The function return parameter is not used in mvneta_tx_done_gbe(),
where the function is called. This patch makes the function return
void.
Reviewed-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
mvneta_tx_done_gbe() return value and third parameter are no more
used. This patch changes the function prototype and removes a useless
variable where the function is called.
Reviewed-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
calling dma_map_single()/dma_unmap_single() is quite expensive compared
to copying a small packet. So let's copy short frames and keep the buffers
mapped. We set the limit to 256 bytes which seems to give good results both
on the XP-GP board and on the AX3/4.
The Rx small packet rate increased by 16.4% doing this, from 486kpps to
573kpps. It is worth noting that even the call to the function
dma_sync_single_range_for_cpu() is expensive (300 ns) although less
than dma_unmap_single(). Without it, the packet rate raises to 711kpps
(+24% more). Thus on systems where coherency from device to CPU is
guaranteed by a snoop control unit, this patch should provide even more
gains, and probably rx_copybreak could be increased.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of build_skb() to allocate frags on the RX path. When frag size
is lower than a page size, we can use netdev_alloc_frag(), and we fall back
to kmalloc() for larger sizes. The frag size is stored into the mvneta_port
struct. The alloc/free functions check the frag size to decide what alloc/
free method to use. MTU changes are safe because the MTU change function
stops the device and clears the queues before applying the change.
With this patch, I observed a reproducible 2% performance improvement on
HTTP-based benchmarks, and 5% on small packet RX rate.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the mvneta driver tries to prefetch the current Rx
descriptor during read. Tests have shown that prefetching the
next one instead increases general performance by about 1% on
HTTP traffic.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
At several places, we already know the value of the rx status but
we call functions which dereference the pointer again to get it
and don't need the descriptor for anything else. Simplify this
task by replacing the rx desc pointer by the status word itself.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make mvneta_rxq_fill() use mvneta_rx_refill() instead of using
duplicate code.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, mvneta_txq_bufs_free() calls mvneta_tx_done_policy() with
a non-null cause to retrieve the pointer to the next queue to process.
There are useless tests on the return queue number and on the pointer,
all of which are well defined within a known limited set. This code
path is fast, although not critical. Removing 3 tests here that the
compiler could not optimize (verified) is always desirable.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now the mvneta driver doesn't handle Tx IRQ, and relies on two
mechanisms to flush Tx descriptors : a flush at the end of mvneta_tx()
and a timer. If a burst of packets is emitted faster than the device
can send them, then the queue is stopped until next wake-up of the
timer 10ms later. This causes jerky output traffic with bursts and
pauses, making it difficult to reach line rate with very few streams.
A test on UDP traffic shows that it's not possible to go beyond 134
Mbps / 12 kpps of outgoing traffic with 1500-bytes IP packets. Routed
traffic tends to observe pauses as well if the traffic is bursty,
making it even burstier after the wake-up.
It seems that this feature was inherited from the original driver but
nothing there mentions any reason for not using the interrupt instead,
which the chip supports.
Thus, this patch enables Tx interrupts and removes the timer. It does
the two at once because it's not really possible to make the two
mechanisms coexist, so a split patch doesn't make sense.
First tests performed on a Mirabox (Armada 370) show that less CPU
seems to be used when sending traffic. One reason might be that we now
call the mvneta_tx_done_gbe() with a mask indicating which queues have
been done instead of looping over all of them.
The same UDP test above now happily reaches 987 Mbps / 87.7 kpps.
Single-stream TCP traffic can now more easily reach line rate. HTTP
transfers of 1 MB objects over a single connection went from 730 to
840 Mbps. It is even possible to go significantly higher (>900 Mbps)
by tweaking tcp_tso_win_divisor.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Arnaud Ebalard <arno@natisbad.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell has not published the chip's datasheet yet, so it's very hard
to find the relevant bits to manipulate to change the IRQ behaviour.
Fortunately, these bits are described in the proprietary LSP patch set
which is publicly available here :
http://www.plugcomputer.org/downloads/mirabox/
So let's put them back in the driver in order to reduce the burden of
current and future maintenance.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a queue timeout is reported, we can oops because of some
schedules while the caller is atomic, as shown below :
mvneta d0070000.ethernet eth0: tx timeout
BUG: scheduling while atomic: bash/1528/0x00000100
Modules linked in: slhttp_ethdiv(C) [last unloaded: slhttp_ethdiv]
CPU: 2 PID: 1528 Comm: bash Tainted: G WC 3.13.0-rc4-mvebu-nf #180
[<c0011bd9>] (unwind_backtrace+0x1/0x98) from [<c000f1ab>] (show_stack+0xb/0xc)
[<c000f1ab>] (show_stack+0xb/0xc) from [<c02ad323>] (dump_stack+0x4f/0x64)
[<c02ad323>] (dump_stack+0x4f/0x64) from [<c02abe67>] (__schedule_bug+0x37/0x4c)
[<c02abe67>] (__schedule_bug+0x37/0x4c) from [<c02ae261>] (__schedule+0x325/0x3ec)
[<c02ae261>] (__schedule+0x325/0x3ec) from [<c02adb97>] (schedule_timeout+0xb7/0x118)
[<c02adb97>] (schedule_timeout+0xb7/0x118) from [<c0020a67>] (msleep+0xf/0x14)
[<c0020a67>] (msleep+0xf/0x14) from [<c01dcbe5>] (mvneta_stop_dev+0x21/0x194)
[<c01dcbe5>] (mvneta_stop_dev+0x21/0x194) from [<c01dcfe9>] (mvneta_tx_timeout+0x19/0x24)
[<c01dcfe9>] (mvneta_tx_timeout+0x19/0x24) from [<c024afc7>] (dev_watchdog+0x18b/0x1c4)
[<c024afc7>] (dev_watchdog+0x18b/0x1c4) from [<c0020b53>] (call_timer_fn.isra.27+0x17/0x5c)
[<c0020b53>] (call_timer_fn.isra.27+0x17/0x5c) from [<c0020cad>] (run_timer_softirq+0x115/0x170)
[<c0020cad>] (run_timer_softirq+0x115/0x170) from [<c001ccb9>] (__do_softirq+0xbd/0x1a8)
[<c001ccb9>] (__do_softirq+0xbd/0x1a8) from [<c001cfad>] (irq_exit+0x61/0x98)
[<c001cfad>] (irq_exit+0x61/0x98) from [<c000d4bf>] (handle_IRQ+0x27/0x60)
[<c000d4bf>] (handle_IRQ+0x27/0x60) from [<c000843b>] (armada_370_xp_handle_irq+0x33/0xc8)
[<c000843b>] (armada_370_xp_handle_irq+0x33/0xc8) from [<c000fba9>] (__irq_usr+0x49/0x60)
Ben Hutchings attempted to propose a better fix consisting in using a
scheduled work for this, but while it fixed this panic, it caused other
random freezes and panics proving that the reset sequence in the driver
is unreliable and that additional fixes should be investigated.
When sending multiple streams over a link limited to 100 Mbps, Tx timeouts
happen from time to time, and the driver correctly recovers only when the
function is disabled.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stats writers are mvneta_rx() and mvneta_tx(). They don't lock anything
when they update the stats, and as a result, it randomly happens that
the stats freeze on SMP if two updates happen during stats retrieval.
This is very easily reproducible by starting two HTTP servers and binding
each of them to a different CPU, then consulting /proc/net/dev in loops
during transfers, the interface should immediately lock up. This issue
also randomly happens upon link state changes during transfers, because
the stats are collected in this situation, but it takes more attempts to
reproduce it.
The comments in netdevice.h suggest using per_cpu stats instead to get
rid of this issue.
This patch implements this. It merges both rx_stats and tx_stats into
a single "stats" member with a single syncp. Both mvneta_rx() and
mvneta_rx() now only update the a single CPU's counters.
In turn, mvneta_get_stats64() does the summing by iterating over all CPUs
to get their respective stats.
With this change, stats are still correct and no more lockup is encountered.
Note that this bug was present since the first import of the mvneta
driver. It might make sense to backport it to some stable trees. If
so, it depends on "d33dc73 net: mvneta: increase the 64-bit rx/tx stats
out of the hot path".
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Better count packets and bytes in the stack and on 32 bit then
accumulate them at the end for once. This saves two memory writes
and two memory barriers per packet. The incoming packet rate was
increased by 4.7% on the Openblocks AX3 thanks to this.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
This covers everything under drivers/net except for wireless, which
has been submitted separately.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On archs like S390 or um this driver cannot build nor work.
Make it depend on HAS_IOMEM to bypass build failures.
drivers/built-in.o: In function `orion_mdio_probe':
drivers/net/ethernet/marvell/mvmdio.c:228: undefined reference to `devm_ioremap'
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c
net/ipv6/ip6_tunnel.c
net/ipv6/ip6_vti.c
ipv6 tunnel statistic bug fixes conflicting with consolidation into
generic sw per-cpu net stats.
qlogic conflict between queue counting bug fix and the addition
of multiple MAC address support.
Signed-off-by: David S. Miller <davem@davemloft.net>
This version corrects the whitespace issue.
orion_mdio_wait_ready uses wait_event_timeout to wait for the
SMI interrupt to fire. wait_event_timeout waits for between
"timeout - 1" and "timeout" jiffies. In this case a 1ms timeout
when HZ is 1000 results in a wait of 0 to 1 jiffies, causing
premature timeouts.
This fix ensures a minimum timeout of 2 jiffies, ensuring
wait_event_timeout will always wait at least 1 jiffie.
Issue reported by Nicolas Schichan.
Tested-by: Nicolas Schichan <nschichan@freebox.fr>
Signed-off-by: Leigh Brown <leigh@solinno.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers should call skb_set_hash to set the hash and its type
in an skbuff.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using phydev, it should be phy_start/phy_stop'ed properly. This
driver doesn't do that, so add the corresponding calls to port_start/
stop respectively.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of open-coding a PHY reset through the MII BMCR register, use
phy_init_hw() which does this for us and ensures that PHY device fixups
are also applied. We also remove a call to ethernet_phy_reset() which is
now unncessary since phy_attach() calls phy_attach_direct() which in
turns calls phy_init_hw().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of open-coding a PHY reset through the MII BMCR register, use
phy_init_hw() which does that for us and will also make sure that PHY
fixups are applied if required. We also remove a call to phy_reset()
due to the following sequence of calls in the driver:
phy_scan()
-> phy_connect()
-> phy_connect_direct()
-> phy_attach_direct()
-> phy_init_hw()
and we only have a call to phy_init() after phy_scan().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge 'net' into 'net-next' to get the AF_PACKET bug fix that
Daniel's direct transmit changes depend upon.
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code unmaps the DMA mapping created for rx skb_buff's by
using the data_size as the the mapping size. This is wrong since the
correct size to specify should match the size used to create the mapping.
This commit removes the following DMA_API_DEBUG warning:
------------[ cut here ]------------
WARNING: at lib/dma-debug.c:887 check_unmap+0x3a8/0x860()
mvneta d0070000.ethernet: DMA-API: device driver frees DMA memory with different size [device address=0x000000002eb80000] [map size=1600 bytes] [unmap size=66 bytes]
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.10.21-01444-ga88ae13-dirty #92
[<c0013600>] (unwind_backtrace+0x0/0xf8) from [<c0010fb8>] (show_stack+0x10/0x14)
[<c0010fb8>] (show_stack+0x10/0x14) from [<c001afa0>] (warn_slowpath_common+0x48/0x68)
[<c001afa0>] (warn_slowpath_common+0x48/0x68) from [<c001b01c>] (warn_slowpath_fmt+0x30/0x40)
[<c001b01c>] (warn_slowpath_fmt+0x30/0x40) from [<c018d0fc>] (check_unmap+0x3a8/0x860)
[<c018d0fc>] (check_unmap+0x3a8/0x860) from [<c018d734>] (debug_dma_unmap_page+0x64/0x70)
[<c018d734>] (debug_dma_unmap_page+0x64/0x70) from [<c0233f78>] (mvneta_rx+0xec/0x468)
[<c0233f78>] (mvneta_rx+0xec/0x468) from [<c023436c>] (mvneta_poll+0x78/0x16c)
[<c023436c>] (mvneta_poll+0x78/0x16c) from [<c02db468>] (net_rx_action+0x94/0x160)
[<c02db468>] (net_rx_action+0x94/0x160) from [<c0021e68>] (__do_softirq+0xe8/0x1d0)
[<c0021e68>] (__do_softirq+0xe8/0x1d0) from [<c0021ff8>] (do_softirq+0x4c/0x58)
[<c0021ff8>] (do_softirq+0x4c/0x58) from [<c0022228>] (irq_exit+0x58/0x90)
[<c0022228>] (irq_exit+0x58/0x90) from [<c000e7c8>] (handle_IRQ+0x3c/0x94)
[<c000e7c8>] (handle_IRQ+0x3c/0x94) from [<c0008548>] (armada_370_xp_handle_irq+0x4c/0xb4)
[<c0008548>] (armada_370_xp_handle_irq+0x4c/0xb4) from [<c000dc20>] (__irq_svc+0x40/0x50)
Exception stack(0xc04f1f70 to 0xc04f1fb8)
1f60: c1fe46f8 00000000 00001d92 00001d92
1f80: c04f0000 c04f0000 c04f84a4 c03e081c c05220e7 00000001 c05220e7 c04f0000
1fa0: 00000000 c04f1fb8 c000eaf8 c004c048 60000113 ffffffff
[<c000dc20>] (__irq_svc+0x40/0x50) from [<c004c048>] (cpu_startup_entry+0x54/0x128)
[<c004c048>] (cpu_startup_entry+0x54/0x128) from [<c04c1a14>] (start_kernel+0x29c/0x2f0)
[<c04c1a14>] (start_kernel+0x29c/0x2f0) from [<00008074>] (0x8074)
---[ end trace d4955f6acd178110 ]---
Mapped at:
[<c018d600>] debug_dma_map_page+0x4c/0x11c
[<c0235d6c>] mvneta_setup_rxqs+0x398/0x598
[<c0236084>] mvneta_open+0x40/0x17c
[<c02dbbd4>] __dev_open+0x9c/0x100
[<c02dbe58>] __dev_change_flags+0x7c/0x134
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several files refer to an old address for the Free Software Foundation
in the file header comment. Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.
CC: Santosh Raspatur <santosh@chelsio.com>
CC: Dimitris Michailidis <dm@chelsio.com>
CC: Michael Chan <mchan@broadcom.com>
CC: Santiago Leon <santil@linux.vnet.ibm.com>
CC: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
CC: Olof Johansson <olof@lixom.net>
CC: Manish Chopra <manish.chopra@qlogic.com>
CC: Sony Chacko <sony.chacko@qlogic.com>
CC: Rajesh Borundia <rajesh.borundia@qlogic.com>
CC: Nicolas Pitre <nico@fluxnic.net>
CC: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Mostly these are fixes for fallout due to merge window changes, as
well as cures for problems that have been with us for a much longer
period of time"
1) Johannes Berg noticed two major deficiencies in our genetlink
registration. Some genetlink protocols we passing in constant
counts for their ops array rather than something like
ARRAY_SIZE(ops) or similar. Also, some genetlink protocols were
using fixed IDs for their multicast groups.
We have to retain these fixed IDs to keep existing userland tools
working, but reserve them so that other multicast groups used by
other protocols can not possibly conflict.
In dealing with these two problems, we actually now use less state
management for genetlink operations and multicast groups.
2) When configuring interface hardware timestamping, fix several
drivers that simply do not validate that the hwtstamp_config value
is one the driver actually supports. From Ben Hutchings.
3) Invalid memory references in mwifiex driver, from Amitkumar Karwar.
4) In dev_forward_skb(), set the skb->protocol in the right order
relative to skb_scrub_packet(). From Alexei Starovoitov.
5) Bridge erroneously fails to use the proper wrapper functions to make
calls to netdev_ops->ndo_vlan_rx_{add,kill}_vid. Fix from Toshiaki
Makita.
6) When detaching a bridge port, make sure to flush all VLAN IDs to
prevent them from leaking, also from Toshiaki Makita.
7) Put in a compromise for TCP Small Queues so that deep queued devices
that delay TX reclaim non-trivially don't have such a performance
decrease. One particularly problematic area is 802.11 AMPDU in
wireless. From Eric Dumazet.
8) Fix crashes in tcp_fastopen_cache_get(), we can see NULL socket dsts
here. Fix from Eric Dumzaet, reported by Dave Jones.
9) Fix use after free in ipv6 SIT driver, from Willem de Bruijn.
10) When computing mergeable buffer sizes, virtio-net fails to take the
virtio-net header into account. From Michael Dalton.
11) Fix seqlock deadlock in ip4_datagram_connect() wrt. statistic
bumping, this one has been with us for a while. From Eric Dumazet.
12) Fix NULL deref in the new TIPC fragmentation handling, from Erik
Hugne.
13) 6lowpan bit used for traffic classification was wrong, from Jukka
Rissanen.
14) macvlan has the same issue as normal vlans did wrt. propagating LRO
disabling down to the real device, fix it the same way. From Michal
Kubecek.
15) CPSW driver needs to soft reset all slaves during suspend, from
Daniel Mack.
16) Fix small frame pacing in FQ packet scheduler, from Eric Dumazet.
17) The xen-netfront RX buffer refill timer isn't properly scheduled on
partial RX allocation success, from Ma JieYue.
18) When ipv6 ping protocol support was added, the AF_INET6 protocol
initialization cleanup path on failure was borked a little. Fix
from Vlad Yasevich.
19) If a socket disconnects during a read/recvmsg/recvfrom/etc that
blocks we can do the wrong thing with the msg_name we write back to
userspace. From Hannes Frederic Sowa. There is another fix in the
works from Hannes which will prevent future problems of this nature.
20) Fix route leak in VTI tunnel transmit, from Fan Du.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (106 commits)
genetlink: make multicast groups const, prevent abuse
genetlink: pass family to functions using groups
genetlink: add and use genl_set_err()
genetlink: remove family pointer from genl_multicast_group
genetlink: remove genl_unregister_mc_group()
hsr: don't call genl_unregister_mc_group()
quota/genetlink: use proper genetlink multicast APIs
drop_monitor/genetlink: use proper genetlink multicast APIs
genetlink: only pass array to genl_register_family_with_ops()
tcp: don't update snd_nxt, when a socket is switched from repair mode
atm: idt77252: fix dev refcnt leak
xfrm: Release dst if this dst is improper for vti tunnel
netlink: fix documentation typo in netlink_set_err()
be2net: Delete secondary unicast MAC addresses during be_close
be2net: Fix unconditional enabling of Rx interface options
net, virtio_net: replace the magic value
ping: prevent NULL pointer dereference on write to msg_name
bnx2x: Prevent "timeout waiting for state X"
bnx2x: prevent CFC attention
bnx2x: Prevent panic during DMAE timeout
...
We assume that "mp->phy" can be NULL a couple lines before the
dereference.
Fixes: 1cce16d37d ('net: mv643xx_eth: Add missing phy_addr_set in DT mode')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull core locking changes from Ingo Molnar:
"The biggest changes:
- add lockdep support for seqcount/seqlocks structures, this
unearthed both bugs and required extra annotation.
- move the various kernel locking primitives to the new
kernel/locking/ directory"
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (21 commits)
block: Use u64_stats_init() to initialize seqcounts
locking/lockdep: Mark __lockdep_count_forward_deps() as static
lockdep/proc: Fix lock-time avg computation
locking/doc: Update references to kernel/mutex.c
ipv6: Fix possible ipv6 seqlock deadlock
cpuset: Fix potential deadlock w/ set_mems_allowed
seqcount: Add lockdep functionality to seqcount/seqlock structures
net: Explicitly initialize u64_stats_sync structures for lockdep
locking: Move the percpu-rwsem code to kernel/locking/
locking: Move the lglocks code to kernel/locking/
locking: Move the rwsem code to kernel/locking/
locking: Move the rtmutex code to kernel/locking/
locking: Move the semaphore core to kernel/locking/
locking: Move the spinlock code to kernel/locking/
locking: Move the lockdep code to kernel/locking/
locking: Move the mutex code to kernel/locking/
hung_task debugging: Add tracepoint to report the hang
x86/locking/kconfig: Update paravirt spinlock Kconfig description
lockstat: Report avg wait and hold times
lockdep, x86/alternatives: Drop ancient lockdep fixup message
...
In order to enable lockdep on seqcount/seqlock structures, we
must explicitly initialize any locks.
The u64_stats_sync structure, uses a seqcount, and thus we need
to introduce a u64_stats_init() function and use it to initialize
the structure.
This unfortunately adds a lot of fairly trivial initialization code
to a number of drivers. But the benefit of ensuring correctness makes
this worth while.
Because these changes are required for lockdep to be enabled, and the
changes are quite trivial, I've not yet split this patch out into 30-some
separate patches, as I figured it would be better to get the various
maintainers thoughts on how to best merge this change along with
the seqcount lockdep enablement.
Feedback would be appreciated!
Signed-off-by: John Stultz <john.stultz@linaro.org>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: James Morris <jmorris@namei.org>
Cc: Jesse Gross <jesse@nicira.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Mirko Lindner <mlindner@marvell.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Roger Luethi <rl@hellgate.ch>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Simon Horman <horms@verge.net.au>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Wensong Zhang <wensong@linux-vs.org>
Cc: netdev@vger.kernel.org
Link: http://lkml.kernel.org/r/1381186321-4906-2-git-send-email-john.stultz@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit cc9d4598 'net: mv643xx_eth: use of_phy_connect if phy_node
present' made the call to phy_scan optional, if the DT has a link to
the phy node.
However phy_scan has the side effect of calling phy_addr_set, which
writes the phy MDIO address to the ethernet controller. If phy_addr_set
is not called, and the bootloader has not set the correct address then
the driver will fail to function.
Tested on Kirkwood.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Checking if MAC address is valid using is_valid_ether_addr() is already done in
of_get_mac_address().
Signed-off-by: Luka Perkov <luka@openwrt.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
CC: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amend the documentation in the mvmdio driver to note the fact
that it is now used by both the mvneta and mv643xx_eth drivers.
Signed-off-by: Leigh Brown <leigh@solinno.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make only a single call to mutex_unlock in orion_mdio_write.
Signed-off-by: Leigh Brown <leigh@solinno.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace manual poll of MVMDIO_SMI_READ_VALID with a call to
orion_mdio_wait_ready. This ensures a consistent timeout,
eliminates a busy loop, and allows for use of interrupts on
systems that support them.
Signed-off-by: Leigh Brown <leigh@solinno.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amend orion_mdio_wait_ready so that the same timeout is used when
polling or using wait_event_timeout. Set the timeout to 1ms.
Replace udelay with usleep_range to avoid a busy loop, and set the
polling interval range as 45us to 55us, so that the first sleep
will be enough in almost all cases.
Generate the same log message at timeout when polling or using
wait_event_timeout.
Signed-off-by: Leigh Brown <leigh@solinno.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
include/linux/netdevice.h
net/core/sock.c
Trivial merge issues.
Removal of "extern" for functions declaration in netdevice.h
at the same time "const" was added to an argument.
Two parallel line additions in net/core/sock.c
Signed-off-by: David S. Miller <davem@davemloft.net>
DT-based mv643xx_eth probes and creates platform_devices for the
port devices on its own. To allow fixups for ports based on the
device_node, we need to set .of_node of the corresponding device
with the correct node.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The periodic statistics timer gets started at port _probe() time, but
is stopped on _stop() only. In a modular environment, this can cause
the timer to access already deallocated memory, if the module is unloaded
without starting the eth device. To fix this, we add the timer right
before the port is started, instead of at _probe() time.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each port driver installs a periodic timer to update port statistics
by calling mib_counters_update. As mib_counters_update is also called
from non-timer context, we should not reschedule the timer there but
rather move it to timer-only context.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the memset/memcpy uses of 6 to ETH_ALEN
where appropriate.
Also convert some struct definitions and u8 array
declarations of [6] to ETH_ALEN.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In my patch c194992cbe ("skge: fix
broken driver") I didn't fix the skge bug correctly. The value of the
new mapping (not old) was passed to pci_unmap_single.
If we enable CONFIG_DMA_API_DEBUG, it results in this warning:
WARNING: CPU: 0 PID: 0 at lib/dma-debug.c:986 check_sync+0x4c4/0x580()
skge 0000:02:07.0: DMA-API: device driver tries to sync DMA memory it has
not allocated [device address=0x000000023a0096c0] [size=1536 bytes]
This patch makes the skge driver pass the correct value to
pci_unmap_single and fixes the warning. It copies the old descriptor to
on-stack variable "ee" and unmaps it if mapping of the new descriptor
succeeded.
This patch should be backported to 3.11-stable.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reported-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch 136d8f377e broke the skge driver.
Note this part of the patch:
+ if (skge_rx_setup(skge, e, nskb, skge->rx_buf_size) < 0) {
+ dev_kfree_skb(nskb);
+ goto resubmit;
+ }
+
pci_unmap_single(skge->hw->pdev,
dma_unmap_addr(e, mapaddr),
dma_unmap_len(e, maplen),
PCI_DMA_FROMDEVICE);
skb = e->skb;
prefetch(skb->data);
- skge_rx_setup(skge, e, nskb, skge->rx_buf_size);
The function skge_rx_setup modifies e->skb to point to the new skb. Thus,
after this change, the new buffer, not the old, is returned to the
networking stack.
This bug is present in kernels 3.11, 3.11.1 and 3.12-rc1. The patch should
be queued for 3.11-stable.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Reported-by: Vasiliy Glazov <vascom2@gmail.com>
Tested-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
net/bridge/br_multicast.c
net/ipv6/sit.c
The conflicts were minor:
1) sit.c changes overlap with change to ip_tunnel_xmit() signature.
2) br_multicast.c had an overlap between computing max_delay using
msecs_to_jiffies and turning MLDV2_MRC() into an inline function
with a name using lowercase instead of uppercase letters.
3) stmmac had two overlapping changes, one which conditionally allocated
and hooked up a dma_cfg based upon the presence of the pbl OF property,
and another one handling store-and-forward DMA made. The latter of
which should not go into the new of_find_property() basic block.
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit implements the ->ndo_do_ioctl() operation so that the
PHY-related ioctl() calls can work from userspace, which allows
applications like mii-tool or mii-diag to do their job.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit fixes a long-standing bug that has been reported by many
users: on some Armada 370 platforms, only the network interface that
has been used in U-Boot to tftp the kernel works properly in
Linux. The other network interfaces can see a 'link up', but are
unable to transmit data. The reports were generally made on the Armada
370-based Mirabox, but have also been given on the Armada 370-RD
board.
The network MAC in the Armada 370/XP (supported by the mvneta driver
in Linux) has a functionality that allows it to continuously poll the
PHY and directly update the MAC configuration accordingly (speed,
duplex, etc.). The very first versions of the driver submitted for
review were using this hardware mechanism, but due to this, the driver
was not integrated with the kernel phylib. Following reviews, the
driver was changed to use the phylib, and therefore a software based
polling. In software based polling, Linux regularly talks to the PHY
over the MDIO bus, and sees if the link status has changed. If it's
the case then the adjust_link() callback of the driver is called to
update the MAC configuration accordingly.
However, it turns out that the adjust_link() callback was not
configuring the hardware in a completely correct way: while it was
setting the speed and duplex bits correctly, it wasn't telling the
hardware to actually take into account those bits rather than what the
hardware-based PHY polling mechanism has concluded. So, in fact the
adjust_link() callback was basically a no-op.
However, the network happened to be working because on the network
interfaces used by U-Boot for tftp on Armada 370 platforms because the
hardware PHY polling was enabled by the bootloader, and left enabled
by Linux. However, the second network interface not used for tftp (or
both network interfaces if the kernel is loaded from USB, NAND or SD
card) didn't had the hardware PHY polling enabled.
This patch fixes this situation by:
(1) Making sure that the hardware PHY polling is disabled by clearing
the MVNETA_PHY_POLLING_ENABLE bit in the MVNETA_UNIT_CONTROL
register in the driver ->probe() function.
(2) Making sure that the duplex and speed selections made by the
adjust_link() callback are taken into account by clearing the
MVNETA_GMAC_AN_SPEED_EN and MVNETA_GMAC_AN_DUPLEX_EN bits in the
MVNETA_GMAC_AUTONEG_CONFIG register.
This patch has been tested on Armada 370 Mirabox, and now both network
interfaces are usable after boot.
[ Problem introduced by commit c5aff18 ("net: mvneta: driver for
Marvell Armada 370/XP network unit") ]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Jochen De Smet <jochen.armkernel@leahnim.org>
Cc: Peter Sanford <psanford@nearbuy.io>
Cc: Ethan Tuttle <ethan@ethantuttle.com>
Cc: Chény Yves-Gael <yves@cheny.fr>
Cc: Ryan Press <ryan@presslab.us>
Cc: Simon Guinot <simon.guinot@sequanux.org>
Cc: vdonnefort@lacie.com
Cc: stable@vger.kernel.org
Acked-by: Jason Cooper <jason@lakedaemon.net>
Tested-by: Vincent Donnefort <vdonnefort@gmail.com>
Tested-by: Yves-Gael Cheny <yves@cheny.fr>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
