In sun4/5/6/7i, all the pin function related to NAND0 controller is
named "nand0". However, in sun8i, some of the functions are named as
"nand". This patch renamed them to "nand0", for the consistency.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This SoC has no SD card controller. Nor does it have USB port3.
These pin-mux settings have no point.
Fixes: 70f2f9c4cf ("pinctrl: uniphier: add UniPhier PH1-LD11 pinctrl driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support to mux in the second external bus interface as
follows:
- CS1 and CS2 on GPIO39 and GPIO40 as func 2
- ADDR_7 thru ADDR_0 on GPIO123 thru GPIO130 as func 1
- CS4, CS3 and CS0 on GPIO132, GPIO133, GPIO134 as func 1
- DATA_15 thru DATA_0 on GPIO135 thru GPIO150 as func 1
- OE on GPIO151 as func 1
- ADV on GPIO153 as func 1
- WE on GPIO157 as func 1
This external bus is used on the APQ8060 Dragonboard to connect
an external SMSC9211 ethernet adapter, but there are many other
usecases for the EBI2.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Björn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The msm8974 pinctrl variant has a couple USB HSIC "glue"
registers that let us mux between the pinctrl register settings
or the HSIC core settings for the HSIC pins (gpio 144 and gpio
145). Support this method of operation by adding hsic_data and
hsic_strobe pins that can select between hsic_ctl and gpio
functions. This allows us to toggle the hsic pin configuration
over to the HSIC core at runtime.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The function selection bitfield is not always 3 bits wide.
Sometimes it is 4 bits wide. Let's use the npins struct member to
determine how many bits wide the function selection bitfield is
so we clear the correct amount of bits in the register while
remuxing the pins.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to support the Qualcomm MDM9615 SoC, add support for the TLMM
using the Qualcomm pinctrl generic driver.
Note: the pinctrl is partial, need Documentation to complete all the groups.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
of_find_node_by_name does an of_node_get on its return value,
so an of_node_put is needed on this value before the corresponding
variable goes out of scope.
The Coccinelle semantic patch used to make this change is as follows:
@@
struct device_node *n;
struct device_node *n1;
statement S;
identifier f;
expression E;
constant C;
@@
n = of_find_node_by_name(...)
...
if (!n) S
... when != of_node_put(n)
when != n1 = f(n,...)
when != E = n
when any
when strict
(
+ of_node_put(n);
return -C;
|
of_node_put(n);
|
n1 = f(n,...)
|
E = n
|
return ...;
)
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the initial support of the Broadcom NSP pinmux driver.
Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Voltage switching support for R-Car H3,
- DRIF pin support for R-Car H3,
- Cleanups and fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=z1/q
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v4.8-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v4.8
- Voltage switching support for R-Car H3,
- DRIF pin support for R-Car H3,
- Cleanups and fixes.
This driver adds pinctrl support for Intel Merrifield. The IP block which is
called Family-Level Interface Shim is a separate entity in SoC. The GPIO driver
(gpio-intel-mid.c) will be updated accordingly to support pinctrl interface.
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/freescale/Kconfig:config PINCTRL_MXS
drivers/pinctrl/freescale/Kconfig: bool
...meaning that it currently is not being built as a module by anyone.
It also doesn't have any modular functionality, so it doesn't need
module.h included at all.
What it does have is an exported function that was used as a shared
".remove" by other drivers, but those use cases (imx23 and imx28)
are now gone, and hence this can disappear as well.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX28
drivers/pinctrl/freescale/Kconfig: bool
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_init was not in use by this driver, the init ordering
remains unchanged with this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX23
drivers/pinctrl/freescale/Kconfig: bool
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_init wasn't actually used by this driver, the init
ordering remains unchanged with this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/freescale/Kconfig:config PINCTRL_VF610
drivers/pinctrl/freescale/Kconfig: bool "Freescale Vybrid VF610 pinctrl driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init wasn't in use by this driver, the init ordering
remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX7D
drivers/pinctrl/freescale/Kconfig: bool "IMX7D pinctrl driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this driver, the init ordering
remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Anson Huang <Anson.Huang@freescale.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX6UL
drivers/pinctrl/freescale/Kconfig: bool "IMX6UL pinctrl driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this driver, the init ordering
remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Anson Huang <Anson.Huang@freescale.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX6SX
drivers/pinctrl/freescale/Kconfig: bool "IMX6SX pinctrl driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this driver, the init ordering
remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Anson Huang <Anson.Huang@freescale.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX6SL
drivers/pinctrl/freescale/Kconfig: bool "IMX6SL pinctrl driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this driver, the init ordering
remains unchanged with this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX6Q
drivers/pinctrl/freescale/Kconfig: bool "IMX6Q/DL pinctrl driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We don't replace module.h with init.h since the file already has that.
But we do add export.h since this file uses the global THIS_MODULE.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Dong Aisheng <dong.aisheng@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX6Q
drivers/pinctrl/freescale/Kconfig: bool "IMX6Q/DL pinctrl driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this driver, the init ordering
remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX53
drivers/pinctrl/freescale/Kconfig: bool "IMX53 pinctrl driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this driver, the init ordering
remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Dong Aisheng <dong.aisheng@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX51
drivers/pinctrl/freescale/Kconfig: bool "IMX51 pinctrl driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this driver, the init ordering
remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Dong Aisheng <dong.aisheng@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX50
drivers/pinctrl/freescale/Kconfig: bool "IMX50 pinctrl driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this driver, the init ordering
remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX35
drivers/pinctrl/freescale/Kconfig: bool "IMX35 pinctrl driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this driver, the init ordering
remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Dong Aisheng <dong.aisheng@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX27
drivers/pinctrl/freescale/Kconfig: bool "IMX27 pinctrl driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this driver, the init ordering
remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Markus Pargmann <mpa@pengutronix.de>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX25
drivers/pinctrl/freescale/Kconfig: bool "IMX25 pinctrl driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this driver, the init ordering
remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Denis Carikli <denis@eukrea.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX21
drivers/pinctrl/freescale/Kconfig: bool "i.MX21 pinctrl driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX1
drivers/pinctrl/freescale/Kconfig: bool "IMX1 pinctrl driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
None of these files have anything modular in them, so they
don't need to be bringing in module.h and all its dependencies.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinconf-generic.h file exposes functions for creating generic mappings
but it does not expose a function for freeing the mappings. Add a function
for freeing generic mappings.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix plt clock 3, 4 and 5 pins, which were not in the proper order.
Signed-off-by: Cristina Ciocan <cristina.ciocan@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now we have PINMUX_SINGLE(). Let's use it instead of PINMUX_IPSR_NOGP()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The rockchip_irq_gc_mask_set_bit() function is not exported our used
outside of ppinctrl-rockchip.c so fix the following sparse error by
making it static:
drivers/pinctrl/pinctrl-rockchip.c:2010:6: warning:
symbol 'rockchip_irq_gc_mask_set_bit' was not declared.
Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit 8b2b3dcb34.
Commit 546c6d7930 (pinctrl: digicolor: make it explicitly non-modular) removed
the platform_get_drvdata() call, so platform_set_drvdata() is no longer needed.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
config PINCTRL_AS3722
bool "Pinctrl and GPIO driver for ams AS3722 PMIC"
...meaning that it currently is not being built as a module by anyone.
During an audit for non-modular drivers using modular infrastructure
this driver showed up.
But rather than demodularize it, Laxman indicated that it would be
prefereable to instead convert the driver option to tristate.
This does that, and confirms that it will compile and modpost as
such. However, since I do not have the hardware to confirm that
no new runtime issues exist when modular, that remains untested.
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
config PINCTRL_PALMAS
bool "Pinctrl driver for the PALMAS Series MFD devices"
...meaning that it currently is not being built as a module by anyone.
During an audit for non-modular drivers using modular infrastructure
this driver showed up.
But rather than demodularize it, Laxman indicated that it would be
prefereable to instead convert the driver option to tristate.
This does that, and confirms that it will compile and modpost as
such. However, since I do not have the hardware to confirm that
no new runtime issues exist when modular, that remains untested.
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
I got below build error:
ERROR: "tegra_xusb_padctl_legacy_probe"
[drivers/phy/tegra/phy-tegra-xusb.ko] undefined!
with below build configuration:
CONFIG_ARCH_TEGRA=y
CONFIG_PINCTRL_TEGRA_XUSB=y
CONFIG_PHY_TEGRA_XUSB=y
The problem is below line in drivers/pinctrl/Makefile
obj-$(CONFIG_PINCTRL_TEGRA) += tegra/
So even CONFIG_PINCTRL_TEGRA_XUSB=y is set, kbuild still does not compile
the code in drivers/pinctrl/tegra folder if !CONFIG_PINCTRL_TEGRA.
phy-tegra-xusb.c does not use any symbol from pinctrl-tegra.c,
so build pinctrl-tegra.c only when CONFIG_PINCTRL_TEGRA is set.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With many repeated suspend resume cycles, the pin specific wakeirq
may not always work on omaps. This is because the write to enable the
pin interrupt may not have reached the device over the interconnect
before suspend happens.
Let's fix the issue with a flush of posted write with a readback.
Cc: stable@vger.kernel.org
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some PINs do not have a MUX register, it is not an error.
It is necessary to allow the continuation of the PINs configuration,
otherwise the whole PIN-group will be configured incorrectly.
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This allows to remove the .remove() callback, and all functions and data
it needed for its own bookkeeping.
Suggested-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The Renesas Pin Function Controller uses two header files:
- sh_pfc.h, for use by both core code and SoC-specific drivers,
- core.h, for internal use by the core code only.
Several SoC-specific drivers include core.h, as they need the sh_pfc
structure, which is passed explicitly to the various SoC-specific
callbacks, and used there.
Hence move its definition from core.h to sh_pfc.h, and remove the
inclusion of core.h from all SoC-specific files.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
With C=1:
drivers/pinctrl/sh-pfc/pfc-emev2.c:1695:30: warning: symbol 'emev2_pinmux_info' was not declared. Should it be static?
drivers/pinctrl/sh-pfc/pfc-r8a7779.c:3888:30: warning: symbol 'r8a7779_pinmux_info' was not declared. Should it be static?
Note that there are more warnings on SH.
The sh_pfc_soc_info structure is defined in sh_pfc.h, while all forward
declarations for the SoC-specific versions are in core.h.
Move the forward declarations from core.h to sh_pfc.h to fix this.
Reported-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
When pinctrl_get() is called for a device, it will return a valid handle
even if the device itself has no pinctrl state entries defined in
device-tree. This is caused by the function pinctrl_dt_to_map() which
will return success even if the first pinctrl state, 'pinctrl-0', is not
found in the device-tree node for a device.
According to the pinctrl device-tree binding documentation, pinctrl
states must be numbered starting from 0 and so 'pinctrl-0' should always
be present if a device uses pinctrl and therefore, if 'pinctrl-0' is not
present it seems valid that we should not return a valid pinctrl handle.
Fix this by returning an error code if the property 'pinctrl-0' is not
present for a device.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinctrl-intel needs to use request_irq() instead of chained interrupt
handling because it shares the interrupt with multiple GPIO host
controllers found on Intel CPUs. In -rt all such interrupts are forced to
run in thread context which triggers following warning:
WARNING: CPU: 0 PID: 530 at kernel/irq/handle.c:151 handle_irq_event_percpu+0x23d/0x240
irq 348 handler irq_default_primary_handler+0x0/0x10 enabled interrupts
Modules linked in:
CPU: 0 PID: 530 Comm: irq/14-INT3452: Not tainted 4.6.2-rt5 #1060
0000000000000000 ffff88007a257c98 ffffffff812d8494 ffff88007a257ce8
0000000000000000 ffff88007a257cd8 ffffffff8105e554 000000977a257d90
ffff88007a37a380 000000000000015c 0000000000000002 0000000000000000
Call Trace:
[<ffffffff812d8494>] dump_stack+0x4f/0x6b
[<ffffffff8105e554>] __warn+0xe4/0x100
[<ffffffff8105e5bf>] warn_slowpath_fmt+0x4f/0x60
[<ffffffff810b18f0>] ? __synchronize_hardirq+0x60/0x60
[<ffffffff810b17fd>] handle_irq_event_percpu+0x23d/0x240
[<ffffffff810b1862>] handle_irq_event+0x62/0x90
[<ffffffff810b4e1f>] handle_edge_irq+0x8f/0x190
[<ffffffff810b0d82>] generic_handle_irq+0x22/0x30
[<ffffffff81307abc>] intel_gpio_irq+0xdc/0x150
[<ffffffff810b2293>] irq_forced_thread_fn+0x23/0x70
[<ffffffff810b250b>] irq_thread+0x13b/0x1d0
[<ffffffff8167b844>] ? __schedule+0x2e4/0x5a0
[<ffffffff810b2270>] ? irq_finalize_oneshot.part.37+0xd0/0xd0
[<ffffffff810b25a0>] ? irq_thread+0x1d0/0x1d0
[<ffffffff810b23d0>] ? wake_threads_waitq+0x30/0x30
[<ffffffff8107e624>] kthread+0xd4/0xf0
[<ffffffff8167ec27>] ? _raw_spin_unlock_irq+0x17/0x40
[<ffffffff8167f592>] ret_from_fork+0x22/0x40
[<ffffffff8107e550>] ? kthread_worker_fn+0x190/0x190
The handle_irq_event_* functions (and I suppose generic_handle_irq()) is
expected to be called with interrupts disabled and they rightfully complain
here because we run in thread context with interrupts enabled.
Fix this by adding IRQF_NO_THREAD flag when the master interrupt is
requested. This prevents forced threading of the interrupt used by the GPIO
host controllers.
Reported-by: Kim Tatt Chuah <kim.tatt.chuah@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When running -rt kernel and GPIO interrupt happens we get following
BUG: sleeping function called from invalid context at kernel/locking/rtmutex.c:931
in_atomic(): 1, irqs_disabled(): 0, pid: 530, name: irq/14-INT3452:
Preemption disabled at:[<ffffffff810b4dab>] handle_edge_irq+0x1b/0x190
CPU: 0 PID: 530 Comm: irq/14-INT3452: Not tainted 4.6.2-rt5 #1060
0000000000000000 ffff88007a257d58 ffffffff812d8494 0000000000000000
ffff88017a330000 ffff88007a257d78 ffffffff81083a11 ffff88007a252430
ffff88007a252430 ffff88007a257d90 ffffffff8167ef20 000000000000001a
Call Trace:
[<ffffffff812d8494>] dump_stack+0x4f/0x6b
[<ffffffff81083a11>] ___might_sleep+0xe1/0x160
[<ffffffff8167ef20>] rt_spin_lock+0x20/0x50
[<ffffffff81308c6d>] intel_gpio_irq_ack+0x2d/0x80
[<ffffffff810b4e0b>] handle_edge_irq+0x7b/0x190
[<ffffffff810b0d82>] generic_handle_irq+0x22/0x30
[<ffffffff81307abc>] intel_gpio_irq+0xdc/0x150
[<ffffffff810b2293>] irq_forced_thread_fn+0x23/0x70
[<ffffffff810b250b>] irq_thread+0x13b/0x1d0
[<ffffffff8167b844>] ? __schedule+0x2e4/0x5a0
[<ffffffff810b2270>] ? irq_finalize_oneshot.part.37+0xd0/0xd0
[<ffffffff810b25a0>] ? irq_thread+0x1d0/0x1d0
[<ffffffff810b23d0>] ? wake_threads_waitq+0x30/0x30
[<ffffffff8107e624>] kthread+0xd4/0xf0
[<ffffffff8167ec27>] ? _raw_spin_unlock_irq+0x17/0x40
[<ffffffff8167f592>] ret_from_fork+0x22/0x40
[<ffffffff8107e550>] ? kthread_worker_fn+0x190/0x190
The reason why this happens is because intel_gpio_irq_ack() is called with
desc->lock raw_spinlock locked which cannot sleep but our normal spinlock
(which is converted to rtmutex in -rt) is allowed to sleep. This causes
might_sleep() to trigger.
Fix this by converting the normal spinlock to a raw_spinlock.
Reported-by: Kim Tatt Chuah <kim.tatt.chuah@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These are input-only pins. They do not support drive controlling
in the first place.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
According to the hardware document, setting the drive control is
prohibited for these pins (N-channel Open Drain pins). Set their
drive control attribute to "fixed".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is to cater the need for non-ACPI system whereby
a platform device has to be created in order to bind
with the Apollo Lake Pinctrl GPIO platform driver.
Signed-off-by: Tan Jui Nee <jui.nee.tan@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The recently added max77620 driver fails to build when CONFIG_PINMUX
is not set:
pinctrl/pinctrl-max77620.c:272:21: error: variable 'max77620_pinmux_ops' has initializer but incomplete type
static const struct pinmux_ops max77620_pinmux_ops = {
^~~~~~~~~~
pinctrl/pinctrl-max77620.c:273:2: error: unknown field 'get_functions_count' specified in initializer
This adds the Kconfig 'select' statement that was clearly meant
to be there and is used in all other pinmux drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When building with 'make W=1', we get harmless warnings about
five drivers in drivers/pinctrl, which all contain a copy of
the same line:
drivers/pinctrl/freescale/pinctrl-imx1-core.c:160:1: error: 'inline' is not at beginning of declaration [-Werror=old-style-declaration]
This replaces the somewhat nonstandard 'static const inline'
with 'static inline const', which has the same meaning but
does not cause this warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The strucuture 'max77620_cfg_param' is defined but never used by the
max77620 driver. Remove this structure definition.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pin config get/set handlers for pin groups were previously not
implemented by this driver. The pin_config_group_set is
particularly useful for applying a common config setting to all
pins in a specified group with a single call, without the caller
needing to reference each individual pin by name.
Signed-off-by: Dan O'Donovan <dan@emutex.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On some CHV platforms, we need an option to configure the
open-drain setting for these pins. This adds support for the
PIN_CONFIG_DRIVE_PUSH_PULL and PIN_CONFIG_DRIVE_OPEN_DRAIN to
disable/enable open-drain mode for a specific pin.
Signed-off-by: Dan O'Donovan <dan@emutex.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Due to a silicon issue on the Atom X5-Z8000 "Cherry Trail" processor
series, a common lock must be used to prevent concurrent accesses
across the 4 GPIO controllers managed by this driver.
See Intel Atom Z8000 Processor Series Specification Update
(Rev. 005), errata #CHT34, for further information.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dan O'Donovan <dan@emutex.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PM8058 is found in connection to the APQ8060 on the APQ8060
Dragonboard. Works the same as all others, just add the compatible
string for this variant.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With C=1:
drivers/pinctrl/sh-pfc/pfc-sh7757.c:1613:9: warning: Initializer entry defined twice
drivers/pinctrl/sh-pfc/pfc-sh7757.c:1628:9: also defined here
Remove the duplicate initializer to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Replace the in order struct initialisation style with explicit field
style.
The Coccinelle semantic patch used to make this change is as follows:
@decl@
identifier i1,fld;
type T;
field list[n] fs;
@@
struct i1 {
fs
T fld;
...};
@@
identifier decl.i1,i2,decl.fld;
expression e;
position bad.p, bad.fix;
@@
struct i1 i2@p = { ...,
+ .fld = e
- e@fix
,...};
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The array u300_pmx_registers is not declared or used outside
of the driver, so make it static to avoid the following warning:
drivers/pinctrl/pinctrl-u300.c:673:11: warning: symbol 'u300_pmx_registers' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
drivers/pinctrl/bcm/Makefile properly builds individual drivers based on
their respective Kconfig symbols. ARCH_BCM is currently a menuconfig
option from arch/arm/mach-bcm/Kconfig, which is fine, but prevents ARM64
platforms which do not have such menuconfig option from building their
pinctrl drivers, so let's get rid of that dependency.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are five functions in the driver that are defined but
only used locally. Since these are not used in the current
kernel, delete them to avoid the following warnings:
drivers/pinctrl/nomadik/pinctrl-nomadik.c:1036:6: warning: symbol 'nmk_gpio_clocks_enable' was not declared. Should it be static?
drivers/pinctrl/nomadik/pinctrl-nomadik.c:1050:6: warning: symbol 'nmk_gpio_clocks_disable' was not declared. Should it be static?
drivers/pinctrl/nomadik/pinctrl-nomadik.c:1073:6: warning: symbol 'nmk_gpio_wakeups_suspend' was not declared. Should it be static?
drivers/pinctrl/nomadik/pinctrl-nomadik.c:1094:6: warning: symbol 'nmk_gpio_wakeups_resume' was not declared. Should it be static?
drivers/pinctrl/nomadik/pinctrl-nomadik.c:1120:6: warning: symbol 'nmk_gpio_read_pull' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/Kconfig:config PINCTRL_AT91PIO4
drivers/pinctrl/Kconfig: bool "AT91 PIO4 pinctrl driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/Kconfig:config PINCTRL_DIGICOLOR
drivers/pinctrl/Kconfig: bool
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
config PINCTRL_ZYNQ
bool "Pinctrl driver for Xilinx Zynq"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Sören Brinkmann" <soren.brinkmann@xilinx.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
config PINCTRL_AMD
bool "AMD GPIO pin control"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: Ken Xue <Ken.Xue@amd.com>
Cc: Jeff Wu <Jeff.Wu@amd.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
config PINCTRL_LPC18XX
bool "NXP LPC18XX/43XX SCU pinctrl driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Joachim Eastwood <manabian@gmail.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/Kconfig:config PINCTRL_AT91
drivers/pinctrl/Kconfig: bool "AT91 pinctrl driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not being used in this driver, we don't need
to be concerned with initcall ordering changes when removing it.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
config PINCTRL_BAYTRAIL
bool "Intel Baytrail GPIO pin control"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_init() was already not in use in this driver, we don't
have any concerns with init ordering changes here.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
All known hardware being able to switch voltages has the same POCCTRL
register. So, factor out the common code to the core and keep only
the pin-to-bit mapping SoC specific. Convert the only user, r8a7790.
In case POCCTRL should ever get more complex (more voltages to select?),
we should probably switch over to a describing array like drive strength
does currently.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The atmel_pctl_find_group_by_pin() and the atmel_pinctrl_remove()
functions are not exported, so fix the warnings about these
being exported without definitions by making them static.
drivers/pinctrl/pinctrl-at91-pio4.c:424:20: warning: symbol 'atmel_pctl_find_group_by_pin' was not declared. Should it be static?
drivers/pinctrl/pinctrl-at91-pio4.c:1077:5: warning: symbol 'atmel_pinctrl_remove' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fixup warnings from functions that are not exported and
therefore should be marked static. Fixes:
drivers/pinctrl/bcm/pinctrl-nsp-gpio.c:461:5:
warning: symbol 'nsp_pin_config_group_get' was not declared.
Should it be static?
drivers/pinctrl/bcm/pinctrl-nsp-gpio.c:467:5:
warning: symbol 'nsp_pin_config_group_set' was not declared.
Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
My mistake in the initial support patches.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
An irq which is a wake up source maybe masked unexpectedly if the wake
up source irq was triggered after pinctrl irqchip suspend and before
suspend_device_irqs finished.
Use *_noirq callbacks to guarantee pinctrl irqchip suspend would be
called after suspend_devices_irqs.
Signed-off-by: hongkun.cao <hongkun.cao@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Avoid a gpiochip_free() and use standard functions.
Cc: John Crispin <blogic@openwrt.org>
Cc: Pramod Gurav <pramod.gurav@smartplayin.com>
Cc: Martin Schiller <mschiller@tdt.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rename pinctrl_utils_dt_free_map to pinctrl_utils_free_map, introduced in
d32f7fd3bb ("pinctrl: Rename pinctrl_utils_dt_free_map to pinctrl_utils_free_map")
but not reported into oxnas driver.
Fixes: 611dac1e48 ("pinctrl: Add Oxford Semiconductor OXNAS pinctrl and gpio driver")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently, the UniPhier pinctrl driver itself is a syscon, but it
turned out much more reasonable to make it a child node of a syscon
because our syscon node consists of a bunch of system configuration
registers, not only pinctrl, but also phy, and misc registers.
It is difficult to split the node.
To allow to migrate to the new DT structure, this commit adds new
compatible strings to not disturb the existing DT. After a while,
the old binding will be removed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is needed to get access to UniPhier System Bus (external bus).
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These pins do not support pin-muxing, but it is useful to support
pin configuration for them.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
PH1-LD4 and PH1-sLD8 SoCs have pins that support pin configuration
(pin biasing, drive strength control), but not pin-muxing.
Allow to fill the mux value table with -1 for those pins; pins with
mux value -1 will be skipped in the pin-mux set function. The mux
value type should be changed from "unsigned" to "int" in order to
accommodate -1 as a special case.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Upcoming new pinctrl drivers for PH1-LD11 and PH-LD20 support input
signal gating for each pin. (While, existing ones only support it
per pin-group.) This commit updates the core part for that.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The core part of the UniPhier pinctrl driver needs to support a new
capability for upcoming UniPhier ARMv8 SoCs. This sometimes happens
because pinctrl drivers include really SoC-specific stuff.
This commit intends to tidy up SoC-specific parameters of the existing
drivers before adding the new one. Having just one flag would be
better than adding a new struct member every time a new SoC-specific
capability comes up.
At this time, there is one flag, UNIPHIER_PINCTRL_CAPS_DBGMUX_SEPARATE.
This capability (I'd say rather quirk) was added for PH1-Pro4 and
PH1-Pro5 as requirement from a customer. For those SoCs, one pin-mux
setting is controlled by the combination of two separate registers; the
LSB bits at register offset (8 * N) and the MSB bits at (8 * N + 4).
Because it is impossible to update two separate registers atomically,
the LOAD_PINCTRL register should be set in order to make the pin-mux
settings really effective.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Unfortunately, the pin number of the new SoC, PH1-LD11, is not
contiguous. The base frame work must be adjusted to support the new
SoC pinctrl driver. The pin_desc_get() exploits radix-tree for pin
look-up, so it works more efficiently with sparse pin space.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The new ARMv8 SoC, PH1-LD20, supports more fine-grained drive
strength control. Drive strength of some pins are controlled by
3-bit width registers (8-level granularity).
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The new ARMv8 SoC, PH1-LD20, supports more fine-grained drive
strength control. Some of the configuration registers on it have
3-bit width.
The feature will be supported in the next commit, but a problem is
that macro names are getting longer and longer in the current naming
scheme.
Before moving forward, this commit renames macros as follows:
UNIPHIER_PIN_DRV_4_8 -> UNIPHIER_PIN_DRV_1BIT
UNIPHIER_PIN_DRV_8_12_16_20 -> UNIPHIER_PIN_DRV_2BIT
UNIPHIER_PIN_DRV_FIXED_4 -> UNIPHIER_PIN_DRV_FIXED4
UNIPHIER_PIN_DRV_FIXED_5 -> UNIPHIER_PIN_DRV_FIXED5
UNIPHIER_PIN_DRV_FIXED_8 -> UNIPHIER_PIN_DRV_FIXED8
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently, every SoC driver defines struct pinctrl_desc statically,
i.e. it consumes memory footprint even if it is not probed.
In multi-platform, many pinctrl drivers are linked (generally as
built-in objects), although only one of them is actually used.
So, it is reasonable to allocate memory dynamically where possible.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Every SoC driver sets the same name for struct pinctrl_desc and
platform_driver. The common probe function can set desc->name
instead of duplicating strings in each SoC driver.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The owner of the struct pinctrl_desc matches that of platform_driver.
Set it in the common probe function.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These pin tables were generated by parsing hardware documents with
a script, but the script had a bug. Fix the register offsets.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make function/variable names match the file names for consistency.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To i.MX7D, there are two iomux controllers, iomuxc and iomuxc_lpsr.
They should not share one pin controller descriptor, otherwise
the value filled into imx_pinctrl_desc when probing the first
iomux controller will be overridden when probing the second one.
In this patch, discard the static allcoated imx_pinctrl_desc and
switch to dynamically allcate pin controller descriptor for each
iomux controller.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add EE domain pins for ethernet interface.
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add EE domain pins for UART A, B & C.
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add EE domain pins for eMMC and SD card.
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pins for some more AO domain devices: UART_AO_B and I2C master &
slave.
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-ENOMEM is more suitable error code because kasprintf() fails
in case of memory shortage.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gc_pinctrl_remove() calls platform_get_drvdata(), but I see neither
platform_set_drvdata() nor dev_set_drvdata() anywhere in this driver.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently, struct pinctrl_pin_desc can have per-pin driver private
data, but it is not copied to struct pin_desc.
For a driver with sparse pin space, for-loop search like below would
be necessary in order to get the driver-specific data for a desired
pin number.
for (i = 0; i < pctldev->desc->npins; i++)
if (pin_number == pctldev->desc->pins[i].number)
return pctldev->desc->pins[i].drv_data;
This is not efficient for a driver with a large number of pins.
So, copy the data to struct pin_desc when each pin is registered
for the faster radix tree lookup.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If a pin name is not specified in struct pinctrl_pin_desc,
pinctrl_register_one_pin() dynamically assigns its name.
So, desc->name is always a valid pointer here.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When a dual-edge irq is triggered, an incorrect irq will be reported on
condition that the external signal is not stable and this incorrect irq
has been registered.
Correct the register offset.
Cc: stable@vger.kernel.org
Signed-off-by: Hongkun Cao <hongkun.cao@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The input/output directions were inversed on the GPIO direction
read function. Loose a ! and it is correct.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Although unbinding a pinctrl driver requires root privileges but it
still might be used theoretically in certain attacks (by triggering NULL
pointer exception or memory corruption).
Samsung pincontrol drivers are essential for system operation so their
removal is not expected. They do not implement remove() driver callback
and they are not buildable as modules.
Suppression of the unbinding will prevent triggering NULL pointer
exception like this (Odroid XU3):
$ echo 13400000.pinctrl > /sys/bus/platform/drivers/samsung-pinctrl/unbind
$ cat /sys/kernel/debug/gpio
Unable to handle kernel NULL pointer dereference at virtual address 00000c44
pgd = ec41c000
[00000c44] *pgd=6d448835, *pte=00000000, *ppte=00000000
Internal error: Oops: 17 [#1] PREEMPT SMP ARM
(samsung_gpio_get) from [<c034f9a0>] (gpiolib_seq_show+0x1b0/0x26c)
(gpiolib_seq_show) from [<c01fb8c0>] (seq_read+0x304/0x4b8)
(seq_read) from [<c02dbc78>] (full_proxy_read+0x4c/0x64)
(full_proxy_read) from [<c01d9fb0>] (__vfs_read+0x2c/0x110)
(__vfs_read) from [<c01db400>] (vfs_read+0x8c/0x110)
(vfs_read) from [<c01db4c4>] (SyS_read+0x40/0x8c)
(SyS_read) from [<c01078c0>] (ret_fast_syscall+0x0/0x3c)
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Implement a get_direction callback for the OXNAS GPIO driver in order
to have pin output polarity in debugfs and new userspace ABI.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
MAXIM Semiconductor's PMIC, MAX77620/MAX20024 has 8 GPIO pins
which also act as the special function in alternate mode. Also
there is configuration like push-pull, open drain, FPS timing
etc for these pins.
Add pin control driver to configure these parameters through
pin control APIs.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove the use of parked_reg and use parked_bit for to know
whether field is supported or not.
This is fix for the patch
commit 1d18a3f0f0
"pinctrl: tegra: avoid parked_reg and parked_bank
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pinctrl and gpio control support to Oxford Semiconductor OXNAS SoC Family.
This version supports the ARM926EJ-S based OX810SE SoC with 34 IO pins.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gcc-4.4 and thereabouts has issues with initializers of anonymous
unions, and it generates the following warnings:
drivers/pinctrl/intel/pinctrl-baytrail.c:413: error: unknown field 'simple_funcs' specified in initializer
drivers/pinctrl/intel/pinctrl-baytrail.c:413: warning: missing braces around initializer
drivers/pinctrl/intel/pinctrl-baytrail.c:413: warning: (near initialization for 'byt_score_groups[0].<anonymous>')
drivers/pinctrl/intel/pinctrl-baytrail.c:415: error: unknown field 'simple_funcs' specified in initializer
drivers/pinctrl/intel/pinctrl-baytrail.c:417: error: unknown field 'simple_funcs' specified in initializer
...
Work around this.
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Core changes:
- Add the devm_pinctrl_register() API and switch all applicable drivers
to use it, saving lots of lines of code all over the place.
New drivers:
- New driver for the Broadcom NS2 SoC.
- New subdriver for the PXA25x SoCs.
- New subdriver for the AMLogic Meson GXBB SoC.
Driver improvements:
- The Intel Baytrail driver now properly supports pin control.
- The Nomadik, Rockchip, Broadcom BCM2835 supports the .get_direction() callback in
the GPIO portions.
- Continued development and stabilization of several SH-PFC
SoC subdrivers: r8a7795, r8a7790, r8a7794 etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tlvn
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This kernel cycle was quite calm when it comes to pin control and
there is really just one major change, and that is the introduction of
devm_pinctrl_register() managed resources.
Apart from that linear development, details below.
Core changes:
- Add the devm_pinctrl_register() API and switch all applicable
drivers to use it, saving lots of lines of code all over the place.
New drivers:
- driver for the Broadcom NS2 SoC
- subdriver for the PXA25x SoCs
- subdriver for the AMLogic Meson GXBB SoC
Driver improvements:
- the Intel Baytrail driver now properly supports pin control
- Nomadik, Rockchip, Broadcom BCM2835 support the .get_direction()
callback in the GPIO portions
- continued development and stabilization of several SH-PFC SoC
subdrivers: r8a7795, r8a7790, r8a7794 etc"
* tag 'pinctrl-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (85 commits)
Revert "pinctrl: tegra: avoid parked_reg and parked_bank"
pinctrl: meson: Fix eth_tx_en bit index
pinctrl: tegra: avoid parked_reg and parked_bank
pinctrl: tegra: Correctly check the supported configuration
pinctrl: amlogic: Add support for Amlogic Meson GXBB SoC
pinctrl: rockchip: fix pull setting error for rk3399
pinctrl: stm32: Implement .pin_config_dbg_show()
pinctrl: nomadik: hide nmk_gpio_get_mode when unused
pinctrl: ns2: rename pinctrl_utils_dt_free_map
pinctrl: at91: Merge clk_prepare and clk_enable into clk_prepare_enable
pinctrl: at91: Make at91_gpio_template const
pinctrl: baytrail: fix some error handling in debugfs
pinctrl: ns2: add pinmux driver support for Broadcom NS2 SoC
pinctrl: sirf/atlas7: trivial fix of spelling mistake on flagged
pinctrl: sh-pfc: Kill unused variable in sh_pfc_remove()
pinctrl: nomadik: implement .get_direction()
pinctrl: nomadik: use BIT() with offsets consequently
pinctrl: exynos5440: Use off-stack memory for pinctrl_gpio_range
pinctrl: zynq: Use devm_pinctrl_register() for pinctrl registration
pinctrl: u300: Use devm_pinctrl_register() for pinctrl registration
...
Driver updates for ARM SoCs, these contain various things that touch
the drivers/ directory but got merged through arm-soc for practical
reasons. For the most part, this is now related to power management
controllers, which have not yet been abstracted into a separate
subsystem, and typically require some code in drivers/soc or arch/arm
to control the power domains.
Another large chunk here is a rework of the NVIDIA Tegra USB3.0
support, which was surprisingly tricky and took a long time to
get done.
Finally, reset controller handling as always gets merged through here
as well.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=x+iD
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, these contain various things that touch
the drivers/ directory but got merged through arm-soc for practical
reasons.
For the most part, this is now related to power management
controllers, which have not yet been abstracted into a separate
subsystem, and typically require some code in drivers/soc or arch/arm
to control the power domains.
Another large chunk here is a rework of the NVIDIA Tegra USB3.0
support, which was surprisingly tricky and took a long time to get
done.
Finally, reset controller handling as always gets merged through here
as well"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (97 commits)
arm-ccn: Enable building as module
soc/tegra: pmc: Add generic PM domain support
usb: xhci: tegra: Add Tegra210 support
usb: xhci: Add NVIDIA Tegra XUSB controller driver
dt-bindings: usb: xhci-tegra: Add Tegra210 XUSB controller support
dt-bindings: usb: Add NVIDIA Tegra XUSB controller binding
PCI: tegra: Support per-lane PHYs
dt-bindings: pci: tegra: Update for per-lane PHYs
phy: tegra: Add Tegra210 support
phy: Add Tegra XUSB pad controller support
dt-bindings: phy: tegra-xusb-padctl: Add Tegra210 support
dt-bindings: phy: Add NVIDIA Tegra XUSB pad controller binding
phy: core: Allow children node to be overridden
clk: tegra: Add interface to enable hardware control of SATA/XUSB PLLs
drivers: firmware: psci: make two helper functions inline
soc: renesas: rcar-sysc: Add support for R-Car H3 power areas
soc: renesas: rcar-sysc: Add support for R-Car E2 power areas
soc: renesas: rcar-sysc: Add support for R-Car M2-N power areas
soc: renesas: rcar-sysc: Add support for R-Car M2-W power areas
soc: renesas: rcar-sysc: Add support for R-Car H2 power areas
...
Core infrastructural changes:
- Support for natively single-ended GPIO driver stages. This
means that if the hardware has registers to configure open
drain or open source configuration, we use that rather than
(as we did before) try to emulate it by switching the line
to an input to get high impedance. This is also documented
throughly in Documentation/gpio/driver.txt for those of you
who did not understand one word of what I just wrote.
- Start to do away with the unnecessarily complex and
unitelligible ARCH_REQUIRE_GPIOLIB and
ARCH_WANT_OPTIONAL_GPIOLIB, another evolutional artifact from
the time when the GPIO subsystem was unmaintained. Archs can
now just select GPIOLIB and be done with it, cleanups to
arches will trickle in for the next kernel. Some minor archs
ACKed the changes immediately so these are included in this
pull request.
- Advancing the use of the data pointer inside the GPIO device
for storing driver data by switching the PowerPC, Super-H
Unicore and a few other subarches or subsystem drivers in
ALSA SoC, Input, serial, SSB, staging etc to use it.
- The initialization now reads the input/output state of the
GPIO lines, so that each GPIO descriptor knows - if this
callback is implemented - whether the line is input or
output. This also reflects nicely in userspace "lsgpio".
- It is now possible to name GPIO producer names, line names,
from the device tree. (Platform data has been supported for
a while.) I bet we will get a similar mechanism for ACPI
one of those days. This makes is possible to get sensible
producer names for e.g. GPIO rails in "lsgpio" in userspace.
New drivers:
- New driver for the Loongson1.
- The XLP driver now supports Broadcom Vulcan ARM64.
- The IT87 driver now supports IT8620 and IT8628.
- The PCA953X driver now supports Galileo Gen2.
Driver improvements:
- MCP23S08 was switched to use the gpiolib irqchip helpers and
now also suppors level-triggered interrupts.
- 74x164 and RCAR now supports the .set_multiple() callback
- AMDPT was converted to use generic GPIO.
- TC3589x, TPS65218, SX150X, F7188X, MENZ127, VX855, WM831X, WM8994
support the new single ended callback for open drain
and in some cases open source.
- Implement the .get_direction() callback for a few more drivers
like PL061, Xgene.
Cleanups:
- Paul Gortmaker combed through the drivers and de-modularized
those who are not really modules.
- Move the GPIO poweroff DT bindings to the power subdir where
they belong.
- Rename gpio-generic.c to gpio-mmio.c, which is much more to the
point. That's what it is handling, nothing more, nothing less.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=z4d6
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for kernel cycle v4.7:
Core infrastructural changes:
- Support for natively single-ended GPIO driver stages.
This means that if the hardware has registers to configure open
drain or open source configuration, we use that rather than (as we
did before) try to emulate it by switching the line to an input to
get high impedance.
This is also documented throughly in Documentation/gpio/driver.txt
for those of you who did not understand one word of what I just
wrote.
- Start to do away with the unnecessarily complex and unitelligible
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB, another
evolutional artifact from the time when the GPIO subsystem was
unmaintained.
Archs can now just select GPIOLIB and be done with it, cleanups to
arches will trickle in for the next kernel. Some minor archs ACKed
the changes immediately so these are included in this pull request.
- Advancing the use of the data pointer inside the GPIO device for
storing driver data by switching the PowerPC, Super-H Unicore and
a few other subarches or subsystem drivers in ALSA SoC, Input,
serial, SSB, staging etc to use it.
- The initialization now reads the input/output state of the GPIO
lines, so that each GPIO descriptor knows - if this callback is
implemented - whether the line is input or output. This also
reflects nicely in userspace "lsgpio".
- It is now possible to name GPIO producer names, line names, from
the device tree. (Platform data has been supported for a while).
I bet we will get a similar mechanism for ACPI one of those days.
This makes is possible to get sensible producer names for e.g.
GPIO rails in "lsgpio" in userspace.
New drivers:
- New driver for the Loongson1.
- The XLP driver now supports Broadcom Vulcan ARM64.
- The IT87 driver now supports IT8620 and IT8628.
- The PCA953X driver now supports Galileo Gen2.
Driver improvements:
- MCP23S08 was switched to use the gpiolib irqchip helpers and now
also suppors level-triggered interrupts.
- 74x164 and RCAR now supports the .set_multiple() callback
- AMDPT was converted to use generic GPIO.
- TC3589x, TPS65218, SX150X, F7188X, MENZ127, VX855, WM831X, WM8994
support the new single ended callback for open drain and in some
cases open source.
- Implement the .get_direction() callback for a few more drivers like
PL061, Xgene.
Cleanups:
- Paul Gortmaker combed through the drivers and de-modularized those
who are not really modules.
- Move the GPIO poweroff DT bindings to the power subdir where they
belong.
- Rename gpio-generic.c to gpio-mmio.c, which is much more to the
point. That's what it is handling, nothing more, nothing less"
* tag 'gpio-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (126 commits)
MIPS: do away with ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB
gpio: zevio: make it explicitly non-modular
gpio: timberdale: make it explicitly non-modular
gpio: stmpe: make it explicitly non-modular
gpio: sodaville: make it explicitly non-modular
pinctrl: sh-pfc: Let gpio_chip.to_irq() return zero on error
gpio: dwapb: Add ACPI device ID for DWAPB GPIO controller on X-Gene platforms
gpio: dt-bindings: add wd,mbl-gpio bindings
gpio: of: make it possible to name GPIO lines
gpio: make gpiod_to_irq() return negative for NO_IRQ
gpio: xgene: implement .get_direction()
gpio: xgene: Enable ACPI support for X-Gene GFC GPIO driver
gpio: tegra: Implement gpio_get_direction callback
gpio: set up initial state from .get_direction()
gpio: rename gpio-generic.c into gpio-mmio.c
gpio: generic: fix GPIO_GENERIC_PLATFORM is set to module case
gpio: dwapb: add gpio-signaled acpi event support
gpio: dwapb: convert device node to fwnode
gpio: dwapb: remove name from dwapb_port_property
gpio/qoriq: select IRQ_DOMAIN
...
Fix pinctrl eth_tx_en bit index according to Hardkernel ODROID-C1 datasheet.
Signed-off-by: Alexander Müller <serveralex@gmail.com>
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currrently the gpio_chip.to_irq() callback returns -ENOSYS on error,
which causes bad interactions with the serial_mctrl_gpio helpers.
mctrl_gpio_init() returns -ENOSYS if GPIOLIB is not enabled, which is
intended to be ignored by its callers. However, ignoring -ENOSYS when it
was caused by a gpiod_to_irq() failure will lead to a crash later:
Unable to handle kernel paging request at virtual address ffffffde
...
PC is at mctrl_gpio_set+0x14/0x78
Fix this by returning zero instead, like gpiochip_to_irq() does.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
NVIDIA's Tegra210 support the park bit to make pinmux configuration
enable/disable. If parked bit is 1 then configuration does not apply
and if it is 0 then pinmux configuration applies. This is to support
to avoid any glitch in pinmux configurations.
The parked bit is part of mux register and mux bank and hence it is
not required to have member for the parked_reg and parked bank very
similar to other bit field of the same register.
Remove the need of the parked register and parked bank and get whether
parked function supported or not by parked_bit.
This is to make the parked bit handling same as other fields of mux
registers.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pincontrol registers of Tegra chips has multiple filed per
registers. There is two type of registers mux and drive. All
configurations belongs to one of these registers.
If any configurations are supported then <config>_bit is set to
bit position of these registers otherwise -1 to not support it.
The member is defined as
s32 <config>_bit:6;
So if config is not supported ifor given SoC then it is set to -1
in soc pinmmux table.
In common driver code, to find out that given config is supported
or not, it is checked as:
s8 bit = <config>_bit;
if (bit > 31) {
/* Not supported config */
}
But in this case, bit is s8 and hence for non supporting it is -1.
Correct the check as:
if (bit < 0) {
/* Not supported config */
}
Fixes: e4c02dced9 ("pinctrl: tegra: use signed bitfields for optional fields")
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds the basic platform file to support the pin controller
found on the Amlogic Meson GXBB SoCs.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch fixes the pinctrl pull bias setting, since the pull up/down
setting is the contrary for gpio0(just the gpio0a and gpio0b) and
gpio2(just the gpio2c and gpio2d).
From the TRM said, the gpio0a pull polarity setting:
gpio0a_p
GPIO0A PE/PS programmation section, every
GPIO bit corresponding to 2bits[PS:PE]
2'b00: Z(Normal operation);
2'b11: weak 1(pull-up);
2'b01: weak 0(pull-down);
2'b10: Z(Normal operation);
Then, the other gpios setting as the following:
gpio1a_p (e.g.: gpio1, gpio2a, gpio2b, gpio3...)
GPIO1A PU/PD programmation section, every
GPIO bit corresponding to 2bits
2'b00: Z(Normal operation);
2'b01: weak 1(pull-up);
2'b10: weak 0(pull-down);
2'b11: Z(Normal operation);
For example,(rk3399evb board)
sdmmc_cd --->gpio0_a7
localhost / # io -r -4 0xff320040
ff320040: 00004d5f
In general,the value should be 0x0000cd5f since the pin has been set
in the dts.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: linux-gpio@vger.kernel.org
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This set of patches adds support for the Tegra XUSB pad controller. The
controller provides a set of pads (lanes) that are used for I/O by other
IP blocks within Tegra SoCs (PCIe, SATA and XUSB).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=JRT5
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.7-phy' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
Merge "phy: tegra: Changes for v4.7-rc1" from Thierry Reding:
This set of patches adds support for the Tegra XUSB pad controller. The
controller provides a set of pads (lanes) that are used for I/O by other
IP blocks within Tegra SoCs (PCIe, SATA and XUSB).
* tag 'tegra-for-4.7-phy' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
phy: tegra: Add Tegra210 support
phy: Add Tegra XUSB pad controller support
dt-bindings: phy: tegra-xusb-padctl: Add Tegra210 support
dt-bindings: phy: Add NVIDIA Tegra XUSB pad controller binding
phy: core: Allow children node to be overridden
clk: tegra: Add interface to enable hardware control of SATA/XUSB PLLs
nmk_gpio_get_mode is only used in one place, and that is conditionally
compiled if DEBUG_FS is enabled. A recent cleanup has marked the
definition 'static', which now leads to a warning:
drivers/pinctrl/nomadik/pinctrl-nomadik.c:614:12: error: 'nmk_gpio_get_mode' defined but not used [-Werror=unused-function]
static int nmk_gpio_get_mode(struct nmk_gpio_chip *nmk_chip, int offset)
^~~~~~~~~~~~~~~~~
Moving the function itself inside the #ifdef shuts it up again.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 5e81e0a091 ("pinctrl: nomadik: use BIT() with offsets consequently")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A conflict of two patches caused a build error when a function got renamed
but a new user appeared in the other patch:
drivers/pinctrl/bcm/pinctrl-ns2-mux.c:540:17: error: 'pinctrl_utils_dt_free_map' undeclared here (not in a function)
.dt_free_map = pinctrl_utils_dt_free_map,
^~~~~~~~~~~~~~~~~~~~~~~~~
This renames the new user of pinctrl_utils_dt_free_map accordingly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: d32f7fd3bb ("pinctrl: Rename pinctrl_utils_dt_free_map to pinctrl_utils_free_map")
Fixes: b5aa1006e4 ("pinctrl: ns2: add pinmux driver support for Broadcom NS2 SoC")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This simplifies the normal as well as the error path.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This template is only assigned, so make it const.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Support for the Display Unit on R-Car E2.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vHic
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v4.7-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v4.7 (take two)
- Support for the Display Unit on R-Car E2.
We need to unlock before continuing. Also the continue was accidentally
left out on one error path which would lead to a NULL dereference.
Fixes: 86e3ef812f ('pinctrl: baytrail: Update gpio chip operations')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the initial support of the Broadcom NS2 pinmux driver
Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a new driver for the XUSB pad controller found on NVIDIA Tegra SoCs.
This hardware block used to be exposed as a pin controller, but it turns
out that this isn't a good fit. The new driver and DT binding much more
accurately describe the hardware and are more flexible in supporting new
SoC generations.
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
fix spelling mistake, flaged -> flagged
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The default configuration of a pin is often with a value in the
pull-up/down field at chip reset. So, even if the internal logic of the
controller prevents writing a configuration with pull-up and pull-down at
the same time, we must ensure explicitly this condition before writing the
register.
This was leading to a pull-down condition not taken into account for
instance.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: 776180848b ("pinctrl: introduce driver for Atmel PIO4 controller")
Cc: stable@vger.kernel.org #v4.4 and later
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver is confusing in referencing/dereferencing the global
GPIO number scope in some places and using local offsets in other
places. Remove some of the confusion by removing local "bit" and
"bitmask" definitions and just use BIT(offset) directly. Also
unexport a function only used in this file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The range is registered into a linked list which can be referenced
throughout the lifetime of the driver. Ensure the range's memory is useful
for the same lifetime by adding it to the driver's private data structure.
The bug was introduced in the driver's initial commit, which was present in
v3.10.
Fixes: f0b9a7e521 ("pinctrl: exynos5440: add pinctrl driver for Samsung EXYNOS5440 SoC")
Cc: stable@vger.kernel.org
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use devm_pinctrl_register() for pin control registration and
remove the need of .remove callback.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Sören Brinkmann <soren.brinkmann@xilinx.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use devm_pinctrl_register() for pin control registration and
remove the need of .remove callback.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use devm_pinctrl_register() for pin control registration and
remove the need of .remove callback.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use devm_pinctrl_register() for pin control registration and
remove the need of .remove callback.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use devm_pinctrl_register() for pin control registration.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use devm_pinctrl_register() for pin control registration.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
