The device has a trap for IPv6 packets that need be routed and have a
unicast link-local destination IP (i.e., fe80::/10). This allows mlxsw
to ignore link-local routes, as the packets will be trapped to the CPU
in any case.
However, since link-local routes are not programmed, it is possible for
routed packets to hit the default route which might also be programmed
to trap packets. This means that packets with a link-local destination
IP might be trapped for the wrong reason.
To overcome this, allow programming link-local prefix routes (usually
one fe80::/64 per-table), so that the packets will be forwarded until
reaching the link-local trap.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bidirectional Forwarding Detection (BFD) provides "low-overhead,
short-duration detection of failures in the path between adjacent
forwarding engines" (RFC 5880).
This is accomplished by exchanging BFD packets between the two
forwarding engines. Up until now these packets were trapped via the
general local delivery (i.e., IP2ME) trap which also traps a lot of
other packets that are not as time-sensitive as BFD packets.
Expose dedicated traps for BFD packets so that user space could
configure a dedicated policer for them.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 packets that need to be forwarded and have a link-local source IP are
dropped by the kernel and an ICMPv6 "Destination unreachable" is sent to
the sending host.
As such, change the trap group of such packets so that they do not
interfere with IPv6 management packets. In the future this trap will be
exposed as an exception via devlink-trap.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Routed IP packets with the Router Alert option need to be trapped to
the CPU as they might need to be locally delivered to raw sockets with
the IP_ROUTER_ALERT / IPV6_ROUTER_ALERT socket option.
Move them to the same group with other packets that might need to be
trapped following route lookup.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the previous patch the split is no longer necessary and all the
trap groups can be moved under the same enum.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As explained in commit e612523041 ("mlxsw: spectrum_trap: Introduce
dummy group with thin policer"), the purpose of the "thin" policer is to
pass as less packets as possible to the CPU.
The identifier of this policer is currently set according to the maximum
number of used trap groups, but this is fragile: On Spectrum-1 the
maximum number of policers is less than the maximum number of trap
groups, which might result in an invalid policer identifier in case the
number of used trap groups grows beyond the policer limit.
Solve this by dynamically allocating the policer identifier.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of Spectrum trap groups is not infinite, but two identifiers
are occupied by SwitchX-2 specific trap groups. Free these identifiers
by moving them out of the main enum.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To align with recent recommended values. Will be configurable by future
patches.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets with an IPv6 link-local destination (i.e., fe80::/10) should not
be forwarded and are therefore trapped to the CPU for local delivery.
Since these packets are trapped for the same logical reason as packets
hitting local routes, associate both traps with the same group.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a packet enters the device it is classified to a filtering
identifier (FID) based on the ingress port and VLAN. The FID miss trap
is used to trap packets for which a FID could not be found.
In mlxsw this trap should only be triggered when a port is enslaved to
an OVS bridge and a matching ACL rule could not be found, so as to
trigger learning.
These packets are therefore completely unrelated to packets hitting
local routes and should be in a different group. Move them.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Group these various IPv6 packets (e.g., router solicitations, router
advertisement) together and subject them to the same policer.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IPv6 Neighbour Discovery (ND) group will be used for various IPv6
packets, not all of which fall under the definition of ND, so rename it
to "IPV6" which is more appropriate.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trap groups that use the same policer settings can share the same switch
case.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets that are trapped via tc's trap action are currently subject to
the same policer as packets hitting local routes. The latter are
critical to the correct functioning of the control plane, while the
former are mainly used for traffic inspection.
Split the ACL trap to a separate group with its own policer. Use a
higher priority for these traps than for traps using mirror action
(e.g., ARP, IGMP). Otherwise, packets matching both traps will not be
forwarded in hardware (because of trap action) and also not forwarded in
software because they will be marked with 'offload_fwd_mark'.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't call netif_napi_del() manually, free_netdev() does this for us.
In addition reorder calls to match reverse order of calls in probe().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit da722186f6 (net: fec: set GPR bit on suspend by DT
configuration) set the GPR reigster offset and bit in driver for
wake on lan feature.
But it introduces two issues here:
- one SOC has two instances, they have different bit
- different SOCs may have different offset and bit
So to support wake-on-lan feature on other i.MX platforms, it should
configure the GPR reigster offset and bit from DT.
So the patch is to improve the commit da722186f6 (net: fec: set GPR
bit on suspend by DT configuration) to support multiple ethernet
instances on i.MX series.
v2:
* switch back to store the quirks bitmask in driver_data
v3:
* suggested by Sascha Hauer, use a struct fec_devinfo for
abstracting differences between different hardware variants,
it can give more freedom to describe the differences.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* hwsim improvements from Jouni and myself, to be able to
test more scenarios easily
* some more HE (802.11ax) support
* some initial S1G (sub 1 GHz) work for fractional MHz channels
* some (action) frame registration updates to help DPP support
* along with other various improvements/fixes
-----BEGIN PGP SIGNATURE-----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=MVBJ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2020-04-25' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
One batch of changes, containing:
* hwsim improvements from Jouni and myself, to be able to
test more scenarios easily
* some more HE (802.11ax) support
* some initial S1G (sub 1 GHz) work for fractional MHz channels
* some (action) frame registration updates to help DPP support
* along with other various improvements/fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver uses a read polling mechanism to check the status of the MDIO
bus, to know if it is ready to accept next commands. This polling
mechanism uses usleep_delay() under the hood between reads which is fine
as long as high resolution timers are enabled. Otherwise the delays will
end up to be much longer than expected.
This patch fixes this by using udelay() under the hood when
CONFIG_HIGH_RES_TIMERS isn't enabled. This increases CPU usage.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MSCC MIIM MDIO driver uses a waiting logic to wait for the MDIO bus
to be ready to accept next commands. It does so by polling the BUSY
status bit which indicates the MDIO bus has completed all pending
operations. This can take time, and the controller supports writing the
next command as soon as there are no pending commands (which happens
while the MDIO bus is busy completing its current command).
This patch implements this improved logic by adding an helper to poll
the PENDING status bit, and by adjusting where we should wait for the
bus to not be busy or to not be pending.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
readl_poll_timeout already returns -ETIMEDOUT if the condition isn't
satisfied, there's no need to check again the condition after calling
it. Remove the redundant timeout check.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MSCC MIIM MDIO driver uses delays to read poll a status register. I
made multiple tests on a Ocelot PCS120 platform which led me to reduce
those delays. The delay in between which the polling function is allowed
to sleep is reduced from 100us to 50us which in almost all cases is a
good value to succeed at the first retry. The overall delay is also
lowered as the prior value was really way to high, 10000us is large
enough.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a recurring pattern throughout some of the PHY code converting
a devad and regnum to our packed clause 45 representation. Rather than
having this scattered around the code, let's put a common translation
function in mdio.h, and provide some register accessors.
Convert the phylib core, phylink, bcm87xx and cortina to use these.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current MPLS dissector only parses the first MPLS Label Stack
Entry (second LSE can be parsed too, but only to set a key_id).
This patch adds the possibility to parse several LSEs by making
__skb_flow_dissect_mpls() return FLOW_DISSECT_RET_PROTO_AGAIN as long
as the Bottom Of Stack bit hasn't been seen, up to a maximum of
FLOW_DIS_MPLS_MAX entries.
FLOW_DIS_MPLS_MAX is arbitrarily set to 7. This should be enough for
many practical purposes, without wasting too much space.
To record the parsed values, flow_dissector_key_mpls is modified to
store an array of stack entries, instead of just the values of the
first one. A bit field, "used_lses", is also added to keep track of
the LSEs that have been set. The objective is to avoid defining a
new FLOW_DISSECTOR_KEY_MPLS_XX for each level of the MPLS stack.
TC flower is adapted for the new struct flow_dissector_key_mpls layout.
Matching on several MPLS Label Stack Entries will be added in the next
patch.
The NFP and MLX5 drivers are also adapted: nfp_flower_compile_mac() and
mlx5's parse_tunnel() now verify that the rule only uses the first LSE
and fail if it doesn't.
Finally, the behaviour of the FLOW_DISSECTOR_KEY_MPLS_ENTROPY key is
slightly modified. Instead of recording the first Entropy Label, it
now records the last one. This shouldn't have any consequences since
there doesn't seem to have any user of FLOW_DISSECTOR_KEY_MPLS_ENTROPY
in the tree. We'd probably better do a hash of all parsed MPLS labels
instead (excluding reserved labels) anyway. That'd give better entropy
and would probably also simplify the code. But that's not the purpose
of this patch, so I'm keeping that as a future possible improvement.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In older FW versions the completion flag was treated as the ack flag in
edpm messages. Expose the FW option of setting which mode the QP is in
by adding a flag to the qedr <-> qed API.
Flag is added for backward compatibility with libqedr.
This flag will be set by qedr after determining whether the libqedr is
using the updated version.
Fixes: f109394033 ("qed: Add support for QP verbs")
Signed-off-by: Yuval Basson <yuval.bason@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sync hw config for RTL8168f/RTL8411 with r8168 vendor driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sync hw config for RTL8168evl with r8168 vendor driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sync hw config for RTL8168h with r8168 vendor driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sync hw config for RTL8168g with r8168 vendor driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Second set of patches for v5.8. Lots of new features and new supported
hardware for mt76. Also rtw88 got new hardware support.
Major changes:
rtw88
* add support for Realtek 8723DE PCI adapter
* rename rtw88.ko/rtwpci.ko to rtw88_core.ko/rtw88_pci.ko
iwlwifi
* stop supporting swcrypto and bt_coex_active module parameters on
mvm devices
* enable A-AMSDU in low latency
mt76
* new devices for mt76x0/mt76x2
* support for non-offload firmware on mt7663
* hw/sched scan support for mt7663
* mt7615/mt7663 MSI support
* TDLS support
* mt7603/mt7615 rate control fixes
* new driver for mt7915
* wowlan support for mt7663
* suspend/resume support for mt7663
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJey69PAAoJEG4XJFUm622bIcEH/iT2M037SSfySAdykAvUQHJU
E1E9iZKJVVKZ+8nfTh03thtT4HyPC0jZMjWrqL5N4PFTKJKJo/t9HfAEq4niboGj
l2jeqQpujck7zUBKQh4HWWJiDtpOiMUS9noHSujnS4NThtRo/+/qxIiCz6nxVBix
DHKi+zZR4t05U3UYYivWc/CfojIXLrqeZl187MnDBV6LvNP8/en+HpmnCzp/trFn
qxBl2MWzr1oZf8j+t1UPtDVnUz1OMcHvnCQosQMeBwNtkkqKGc7Cip6VG/fqsLau
HdLwQWvsRByFT7yaXbwI+/uOMZhZ/KPWx9BdDdistegxyE8fZvjs/csfk7p3lSc=
=sKYR
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.8
Second set of patches for v5.8. Lots of new features and new supported
hardware for mt76. Also rtw88 got new hardware support.
Major changes:
rtw88
* add support for Realtek 8723DE PCI adapter
* rename rtw88.ko/rtwpci.ko to rtw88_core.ko/rtw88_pci.ko
iwlwifi
* stop supporting swcrypto and bt_coex_active module parameters on
mvm devices
* enable A-AMSDU in low latency
mt76
* new devices for mt76x0/mt76x2
* support for non-offload firmware on mt7663
* hw/sched scan support for mt7663
* mt7615/mt7663 MSI support
* TDLS support
* mt7603/mt7615 rate control fixes
* new driver for mt7915
* wowlan support for mt7663
* suspend/resume support for mt7663
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Print certain name string instead of hard-coded "memory" for dev_err
output, which would be more accurate and helpful for debugging.
Signed-off-by: Wang Wenhu <wenhu.wang@vivo.com>
Cc: Alex Elder <elder@kernel.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x_warpcore_read_sfp_module_eeprom() can call bnx2x_bsc_read()
three times before giving up.
This causes latency blips of at least 31 ms (58 ms being reported
by our teams)
Convert the long lasting loops of udelay() to usleep_range() ones,
and breaks the loops on precise time tracking.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ariel Elior <aelior@marvell.com>
Cc: Sudarsana Kalluru <skalluru@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For XDP the MVNETA_SKB_HEADROOM is used as an offset for
the received data.
The MVNETA manual states that the last 3 bits assumed to be 0.
This is currently the case but lets make it explicit in the definition
to prevent future problems.
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix incorrect spelling of "advertisement".
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rate with which packets are sampled is determined by user space, so
there is no need to associate such packets with a policer.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both packet types are needed for the same reason (neighbour discovery),
so associate them with the same trap group.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ARP trap group will be used for IPv6 ND traps in the next patch, so
rename it to "NEIGH_DISCOVERY" which is more appropriate.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that traffic class (TC) and priority are set to the same value,
there is no need to store both. Remove the first.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The traffic class (TC) attribute of packet traps determines through which
TC a packet trap will be scheduled through the CPU port.
The priority attribute determines which trap will be triggered in case
several packet traps match a packet.
We try to configure these attributes to the same value for all packet
traps as there is little reason not to.
Some packet traps did not use the same value, so rectify that now.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As explained in commit 9ffcc3725f ("mlxsw: spectrum: Allow packets to
be trapped from any PG"), incoming packets can be admitted to the shared
buffer and forwarded / trapped, if:
(Ingress{Port}.Usage < Thres && Ingress{Port,PG}.Usage < Thres &&
Egress{Port}.Usage < Thres && Egress{Port,TC}.Usage < Thres)
||
(Ingress{Port}.Usage < Min || Ingress{Port,PG} < Min ||
Egress{Port}.Usage < Min || Egress{Port,TC}.Usage < Min)
Trapped packets are scheduled to transmission through the CPU port.
Currently, the minimum and maximum quotas of traffic class (TC) 0 of the
CPU port are 0, which means it is not usable.
Assign non-zero quotas to TC 0 of the CPU port, so that it could be
utilized by subsequent patches.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce the default acceptable rate of DHCP packets to 128 packets per
second and reduce their priority. This is reasonable given the Spectrum
ASICs are limited to 128 ports at the moment.
These are only the default values. Users will be able to modify them via
devlink-trap.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, IPv4 DHCP packets are trapped during L2 forwarding, which
means that packets might be trapped unnecessarily. Instead, only trap
the DHCP packets that reach the router. Either because they were flooded
to the router port or forwarded to it by the FDB. This is consistent
with the corresponding IPv6 trap.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both packet types are needed for the same reason (multicast snooping),
so associate them with the same trap group.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IGMP trap group will be used for MLD traps in the next patch, so
rename it to "MC_SNOOPING" which is more appropriate.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MSCC bug fix in 'net' had to be slightly adjusted because the
register accesses are done slightly differently in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new devres variant of register_netdev() in the mtk-star-emac
driver and shrink the code by a couple lines.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the mask argument as it's not used by r8168ep_ocp_read().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All callers read the full 32bit value, therefore the mask argument can
be removed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl_eri_read() returns the full 32bit value, therefore there's no
benefit in writing back parts of it only. handle it like the vendor
driver and write the full 32 bit always. Omitting the mask argument
avoids some overhead and makes the code better readable.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
