWM driver consumes at least one and up to three clocks, which need to be
specified in device tree when used. This patch updates bindings
documentation to add information about clocks.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Specify DT bindings for the TPU PWM controller and add OF support to the
driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The PWM client cells format is documented in the generic pwm.txt
documentation and duplicated in all PWM driver bindings. Remove
duplicate information and reference pwm.txt instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Define a PWM_POLARITY_INVERTED macro in include/dt-bindings/pwm/pwm.h to
be used by device tree sources.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Add pwm driver for the NXP pca9685 16 channel pwm-led controller.
The driver is really barebones at this stage. E.g. the OE' pin and
therefore the corresponding registers are not supported.
The driver was tested on a HW where this pin is tied to GND.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
[thierry.reding@gmail.com: style and whitespace cleanups]
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
These continue the multiplatform support for exynos, adding support
for building most of the essential drivers (clocksource, clk, irqchip)
when combined with other platforms. As a result, it should become
really easy to add full multiplatform exynos support in 3.11, although
we don't yet enable it for 3.10.
The changes were not included in the earlier multiplatform series
in order to avoid clashes with the other Exynos updates.
This also includes work from Tomasz Figa to fix the pwm clocksource
code on Exynos, which is not strictly required for multiplatform,
but related to the other patches in this set and needed as a bug
fix for at least one board.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=FY7+
-----END PGP SIGNATURE-----
Merge tag 'multiplatform-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull late ARM Exynos multiplatform changes from Arnd Bergmann:
"These continue the multiplatform support for exynos, adding support
for building most of the essential drivers (clocksource, clk, irqchip)
when combined with other platforms. As a result, it should become
really easy to add full multiplatform exynos support in 3.11, although
we don't yet enable it for 3.10.
The changes were not included in the earlier multiplatform series in
order to avoid clashes with the other Exynos updates.
This also includes work from Tomasz Figa to fix the pwm clocksource
code on Exynos, which is not strictly required for multiplatform, but
related to the other patches in this set and needed as a bug fix for
at least one board."
* tag 'multiplatform-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (22 commits)
ARM: dts: exynops4210: really add universal_c210 dts
ARM: dts: exynos4210: Add basic dts file for universal_c210 board
ARM: dts: exynos4: Add node for PWM device
ARM: SAMSUNG: Do not register legacy timer interrupts on Exynos
clocksource: samsung_pwm_timer: Work around rounding errors in clockevents core
clocksource: samsung_pwm_timer: Correct programming of clock events
clocksource: samsung_pwm_timer: Use proper clockevents max_delta
clocksource: samsung_pwm_timer: Add support for non-DT platforms
clocksource: samsung_pwm_timer: Drop unused samsung_pwm struct
clocksource: samsung_pwm_timer: Keep all driver data in a structure
clocksource: samsung_pwm_timer: Make PWM spinlock global
clocksource: samsung_pwm_timer: Let platforms select the driver
Documentation: Add device tree bindings for Samsung PWM timers
clocksource: add samsung pwm timer driver
irqchip: exynos: look up irq using irq_find_mapping
irqchip: exynos: pass irq_base from platform
irqchip: exynos: localize irq lookup for ATAGS
irqchip: exynos: allocate combiner_data dynamically
irqchip: exynos: pass max combiner number to combiner_init
ARM: exynos: add missing properties for combiner IRQs
...
This patch adds missing documentation describing Device Tree bindings
for Samsung PWM timers.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Update binding document of pwm-tiehrpwm to reflect the usage of similar
modules in da850 and am3xx SOCs.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Update binding document of pwm-tiecap to reflect the usage of similar
modules in da850 and am3xx SOCs.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Add support to set polarity on PWM devices, allowing for inverted
duty cycles.
Also update the binding document to #pwm-cells = <3> to allow
passing the flags from devicetree.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
This patch adds a PWM driver based on Atmel Timer Counter Block. The
Timer Counter Block is used in Waveform generator mode.
A Timer Counter Block provides up to 6 PWM devices grouped by 2:
* group 0 = PWM 0 and 1
* group 1 = PWM 2 and 3
* group 2 = PMW 4 and 5
PWM devices in a given group must be configured with the same period
value. If a PWM device in a group tries to change the period value and
the other device is already configured with a different value an error
will be returned.
This driver requires device tree support. The Timer Counter Block number
used to create a PWM chip is given by the tc-block field in an
"atmel,tcb-pwm" compatible node.
This patch was tested on kizbox board (at91sam9g20 SoC) with pwm-leds.
Signed-off-by: Boris BREZILLON <linux-arm@overkiz.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
The driver supports the following LED outputs as generic PWM driver:
TWL4030 LEDA and LEDB (PWMA and PWMB)
TWL6030 Charging indicator LED (PWM LED)
On TWL6030 when the PWM requested LED is configured to be controlled by SW.
In this case the user can enable/disable and set the duty period freely.
When the PWM has been freed, the LED driver is put back to HW control.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
The driver supports the following PWM outputs:
TWL4030 PWM0 and PWM1
TWL6030 PWM1 and PWM2
On TWL4030 the PWM signals are muxed. Upon requesting the PWM the driver
will select the correct mux so the PWM can be used. When the PWM has been
freed the original configuration is going to be restored.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
This patch
1. Add support for device-tree binding for EHRWPM driver.
2. Set size of pwm-cells set to 3 to support PWM channel number, PWM
period & polarity configuration from device tree.
3. Add enable/disable clock gating in PWM subsystem common config space.
4. When here set .owner member in platform_driver structure to
THIS_MODULE.
Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
This patch
1. Add support for device-tree binding for ECAP APWM driver.
2. Set size of pwm-cells set to 3 to support PWM channel number, PWM
period & polarity configuration from device tree.
3. Add enable/disable clock gating in PWM subsystem common config space.
4. When here set .owner member in platform_driver structure to
THIS_MODULE.
Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
In some platforms (like am33xx), PWM sub modules (ECAP, EHRPWM, EQEP)
are integrated to PWM subsystem. These PWM submodules has resources
shared and only one register bit-field is provided to control
module/clock enable/disable, makes it difficult to handle common
resources from independent PWMSS submodule drivers.
So the solution here implemented in this patch is, to create driver for
PWMSS and take the role of parent driver for PWM submodules. PWMSS
parent driver enumerates all the child nodes under PWMSS module. Also
symbol "pwmss_submodule_state_change" exported to enable clock gating
for individual PWMSS submodules, and submodule drivers has to enable
clock gating from their drivers.
As this is only supported during DT boot, the parent/child relationship
is created and populated in DT execution flow. The only required change
is inside DTS file, making EHRPWM & ECAP as a child to PWMSS node.
Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Add support for encoding PWM properties in bit encoded form with
of_pwm_xlate_with_flags() function support. Platforms require platform
specific PWM properties has to populate in 3rd cell of the pwm-specifier
and PWM driver should also set .of_xlate support with this function.
Currently PWM property polarity encoded in bit position 0 of the third
cell in pwm-specifier.
Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Add support for PWM chips present on SPEAr platforms. These PWM
chips support 4 channel output with programmable duty cycle and
frequency.
More details on these PWM chips can be obtained from relevant
chapter of reference manual, present at following[1] location.
1. http://www.st.com/internet/mcu/product/251211.jsp
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Vipin Kumar <vipin.kumar@st.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
This patch updates pwm-vt8500.c to support devicetree probing and
make use of the common clock subsystem.
A binding document describing the PWM controller found on
arch-vt8500 is also included.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
All legacy PWM providers have now been moved to the PWM subsystem. The
plan for 3.8 is to adapt all board files to provide a lookup table for
PWM devices in order to get rid of the global namespace. Subsequently,
users of the legacy pwm_request() and pwm_free() functions can be
migrated to the new pwm_get() and pwm_put() functions. Once this has
been completed, the legacy API and the compatibility code in the core
can be removed.
In addition to the above, these changes also add support for configuring
the polarity of a PWM signal (currently only supported on ECAP and
EHRPWM) and include a much needed rework of the i.MX driver. Managed
functions to obtain and release a PWM device (devm_pwm_get() and
devm_pwm_put()) have been added and the pwm-backlight driver has been
updated to use them. If the PWM subsystem hasn't been enabled, dummy
functions are provided that allow the subsystem to safely compile out.
Some common checks on input parameters have been moved to the core and
removed from the drivers. Finally, a small fix corrects the description
of the PWM specifier's second cell in the device tree representation.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=MQ5V
-----END PGP SIGNATURE-----
Merge tag 'for-3.7-rc1' of git://gitorious.org/linux-pwm/linux-pwm
Pull pwm changes from Thierry Reding:
"All legacy PWM providers have now been moved to the PWM subsystem.
The plan for 3.8 is to adapt all board files to provide a lookup table
for PWM devices in order to get rid of the global namespace.
Subsequently, users of the legacy pwm_request() and pwm_free()
functions can be migrated to the new pwm_get() and pwm_put()
functions. Once this has been completed, the legacy API and the
compatibility code in the core can be removed.
In addition to the above, these changes also add support for
configuring the polarity of a PWM signal (currently only supported on
ECAP and EHRPWM) and include a much needed rework of the i.MX driver.
Managed functions to obtain and release a PWM device (devm_pwm_get()
and devm_pwm_put()) have been added and the pwm-backlight driver has
been updated to use them. If the PWM subsystem hasn't been enabled,
dummy functions are provided that allow the subsystem to safely
compile out.
Some common checks on input parameters have been moved to the core and
removed from the drivers. Finally, a small fix corrects the
description of the PWM specifier's second cell in the device tree
representation."
* tag 'for-3.7-rc1' of git://gitorious.org/linux-pwm/linux-pwm: (23 commits)
pwm: dt: Fix description of second PWM cell
pwm: Check for negative duty-cycle and period
pwm: Add Ingenic JZ4740 support
MIPS: JZ4740: Export timer API
pwm: Move PUV3 PWM driver to PWM framework
unicore32: pwm: Use managed resource allocations
unicore32: pwm: Remove unnecessary indirection
unicore32: pwm: Use module_platform_driver()
unicore32: pwm: Properly remap memory-mapped registers
pwm-backlight: Use devm_pwm_get() instead of pwm_get()
pwm: Move AB8500 PWM driver to PWM framework
pwm: Fix compilation error when CONFIG_PWM is not defined
pwm: i.MX: fix clock lookup
pwm: i.MX: use per clock unconditionally
pwm: i.MX: add devicetree support
pwm: i.MX: Use module_platform_driver
pwm: i.MX: add functions to enable/disable pwm.
pwm: i.MX: remove unnecessary if in pwm_[en|dis]able
pwm: i.MX: factor out SoC specific functions
pwm: pwm-tiehrpwm: Add support for configuring polarity of PWM
...
The second cell in the PWM specifier denotes the period in nanoseconds,
not the duty cycle. The latter can be freely configured at runtime and
a PWM with a fixed duty cycle would be rather pointless.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: "Benoît Thébaudeau" <benoit.thebaudeau@advansee.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
At the same time remove platform based support. No user for
this driver has made it into mainline so far, so all we break
is out of tree stuff.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
In the reg field we should annotate the register address space in hexadecimal
format.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Encode soc name in the compatible string to know the specific version
hardware block. This is the general approach adopted for most bindings.
Change mxs-pwm binding to use the approach.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Add auxdata to instantiate the PWFM controller from a device tree,
include the corresponding nodes in the dtsi files for Tegra 20 and
Tegra 30 and add binding documentation.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
This patch adds helpers to support device tree bindings for the generic
PWM API. Device tree binding documentation for PWM controllers is also
provided.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
