The firmware doesn't wait after lifting the PCI reset. However it does
timestamp it in the device tree. We use that to ensure we wait long
enough (3s is our current arbitrary setting) from that timestamp to
actually probing the bus.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This implements support for MSIs on p5ioc2 PHBs. We only support
MSIs on the PCIe PHBs, not the PCI-X ones as the later hasn't been
properly verified in HW.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds support for PCI-X and PCIe on the p5ioc2 IO hub using
OPAL. This includes allocating & setting up TCE tables and config
space access routines.
This also supports fallbacks via RTAS when OPAL is absent, using
legacy TCE format pre-allocated via the device-tree (BML style)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
OPAL can handle various interrupt for us such as Machine Checks (it
performs all sorts of recovery tasks and passes back control to us with
informations about the error), Hardware Management Interrupts and Softpatch
interrupts.
This wires up the mechanisms and prints out specific informations returned
by HAL when a machine check occurs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We do the minimum which is to "pass" interrupts to HAL, which
makes the console smoother and will allow us to implement
interrupt based completion and console.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Implements OPAL RTC and NVRAM support and wire all that up to
the powernv platform.
We use RTAS for RTC as a fallback if available. Using RTAS for nvram
is not supported yet, pending some rework/cleanup and generalization
of the pSeries & CHRP code. We also use RTAS fallbacks for power off
and reboot
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This calls the respective HAL functions, and spin on hal_poll_event()
to ensure the HAL has a chance to communicate with the FSP to trigger
the reboot or shutdown operation
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds a udbg and an hvc console backend for supporting a console
using the OPAL console interfaces.
On OPAL v1 we have hvc0 mapped to whatever console the system was
configured for (network or hvsi serial port) via the service
processor.
On OPAL v2 we have hvcN mapped to the Nth console provided by OPAL
which generally corresponds to:
hvc0 : network console (raw protocol)
hvc1 : serial port S1 (hvsi)
hvc2 : serial port S2 (hvsi)
Note: At this point, early debug console only works with OPAL v1
and shouldn't be enabled in a normal kernel.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add definition of OPAL interfaces along with the wrappers to call
into OPAL runtime and the early device-tree parsing hook to locate
the OPAL runtime firmware.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On machines supporting the OPAL firmware version 1, the system
is initially booted under pHyp. We then use a special hypercall
to verify if OPAL is available and if it is, we then trigger
a "takeover" which disables pHyp and loads the OPAL runtime
firmware, giving control to the kernel in hypervisor mode.
This patch add the necessary code to detect that the OPAL takeover
capability is present when running under PowerVM (aka pHyp) and
perform said takeover to get hypervisor control of the processor.
To perform the takeover, we must first use RTAS (within Open
Firmware runtime environment) to start all processors & threads,
in order to give control to OPAL on all of them. We then call
the takeover hypercall on everybody, OPAL will re-enter the kernel
main entry point passing it a flat device-tree.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds a skeletton for the new Power "Non Virtualized"
platform which will be used by machines supporting running
without an hypervisor, for example in order to run KVM.
These machines will be using a new firmware called OPAL
for which the support will be provided by later patches.
The PowerNV platform is intended to be also usable under
the BML environment used internally for early CPU bringup
which is why the code also supports using RTAS instead of
OPAL in various places.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
