commit e00c27ef3b
(ARM: dts: OMAP5: Add Palmas MFD node and regulator nodes)
introduced regulator entries for OMAP5uEVM.
However, The regulator information is based on an older temporary
pre-production board variant and does not reflect production board
750-2628-XXX boards.
The following fixes are hence mandatory to ensure right voltage is
supplied to key OMAP5 SoC voltage rails:
- LDO1 supplies VDDAPHY_CAM which is OMAP5's vdda_csiporta/b/c. This
can only be supplied at 1.5V or 1.8V and we currently supply 2.8V.
To prevent any potential device damage risk, use the specified
1.5V-1.8V supply.
Remove 'always-on' and 'boot-on' settings here as it is
a 'on need' supply to SoC IP and is not enabled by PMIC by
default at boot.
- LDO3 supplies Low Latency Interface(LLI) hardware module which is a
special hardware to communicate with Modem. However since uEVM is
not setup by default for this communication, this should be disabled
by default.
Further, vdda_lli is supposed to be 1.5V and not 3V.
- LDO4 supplies VDDAPHY_DISP which is vdda_dsiporta/c/vdda_hdmi
This can only be supplied at 1.5V or 1.8V and we currently
supply 2.2V.
To prevent any potential device damage risk, use the specified
1.5V-1.8V supply.
Remove 'always-on' and 'boot-on' settings here as it is a 'on need'
supply to SoC IP and is not enabled by PMIC by default at boot.
- LDO6 supplies the board specified VDDS_1V2_WKUP supply going to
ldo_emu_wkup/vdds_hsic. To stay within the SoC specification supply
1.2V instead of 1.5V.
- LDO7 supplies VDD_VPP which is vpp1. This is currently configured for
1.5V which as per data manual "A pulse width of 1000 ns and an amplitude
of 2V is required to program each eFuse bit. Otherwise, VPP1 must not
be supplied".
So, fix the voltage to 2V. and disable the supply since we have no plans
of programming efuse bits - it can only be done once - in factory.
Further it is not enabled by default by PMIC so, 'boot-on' must be
removed, and the 'always-on' needs to be removed to achieve pulsing
if efuse needs to be programmed.
- LDO9 supplies the board specified vdds_sdcard supply going within SoC
specification of 1.8V or 3.0V. Further the supply is controlled by
switch enabled by REGEN3. So, introduce REGEN3 and map sdcard slot to
be powered by LDO9. Remove 'always-on' allowing the LDO to be disabled
on need basis.
Reported-by: Marc Jüttner <m-juettner@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: J Keerthy <j-keerthy@ti.com>
Acked-by: Benoit Cousson <benoit.cousson@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
commit e00c27ef3b
(ARM: dts: OMAP5: Add Palmas MFD node and regulator nodes)
introduced regulator entries for OMAP5uEVM.
However, currently we use the Palmas regulator names which is used for
different purposes on uEVM. Document the same based on 750-2628-XXX
boards - which is meant to be supported by this dts.
Reported-by: Marc Jüttner <m-juettner@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: J Keerthy <j-keerthy@ti.com>
Acked-by: Benoit Cousson <benoit.cousson@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In commit 33d7885b59
x86/mce: Update MCE severity condition check
We simplified the rules to recognise each classification of recoverable
machine check combining the instruction and data fetch rules into a
single entry based on clarifications in the June 2013 SDM that all
recoverable events would be reported on the unaffected processor with
MCG_STATUS.EIPV=0 and MCG_STATUS.RIPV=1. Unfortunately the simplified
rule has a couple of bugs. Fix them here.
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix the test within handle_pfmf() if the host has the NQ key-setting
facility installed.
Right now the code would incorrectly generate a program check in the
guest if the NQ control bit for a pfmf request was set and if the host
has the NQ key-setting facility installed.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Any uaccess between guest_enter and guest_exit could trigger a page fault,
the page fault handler would handle it as a guest fault and translate a
user address as guest address.
Signed-off-by: Dominik Dingel <dingel@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
CC: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- Driver fixes for AM33xx, SIRF and PFC pin controllers.
- Fix a compile warning from the pinctrl single-register
driver.
- Fix a little nasty memory leak.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=URtB
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-v3.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
- Driver fixes for AM33xx, SIRF and PFC pin controllers
- Fix a compile warning from the pinctrl single-register driver
- Fix a little nasty memory leak
* tag 'pinctrl-for-v3.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: fix a memleak when freeing maps
pinctrl: pinctrl-single: fix compile warning when no CONFIG_PM
pinctrl: sh-pfc: fix SDHI0 VccQ regulator on sh73a0 with DT
arm/dts: sirf: fix the pingroup name mismatch between drivers and dts
pinctrl: sirf: add usp0_uart_nostreamctrl pin group for usp-uart without flowctrl
pinctrl: sirf: fix the pin number and mux bit for usp0
pinctrl: am33xx dt binding: correct include path
So, there's a comment I put at the top of this, which people seem to
fail to read. So let's fix it for them instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Msm gpiomux can be used only for 7x30 and 8x50.
Prevent compilation and fix build issues on 7X00, 8X60 and 8960.
Signed-off-by: Rohit Vaswani <rvaswani@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
This is a largeish batch of fixes, mostly because I missed -rc2 due to
travel/vacation. So in number these are a bit more than ideal unless
you amortize them over two -rcs.
Quick breakdown:
- Defconfig updates
- Making multi_v7_defconfig useful on more hardware to encourage
single-image usage
- Davinci and nomadik updates due to new code merged this merge window
- Fixes for UART on Samsung platforms, both PM and clock-related
- A handful of warning fixes from defconfig builds, including for
max8925 backlight and pxamci (both with appropriate acks)
- Exynos5440 fixes for LPAE configuration, PM
- ...plus a bunch of other smaller changes all over the place
I expect to switch to regressions-or-severe-bugs-only fixes from here
on out.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=XOG3
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"This is a largeish batch of fixes, mostly because I missed -rc2 due to
travel/vacation. So in number these are a bit more than ideal unless
you amortize them over two -rcs.
Quick breakdown:
- Defconfig updates
- Making multi_v7_defconfig useful on more hardware to encourage
single-image usage
- Davinci and nomadik updates due to new code merged this merge
window
- Fixes for UART on Samsung platforms, both PM and clock-related
- A handful of warning fixes from defconfig builds, including for
max8925 backlight and pxamci (both with appropriate acks)
- Exynos5440 fixes for LPAE configuration, PM
- ...plus a bunch of other smaller changes all over the place
I expect to switch to regressions-or-severe-bugs-only fixes from here
on out"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (37 commits)
mfd: max8925: fix dt code for backlight
ARM: omap5: Only select errata 798181 if SMP
ARM: EXYNOS: Update CONFIG_ARCH_NR_GPIO for Exynos
ARM: EXYNOS: Fix low level debug support
ARM: SAMSUNG: Save/restore only selected uart's registers
ARM: SAMSUNG: Add SAMSUNG_PM config option to select pm
ARM: S3C24XX: Add missing clkdev entries for s3c2440 UART
ARM: multi_v7_defconfig: Select USB chipidea driver
ARM: pxa: propagate errors from regulator_enable() to pxamci
ARM: zynq: fix compilation warning
ARM: keystone: fix compilation warning
ARM: highbank: Only touch common coherency control register fields
ARM: footbridge: fix overlapping PCI mappings
dmaengine: shdma: fix a build failure on platforms with no DMA support
ARM: STi: Set correct ARM ERRATAs.
ARM: dts: STi: Fix pinconf setup for STiH416 serial2
ARM: nomadik: configure for NO_HZ and HRTIMERS
ARM: nomadik: update defconfig base
ARM: nomadik: Update MMC defconfigs
ARM: davinci: defconfig: enable EDMA driver
...
GCC will optimize mxcsr_feature_mask_init in arch/x86/kernel/i387.c:
memset(&fx_scratch, 0, sizeof(struct i387_fxsave_struct));
asm volatile("fxsave %0" : : "m" (fx_scratch));
mask = fx_scratch.mxcsr_mask;
if (mask == 0)
mask = 0x0000ffbf;
to
memset(&fx_scratch, 0, sizeof(struct i387_fxsave_struct));
asm volatile("fxsave %0" : : "m" (fx_scratch));
mask = 0x0000ffbf;
since asm statement doesn’t say it will update fx_scratch. As the
result, the DAZ bit will be cleared. This patch fixes it. This bug
dates back to at least kernel 2.6.12.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@vger.kernel.org>
Written by Catalin Marinas, tested by APM on storm platform. This is needed
because of the failures encountered when running SpecWeb benchmark test.
Signed-off-by: Feng Kan <fkan@apm.com>
Acked-by: Kumar Sankaran <ksankaran@apm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The perf_event code references sie_exit even if KVM is not available.
So add proper ifdefs to fix this one:
arch/s390/built-in.o: In function `sys_call_table_emu':
(.rodata+0x2b98): undefined reference to `sie_exit'
arch/s390/built-in.o: In function `sys_call_table_emu':
(.rodata+0x2ba0): undefined reference to `sie_exit'
make: *** [vmlinux] Error 1
Reported-by: Zhouping Liu <zliu@redhat.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The find_next_bit_left function is broken if used with an offset which
is not a multiple of 64. The shift to mask the bits of a 64-bit word
not to search is in the wrong direction, the result can be either a
bit found smaller than the offset or failure to find a set bit.
Cc: <stable@vger.kernel.org> # v3.8+
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Just add the new model number where appropiate.
Cc: stable@vger.kernel.org # v3.10
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
'VIRTIO_CONSOLE' depends on 'TTY', so need to select 'TTY' explicitly
before selecting 'VIRTIO_CONSOLE'.
Otherwise randconfig can generate a config file which enables
'VIRTIO_CONSOLE' but has 'TTY' disabled.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
a.out support on ARM requires that argc, argv and envp are passed in
r0-r2 respectively, which requires hacking load_aout_binary to
prevent argc being clobbered by the return code. Whilst mainline kernels
do set the registers up in start_thread, the aout loader has never
carried the hack in mainline.
Initialising the registers in this way actually goes against the libc
expectations for ELF binaries, where argc, argv and envp are passed on
the stack, with r0 being used to hold a pointer to an exit function for
cleaning up after the dynamic linker if required. If the pointer is
NULL, then it is ignored. When execing an ELF binary, Linux currently
zeroes r0, then sets it to argc and then finally clobbers it with the
return value of the execve syscall, so we actually end up with:
r0 = 0
stack[0] = argc
r1 = stack[1] = argv
r2 = stack[2] = envp
libc treats r1 and r2 as undefined. The clobbering of r0 by sys_execve
works for user-spawned threads, but when executing an ELF binary from a
kernel thread (via call_usermodehelper), the execve is performed on the
ret_from_fork path, which restores r0 from the saved pt_regs, resulting
in argc being presented to the C library. This has horrible consequences
when the application exits, since we have an exit function registered
using argc, resulting in a jump to hyperspace.
This patch solves the problem by removing the partial a.out support from
arch/arm/ altogether.
Cc: <stable@vger.kernel.org>
Cc: Ashish Sangwan <ashishsangwan2@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As of commit b9d4d42ad9 (ARM: Remove __ARCH_WANT_INTERRUPTS_ON_CTXSW on
pre-ARMv6 CPUs), the mm switching on VIVT processors is done in the
finish_arch_post_lock_switch() function to avoid whole cache flushing
with interrupts disabled. The need for deferred mm switch is stored as a
thread flag (TIF_SWITCH_MM). However, with preemption enabled, we can
have another thread switch before finish_arch_post_lock_switch(). If the
new thread has the same mm as the previous 'next' thread, the scheduler
will not call switch_mm() and the TIF_SWITCH_MM flag won't be set for
the new thread.
This patch moves the switch pending flag to the mm_context_t structure
since this is specific to the mm rather than thread.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: <stable@vger.kernel.org> # 3.5+
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 93dc688 (ARM: 7684/1: errata: Workaround for Cortex-A15 erratum 798181 (TLBI/DSB operations)) causes the following undefined instruction error on a mx53 (Cortex-A8):
Internal error: Oops - undefined instruction: 0 [#1] SMP ARM
CPU: 0 PID: 275 Comm: modprobe Not tainted 3.11.0-rc2-next-20130722-00009-g9b0f371 #881
task: df46cc00 ti: df48e000 task.ti: df48e000
PC is at check_and_switch_context+0x17c/0x4d0
LR is at check_and_switch_context+0xdc/0x4d0
This problem happens because check_and_switch_context() calls dummy_flush_tlb_a15_erratum() without checking if we are really running on a Cortex-A15 or not.
To avoid this issue, only call dummy_flush_tlb_a15_erratum() inside
check_and_switch_context() if erratum_a15_798181() returns true, which means that we are really running on a Cortex-A15.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Secondary CPUs write to __boot_cpu_mode with caches disabled, and thus a
cached value of __boot_cpu_mode may be incoherent with that in memory.
This could lead to a failure to detect mismatched boot modes.
This patch adds flushing to ensure that writes by secondaries to
__boot_cpu_mode are made visible before we test against it.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <cdall@cs.columbia.edu>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert CONFIG_HOTPLUG_PCI from tristate to bool. This only affects
the hotplug core; several of the hotplug drivers can still be modules.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
89ae7b5bbd
(ARM: shmobile: armadillo800eva: Register pinctrl mapping for INTC)
mistakenly requests GPIO 166 in board code,
most probably due to a wrong merge conflict resolution.
As the GPIO is passed to the st1232 driver through platform
data and requested by the driver,
there's no need to request it in board code. Fix it.
Tested by: Cao Minh Hiep <cm-hiep@jinso.co.jp>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
- fix kernel booting on exynos5440
skip pm which is not supported
update regarding LPAE features
- fix s3c2440 uart with adding clkdev entries
- fix compilatioin for Samsung SoCs with selecting pm
- update ARCH_NR_GPIO to support exynos4412 has more gpios
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ygWA
-----END PGP SIGNATURE-----
Merge tag 'samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
From Kukjin Kim:
Samsung fixes for v3.11
- fix kernel booting on exynos5440
skip pm which is not supported
update regarding LPAE features
- fix s3c2440 uart with adding clkdev entries
- fix compilatioin for Samsung SoCs with selecting pm
- update ARCH_NR_GPIO to support exynos4412 has more gpios
* tag 'samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Update CONFIG_ARCH_NR_GPIO for Exynos
ARM: EXYNOS: Fix low level debug support
ARM: SAMSUNG: Save/restore only selected uart's registers
ARM: SAMSUNG: Add SAMSUNG_PM config option to select pm
ARM: S3C24XX: Add missing clkdev entries for s3c2440 UART
ARM: EXYNOS: Enable 64-bit DMA for EXYNOS5440 if LPAE is enabled
ARM: EXYNOS: change the PHYSMEM_BITS and SECTION_SIZE
ARM: EXYNOS: skip pm support on exynos5440
Signed-off-by: Olof Johansson <olof@lixom.net>
Avoids the following warning when SMP is off:
warning: (ARCH_KEYSTONE && SOC_OMAP5) selects ARM_ERRATA_798181 which
has unmet direct dependencies (CPU_V7 && SMP)
Reported-by: Emilio López <emilio@elopez.com.ar>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull powerpc fixes from Ben Herrenschmidt:
"Here is a series of powerpc fixes. It's a bit big, mostly because of
the series of 11 "EEH" patches from Gavin. The EEH (Our IBM specific
PCI/PCIe Enhanced Error Handling) code had been rotting for a while
and this merge window saw a significant rework & fixing of it by Gavin
Shan.
However, that wasn't complete and left some open issues. There were
still a few corner cases that didn't work properly, for example in
relation to hotplug and devices without explicit error handlers. We
had some patches but they weren't quite good enough yet so I left them
off the 3.11 merge window.
Gavin since then fixed it all up, we ran quite a few rounds of testing
and it seems fairly solid (at least probably more than it has ever
been). This should probably have made -rc1 but both Gavin and I took
some vacation so it had to wait for -rc2.
The rest is more bug fixes, mostly to new features recently added, for
example, we missed the cpu table entry for one of the two models of P8
(we didn't realize they had different PVR [Processor Version Register]
values), some module CRC issues, etc..."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (23 commits)
powerpc/perf: BHRB filter configuration should follow the task
powerpc/perf: Ignore separate BHRB privilege state filter request
powerpc/powernv: Mark pnv_pci_init_ioda2_phb() as __init
powerpc/mm: Use the correct SLB(LLP) encoding in tlbie instruction
powerpc/mm: Fix fallthrough bug in hpte_decode
powerpc/pseries: Fix a typo in pSeries_lpar_hpte_insert()
powerpc/eeh: Introdce flag to protect sysfs
powerpc/eeh: Fix unbalanced enable for IRQ
powerpc/eeh: Don't use pci_dev during BAR restore
powerpc/eeh: Use partial hotplug for EEH unaware drivers
powerpc/pci: Partial tree hotplug support
powerpc/eeh: Use safe list traversal when walking EEH devices
powerpc/eeh: Keep PE during hotplug
powerpc/pci/hotplug: Don't need to remove from EEH cache twice
powerpc/pci: Override pcibios_release_device()
powerpc/eeh: Export functions for hotplug
powerpc/eeh: Remove reference to PCI device
powerpc: Fix the corrupt r3 error during MCE handling.
powerpc/perf: Set PPC_FEATURE2_EBB when we register the power8 PMU
powerpc/pseries: Drop "select HOTPLUG"
...
Pull crypto fixes from Herbert Xu:
"This push fixes a memory corruption issue in caam, as well as
reverting the new optimised crct10dif implementation as it breaks boot
on initrd systems.
Hopefully crct10dif will be reinstated once the supporting code is
added so that it doesn't break boot"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
Revert "crypto: crct10dif - Wrap crc_t10dif function all to use crypto transform framework"
crypto: caam - Fixed the memory out of bound overwrite issue
With the recent cleanup in Exynos platform code notably commits
17859bec ("ARM: EXYNOS: Do not select legacy Kconfig symbols any
more") and b9222210 ("ARM: EXYNOS: Remove mach/gpio.h"), the definition
of ARCH_NR_GPIOS got removed. This started causing problems on SoCs like
Exynos4412 which have more than the default number of GPIOs. Thus define
this number in KConfig file which takes care of current SoC requirements
and provides scope for GPIO expanders. Without this patch we get the
following errors during boot:
gpiochip_add: gpios 251..258 (gpv0) failed to register
samsung-pinctrl 106e0000.pinctrl: failed to register gpio_chip gpv0, error code: -22
samsung-pinctrl: probe of 106e0000.pinctrl failed with error -22
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Presently, using exynos_defconfig with CONFIG_DEBUG_LL and CONFIG_EARLY_PRIN
on, kernel is not booting, we are getting following:
[ 0.000000] ------------[ cut here ]------------
[ 0.000000] kernel BUG at mm/vmalloc.c:1134!
[ 0.000000] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM
[ 0.000000] Modules linked in:
[ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 3.11.0-rc1 #633
[ 0.000000] task: c052ec48 ti: c0524000 task.ti: c0524000
[ 0.000000] PC is at vm_area_add_early+0x54/0x94
[ 0.000000] LR is at add_static_vm_early+0xc/0x60
Its because exynos[4/5]_map_io() function ioremaps a single 512KB memory
size for all the four uart ports which envelopes the mapping created by
debug_ll_io_init(), called earlier in exynos_init_io().
This patch removes iodesc entries for UART controller for all Samsung SoC's,
since now the Samsung uart driver does a ioremap during probe and any needed
iomapping for earlyprintk will be handled by debug_ll_io_init().
Tested on smdk4412 and smdk5250.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Basically this code gets executed only during debugging i.e when
DEBUG_LL & SAMSUNG_PM_DEBUG is on, so required only for UART used
for debugging. Since we are removing static iodesc entries for UARTs,
so now only the selected (CONFIG_DEBUG_S3C_UART) UART will be
ioremapped by the debug_ll_io_init() for DEBUG_LL, so save/restore
uart registers only for selected uart.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This reverts commits
67822649d739761214ee0b95a7f85731d939625a2d31e518a4
Unfortunately this change broke boot on some systems that used an
initrd which does not include the newly created crct10dif modules.
As these modules are required by sd_mod under certain configurations
this is a serious problem.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch enables the selection of samsung pm related stuffs
when SAMSUNG_PM config is enabled and not just when generic PM
config is enabled. Power management for s3c64XX and s3c24XX
is enabled by default and for other platform depends on S5P_PM.
This patch also fixes the following compilation error's when compiling
a platform like exynos5440 which does not select pm stuffs.
arch/arm/mach-exynos/built-in.o: In function '__virt_to_phys':
linux/arch/arm/include/asm/memory.h:175: undefined reference to 's3c_cpu_resume'
linux/arch/arm/include/asm/memory.h:175: undefined reference to 's3c_cpu_resume'
linux/arch/arm/include/asm/memory.h:175: undefined reference to 's3c_cpu_resume'
linux/arch/arm/include/asm/memory.h:175: undefined reference to 's3c_cpu_resume'
arch/arm/mach-exynos/built-in.o: In function 'exynos5_init_irq':
linux/arch/arm/mach-exynos/common.c:492: undefined reference to 's3c_irq_wake'
linux/arch/arm/mach-exynos/common.c:492: undefined reference to 's3c_irq_wake'
arch/arm/mach-exynos/built-in.o: In function 'exynos4_init_irq':
linux/arch/arm/mach-exynos/common.c:476: undefined reference to 's3c_irq_wake'
linux/arch/arm/mach-exynos/common.c:476: undefined reference to 's3c_irq_wake'
arch/arm/plat-samsung/built-in.o: In function 's3c_irqext_wake':
linux/arch/arm/plat-samsung/pm.c:144: undefined reference to 's3c_irqwake_eintallow'
linux/arch/arm/plat-samsung/pm.c:144: undefined reference to 's3c_irqwake_eintallow'
arch/arm/plat-samsung/built-in.o: In function 's3c_pm_enter':
linux/arch/arm/plat-samsung/pm.c:263: undefined reference to 's3c_irqwake_intallow'
linux/arch/arm/plat-samsung/pm.c:263: undefined reference to 's3c_irqwake_intallow'
linux/arch/arm/plat-samsung/pm.c:264: undefined reference to 's3c_irqwake_eintallow'
linux/arch/arm/plat-samsung/pm.c:264: undefined reference to 's3c_irqwake_eintallow'
linux/arch/arm/plat-samsung/pm.c:275: undefined reference to 's3c_pm_save_core'
linux/arch/arm/plat-samsung/pm.c:279: undefined reference to 's3c_pm_configure_extint'
linux/arch/arm/plat-samsung/pm.c:310: undefined reference to 's3c_pm_restore_core'
make: *** [vmlinux] Error 1
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
When the task moves around the system, the corresponding cpuhw
per cpu strcuture should be popullated with the BHRB filter
request value so that PMU could be configured appropriately with
that during the next call into power_pmu_enable().
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Completely ignore BHRB privilege state filter request as we are
already configuring that with privilege state filtering attribute
for the accompanying PMU event. This would help achieve cleaner
user space interaction for BHRB.
This patch fixes a situation like this
Before patch:-
------------
./perf record -j any -e branch-misses:k ls
Error:
The sys_perf_event_open() syscall returned with 95 (Operation not
supported) for event (branch-misses:k).
/bin/dmesg may provide additional information.
No CONFIG_PERF_EVENTS=y kernel support configured?
Here 'perf record' actually copies over ':k' filter request into BHRB
privilege state filter config and our previous check in kernel would
fail that.
After patch:-
-------------
./perf record -j any -e branch-misses:k ls
perf perf.data perf.data.old test-mmap-ring
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.002 MB perf.data (~102 samples)]
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Mark pnv_pci_init_ioda2_phb() as __init. It is called only from an
init function (pnv_pci_init()), and it calls an init function
(pnv_pci_init_ioda_phb()):
pnv_pci_init # init
pnv_pci_init_ioda2_phb # non-init
pnv_pci_init_ioda_phb # init
This should fix a section mismatch warning.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The sllp value is stored in mmu_psize_defs in such a way that we can easily OR
the value to get the operand for slbmte instruction. ie, the L and LP bits are
not contiguous. Decode the bits and use them correctly in tlbie.
regression is introduced by 1f6aaaccb1
"powerpc: Update tlbie/tlbiel as per ISA doc"
Reported-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We should not fallthrough different case statements in hpte_decode. Add
break statement to break out of the switch. The regression is introduced by
dcda287a9b "powerpc/mm: Simplify hpte_decode"
Reported-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 801eb73f45 introduced
a bug while checking PTE flags. We have to drop the _PAGE_COHERENT flag
when __PAGE_NO_CACHE is set and the cache update policy is not write-through
(i.e. _PAGE_WRITETHRU is not set)
Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
CC: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch restores serial port operation which has been broken since
commit 60e9357547 ("serial: samsung: enable clock before clearing
pending interrupts during init")
That commit only uncovered the real issue which was missing clkdev
entries for the "uart" clocks on S3C2440. It went unnoticed so far
because return value of clk API calls were not being checked at all
in the samsung serial port driver.
This patch should be backported to at least 3.10 stable kernel, since
the serial port has not been working on s3c2440 since 3.10-rc5.
Cc: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
[on S3C2440 SoC based Mini2440 board]
Tested-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Tested-by: Juergen Beisert <jbe@pengutronix.de>
Cc: <stable@vger.kernel.org> [3.10]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The patch introduces flag EEH_DEV_SYSFS to keep track that the sysfs
entries for the corresponding EEH device (then PCI device) has been
added or removed, in order to avoid race condition.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
While restoring BARs for one specific PCI device, the pci_dev
instance should have been released. So it's not reliable to use
the pci_dev instance on restoring BARs. However, we still need
some information (e.g. PCIe capability position, header type) from
the pci_dev instance. So we have to store those information to
EEH device in advance.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When EEH error happens to one specific PE, some devices with drivers
supporting EEH won't except hotplug on the device. However, there
might have other deivces without driver, or with driver without EEH
support. For the case, we need do partial hotplug in order to make
sure that the PE becomes absolutely quite during reset. Otherise,
the PE reset might fail and leads to failure of error recovery.
The current code doesn't handle that 'mixed' case properly, it either
uses the error callbacks to the drivers, or tries hotplug, but doesn't
handle a PE (EEH domain) composed of a combination of the two.
The patch intends to support so-called "partial" hotplug for EEH:
Before we do reset, we stop and remove those PCI devices without
EEH sensitive driver. The corresponding EEH devices are not detached
from its PE, but with special flag. After the reset is done, those
EEH devices with the special flag will be scanned one by one.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When EEH error happens to one specific PE, the device drivers
of its attached EEH devices (PCI devices) are checked to see
the further action: reset with complete hotplug, or reset without
hotplug. However, that's not enough for those PCI devices whose
drivers can't support EEH, or those PCI devices without driver.
So we need do so-called "partial hotplug" on basis of PCI devices.
In the situation, part of PCI devices of the specific PE are
unplugged and plugged again after PE reset.
The patch changes pcibios_add_pci_devices() so that it can support
full hotplug and so-called "partial" hotplug based on device-tree
or real hardware. It's notable that pci_of_scan.c has been changed
for a bit in order to support the "partial" hotplug based on dev-tree.
Most of the generic code already supports that, we just need to
plumb it properly on our side.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, we're trasversing the EEH devices list using list_for_each_entry().
That's not safe enough because the EEH devices might be removed from
its parent PE while doing iteration. The patch replaces that with
list_for_each_entry_safe().
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When we do normal hotplug, the PE (shadow EEH structure) shouldn't be
kept around.
However, we need to keep it if the hotplug an artifial one caused by
EEH errors recovery.
Since we remove EEH device through the PCI hook pcibios_release_device(),
the flag "purge_pe" passed to various functions is meaningless. So the patch
removes the meaningless flag and introduce new flag "EEH_PE_KEEP"
to save the PE while doing hotplug during EEH error recovery.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Make some functions public in order to support hotplug on either specific
PCI bus or PCI device in future.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We will rely on pcibios_release_device() to remove the EEH cache
and unbind EEH device for the specific PCI device. So we shouldn't
hold the reference to the PCI device from EEH cache and EEH device.
Otherwise, pcibios_release_device() won't be called as we expected.
The patch removes the reference to the PCI device in EEH core.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
During Machine Check interrupt on pseries platform, R3 generally points to
memory region inside RTAS (FWNMI) area. We see r3 corruption because when RTAS
delivers the machine check exception it passes the address inside FWNMI area
with the top most bit set. This patch fixes this issue by masking top two bit
in machine check exception handler.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The presence or absence of EBB is advertised to userspace via the presence
or absence of PPC_FEATURE2_EBB in cpu_user_features2.
Because the kernel can be built without PMU support, we should only add
PPC_FEATURE2_EBB to cpu_user_features2 when we successfully register the
power8 PMU support.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The Kconfig symbol HOTPLUG was removed with commit 40b313608a ("Finally
eradicate CONFIG_HOTPLUG"). But there's still one select statement for
that symbol. It seems that select statement was added after the patch to
remove CONFIG_HOTPLUG was submitted. Anyhow, it is useless and can be
dropped.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In hard_irq_disable(), we accessed the PACA before we hard disabled
the interrupts, potentially causing a warning as get_paca() will
us debug_smp_processor_id().
Move that to after the disabling, and also use local_paca directly
rather than get_paca() to avoid several redundant and useless checks.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Module CRCs are implemented as absolute symbols that get resolved by
a linker script. We build an intermediate .o that contains an
unresolved symbol for each CRC. genksysms parses this .o, calculates
the CRCs and writes a linker script that "resolves" the symbols to
the calculated CRC.
Unfortunately the ppc64 relocatable kernel sees these CRCs as symbols
that need relocating and relocates them at boot. Commit d4703aef
(module: handle ppc64 relocating kcrctabs when CONFIG_RELOCATABLE=y)
added a hook to reverse the bogus relocations. Part of this patch
created a symbol at 0x0:
# head -2 /proc/kallsyms
0000000000000000 T reloc_start
c000000000000000 T .__start
This reloc_start symbol is causing lots of confusion to perf. It
thinks reloc_start is a massive function that stretches from 0x0 to
0xc000000000000000 and we get various cryptic errors out of perf,
including:
problem incrementing symbol count, skipping event
This patch removes the reloc_start linker script label and instead
defines it as PHYSICAL_START. We also need to wrap it with
CONFIG_PPC64 because the ppc32 kernel can set a non zero
PHYSICAL_START at compile time and we wouldn't want to subtract
it from the CRCs in that case.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
POWER8 comes with two different PVRs. This patch enables the additional
PVR in the cputable.
The existing entry (PVR=0x4b) is renamed to POWER8E and the new entry
(PVR=0x4d) is given POWER8.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pull alpha architecture fixes from Matt Turner:
"This contains mostly clean ups and fixes but also an implementation of
atomic64_dec_if_positive() and a pair of new syscalls"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha:
alpha: Use handle_percpu_irq for the timer interrupt
alpha: Force the user-visible HZ to a constant 1024.
alpha: Don't if-out dp264_device_interrupt.
alpha: Use __builtin_alpha_rpcc
alpha: Fix type compatibility warning for marvel_map_irq
alpha: Generate dwarf2 unwind info for various kernel entry points.
alpha: Implement atomic64_dec_if_positive
alpha: Improve atomic_add_unless
alpha: Modernize lib/mpi/longlong.h
alpha: Add kcmp and finit_module syscalls
alpha: locks: remove unused arch_*_relax operations
alpha: kernel: typo issue, using '1' instead of '11'
alpha: kernel: using memcpy() instead of strcpy()
alpha: Convert print_symbol to %pSR
CONFIG_USB_EHCI_MXC selects the old i.mx USB driver, which does not support
device tree.
Select the USB chipidea driver instead, so that USB can be functional on i.mx.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The em_x270_mci_setpower() and em_x270_usb_hub_init() functions
call regulator_enable(), which may return an error that must
be checked.
This changes the em_x270_usb_hub_init() function to bail out
if it fails, and changes the pxamci_platform_data->setpower
callback so that the a failed em_x270_mci_setpower call
can be propagated by the pxamci driver into the mmc core.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Mike Rapoport <mike@compulab.co.il>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: Chris Ball <cjb@laptop.org>
[olof: fixed order of regulator_enable() and test in em_x270_usb_hub_init]
Signed-off-by: Olof Johansson <olof@lixom.net>
Fix the following compilation warning:
arch/arm/mach-zynq/common.c:110:2: warning: initialization from incompatible pointer type [enabled by default]
arch/arm/mach-zynq/common.c:110:2: warning: (near initialization for ‘__mach_desc_XILINX_EP107.restart’) [enabled by default]
Signed-off-by: Vincent Stehlé <vincent.stehle@freescale.com>
Cc: Robin Holt <holt@sgi.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: trivial@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
Fix the following compilation warning:
arch/arm/mach-keystone/keystone.c:74:2: warning: initialization from incompatible pointer type [enabled by default]
arch/arm/mach-keystone/keystone.c:74:2: warning: (near initialization for ‘__mach_desc_KEYSTONE.restart’) [enabled by default]
Signed-off-by: Vincent Stehlé <vincent.stehle@freescale.com>
Cc: Robin Holt <holt@sgi.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: trivial@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit 7b6d864b48 (reboot: arm: change reboot_mode to use enum
reboot_mode) and ff701306cd (arm64: use common reboot infrastructure)
change the prototype of arm_pm_restart on arm and arm64.
Update xen_restart accordingly.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Commit ff70130 (arm64: use common reboot infrastructure) converted the
arm_pm_restart declaration to the new reboot infrastructure but missed
the actual definition.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Secondary CPUs write to __boot_cpu_mode with caches disabled, and thus a
cached value of __boot_cpu_mode may be incoherent with that in memory.
This could lead to a failure to detect mismatched boot modes.
This patch adds flushing to ensure that writes by secondaries to
__boot_cpu_mode are made visible before we test against it.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <cdall@cs.columbia.edu>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Recently we added an early quirk to detect 5500/5520 chipsets
with early revisions that had problems with irq draining with
interrupt remapping enabled:
commit 03bbcb2e7e
Author: Neil Horman <nhorman@tuxdriver.com>
Date: Tue Apr 16 16:38:32 2013 -0400
iommu/vt-d: add quirk for broken interrupt remapping on 55XX chipsets
It turns out this same problem is present in the intel X58
chipset as well. See errata 69 here:
http://www.intel.com/content/www/us/en/chipsets/x58-express-specification-update.html
This patch extends the pci early quirk so that the chip
devices/revisions specified in the above update are also covered
in the same way:
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Donald Dutile <ddutile@redhat.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Andrew Cooper <andrew.cooper3@citrix.com>
Cc: Malcolm Crossley <malcolm.crossley@citrix.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1374059639-8631-1-git-send-email-nhorman@tuxdriver.com
[ Small edits. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Midway adds new register fields to the coherency control registers, so
writing absolute values will break on Midway. Change the register
accesses to only modify the necessary and common fields in order to
support both Midway and Highbank.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
- Update the baseline so we need not rely on make
oldconfig so much
- MMC defconfig updates
- Activate NO_HZ_IDLE and HRTIMERS
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=XGIF
-----END PGP SIGNATURE-----
Merge tag 'nomadik-defconfig-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into fixes
From Linus Walleij:
This updates the Nomadik defconfig post-v3.11-rc1:
- Update the baseline so we need not rely on make
oldconfig so much
- MMC defconfig updates
- Activate NO_HZ_IDLE and HRTIMERS
* tag 'nomadik-defconfig-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: nomadik: configure for NO_HZ and HRTIMERS
ARM: nomadik: update defconfig base
ARM: nomadik: Update MMC defconfigs
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit 8ef6e6201b (ARM: footbridge: use
fixed PCI i/o mapping) broke booting on my netwinder. Before that,
everything boots fine. Since then, it crashes on boot.
With earlyprintk, I see it BUG-ing like so:
kernel BUG at lib/ioremap.c:27!
Internal error: Oops - BUG: 0 [#1] ARM
...
[<c0139b54>] (ioremap_page_range+0x128/0x154) from [<c02e6a6c>] (dc21285_setup+0xd0/0x114)
[<c02e6a6c>] (dc21285_setup+0xd0/0x114) from [<c02e4874>] (pci_common_init+0xa0/0x298)
[<c02e4874>] (pci_common_init+0xa0/0x298) from [<c02e793c>] (netwinder_pci_init+0xc/0x18)
[<c02e793c>] (netwinder_pci_init+0xc/0x18) from [<c02e27d0>] (do_one_initcall+0xb4/0x180)
...
Russell points out it's because of overlapping PCI mappings that was
added with the aforementioned commit. Rob thought the code would re-use
the static mapping, but that turns out to not be the case and instead
hits the BUG further down.
After deleting this hunk as suggested by Russel, the system boots up fine
again and all my PCI devices work (IDE, ethernet, the DC21285).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Cc: stable@vger.kernel.org # v3.5+
Signed-off-by: Olof Johansson <olof@lixom.net>
* A few device tree source fixes regarding pinctrl, clock, and pwm
backlight.
* Fixes imx28 and imx51 audio driver failure caused by sgtl5000 codec
driver change by supplying the correct clock for codec.
* imx6q emi_sel clock muxing and imx6q-iomuxc-gpr macro fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJR5B55AAoJEFBXWFqHsHzOEGoH/2DesLDZkQbUCn+w7Z3H7HYi
QAPeG1F/Ke3cBSaT+v/Z+46MgmU2gyQkxk08GRtPuVAZwCuWxSUN1H6+yakeBdHb
XGXR25RbbASIpYdYnC37eKiU2itiBmD7CRbWJ5xPHEluAgr47vr3OKfls6laii3b
nSM4sKz45PxBJ55M0qcE+A6oVdf9c+G0vm0aX14xEiLEUghB/U0KNKWp+B63hwfh
tg11gNwr2dO8jv51xpwJXH17juoZ46srOzmxERJm3j08JSz/tJSvIQajSsg54aLT
pAxToPAeuGGga5+7AanGT+repzZdd74Lp3U/lGw6WpaxLOpFf5Am3841O8qqCLw=
=q0LM
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-3.11' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo, imx fixes for 3.11:
- A few device tree source fixes regarding pinctrl, clock, and pwm
backlight.
- Fixes imx28 and imx51 audio driver failure caused by sgtl5000 codec
driver change by supplying the correct clock for codec.
- imx6q emi_sel clock muxing and imx6q-iomuxc-gpr macro fixes
* tag 'imx-fixes-3.11' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: dts: imx51-babbage: Pass a real clock to the codec
ARM i.MX53: mba53: Fix PWM backlight DT node
ARM: imx: fix vf610 enet module clock selection
ARM: mxs: saif0 is the clock provider to sgtl5000
ARM: i.MX6Q: correct emi_sel clock muxing
ARM i.MX6Q: Fix IOMUXC GPR1 defines for ENET_CLK_SEL and IPU1/2_MUX
ARM: i.MX27: Typo fix
ARM: imx27: Fix documentation for SPLL clock
ARM i.MX53: Fix UART pad configuration
From Tony Lindgren:
Omap fixes mostly to deal with the dropping of platform data for omap4,
and to make v7_defconfig bootable on omap4 SDP with nfsroot.
* tag 'omap-for-v3.11/fixes-against-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Provide alias to USB PHY clock
ARM: dts: Add missing vmmc2 regulator for twl
ARM: multi_v7: Enabled omap4430 sdp nfsroot
From Sekhar Nori:
DaVinci fixes for v3.11-rc2
The pull request includes fixes for sparse warnings, defconfig changes to
enable DMA usage on peripherals and removal of a duplicated include file.
* tag 'davinci-fixes-for-v3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: defconfig: enable EDMA driver
ARM: davinci: make file local variables static
ARM: edma: remove duplicated include from edma.c
Signed-off-by: Olof Johansson <olof@lixom.net>
Some of the ARM_ERRATA selection is not done in the initial SOC support
patches. This patch selects 2 new ARM_ERRATA's and removes one which was
actually fixed.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
[olof: reorder new errata entries]
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch fixes a bug in pinctrl setup of serial2 device, Some of the
pins in the pinctrl node of serial2 do not belong to that
pin-controller. This patch divides them in the pins into there
respective pin controller nodes.
Without this patch serial on StiH416-B2000 Board will not work as it
fails with:
"st-pinctrl pin-controller-rear.3: failed to get pin(99) name
st-pinctrl pin-controller-rear.3: maps: function serial2 group serial2-0
num 4
pinconfig core: failed to register map default (3): no group/pin given"
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit a469abd0f8 ("ARM: elf: add new hwcap for identifying atomic
ldrd/strd instructions") added a new hwcap to identify LPAE on CPUs
which support it. Whilst the hwcap data is correct, the string reported
in /proc/cpuinfo actually matches on HWCAP_VFPD32, which was missing
an entry in the string table.
This patch fixes this problem by adding a "vfpd32" string at the correct
offset, preventing us from falsely advertising LPAE on CPUs which do not
support it.
[will: added commit message]
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently, compare_cpu_mode_with_primary uses a mixture of macro
arguments and hardcoded registers, and does so incorrectly, as it
stores (__boot_cpu_mode_offset | BOOT_CPU_MODE_MISMATCH) to
(__boot_cpu_mode + &__boot_cpu_mode_offset), which could corrupt an
arbitrary portion of memory.
This patch fixes up compare_cpu_mode_with_primary to use the macro
arguments, correctly updating __boot_cpu_mode.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <cdall@cs.columbia.edu>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When map_lowmem() runs, and processes a memory bank whose start or end
is not section-aligned, memory must be allocated to store the 2nd-level
page tables. Those allocations are made by calling memblock_alloc().
At this point, the only memory that is free *and* mapped is memory which
has already been mapped by map_lowmem() itself. For this reason, we must
calculate the first point at which map_lowmem() will need to allocate
memory, and set the memblock allocation limit to a lower address, so that
memblock_alloc() is guaranteed to return memory that is already mapped.
This patch enhances sanity_check_meminfo() to calculate that memory
address, and pass it to memblock_set_current_limit(), rather than just
assuming the limit is arm_lowmem_limit.
The algorithm applied is:
* Default memblock_limit to arm_lowmem_limit in the absence of any other
limit; arm_lowmem_limit is the highest memory that is mapped by
map_lowmem().
* While walking the list of memblocks, if the start of a block is not
aligned, 2nd-level page tables will need to be allocated to map the
first few pages of the block. Hence, the memblock_limit must be before
the start of the block.
* Similarly, if the end of any block is not aligned, 2nd-level page
tables will need to be allocated to map the last few pages of the
block. Hence, the memblock_limit must point at the end of the block,
rounded down to section-alignment.
* The memory blocks are assumed to be sorted in address order, so the
first unaligned block start or end is used to set the limit.
With this algorithm, the start or end of almost any bank can be non-
section-aligned. The only exception is that the start of bank 0 must
be section-aligned, since otherwise memory would need to be allocated
when mapping the start of bank 0, which occurs before any free memory
is mapped.
[swarren, wrote commit description, rewrote calculation of memblock_limit]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit ae8a8b9553 ("ARM: 7691/1: mm: kill unused TLB_CAN_READ_FROM_L1_CACHE
and use ALT_SMP instead") added early function returns for page table
cache flushing operations on ARMv7 SMP CPUs.
Unfortunately, when targetting Thumb-2, these `mov pc, lr' sequences
assemble to 2 bytes which can lead to corruption of the instruction
stream after code patching.
This patch fixes the alternates to use wide (32-bit) instructions for
Thumb-2, therefore ensuring that the patching code works correctly.
Cc: <stable@vger.kernel.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This non-user visible option lacked any kind of documentation. This
is quite common for non-user visible options; certian people can't
understand the point of documenting such options with help text.
However, here we have a case in point: developers don't understand the
option either, as they were thinking that when the option is not set,
the decompressor should produce no output what so ever. This is
incorrect, as the purpose of this option is to control whether a
multiplatform kernel uses the kernel debugging macros to produce
output or not.
So let's document this via help rather than commentry to prevent others
falling into this misunderstanding.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
in drivers/pinctrl/sirf, pingroup name is cko0 and cko1, but in dts, they
are cko0 and cko1_rst. this patch fixes the error in dts.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
this patch adds the lost pin group which supports to let USP0 to simulate
a UART without hardware flow control.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Enable MMC_UNSAFE_RESUME to accomplish a proper suspend/resume cycle
for SD/SDIO/(e)MMC.
ARMMMCI host driver supports clock gating through runtime PM, thus
MMC_CLKGATE is not needed. Moreover ARMMMCI can do scatter-gather which
means we can explicity disable MMC_BLOCK_BOUNCE, since it's default
enabled, to skip unnecessary bounce buffer copying.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull UML fixes from Richard Weinberger:
"Special thanks goes to Toralf Föster for continuously testing UML and
reporting issues!"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
um: remove dead code
um: siginfo cleanup
uml: Fix which_tmpdir failure when /dev/shm is a symlink, and in other edge cases
um: Fix wait_stub_done() error handling
um: Mark stub pages mapping with VM_PFNMAP
um: Fix return value of strnlen_user()
Pull MIPS fixes from Ralf Baechle:
"MIPS fixes for 3.11. Half of then is for Netlogic the remainder
touches things across arch/mips.
Nothing really dramatic and by rc1 standards MIPS will be in fairly
good shape with this applied. Tested by building all MIPS defconfigs
of which with this pull request four platforms won't build. And yes,
it boots also on my favorite test systems"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: kvm: Kconfig: Drop HAVE_KVM dependency from VIRTUALIZATION
MIPS: Octeon: Fix DT pruning bug with pip ports
MIPS: KVM: Mark KVM_GUEST (T&E KVM) as BROKEN_ON_SMP
MIPS: tlbex: fix broken build in v3.11-rc1
MIPS: Netlogic: Add XLP PIC irqdomain
MIPS: Netlogic: Fix USB block's coherent DMA mask
MIPS: tlbex: Fix typo in r3000 tlb store handler
MIPS: BMIPS: Fix thinko to release slave TP from reset
MIPS: Delete dead invocation of exception_exit().
- Fixes (user cache maintenance fault handling, !COMPAT compilation, CPU
online and interrupt hanlding).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)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=M4kj
-----END PGP SIGNATURE-----
Merge tag 'arm64-stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64
Pull arm64 fixes from Catalin Marinas:
- Post -rc1 update to the common reboot infrastructure.
- Fixes (user cache maintenance fault handling, !COMPAT compilation,
CPU online and interrupt hanlding).
* tag 'arm64-stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
arm64: use common reboot infrastructure
arm64: mm: don't treat user cache maintenance faults as writes
arm64: add '#ifdef CONFIG_COMPAT' for aarch32_break_handler()
arm64: Only enable local interrupts after the CPU is marked online
Pull s390 fixes from Martin Schwidefsky:
"An update for the BFP jit to the latest and greatest, two patches to
get kdump working again, the random-abort ptrace extention for
transactional execution, the z90crypt module alias for ap and a tiny
cleanup"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/zcrypt: Alias for new zcrypt device driver base module
s390/kdump: Allow copy_oldmem_page() copy to virtual memory
s390/kdump: Disable mmap for s390
s390/bpf,jit: add pkt_type support
s390/bpf,jit: address randomize and write protect jit code
s390/bpf,jit: use generic jit dumper
s390/bpf,jit: call module_free() from any context
s390/qdio: remove unused variable
s390/ptrace: PTRACE_TE_ABORT_RAND
This kernel/user split was done long ago for other architectures.
Signed-off-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
The code as written is correct, and will be used by QEMU emulation.
Signed-off-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Acked-by: Phil Carmody <pc+lkml@asdf.org>
Reviewed-and-Tested-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Having unwind info past the PALcode generated stack frame makes
debugging the kernel significantly easier.
Acked-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Reviewed-and-Tested-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Use ll/sc loops instead of C loops around cmpxchg.
Update the atomic64_add_unless block comment to match the code.
Reviewed-and-Tested-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Reviewed-and-Tested-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
The arch_{spin,read,write}_relax macros are not used anywhere in the
kernel and are typically just aliases for cpu_relax().
This patch removes the unused definitions for Alpha.
Cc: Al Viro <viro@zeniv.linux.org.uk>
Reviewed-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
For sending message:
*(unsigned int *)&cpu->ipc_buffer[0] = len;
cp1 = (char *) &cpu->ipc_buffer[1];
But for receive message:
cnt = cpu->ipc_buffer[0] >> 32;
...
cp1 = (char *) &cpu->ipc_buffer[11];
They are not pairs, it is typo issue of the redundency '1'.
So need use '1' instead of '11'.
Reviewed-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Chen Gang <gang.chen@asianux.com>
When sending message in send_secondary_console_msg(), the length is not
include the NUL byte, and also not copy NUL to 'ipc_buffer'.
When receive message in recv_secondary_console_msg(), the 'cnt' also
excludes NUL.
So when get string from ipc_buffer, it may not be NUL terminated.
Then use memcpy() instead of strcpy(), and set last byte NUL.
Reviewed-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Use the new vsprintf extension to avoid any possible
message interleaving.
Reviewed-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Joe Perches <joe@perches.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=+0Dk
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fix from Paolo Bonzini:
"This single patch fixes a regression caused by one of the
optimizations introduced in 3.11, which is generally visible only on
AMD processors"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: MMU: avoid fast page fault fixing mmio page fault
- Two cpufreq commits from the 3.10 cycle introduced regressions.
The first of them was buggy (it did way much more than it needed
to do) and the second one attempted to fix an issue introduced by
the first one. Fixes from Srivatsa S Bhat revert both.
- If autosleep triggers during system shutdown and the shutdown
callbacks of some device drivers have been called already, it may
crash the system. Fix from Liu Shuo prevents that from happening
by making try_to_suspend() check system_state.
- The ACPI memory hotplug driver doesn't clear its driver_data on
errors which may cause a NULL poiter dereference to happen later.
Fix from Toshi Kani.
- The ACPI namespace scanning code should not try to attach scan
handlers to device objects that have them already, which may confuse
things quite a bit, and it should rescan the whole namespace branch
starting at the given node after receiving a bus check notify event
even if the device at that particular node has been discovered
already. Fixes from Rafael J Wysocki.
- New ACPI video blacklist entry for a system whose initial backlight
setting from the BIOS doesn't make sense. From Lan Tianyu.
- Garbage string output avoindance for ACPI PNP from Liu Shuo.
- Two Kconfig fixes for issues introduced recently in the s3c24xx
cpufreq driver (when moving the driver to drivers/cpufreq) from
Paul Bolle.
- Trivial comment fix in pm_wakeup.h from Chanwoo Choi.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=IUmn
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These are fixes collected over the last week, most importnatly two
cpufreq reverts fixing regressions introduced in 3.10, an autoseelp
fix preventing systems using it from crashing during shutdown and two
ACPI scan fixes related to hotplug.
Specifics:
- Two cpufreq commits from the 3.10 cycle introduced regressions.
The first of them was buggy (it did way much more than it needed to
do) and the second one attempted to fix an issue introduced by the
first one. Fixes from Srivatsa S Bhat revert both.
- If autosleep triggers during system shutdown and the shutdown
callbacks of some device drivers have been called already, it may
crash the system. Fix from Liu Shuo prevents that from happening
by making try_to_suspend() check system_state.
- The ACPI memory hotplug driver doesn't clear its driver_data on
errors which may cause a NULL poiter dereference to happen later.
Fix from Toshi Kani.
- The ACPI namespace scanning code should not try to attach scan
handlers to device objects that have them already, which may
confuse things quite a bit, and it should rescan the whole
namespace branch starting at the given node after receiving a bus
check notify event even if the device at that particular node has
been discovered already. Fixes from Rafael J Wysocki.
- New ACPI video blacklist entry for a system whose initial backlight
setting from the BIOS doesn't make sense. From Lan Tianyu.
- Garbage string output avoindance for ACPI PNP from Liu Shuo.
- Two Kconfig fixes for issues introduced recently in the s3c24xx
cpufreq driver (when moving the driver to drivers/cpufreq) from
Paul Bolle.
- Trivial comment fix in pm_wakeup.h from Chanwoo Choi"
* tag 'pm+acpi-3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / video: ignore BIOS initial backlight value for Fujitsu E753
PNP / ACPI: avoid garbage in resource name
cpufreq: Revert commit 2f7021a8 to fix CPU hotplug regression
cpufreq: s3c24xx: fix "depends on ARM_S3C24XX" in Kconfig
cpufreq: s3c24xx: rename CONFIG_CPU_FREQ_S3C24XX_DEBUGFS
PM / Sleep: Fix comment typo in pm_wakeup.h
PM / Sleep: avoid 'autosleep' in shutdown progress
cpufreq: Revert commit a66b2e to fix suspend/resume regression
ACPI / memhotplug: Fix a stale pointer in error path
ACPI / scan: Always call acpi_bus_scan() for bus check notifications
ACPI / scan: Do not try to attach scan handlers to devices having them
Commit 7b6d864b48 (reboot: arm: change reboot_mode to use enum
reboot_mode) changed the way reboot is handled on arm, which has a
direct impact on arm64 as we share the reset driver on the VE platform.
The obvious fix is to move arm64 to use the same infrastructure.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
[catalin.marinas@arm.com: removed reboot_mode = REBOOT_HARD default setting]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
On arm64, cache maintenance faults appear as data aborts with the CM
bit set in the ESR. The WnR bit, usually used to distinguish between
faulting loads and stores, always reads as 1 and (slightly confusingly)
the instructions are treated as reads by the architecture.
This patch fixes our fault handling code to treat cache maintenance
faults in the same way as loads.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
If 'COMPAT' not defined, aarch32_break_handler() cannot pass compiling,
and it can work independent with 'COMPAT', so remove dummy definition.
The related error:
arch/arm64/kernel/debug-monitors.c:249:5: error: redefinition of ‘aarch32_break_handler’
In file included from arch/arm64/kernel/debug-monitors.c:29:0:
/root/linux-next/arch/arm64/include/asm/debug-monitors.h:89:12: note: previous definition of ‘aarch32_break_handler’ was here
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
There is a slight chance that (timer) interrupts are triggered before a
secondary CPU has been marked online with implications on softirq thread
affinity.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Kirill Tkhai <tkhai@yandex.ru>
Virtualization does not always need KVM capabilities so drop the
dependency. The KVM symbol already depends on HAVE_KVM.
Fixes the following problem on a randconfig:
warning: (REMOTEPROC && RPMSG) selects VIRTUALIZATION which has unmet direct
dependencies (HAVE_KVM)
warning: (REMOTEPROC && RPMSG) selects VIRTUALIZATION which has unmet
direct dependencies (HAVE_KVM)
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Acked-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5443/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Currently we use both struct siginfo and siginfo_t.
Let's use struct siginfo internally to avoid ongoing
compiler warning. We are allowed to do so because
struct siginfo and siginfo_t are equivalent.
Signed-off-by: Richard Weinberger <richard@nod.at>
During the pruning of the device tree octeon_fdt_pip_iface() is called
for each PIP interface and every port up to the port count is removed
from the device tree. However, the count was set to the return value of
cvmx_helper_interface_enumerate() which doesn't actually return the
count but just returns zero on success. This effectively removed *all*
ports from the tree.
Use cvmx_helper_ports_on_interface() instead to fix this. This
successfully restores the 3 ports of my ERLite-3 and fixes the "kernel
assigns random MAC addresses" issue.
Signed-off-by: Faidon Liambotis <paravoid@debian.org>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5587/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
which_tmpdir did the wrong thing if /dev/shm was a symlink (e.g., to /run/shm),
if there were multiple mounts on top of each other, if the mount(s) were
obscured by a later mount, or if /dev/shm was a prefix of another mount point.
This fixes these cases. Applies to 3.9.6.
Signed-off-by: Tristan Schmelcher <tschmelcher@google.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
If we die within a stub handler we only way to reliable
kill the (obviously) dying uml guest process is killing
it's host twin on the host side.
Signed-off-by: Richard Weinberger <richard@nod.at>
Ensure that a process cannot destroy his stub pages with
using MADV_DONTNEED and friends.
Reported-by: toralf.foerster@gmx.de
Signed-off-by: Richard Weinberger <richard@nod.at>
In case of an error it must not return -EFAULT.
Return 0 like all other archs do.
Reported-by: toralf.foerster@gmx.de
Signed-off-by: Richard Weinberger <richard@nod.at>
Make KVM_GUEST depend on BROKEN_ON_SMP so that it cannot be enabled with
SMP.
SMP kernels use ll/sc instructions for an atomic section in the tlb fill
handler, with a tlbp instruction contained in the middle. This cannot be
emulated with trap & emulate KVM because the tlbp instruction traps and
the eret to return to the guest code clears the LLbit which makes the sc
instruction always fail.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Sanjay Lal <sanjayl@kymasys.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/5588/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 6ba045f9fb (MIPS: Move generated code
to .text for microMIPS) deleted tlbmiss_handler_setup_pgd_array, but some
references were not converted. Fix that to enable building a MIPS kernel.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Jayachandran C. <jchandra@broadcom.com>
Acked-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5589/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a legacy irq domain for the XLP PIC interrupts. This will be used
when interrupts are assigned from the device tree. This change is required
after commit c5cdc67 "irqdomain: Remove temporary MIPS workaround code".
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Cc: Jayachandran C <jchandra@broadcom.com>
Patchwork: https://patchwork.linux-mips.org/patch/5597/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The on-chip USB controller on Netlogic XLP does not suppport
DMA beyond 32-bit physical address. Set the coherent_dma_mask
of the USB in its PCI fixup to support this.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C. <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5596/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
commit 6ba045f (MIPS: Move generated code to .text for microMIPS)
causes a panic at boot. The handler builder should test against
handle_tlbs_end, not handle_tlbs.
Signed-off-by: Tony Wu <tung7970@gmail.com>
Acked-by: Jayachandran C. <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5600/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 4df715aa ["MIPS: BMIPS: support booting from physical CPU other
than 0"] introduced a thinko which will prevents slave CPUs from being
released from reset on systems where we boot from TP0. The problem is
that we are checking whether the slave CPU logical CPU map is 0, which
is never true for systems booting from TP0, so we do not release the
slave TP from reset and we are just stuck. Fix this by properly checking
that the CPU we intend to boot really is the physical slave CPU (logical
and physical value being 1).
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: blogic@openwrt.org
Cc: jogo@openwrt.org
Cc: cernekee@gmail.com
Cc: Florian Fainelli <florian@openwrt.org>
Patchwork: https://patchwork.linux-mips.org/patch/5598/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull x86 fixes from Peter Anvin:
"Trying again to get the fixes queue, including the fixed IDT alignment
patch.
The UEFI patch is by far the biggest issue at hand: it is currently
causing quite a few machines to boot. Which is sad, because the only
reason they would is because their BIOSes touch memory that has
already been freed. The other major issue is that we finally have
tracked down the root cause of a significant number of machines
failing to suspend/resume"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Make sure IDT is page aligned
x86, suspend: Handle CPUs which fail to #GP on RDMSR
x86/platform/ce4100: Add header file for reboot type
Revert "UEFI: Don't pass boot services regions to SetVirtualAddressMap()"
efivars: check for EFI_RUNTIME_SERVICES
Fix the the gpio reg address for the device tree entry.
Signed-off-by: Rohit Vaswani <rvaswani@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Pull phase two of __cpuinit removal from Paul Gortmaker:
"With the __cpuinit infrastructure removed earlier, this group of
commits only removes the function/data tagging that was done with the
various (now no-op) __cpuinit related prefixes.
Now that the dust has settled with yesterday's v3.11-rc1, there
hopefully shouldn't be any new users leaking back in tree, but I think
we can leave the harmless no-op stubs there for a release as a
courtesy to those who still have out of tree stuff and weren't paying
attention.
Although the commits are against the recent tag to allow for minor
context refreshes for things like yesterday's v3.11-rc1~ slab content,
the patches have been largely unchanged for weeks, aside from such
trivial updates.
For detail junkies, the largely boring and mostly irrelevant history
of the patches can be viewed at:
http://git.kernel.org/cgit/linux/kernel/git/paulg/cpuinit-delete.git
If nothing else, I guess it does at least demonstrate the level of
involvement required to shepherd such a treewide change to completion.
This is the same repository of patches that has been applied to the
end of the daily linux-next branches for the past several weeks"
* 'cpuinit_phase2' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (28 commits)
block: delete __cpuinit usage from all block files
drivers: delete __cpuinit usage from all remaining drivers files
kernel: delete __cpuinit usage from all core kernel files
rcu: delete __cpuinit usage from all rcu files
net: delete __cpuinit usage from all net files
acpi: delete __cpuinit usage from all acpi files
hwmon: delete __cpuinit usage from all hwmon files
cpufreq: delete __cpuinit usage from all cpufreq files
clocksource+irqchip: delete __cpuinit usage from all related files
x86: delete __cpuinit usage from all x86 files
score: delete __cpuinit usage from all score files
xtensa: delete __cpuinit usage from all xtensa files
openrisc: delete __cpuinit usage from all openrisc files
m32r: delete __cpuinit usage from all m32r files
hexagon: delete __cpuinit usage from all hexagon files
frv: delete __cpuinit usage from all frv files
cris: delete __cpuinit usage from all cris files
metag: delete __cpuinit usage from all metag files
tile: delete __cpuinit usage from all tile files
sh: delete __cpuinit usage from all sh files
...
The kdump mmap patch series (git commit 83086978c6) changed the
requirements for copy_oldmem_page(). Now this function is used for copying
to virtual memory.
So implement vmalloc support for the s390 version of copy_oldmem_page().
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This is the s390 variant of 314beb9b "x86: bpf_jit_comp: secure bpf
jit against spraying attacks".
With this change the whole jit code and literal pool will be write
protected after creation. In addition the start address of the jit
code won't be always on a page boundary anymore.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This is the s390 backend of 79617801 "filter: bpf_jit_comp: refactor
and unify BPF JIT image dump output".
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The workqueue workaround is no longer needed. Same as 5199dfe531
"sparc: bpf_jit_comp: can call module_free() from any context".
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently, fast page fault incorrectly tries to fix mmio page fault when
the generation number is invalid (spte.gen != kvm.gen). It then returns
to guest to retry the fault since it sees the last spte is nonpresent.
This causes an infinite loop.
Since fast page fault only works for direct mmu, the issue exists when
1) tdp is enabled. It is only triggered only on AMD host since on Intel host
the mmio page fault is recognized as ept-misconfig whose handler call
fault-page path with error_code = 0
2) guest paging is disabled. Under this case, the issue is hardly discovered
since paging disable is short-lived and the sptes will be invalid after
memslot changed for 150 times
Fix it by filtering out MMIO page faults in page_fault_can_be_fast.
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
panic() doesn't return so this call was useless.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reported-by: Alexander Sverdlin <alexander.sverdlin@nsn.com>
Since the IDT is referenced from a fixmap, make sure it is page aligned.
Merge with 32-bit one, since it was already aligned to deal with F00F
bug. Since bss is cleared before IDT setup, it can live there. This also
moves the other *_idt_table variables into common locations.
This avoids the risk of the IDT ever being moved in the bss and having
the mapping be offset, resulting in calling incorrect handlers. In the
current upstream kernel this is not a manifested bug, but heavily patched
kernels (such as those using the PaX patch series) did encounter this bug.
The tables other than idt_table technically do not need to be page
aligned, at least not at the current time, but using a common
declaration avoids mistakes. On 64 bits the table is exactly one page
long, anyway.
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: http://lkml.kernel.org/r/20130716183441.GA14232@www.outflux.net
Reported-by: PaX Team <pageexec@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Kconfig symbol S3C24XX_PLL depends on ARM_S3C24XX. But that symbol
doesn't exist. Commit f023f8dd59 ("cpufreq: s3c24xx: move cpufreq
driver to drivers/cpufreq"), which added this issue, makes it clear
that ARM_S3C24XX_CPUFREQ was intended here.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Enable EDMA dmaengine driver by default in DaVinci
defconfig files as it is required for DMA support
on MMC/SD, SPI etc.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Make file local variables static in mach-davinci.
This fixes sparse warnings of the form:
arch/arm/mach-davinci/dm355.c:863:27: warning: symbol 'dm355_venc_pdata' was not declared. Should it be static?
Cc: Prabhakar Lad <prabhakar.csengg@gmail.com>
Acked-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Till the OMAP clocks are correctly defined in device tree, use
this temporary hack to provide clock alias to the USB PHY clocks.
Without this, USB Host & Ethernet will not be functional with
device tree boots on Panda and uEVM.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The patch implements a s390 specific ptrace request
PTRACE_TE_ABORT_RAND to modify the randomness of spontaneous
aborts of memory transactions of the transaction execution
facility. The data argument of the ptrace request is used to
specify the levels of randomness, 0 for normal operation, 1 to
abort every transaction at a random instruction, and 2 to abort
a random transaction at a random instruction. The default is 0
for normal operation.
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Michael Mueller <mimu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Allow 64-bit DMA addresses if LPAE is enabled on EXYNOS5440.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
On EXYNOS5440 there is DRAM on the 36-bit address range. Hence
this patch converts the MAX_PHYSMEM_BITS macro to 36 if LPAE is
enabled for the ARM architecture.
The conventional section size on EXYNOS is 256M due to sparsemem.
Since EXYNOS5440 has memory in multiples of 1G in 32-bit and 36-bit
range, this has now been modified to 31.
Signed-off-by: Subash Patel <subash.rp@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
EXYNOS5440 doesn't support PM and current single image for EXYNOS
will be break without this patch. Actually, SSDK5440 cannot boot
without this so this should be merged during rc.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
There are CPUs which have errata causing RDMSR of a nonexistent MSR to
not fault. We would then try to WRMSR to restore the value of that
MSR, causing a crash. Specifically, some Pentium M variants would
have this problem trying to save and restore the non-existent EFER,
causing a crash on resume.
Work around this by making sure we can write back the result at
suspend time.
Huge thanks to Christian Sünkenberg for finding the offending erratum
that finally deciphered the mystery.
Reported-and-tested-by: Johan Heinrich <onny@project-insanity.org>
Debugged-by: Christian Sünkenberg <christian.suenkenberg@student.kit.edu>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Link: http://lkml.kernel.org/r/51DDC972.3010005@student.kit.edu
Cc: <stable@vger.kernel.org> # v3.7+
On imx51_babbage the codec clock is activated via GPIO4_26.
Provide a real clock to the sgtl5000 codec via device tree.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
By adding support for OCP2SCP, SPI and KS8851 I can also boot test
multi_v7_defconfig easily.
Note that if using an older u-boot, CONFIG_ARM_ATAG_DTB_COMPAT=y
may also be needed for the appended DTB based booting.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The i.MX53 PWM controller uses two cells to describe the PWM specifier.
Remove the extra unused values from the backlight DT node pwms property.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The fec/enet driver calculates MDC rate with the formula below.
ref_freq / ((MII_SPEED + 1) x 2)
The ref_freq here is the fec internal module clock, which is missing
from clk-vf610 clock driver right now. And clk-vf610 driver mistakenly
supplies RMII clock (50 MHz) as the source to fec. This results in the
situation that fec driver gets ref_freq as 50 MHz, while physically it
runs at 66 MHz (fec module clock physically sources from ipg which runs
at 66 MHz). That's why software expects MDC runs at 2.5 MHz, while the
measurement tells it runs at 3.3 MHz. And this causes the PHY KSZ8041
keeps swithing between Full and Half mode as below.
libphy: 400d0000.etherne:00 - Link is Up - 100/Full
libphy: 400d0000.etherne:00 - Link is Up - 100/Half
libphy: 400d0000.etherne:00 - Link is Up - 100/Full
libphy: 400d0000.etherne:00 - Link is Up - 100/Half
libphy: 400d0000.etherne:00 - Link is Up - 100/Full
libphy: 400d0000.etherne:00 - Link is Up - 100/Half
Add the missing module clock for ENET0 and ENET1, and correct the clock
supplying in device tree to fix above issue.
Thanks to Alison Wang <b18965@freescale.com> for debugging the issue.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
