[Why]
Current periodic interrupt start point calc in optc
is not clear.
[How]
1. DM convert delta time to lines number and dc will calculate the
start position as per lines number and interrupt type.
2. hwss calculates the start point as per line offset.
3. optc programs vertical interrupts register as per start point
and interrupt source.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Certain tests fail after a fresh reboot. This is caused by writing to
registers prior to ungating the stream we're trying to program.
[How]
Make sure the stream is ungated before writing to its registers.
This also enables power-gating plane resources before init_hw
initializes them.
Additionally, this does some refactoring to move gating/ungating
from enable/disable_plane functions to where stream resources are
enabled/disabled.
Signed-off-by: Gary Kattan <gary.kattan@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Pipe related init is possible to optimized if we know what we
intend to program, and if we can determine it matches what is
already programmed for the pipe.
[How]
First step is to isolate the pipe related init code
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
HUBP underflow is never cleared, which causes underflow in one
test to fail another test, violating the independence requirements
[how]
Rather than make clearing implicit, we explicitly clear underflow
status in DTN.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why] On DCN1/DCE, There are two functions programming OCSC:
program_csc_matrix and program_output_csc. They do the same thing.
[How] Consolidate to use only program_output_csc.
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why] We want to increase precision for backlight setting.
But DC interface takes 8 bit backlight level value only.
[How] DMCU already takes 16 bit backlight level.
Expand the DC interface to take 16.16 bit value.
Max 32 bit backlight value (0xFFFF) will represent
max backlight (100%)
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is done to keep things more readable, avoids a true/false flag
in dc interface layer.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is done to clear up the clock programming sequence
since the only time we need to notify pplib is after
clock update.
This also renames the clk block to dccg, at the moment
this block contains both clock management and dccg
functionality.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Logging hardware state can be done by triggering a write to the
debugfs file. It would also be useful to be able to read the hardware
state from the debugfs file to be able to generate a clean log without
timestamps.
[How]
Usage: cat /sys/kernel/debug/dri/0/amdgpu_dm_dtn_log
Threading is an obvious concern when dealing with multiple debugfs
operations and blocking on global state in dm or dc seems unfavorable.
Adding an extra parameter for the debugfs log context state is the
implementation done here. Existing code that made use of DTN_INFO
and its associated macros needed to be refactored to support this.
We don't know the size of the log in advance so it reallocates the
log string dynamically. Once the log has been generated it's copied
into the user supplied buffer for the debugfs. This allows for seeking
support but it's worth nothing that unlike triggering output via
dmesg the hardware state might change in-between reads if your buffer
size is too small.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Jordan Lazare <Jordan.Lazare@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Existing DTN infrastructure in driver is hacky. It uses implicit log
names, and also incorrect escape ID.
[how]
- Implement using generic DTN escape ID.
- Move file logging functionality from driver to to script; driver now outputs to string/buffer
- Move HWSS debug functionality to separate c file
- Add debug functionalty for per-block logging as CSV
- Add pretty print in python
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Cursor boosting is done via CNVC_CUR register which is DPP, not HUBP
Previous commit was implementing it in HUBP functions,
and also breaking diags tests.
[How]
1. Undo original commit as well as Eric's diags test fix, almost completely
2. Move programming to DPP and call via new dc_stream function
3. Also removing cur_rom_en from dpp_cursor_attributes and programming
as part of normal cursor attributes as it depends on cursor color format
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Also rename otg_blank to blank_pixel_data.
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Instead of user set brightness with range of percentage,
HLK test set brightness level with range of normal, this will result in
HLK test case set brightness from 0 to 255, DC set brightness with ramp is 0,
and disabled ramp change which will fail the HLK test.
Fix:
In case of unblank stream and turn on edp, change brightness level in
stream to 0xFFFFFFFF(actural maximum level is 0xFF), use that value as
a flag to recogonize this the case of resume from S3.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move cursor programming to inside the OTG_MASTER_UPDATE_LOCK
If graphics plane go from 1 pipe to hsplit, the cursor updates
after mpc programming and unlock. Which means there is a window
of time where cursor is enabled on the wrong pipe if it's on
the right side of the screen (i.e. case where cursor need to
move from pipe 0 to pipe 3 post split). This will cause pstate hang.
Solution is to program the cursor while still locked.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Proper sequence should be:
disable backlight
dp blank
disable output
edp power off
In enable accelatate mode, all the encoder and controller
are disabled, so move disable eDP to the function is the
easiest way to implement.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Also rename timing_generator to optc
Signed-off-by: Yue Hin Lau <Yuehin.Lau@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Jordan Lazare <Jordan.Lazare@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It may take over 200ms for wait hpd ready. To optimize the resume time,
we can power on eDP in init_hw, wait for hpd ready when doing link
training.
also create separate eDP enable function to make sure eDP is powered up
before doing and DPCD access, as HPD low will result in DPDC transaction
failure.
After optimization,
setpowerstate 145ms -> 9.8ms,
DPMS 387ms -> 18.9ms
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Work around for a hw bug causing optc underflow if blank data
double buffer disable and remove mpcc.
Checking optc status after otg unlock, after wait mpcc idle
check status again, if optc underflow just happens after wait
mpcc idle, clear underflow status and enable blank data double
buffer.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Power on one plane after disable all the planes, for
a hw bug work around to resolve stutter efficiency issue.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
SMU can future lower voltages in long idle case when all display is off.
If all display output is turned off via DPMS, send display_count = 0
after all output are turned off.
otherwise send display_count msg before turning on display to make sure
SMU exit S0i2 state. before is not neccessary as we are out of S0i2
when driver execute code, but send message before anyways for correctness.
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are different code to disable front end, it is
difficult to debug and adding new process.
This refactor makes all disable front end call the same
functions.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dc_link is at a higher level than link_encoder, and we only want
higher-level components to be able to access lower-level ones,
not the other way around.
Signed-off-by: Andrew Jiang <Andrew.Jiang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This feature synchronizes multiple displays with various timings
to a display with the highest refresh rate
it is enabled if edid caps flag multi_display_sync is set to one
There are limitations on refresh rates allowed
that can be synchronized. That would
prevent from underflow and other potential
corruptions.
Multi display synchronization is using the
same functions as timing_sync in order to minimize
redunduncy and decision to disable synchronization is
based on trigger parametre set in DM
Feature is developed for DCN1 and DCE11
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A recent commit moved the backlight control code along with the register
defines, but did not move the power control code. This along with
remnant fields in the dce110_link_enc_registers struct made it so that
the code still compiled, but any attempts to access the
LVTMA_PWRSEQ_STATE register led to reading from an address of 0. This
patch corrects that.
Also, rename blacklight_control to edp_backlight_control (Typo fix).
Signed-off-by: Andrew Jiang <Andrew.Jiang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Yue Hin Lau <Yuehin.Lau@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Rename all the dc validate_context to dc_state and
dc current_context to current_state.
Signed-off-by: Jerry Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-Flattening core_dc to dc
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Zeyu Fan <Zeyu.Fan@amd.com>
Reviewed-by: Zeyu Fan <Zeyu.Fan@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
