Johan Hedberg
a087a98e07
Bluetooth: btusb: Fix race when waiting for BTUSB_DOWNLOADING
...
The test for BTUSB_DOWNLOADING must be after adding to the wait queue
and setting the TASK_INTERRUPTIBLE state. Otherwise the flag may get
cleared after we test for it and we end up getting a timeout since
schedule_timeout() waits for the full duration. This patch uses a
wait_on_bit_timeout() + wake_up_bit(). To perform the task both
race-free as well as in a much simpler way.
Since there's no global wait_on_bit_timeout() helper yet (even though
all the building blocks for it are in place) this patch creates a
temporary local btusb copy of it until the global one has made it to
upstream trees.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-01-30 11:03:19 +01:00
Marcel Holtmann
74d9daafa5
Bluetooth: btusb: Limit hardware error handling to Intel Snowfield Peak
...
In general all Intel Bluetooth devices support retrieving of additional
exception information. However for older generations including Wilkens
Peak and Stone Peak it is not as simple. So for now only enable the
Intel specific error handling for Snowfield Peak and later devices.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-01-30 10:59:32 +02:00
Jakub Pawlowski
79f0c87d9f
Bluetooth: Set HCI_QUIRK_STRICT_DUPLICATE_FILTER for BTUSB_ATH3012
...
The Bluetooth controllers from Atheros use a strict scanning filter
policy that filters based on Bluetooth device addresses and not on
RSSI. So tell the core about this.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-01-29 20:11:54 +01:00
Marcel Holtmann
893ba5440a
Bluetooth: btusb: Add support for USB based AMP controllers
...
The Bluetooth HCI transport specification for USB device defines on how
a standard AMP controller is identified and operated. This patch adds
the needed handling to hook it up to the Bluetooth stack.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-01-29 09:27:50 +02:00
Marcel Holtmann
d0ac9eb72b
Bluetooth: btusb: Ignore unknown Intel devices with generic descriptor
...
The Intel Bluetooth devices use the generic USB device/interface class
descriptors that are assigned to Bluetooth H:2 conforming transports.
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
However newer chips have a bootloader stage and require firmware to
be loaded before they are functional. To avoid any confusion for the
users, just ignore unknown Intel Bluetooth devices.
All the released Intel Bluetooth devices have an entry in the device
table identifying their setup and support requirements. The advantage
here is that older kernel can be booted with newer devices without
causing any disturbance.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-01-29 08:24:14 +02:00
Marcel Holtmann
cb1ee89f95
Bluetooth: btusb: Sort USB_DEVICE entries for Marvell by vendor id
...
New entries to the USB blacklist/quirk device table should be sorted
by USB vendor id. Fix the recent entry fro Marvell devices.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-01-29 08:24:12 +02:00
Marcel Holtmann
385a768c3b
Bluetooth: btusb: Provide hardware error handler for Intel devices
...
The Intel Bluetooth controllers can provide an additional exception
info string when a hardware error event occurs. The core will now
call hdev->hw_error to let the driver read out this information.
This change will cause a reset of the hardware to bring it back
into functional state and then read the Intel exception info
string and print it along with the error information.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-01-28 21:26:25 +01:00
Johan Hedberg
838f66e3ab
Bluetooth: btusb: Remove redundant call to btusb_free_frags()
...
The btusb_disconnect() callback calls hci_unregister_dev() which in turn
calls btusb_close() if the HCI device is powered. The btusb_close()
function in turn will call btusb_free_frags(). It's therefore
unnecessary to have another call to btusb_free_frags() in the
btusb_disconnect() function. Besides the redundancy the second call
seems to also cause some strange stability issues which this patch then
also fixes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-01-28 21:26:22 +01:00
Marcel Holtmann
ce6bb9297c
Bluetooth: btusb: Handle out of order firmware loading complete event
...
When loading the Intel firmware it can happen that the firmware loading
complete vendor event arrives before the command complete event for the
last firmware fragment.
< HCI Command: Vendor (0x3f|0x0009) plen 7
01 02 fc 03 00 00 00
> HCI Event: Vendor (0xff) plen 5
06 00 00 00 00
> HCI Event: Command Complete (0x0e) plen 4
Vendor (0x3f|0x0009) ncmd 31
Status: Success (0x00)
This is mainly caused by the fact that the vendor command and its
command complete event are transported over the bulk endpoints. The
firmware loading complete event however is send over the interrupt
endpoint. So with just bad timing one event arrives before the other.
Currently the code does not account for it. There are precautions for
receiving firmware loading complete event quickly, but not for receiving
it before the command complete.
Introduce an extra flag that tracks when the firmware sending has
completed from the driver point of view and track the completion of
the firmware loading procedure with a different flag. That way the
wakeup can be handled properly.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-01-28 21:26:21 +01:00
Marcel Holtmann
cda0dd7809
Bluetooth: btusb: Add firmware loading for Intel Snowfield Peak devices
...
The Intel Snowfield Peak devices do not come with Bluetooth firmware
loaded and thus require a full download of the operational Bluetooth
firmware when the device is connected via USB.
Snowfield Peak devices start with a bootloader mode that only accepts
a very limited set of HCI commands. The supported commands are enough
to identify the hardware and select the right firmware to load.
Previous patches to the btusb driver allow overwriting the handling
for bulk receive endpoint packets and HCI events processing. The
firmware loading makes heavy use of these new internal callbacks.
This patch also introduces additional internal states to track if the
device is in bootloader or operational mode. This allows for correct
feedback about the firmware loading procedure.
Output from /sys/kernel/debug/usb/devices for this device:
T: Bus=02 Lev=02 Prnt=02 Port=05 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=8087 ProdID=0a2b Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Based-on-patch-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-01-28 21:25:50 +01:00
Marcel Holtmann
d049f4e513
Bluetooth: btusb: Add support for Dynex/Insignia USB dongles
...
The Dynex/Insignia USB dongles are Broadcom BCM20702B0 based and require
firmware update before operation.
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=19ff ProdID=0239 Rev= 1.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Since this is an unsual USB vendor ID (0x19ff), these dongles are added
via USB_DEVICE macro and not USB_VENDOR_AND_INTERFACE_INFO as done for
mainstream Broadcom based dongles.
The latest known working firmware is BCM20702B0_002.001.014.0527.0557.hex
which needs to be converted using hex2hcd utility and then installed
as /lib/firmware/brcm/BCM20702A0-19ff-0239.hcd to make this device fully
operational.
Bluetooth: hci0: BCM: patching hci_ver=06 hci_rev=2000 lmp_ver=06 lmp_subver=410e
Bluetooth: hci0: BCM: firmware hci_ver=06 hci_rev=222d lmp_ver=06 lmp_subver=410e
With this firmware the device reports support for connectionless slave
broadcast (master and slave) feature used by 3D Glasses and TVs.
< HCI Command: Read Local Extended Features (0x04|0x0004) plen 1
Page: 2
> HCI Event: Command Complete (0x0e) plen 14
Read Local Extended Features (0x04|0x0004) ncmd 1
Status: Success (0x00)
Page: 2/2
Features: 0x0f 0x00 0x00 0x00 0x00 0x00 0x00 0x00
Connectionless Slave Broadcast - Master
Connectionless Slave Broadcast - Slave
Synchronization Train
Synchronization Scan
However there are some flaws with this feature. The Set Event Mask Page 2
command is actually not supported and with that all connectionless slave
broadcast events are always enabled.
< HCI Command: Set Event Mask Page 2 (0x03|0x0063) plen 8
Mask: 0x00000000000f0000
Synchronization Train Received
Connectionless Slave Broadcast Receive
Connectionless Slave Broadcast Timeout
Truncated Page Complete
> HCI Event: Command Complete (0x0e) plen 4
Set Event Mask Page 2 (0x03|0x0063) ncmd 1
Status: Unknown HCI Command (0x01)
In addition the Synchronization Train Received event is actually broken
on this controller. It mixes up the order of parameters. According to the
Bluetooth Core specification the fields are like this:
struct hci_ev_sync_train_received {
__u8 status;
bdaddr_t bdaddr;
__le32 offset;
__u8 map[10];
__u8 lt_addr;
__le32 instant;
__le16 interval;
__u8 service_data;
} __packed;
This controller however sends the service_data as 5th parameter instead
of having it as last parameter.
struct hci_ev_sync_train_received {
__u8 status;
bdaddr_t bdaddr;
__le32 offset;
__u8 map[10];
__u8 service_data;
__u8 lt_addr;
__le32 instant;
__le16 interval;
} __packed;
So anybody trying to use this hardware for utilizing connectionless slave
broadcast receivers (aka 3D Glasses), be warned about this shortcoming.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org
2015-01-27 13:05:22 +02:00
Rick Dunn
9a5abdaaf9
Bluetooth: btusb: Add Broadcom patchram support for ASUSTek devices
...
T: Bus=03 Lev=01 Prnt=01 Port=06 Cnt=02 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0b05 ProdID=17cf Rev= 1.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
S: SerialNumber=54271E3298CD
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Firmware is extracted from the latest Broadcom BCM4352 Windows driver
by extracting the zip and searching the .hex file names for '17cf'.
The hex file must then be converted to hcd format using the hex2hcd
utility and then moved to /lib/firmware/brcm/.
Signed-off-by: Rick Dunn <rick@rickdunn.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
2015-01-21 06:05:38 +01:00
Dmitry Tunin
033efa920a
Bluetooth: ath3k: Add support of AR3012 bluetooth 13d3:3423 device
...
Add support of 13d3:3423 device.
BugLink: https://bugs.launchpad.net/bugs/1411193
T: Bus=01 Lev=02 Prnt=03 Port=00 Cnt=01 Dev#= 5 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3423 Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
2015-01-21 06:05:37 +01:00
Marcel Holtmann
97307f51d7
Bluetooth: btusb: Add internal recv_event callback for event processing
...
Some new upcoming drivers need to process HCI events or take extra
actions based on them before handing the event to the Bluetooth core
for processing. The new recv_event callback allows exactly such an
internal behavior.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-01-14 10:01:32 +02:00
Marcel Holtmann
661cf88acd
Bluetooth: Use HCI_QUIRK_FIXUP_INQUIRY_MODE for Silicon Wave devices
...
The Silicon Wave based devices do support Inquiry Result with RSSI and
so let the core know to enable them.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-01-03 22:31:11 +02:00
Marcel Holtmann
4fcef8ed75
Bluetooth: Fix issue with Roper Class 1 Bluetooth Dongle
...
The Roper Class 1 Bluetooth Dongle is another device that claims to
support Bluetooth 1.2 specification, but does not support the HCI
command for reading the local supported commands.
< HCI Command: Read Local Version Information (0x04|0x0001) plen 0
> HCI Event: Command Complete (0x0e) plen 12
Read Local Version Information (0x04|0x0001) ncmd 1
status 0x00
HCI Version: 1.2 (0x2) HCI Revision: 0x0
LMP Version: 1.2 (0x2) LMP Subversion: 0x757
Manufacturer: Silicon Wave (11)
It clearly claims Bluetooth 1.2 support and in that regard has the
same issue as the AVM BlueFritz! USB devices (Silicon Wave based),
but the HCI Read Local Supported Commands command fails.
< HCI Command: Read Local Supported Commands (0x04|0x0002) plen 0
> HCI Event: Command Status (0x0f) plen 4
Read Local Supported Commands (0x04|0x0002) status 0x01 ncmd 1
Error: Unknown HCI Command
Use the HCI_QUIRK_BROKEN_LOCAL_COMMANDS quirk for these devices and
the failing command will be skipped.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-01-02 22:22:04 +01:00
Marcel Holtmann
d57dbe779e
Bluetooth: btusb: Set the HCI_QUIRK_BROKEN_LOCAL_COMMANDS quirk
...
The AVM BlueFritz! 2.0 USB dongles do not support the HCI command for
reading the local supported commands. So set this quirk to let the
core know about it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2014-12-26 20:16:13 +02:00
Toshi Kikuchi
5859223e0c
Bluetooth: btusb: support public address configuration for ath3012
...
Set hdev->set_bdaddr handler for ath3012. It sends the vendor specific HCI
command to change the public address. The change doesn't persist across
power cycle.
Signed-off-by: Toshi Kikuchi <toshik@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-12-18 22:42:49 +01:00
Janne Heikkinen
134d3b3550
Bluetooth: Add USB device 04ca:3010 as Atheros AR3012
...
Asus X553MA has USB device 04ca:3010 that is Atheros AR3012
or compatible.
Device from /sys/kernel/debug/usb/devices:
T: Bus=01 Lev=02 Prnt=02 Port=03 Cnt=02 Dev#= 27 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=04ca ProdID=3010 Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Janne Heikkinen <janne.m.heikkinen@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-12-09 08:16:18 +01:00
Heinrich Siebmanns
6029ddc233
Bluetooth: Add support for Broadcom BCM20702A0 variants firmware download
...
This requires the flag BTUSB_BCM_PATCHRAM to work.
Relevant details from /sys/kernel/debug/usb/devices for my device:
T: Bus=03 Lev=02 Prnt=02 Port=03 Cnt=02 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e031 Rev= 1.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
S: SerialNumber=3859F9CD2AEE
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
The firmware was extracted from a Windows 7 32-bit installation
and converted from 'hex' to 'hcd' for use in Linux.
The firmware is named "BCM20702A0_001.001.024.0156.0204.hex"
and is located in "%SYSTEMROOT%\system32\drivers\"
(md5 d126e6c4e0e669d76c38cf9377f76b7f)
(sha1 145d1850b2785a953233b409e7ff77786927c7d2)
The firmware file is also available as a download at
http://support.ts.fujitsu.com/Download/
contained in "FTS_WIDCOMMBluetoothSoftware_6309000_1072149.zip"
Search for the file Win32/bcbtums-win7x86-brcm.inf in the archive,
look for the vendor and product ID of your adapter, see the section
'devices' in that file to find out what device name it uses. See
the device entry in the inf file (in my case it was 'RAMUSBE031')
to find out which hex file you need to convert to hcd for upload
'hcd' file should be placed at "brcm/BCM20702A0-0489-e031.hcd"
inside the firmware directory (e.g. "/lib/firmware")
Signed-off-by: Heinrich Siebmanns <harv@gmx.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-12-03 19:40:44 +01:00
Dmitry Tunin
3bb30a7cdf
Bluetooth: ath3k: Add support of MCI 13d3:3408 bt device
...
Add support for Bluetooth MCI WB335 (AR9565) Wi-Fi+bt module. This
Bluetooth module requires loading patch and sysconfig by ath3k driver.
T: Bus=01 Lev=02 Prnt=03 Port=00 Cnt=01 Dev#= 20 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3408 Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org
2014-11-26 19:46:24 +02:00
Fabio K
a86c02ea38
Bluetooth: Add support for Broadcom BCM20702A1 variant
...
This variant requires the flag BTUSB_BCM_PATCHRAM to work.
Relevant details from /sys/kernel/debug/usb/devices:
T: Bus=01 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3404 Rev= 1.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
S: SerialNumber=240A646F1XXX
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
The firmware was extracted from a Windows 8.1 64-bit installation
and converted from 'hex' to 'hcd' for use in Linux.
Under Windows it also identifies itself as BCM20702A0,
but the firmware is named "BCM20702A1_001.002.014.1315.1356.hex"
and is located in "%SYSTEMROOT%\system32\drivers\"
(md5 67cf6bfdae61c4bb819a66da984f7913)
(sha1 5f74cc6a9a3bf19ee0f8c3d01e4be34c609b188f)
The same firmware file is also available as a download at
http://www.asrock.com/mb/Intel/Z87E-ITX/?cat=Download&os=All
marked as "Bluetooth driver ver:12.0.0.7820"
'hcd' file should be placed at "brcm/BCM20702A0-13d3-3404.hcd"
inside the firmware directory (e.g. "/lib/firmware")
Signed-off-by: Fabio K <healthkit@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-11-18 08:32:14 +01:00
Marcel Holtmann
2cbd3f5ccd
Bluetooth: btusb: Add internal callback for USB bulk rx data
...
Some vendors require special handling of the rx data from the USB
bulk endpoints. For that case provide an internal callback that
can overwrite it with a custom receive function.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2014-11-03 10:13:42 +02:00
Marcel Holtmann
27c3fbe00b
Bluetooth: Set HCI_QUIRK_STRICT_DUPLICATE_FILTER for Broadcom devices
...
The Bluetooth controllers from Broadcom use a strict scanning filter
policy that filters based on Bluetooth device addresses and not on
RSSI. So tell the core about this.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2014-11-03 10:13:41 +02:00
Anantha Krishnan
4b552bc9ed
Bluetooth: Add support for Acer [0489:e078]
...
Add support for the QCA6174 chip.
T: Bus=06 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e078 Rev=00.01
C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: Anantha Krishnan <ananthk@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-10-25 07:56:22 +02:00
Amitkumar Karwar
6a57dba9f0
Bluetooth: btusb: remove redundant lock variable
...
This variable is nowhere used in the code.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-09-30 14:13:29 +02:00
Marcel Holtmann
803b58367f
Bluetooth: btusb: Implement driver internal packet reassembly
...
When receiving USB interrupt, bulk or isochronous packet, they normally
come in fragments. So far the driver just handed each fragment off to
the hci_recv_fragment function of the Bluetooth core. That function is
however so specific that is does not belong in the core. This patch
implements the same reassembly logic in the driver.
In addition this fixes a long standing bug where multiple complete
packets are received within a single USB packet.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2014-09-16 21:33:15 +03:00
Marcel Holtmann
1ffa4ad042
Bluetooth: btusb: Split fragement receiption into separate functions
...
The actual packet reassembly should be done inside the driver. To allow
this to happen cleanly in future patches, split the fragment reception
into its own functions.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2014-09-16 06:41:17 +03:00
Marcel Holtmann
89e7533d0a
Bluetooth: btusb: Fix old coding style issues
...
The btusb driver has been around for a while now and it is time to
bring its coding style in sync with what has been done for the
Bluetooth subsystem and other drivers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2014-09-16 06:41:12 +03:00
Marcel Holtmann
047b2ec8d3
Bluetooth: btusb: Separate TX URB allocation and submission
...
The complete TX URB handling is done via a switch statement in the
btusb_send_frame function. To allow for more clear separation between
control, bulk and isoc URBs, split them into allocation and submission.
Previously the inc_tx function has been used for tracking in-flight
URB for HCI commands and ACL data packets. Convert that into a common
function that either submits the URB or queues it when needed.
This provides the flexibility to allow vendor specific hdev->send_frame
callbacks without having to duplicate the whole URB handling logic.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2014-09-14 18:35:28 +02:00
Johan Hedberg
e9753eff1b
Bluetooth: btusb: Use GFP_KERNEL in btusb_send_frame()
...
All hdev->send() calls are these days done through a work queue. For the
btusb driver this means the btusb_send_frame() function. Because of this
we can safely use GFP_KERNEL for all memory allocations in this code
path.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-09-14 08:56:46 +02:00
Champion Chen
85560c4a82
Bluetooth: Fix issue with USB suspend in btusb driver
...
Suspend could fail for some platforms because
btusb_suspend==> btusb_stop_traffic ==> usb_kill_anchored_urbs.
When btusb_bulk_complete returns before system suspend and resubmits
an URB, the system cannot enter suspend state.
Signed-off-by: Champion Chen <champion_chen@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
2014-09-09 03:23:40 +02:00
Vincent Zwanenburg
89d2975fa0
Add a new PID/VID 0227/0930 for AR3012.
...
usb devices info:
T: Bus=01 Lev=02 Prnt=05 Port=00 Cnt=01 Dev#= 20 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0930 ProdID=0227 Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Vincent Zwanenburg <vincentz@topmail.ie>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-08-14 08:49:20 +02:00
Marcel Holtmann
c2aef6e8cb
Bluetooth: Add support for Broadcom device of Asus Z97-DELUXE motherboard
...
The Asus Z97-DELUXE motherboard contains a Broadcom based Bluetooth
controller on the USB bus. However vendor and product ID are listed
as ASUSTek Computer.
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0b05 ProdID=17cf Rev= 1.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
S: SerialNumber=54271E910064
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Reported-by: Jerome Leclanche <jerome@leclan.ch>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2014-07-21 15:07:08 +03:00
Amitkumar Karwar
ae8df494e9
Bluetooth: add public address configuration for Marvell USB devices
...
Implemented .set_bdaddr handler provided by bluetooth stack for
Marvell devices for public address configuration.
A reboot restores the bdaddr to its original address.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-07-19 02:33:21 +02:00
Anantha Krishnan
fa2f1394fe
Bluetooth: Add support for Acer [13D3:3432]
...
Add support for the QCA6174 chip.
T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 30 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3432 Rev=00.02
C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: Anantha Krishnan <ananthk@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-07-08 17:20:02 +02:00
Marcel Holtmann
4f64fa807a
Bluetooth: Use BTUSB_BROKEN_ISOC flag for CSR USB sniffer devices
...
Instead of setting data->isoc manually, use BTUSB_BROKEN_ISOC to
indicate that isochronous endpoints are not needed for CSR USB
sniffer devices.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2014-07-07 08:45:27 +03:00
Marcel Holtmann
d92f2df056
Bluetooth: Ignore isochronous endpoints for Intel USB bootloader
...
The isochronous endpoints are not valid when the Intel Bluetooth
controller boots up in bootloader mode. So just mark these endpoints
as broken and then they will not be configured.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2014-07-06 16:18:51 +03:00
Marcel Holtmann
3a5ef20c97
Bluetooth: Handle Intel USB bootloader with buggy interrupt
...
The interrupt interface for the Intel USB bootloader devices is only
enabled after receiving SetInterface(0, AltSetting=0). When this USB
command is not send, then no HCI events will be received.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2014-07-06 16:16:05 +03:00
Marcel Holtmann
01bb75ed26
Bluetooth: Remove module parameters for ignoring USB devices
...
The module parameters to ignore devices based on USB VID/PID are not
needed at all. So just remove them.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2014-07-06 15:48:54 +03:00
Marcel Holtmann
40df783d1e
Bluetooth: Add support for Intel bootloader devices
...
Intel Bluetooth devices that boot up in bootloader mode can not
be used as generic HCI devices, but their HCI transport is still
valuable and so bring that up as raw-only devices.
T: Bus=02 Lev=02 Prnt=03 Port=00 Cnt=01 Dev#= 14 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=ff(vend.) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=8087 ProdID=0a5a Rev= 0.00
S: Manufacturer=Intel(R) Corporation
S: Product=Intel(R) Wilkins Peak 2x2
S: SerialNumber=001122334455 WP_A0
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2014-07-06 14:46:56 +03:00
Marcel Holtmann
849e5086b9
Bluetooth: Set HCI_QUIRK_INVALID_BADDR for BCM20702A0 default address
...
When the Broadcom USB controller has a default address, then set the quirk
so the Bluetooth core knows that controller configuration is required.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2014-07-04 18:09:35 +03:00
Marcel Holtmann
4739b5b185
Bluetooth: Set HCI_QUIRK_INVALID_BADDR for Intel USB default address
...
When the Intel USB controller has a default address, then set the quirk
so the Bluetooth core knows that controller configuration is required.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2014-07-04 18:09:34 +03:00
Marcel Holtmann
c8abb73fb8
Bluetooth: Check for default address of Broadcom BCM20702A0 controllers
...
The Broadcom BCM20702A0 USB controllers might come with the default
address 00:20:70:02:A0:00 when booting up. If this happens, then warn
about such address being used.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2014-07-03 17:42:56 +02:00
Marcel Holtmann
40cb098415
Bluetooth: Check for default address of Intel USB controllers
...
Some Intel Bluetooth controllers come with a default address. If this
address is found, print an error to warn the user about it.
The controller is fully operational, but the danger of duplicate
Bluetooth addresses might causes issues. At least with a clear
error it becomes easier to debug these cases.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2014-07-03 17:42:56 +02:00
Marcel Holtmann
cb8d65973b
Bluetooth: Add public address configration for Intel USB devices
...
For the Intel based USB devices add support for configuration of
the public device address.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2014-07-03 17:42:56 +02:00
Marcel Holtmann
abbaf50e3b
Bluetooth: Add public address configration for Broadcom USB devices
...
For the Broadcom based USB devices add support for configuration of
the public device address.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2014-07-03 17:42:55 +02:00
Marcel Holtmann
a2b23bacb3
Revert "Bluetooth: Add a new PID/VID 0cf3/e005 for AR3012."
...
This reverts commit ca58e594da0a3658cccdstable@vger.kernel.org # 3.15.x
2014-06-20 12:45:35 +02:00
John W. Linville
a5eb1aeb25
Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
...
Conflicts:
drivers/bluetooth/btusb.c
2014-05-29 13:03:47 -04:00
Petri Gynther
10d4c6736e
Bluetooth: btusb: Add Broadcom patch RAM support
...
After hardware reset, some BCM Bluetooth adapters obtain their initial firmware
from OTPROM chip. Once this initial firmware is running, the firmware can be
further upgraded over HCI interface with .hcd files provided by Broadcom. This
is also known as "patch RAM" support. This change implements that.
If the .hcd file is not found in /lib/firmware, BCM Bluetooth adapter continues
to operate with the initial firmware. Sample kernel log:
hotplug: sys=firmware act=add fw=brcm/BCM20702A0-0a5c-22be.hcd dev=...
Bluetooth: hci0: BCM: patch brcm/BCM20702A0-0a5c-22be.hcd not found
If the .hcd file is found, btusb driver pushes it to the BCM Bluetooth adapter and
it starts using the new firmware. Sample kernel log:
hotplug: sys=firmware act=add fw=brcm/BCM20702A0-0a5c-22be.hcd dev=...
Bluetooth: hci0: BCM: patching hci_ver=06 hci_rev=1000 lmp_ver=06 lmp_subver=220e
Bluetooth: hci0: BCM: firmware hci_ver=06 hci_rev=1389 lmp_ver=06 lmp_subver=220e
Above, we can see that hci_rev goes from 1000 to 1389 as a result of the upgrade.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-05-08 16:12:57 -07:00
Mohammed Habibulla
1fb4e09a7e
Bluetooth: Add support for Lite-on [04ca:3007]
...
Add support for the AR9462 chip
T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=03 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=04ca ProdID=3007 Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Mohammed Habibulla <moch@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2014-04-25 09:47:16 +03:00
Marcel Holtmann
3c49aa852e
Revert "Bluetooth: Enable autosuspend for Intel Bluetooth device"
...
This reverts commit d2bee8fb6estable@vger.kernel.org
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2014-04-25 09:47:15 +03:00
Peng Chen
ca58e594da
Bluetooth: Add a new PID/VID 0cf3/e005 for AR3012.
...
usb devices info:
T: Bus=06 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 13 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0cf3 ProdID=e005 Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Peng Chen <pengchen@qca.qualcomm.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2014-03-05 20:52:17 +02:00
Andy Shevchenko
a735f9e224
Bluetooth: append new supported device to the list [0b05:17d0]
...
The device found on Asus Z87 Expert motherboard requires firmware to work
correctly.
T: Bus=03 Lev=01 Prnt=01 Port=03 Cnt=02 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0b05 ProdID=17d0 Rev=00.02
C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-02-18 09:54:20 -08:00
Andy Shevchenko
0b8800623d
Bluetooth: sort the list of IDs in the source code
...
This will help to manage table of supported IDs.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-02-18 09:54:20 -08:00
Jurgen Kramer
9113bfd82d
Bluetooth: btusb: Add IMC Networks (Broadcom based)
...
Add support for IMC Networks (Broadcom based) to btusb driver.
Below the output of /sys/kernel/debug/usb/devices for this device:
T: Bus=01 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3404 Rev= 1.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
S: SerialNumber=240A649F8246
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Signed-off-by: Jurgen Kramer <gtmkramer@xs4all.nl>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-02-15 11:51:03 -08:00
Oliver Neukum
1e56f1eb2b
Bluetooth: Add firmware update for Atheros 0cf3:311f
...
The device is not functional without firmware.
The device without firmware:
T: Bus=02 Lev=02 Prnt=02 Port=05 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0cf3 ProdID=311f Rev=00.01
C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
The device with firmware:
T: Bus=02 Lev=02 Prnt=02 Port=05 Cnt=01 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0cf3 ProdID=3007 Rev=00.01
C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-02-13 09:51:36 +02:00
Oliver Neukum
b131237ca3
Bluetooth: Enable Atheros 0cf3:311e for firmware upload
...
The device will bind to btusb without firmware, but with the original
buggy firmware device discovery does not work. No devices are detected.
Device descriptor without firmware:
T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0cf3 ProdID=311e Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
with firmware:
T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0cf3 ProdID=311e Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-02-13 09:51:36 +02:00
John W. Linville
300e5fd160
Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
2014-01-08 13:44:29 -05:00
John W. Linville
9d1cd503c7
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
2014-01-06 14:08:41 -05:00
Marcel Holtmann
81cac64ba2
Bluetooth: Deal with USB devices that are faking CSR vendor
...
There exists a set of Bluetooth USB devices that show up on the USB
bus as 0a12:0001 and identify themselves as devices from CSR. However
they are not. When sending Read Local Version command they now have
a split personality and say they are from Broadcom.
< HCI Command: Read Local Version Information (0x04|0x0001) plen 0
> HCI Event: Command Complete (0x0e) plen 12
Read Local Version Information (0x04|0x0001) ncmd 1
status 0x00
HCI Version: 2.0 (0x3) HCI Revision: 0x3000
LMP Version: 2.0 (0x3) LMP Subversion: 0x420b
Manufacturer: Broadcom Corporation (15)
The assumption is that they are neither CSR nor Broadcom based devices
and that they are designed and manufactured by someone else.
For the most parts they follow the Bluetooth HCI specification and
can be used as standard Bluetooth devices. However they have the
minor problem that the Delete Stored Link Key command is not working
as it should.
During the Bluetooth controller setup, this command is needed if
stored link keys are supported. For these devices it has to be
assumed that this is broken and so just set a quirk to clearly
indicate the behavior. After that the setup can just proceed.
Now the trick part is to detect these faulty devices since we do
not want to punish all CSR and all Broadcom devices. The original
devices do actually work according to the specification.
What is known so far is that these broken devices set the USB bcdDevice
revision information to 1.0 or less.
T: Bus=02 Lev=01 Prnt=01 Port=08 Cnt=03 Dev#= 9 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a12 ProdID=0001 Rev= 1.00
S: Manufacturer=Bluetooth v2.0
S: Product=Bluetooth V2.0 Dongle
T: Bus=05 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a12 ProdID=0001 Rev= 0.07
In case of CSR devices, the bcdDevice revision contains the firmware
build ID and that is normally a higher value. If the bcdDevice revision
is 1.0 or less, then an extra setup stage is checking if Read Local
Version returns CSR manufacturer information. If not then it will be
assumed that this is a broken device and the Delete Stored Link Key
command will be marked as broken.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2014-01-04 20:11:07 +02:00
Marco Piazza
bd0976dd33
Bluetooth: Add support for Toshiba Bluetooth device [0930:0220]
...
This patch adds support for new Toshiba Bluetooth device.
T: Bus=05 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0930 ProdID=0220 Rev=00.02
C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: Marco Piazza <mpiazza@gmail.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-12-04 11:11:49 -02:00
Tedd Ho-Jeong An
d2bee8fb6e
Bluetooth: Enable autosuspend for Intel Bluetooth device
...
This patch enables autosuspend for Intel Bluetooth device.
After btusb is loaded for Intel Bluetooth device, the power/control
attribute contains "on" value by default which disables the autosuspend.
Based on the USB PM document(Documentation/usb/power-management.txt),
kernel disabled the autosuspend for all devices other than hub by default.
"The USB specification states that all USB devices must support power
management. Nevertheless, the sad fact is that many devices do not
support it very well. You can suspend them all right, but when you
try to resume them they disconnect themselves from the USB bus or
they stop working entirely. This seems to be especially prevalent
among printers and scanners, but plenty of other types of device have
the same deficiency.
For this reason, by default the kernel disables autosuspend (the
power/control attribute is initialized to "on") for all devices other
than hubs. Hubs, at least, appear to be reasonably well-behaved in
this regard."
This document also described how the driver can enables the autosuspend
by using an USB api.
"Drivers can enable autosuspend for their devices by calling
usb_enable_autosuspend(struct usb_device *udev);
in their probe() routine, if they know that the device is capable of
suspending and resuming correctly. This is exactly equivalent to
writing "auto" to the device's power/control attribute."
For Intel Bluetooth device, the autosuspend needs to be enabled so the
device can transit to LPM(Low Power Mode) and ULPM(Ultra LPM) states after
receiving suspend message from the host.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2013-12-04 11:09:05 -02:00
Tedd Ho-Jeong An
ef4e5e4a75
Bluetooth: Add support for Intel Bluetooth device [8087:0a2a]
...
This patch adds support for new Intel Bluetooth device.
T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=8087 ProdID=0a2a Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2013-12-04 11:09:04 -02:00
Sujith Manoharan
35580d223b
Bluetooth: ath3k: Add support for a new AR3012 device
...
T: Bus=02 Lev=01 Prnt=01 Port=04 Cnt=01 Dev#= 9 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e05f Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Reported-by: Joshua Richenhagen <richenhagen@gmail.com>
Signed-off-by: Sujith Manoharan <sujith@msujith.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-12-04 11:09:04 -02:00
Sujith Manoharan
bd0fca1b2b
Bluetooth: ath3k: Add support for another AR3012 card
...
T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=04ca ProdID=300b Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Reported-by: Face <falazemi@gmail.com>
Signed-off-by: Sujith Manoharan <sujith@msujith.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2013-12-04 11:09:04 -02:00
John W. Linville
6b732323c1
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
2013-11-05 15:58:21 -05:00
Marcel Holtmann
54265202f1
Bluetooth: Declare btusb_table[] and blacklist_table[] as const
...
The btusb_table[] and blacklist_table[] USB device tables can be
declared as const.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-11 17:05:18 +02:00
Marcel Holtmann
7bd8f09f69
Bluetooth: Add hdev parameter to hdev->send driver callback
...
Instead of masking hdev inside the skb->dev parameter, hand it
directly to the driver as a parameter to hdev->send. This makes
the driver interface more clear and simpler.
This patch fixes all drivers to accept and handle the new parameter
of hdev->send callback. Special care has been taken for bpa10x
and btusb drivers that require having skb->dev set to hdev for
the URB transmit complete handlers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-11 15:28:03 +02:00
Marcel Holtmann
014f7bc787
Bluetooth: Use hci_conn_num() instead of direct connection hash access
...
When changing the alternate setting for the ISOC endpoints, use the
hci_conn_num() helper function to count currently established SCO
and eSCO connections and store the the value. This avoids direct
access to the connection hash.
In addition use the stored value instead accessing the connection
hash over and over again.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-10 22:08:02 +02:00
Hans de Goede
b1a8014471
Bluetooth: revert: "Bluetooth: Add missing reset_resume dev_pm_ops"
...
Many btusb devices have 2 modes, a hid mode and a bluetooth hci mode. These
devices default to hid mode for BIOS use. This means that after having been
reset they will revert to HID mode, and are no longer usable as a HCI.
Therefor it is a very bad idea to just blindly make reset_resume point to
the regular resume handler. Note that the btusb driver has no clue how to
switch these devices from hid to hci mode, this is done in userspace through
udev rules, so the proper way to deal with this is to not have a reset-resume
handler and instead let the usb-system re-enumerate the device, and re-run
the udev rules.
I must also note, that the commit message for the commit causing this
problem has a very weak motivation for the change:
"Add missing reset_resume dev_pm_ops. Missing reset_resume results in the
following message after power management device test. This change sets
reset_resume to btusb_resume().
[ 2506.936134] btusb 1-1.5:1.0: no reset_resume for driver btusb?
[ 2506.936137] btusb 1-1.5:1.1: no reset_resume for driver btusb?"
Making a change solely to silence a warning while also changing important
behavior (normal resume handling versus re-enumeration) requires a commit
message with a proper explanation why it is safe to do so, which clearly lacks
here, and unsurprisingly it turns out to not be safe to make this change.
Reverting the commit in question fixes bt no longer working on my Dell
E6430 after a suspend/resume, and I believe it likely also fixes the
following bugs:
https://bugzilla.redhat.com/show_bug.cgi?id=988481
https://bugzilla.redhat.com/show_bug.cgi?id=1010649
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1213239
This reverts commit 502f769662stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-10-02 16:01:49 -03:00
Ken O'Brien
5bcecf3253
Bluetooth: btusb: Add support for Belkin F8065bf
...
Add generic rule on encountering Belkin bluetooth usb device F8065bf.
Relevant section from /sys/kernel/debug/usb/devices:
T: Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=050d ProdID=065a Rev= 1.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
S: SerialNumber=0002723E2D29
C:* #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
Signed-off-by: Ken O'Brien <kernel@kenobrien.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-09-23 17:44:25 -03:00
Raphael Kubo da Costa
38a172bef8
Bluetooth: Add support for BCM20702A0 [0b05, 17cb]
...
Yet another vendor specific ID for this chipset; this one for the ASUS
USB-BT400 Bluetooth 4.0 adapter.
T: Bus=03 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#= 6 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0b05 ProdID=17cb Rev=01.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
S: SerialNumber=000272C64400
C: #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Cc: stable@vger.kernel.org
Signed-off-by: Raphael Kubo da Costa <rakuco@FreeBSD.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-09-16 14:36:56 -03:00
Peng Chen
0a3658cccd
Bluetooth: Add a new PID/VID 0cf3/e005 for AR3012.
...
usb device info:
T: Bus=06 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 15 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0cf3 ProdID=e005 Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Peng Chen <pengchen@qca.qualcomm.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-09-16 14:36:55 -03:00
John W. Linville
704278ccb5
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
...
Conflicts:
net/bluetooth/hci_core.c
2013-07-31 15:11:50 -04:00
AceLan Kao
1d5b569ef8
Bluetooth: Add support for Atheros [0cf3:e003]
...
Add support for the AR9462 chip
T: Bus=02 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0cf3 ProdID=e003 Rev=00.02
C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-07-25 19:52:37 +01:00
AceLan Kao
1ebd0b21ab
Bluetooth: Add support for Atheros [0cf3:3121]
...
Add support for the AR3012 chip.
T: Bus=03 Lev=01 Prnt=01 Port=06 Cnt=01 Dev#= 6 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0cf3 ProdID=3121 Rev=00.02
C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-07-25 19:52:35 +01:00
Sujith Manoharan
5b77a1f3d7
Bluetooth: ath3k: Add support for ID 0x13d3/0x3402
...
T: Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 5 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3402 Rev= 0.02
S: Manufacturer=Atheros Communications
S: Product=Bluetooth USB Host Controller
S: SerialNumber=Alaska Day 2006
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=59701
Signed-off-by: Sujith Manoharan <sujith@msujith.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-07-25 19:52:34 +01:00
Adam Lee
d9c78e9738
Bluetooth: fix wrong use of PTR_ERR() in btusb
...
PTR_ERR() returns a signed long type value which is limited by IS_ERR(),
it must be a negative number whose range is [-MAX_ERRNO, 0).
The bug here returns negative numbers as error codes, then check it by
"if (ret < 0)", but -PTR_ERR() is actually positive. The wrong use here
leads to failure as below, even panic.
[ 12.958920] Bluetooth: hci0 command 0xfc8e tx timeout
[ 14.961765] Bluetooth: hci0 command 0xfc8e tx timeout
[ 16.964688] Bluetooth: hci0 command 0xfc8e tx timeout
[ 20.954501] Bluetooth: hci0 sending Intel patch command (0xfc8e) failed (-110)
[ 22.957358] Bluetooth: hci0 command 0xfc8e tx timeout
[ 30.948922] Bluetooth: hci0 sending Intel patch command (0xfc8e) failed (-110)
[ 32.951780] Bluetooth: hci0 command 0xfc8e tx timeout
[ 40.943359] Bluetooth: hci0 sending Intel patch command (0xfc8e) failed (-110)
[ 42.946219] Bluetooth: hci0 command 0xfc8e tx timeout
[ 50.937812] Bluetooth: hci0 sending Intel patch command (0xfc8e) failed (-110)
[ 52.940670] Bluetooth: hci0 command 0xfc8e tx timeout
[ 60.932236] Bluetooth: hci0 sending Intel patch command (0xfc8e) failed (-110)
[ 62.935092] Bluetooth: hci0 command 0xfc8e tx timeout
[ 70.926688] Bluetooth: hci0 sending Intel patch command (0xfc8e) failed (-110)
[ 72.929545] Bluetooth: hci0 command 0xfc8e tx timeout
[ 80.921111] Bluetooth: hci0 sending Intel patch command (0xfc8e) failed (-110)
[ 82.923969] Bluetooth: hci0 command 0xfc2f tx timeout
[ 90.915542] Bluetooth: hci0 sending Intel patch command (0xfc2f) failed (-110)
[ 92.918406] Bluetooth: hci0 command 0xfc11 tx timeout
[ 100.909955] Bluetooth: hci0 sending Intel patch command (0xfc11) failed (-110)
[ 102.912858] Bluetooth: hci0 command 0xfc60 tx timeout
[ 110.904394] Bluetooth: hci0 sending Intel patch command (0xfc60) failed (-110)
[ 112.907293] Bluetooth: hci0 command 0xfc11 tx timeout
[ 120.898831] Bluetooth: hci0 exiting Intel manufacturer mode failed (-110)
[ 120.904757] bluetoothd[1030]: segfault at 4 ip 00007f8b2eb55236 sp 00007fff53ff6920 error 4 in bluetoothd[7f8b2eaff000+cb000]
Signed-off-by: Adam Lee <adam.lee@canonical.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-07-25 19:52:33 +01:00
Thomas Loo
84eb2ae180
Bluetooth: ath3k: Add support for Fujitsu Lifebook UH5x2 [04c5:1330]
...
The Fujitsu Lifebook UH552/UH572 ships with a Qualcomm AR9462/AR3012
WLAN/BT-Combo card.
Add device ID to the ath3k driver to enable the bluetooth side of things.
Patch against v3.10.
T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=04c5 ProdID=1330 Rev=00.02
C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: Thomas Loo <tloo@saltstorm.net>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-07-25 19:52:31 +01:00
Shuah Khan
502f769662
Bluetooth: Add missing reset_resume dev_pm_ops
...
Add missing reset_resume dev_pm_ops. Missing reset_resume results in the
following message after power management device test. This change sets
reset_resume to btusb_resume().
[ 2506.936134] btusb 1-1.5:1.0: no reset_resume for driver btusb?
[ 2506.936137] btusb 1-1.5:1.1: no reset_resume for driver btusb?
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-06-23 00:23:53 +01:00
Cho, Yu-Chen
178c059e76
Bluetooth: Add support for Mediatek Bluetooth device [0e8d:763f]
...
This patch adds support for Mediatek Bluetooth device
T: Bus=02 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.01 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0e8d ProdID=763f Rev= 1.00
S: Manufacturer=MediaTek
S: Product=BT
S: SerialNumber=1.0
C:* #Ifs= 2 Cfg#= 1 Atr=a0 MxPwr=450mA
A: FirstIf#= 0 IfCount= 2 Cls=ff(vend.) Sub=ff Prot=ff
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
Signed-off-by: Cho, Yu-Chen <acho@suse.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-13 13:32:28 -04:00
Tedd Ho-Jeong An
dffd30ee96
Bluetooth: Add support for Intel Bluetooth device [8087:07dc]
...
This patch adds support for Intel Bluetooth device by adding
btusb_setup_intel() routine that update the device with ROM patch.
T: Bus=02 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=8087 ProdID=07dc Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-04-23 20:27:48 -03:00
Marcel Holtmann
9f8f962c85
Bluetooth: Use separate function for BCM92035 vendor setup
...
Trying to squeeze every single vendor setup routine into the same function
and have it assigned all the time is actually a bad idea. Especially since
the core can handle the absence of a setup routine perfectly fine.
To make this a lot simpler for future additions of vendor setup code,
split the BCM92035 setup into its own function and only assign it when
this specific device has been detected.
Doing it like this has the nice side benefit that we do not have to keep
a copy of the driver_info around.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-04-11 16:34:10 -03:00
Marcel Holtmann
9360099764
Bluetooth: Convert BCM92035 support to driver setup callback
...
With the early init stage during setup, this quirk can be simplified
and kept fully inside the driver.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-04-04 19:28:10 +03:00
Noguchi Kazutosi
0fc110f4e4
Bluetooth: Add support for Foxconn/Hon Hai [0489:e04d]
...
Add support for the AR3012 chip.
T: Bus=01 Lev=02 Prnt=02 Port=05 Cnt=03 Dev#= 21 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e04d Rev=00.02
S: Manufacturer=Atheros Communications
S: Product=Bluetooth USB Host Controller
S: SerialNumber=Alaska Day 2006
C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: Noguchi Kazutosi <linux@scaltinof.net>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-04-04 11:12:32 +03:00
Ming Lei
ebaf5795ef
Bluetooth: Add support for Dell[QCA 0cf3:817a]
...
Add support for the AR9462 chip
T: Bus=03 Lev=01 Prnt=01 Port=08 Cnt=01 Dev#= 5 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0cf3 ProdID=817a Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Cc: <stable@vger.kernel.org>
Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-03-18 14:14:37 -03:00
Ming Lei
d66629c132
Bluetooth: Add support for Dell[QCA 0cf3:0036]
...
Add support for the AR9462 chip
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0cf3 ProdID=0036 Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Cc: <stable@vger.kernel.org>
Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-03-15 14:11:32 -03:00
Sunguk Lee
94a32d10f4
Bluetooth: Device 0cf3:3008 should map AR 3012
...
T: Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0cf3 ProdID=3008 Rev= 0.01
S: Manufacturer=Atheros Communications
S: Product=Bluetooth USB Host Controller
S: SerialNumber=Alaska Day 2006
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Sunguk Lee <d3m3vilurr@gmail.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-03-11 18:04:54 -03:00
Josh Boyer
3f63c340a7
Bluetooth: Add support for atheros 04ca:3004 device to ath3k
...
Yet another version of the atheros bluetooth chipset
T: Bus=01 Lev=02 Prnt=02 Port=03 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=04ca ProdID=3004 Rev=00.01
S: Manufacturer=Atheros Communications
S: Product=Bluetooth USB Host Controller
S: SerialNumber=Alaska Day 2006
C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
This resolves https://bugzilla.redhat.com/show_bug.cgi?id=844750
Reported-by: niktr@mail.ru
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-02-20 14:23:08 -03:00
Sergio Cambra
f4d6f7dce7
Bluetooth device 04ca:3008 should use ath3k
...
Output of /sys/kernel/debug/usb/devices
T: Bus=03 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 6 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=04ca ProdID=3008 Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Sergio Cambra <sergio@programatica.es>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-01-10 02:51:03 -02:00
AceLan Kao
2582d529c4
Bluetooth: Add support for Foxconn / Hon Hai [0489:e056]
...
Add support for the AR9462 chip
T: Bus=01 Lev=02 Prnt=02 Port=05 Cnt=01 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e056 Rev=00.01
C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-01-09 17:05:15 -02:00
AceLan Kao
3a61eda81e
Bluetooth: Add support for Foxconn / Hon Hai [0489:e04e]
...
Add support for the AR9462 chip
T: Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 5 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e04e Rev=00.02
C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-01-09 17:05:15 -02:00
Daniel Schaal
2c262b2a52
Bluetooth: Add support for GC-WB300D PCIe [04ca:3006] to ath3k.
...
T: Bus=02 Lev=02 Prnt=02 Port=06 Cnt=01 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=04ca ProdID=3006 Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Daniel Schaal <farbing@web.de>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-01-09 17:05:14 -02:00
AceLan Kao
eed307e290
Bluetooth: Add support for IMC Networks [13d3:3393]
...
Add support for the AR9462 chip
T: Bus=02 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3393 Rev=00.01
C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-01-09 17:05:14 -02:00
John W. Linville
d2ff5ee919
Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
2012-11-21 13:03:00 -05:00
Jeff Cook
1ee3ff6110
Bluetooth: Add support for BCM20702A0 [0b05, 17b5]
...
Vendor-specific ID for BCM20702A0.
Support for bluetooth over Asus Wi-Fi GO!, included with Asus P8Z77-V
Deluxe.
T: Bus=07 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0b05 ProdID=17b5 Rev=01.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
S: SerialNumber=94DBC98AC113
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Cc: stable@vger.kernel.org
Signed-off-by: Jeff Cook <jeff@deserettechnology.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-11-19 19:52:23 -02:00
Marcos Chaparro
acd9454433
Bluetooth: ath3k: Add support for VAIO VPCEH [0489:e027]
...
Added Atheros AR3011 internal bluetooth device found in Sony VAIO VPCEH to the
devices list.
Before this, the bluetooth module was identified as an Foxconn / Hai bluetooth
device [0489:e027], now it claims to be an AtherosAR3011 Bluetooth
[0cf3:3005].
T: Bus=01 Lev=02 Prnt=02 Port=04 Cnt=02 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e027 Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Marcos Chaparro <marcos@mrkindustries.com.ar>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-11-09 16:45:37 +01:00
John W. Linville
791ef39cd1
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
2012-09-24 14:39:16 -04:00
Jaroslav Resler
0c1abbd1aa
Bluetooth: Add support for BCM20702A0 [04ca, 2003]
...
Add another vendor specific ID for BCM20702A0.
output of usb-devices:
T: Bus=01 Lev=02 Prnt=02 Port=03 Cnt=02 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=04ca ProdID=2003 Rev= 1.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
S: SerialNumber=446D57861623
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Signed-off-by: Cho, Yu-Chen <acho@suse.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-09-18 22:27:31 -03:00
