we can also have babble conditions with LS/FS
and we also want to recover in that case.
Because of that we will drop the check of HSMODE
and always try to run babble recovery.
Suggested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There's no point is splitting those anymore.
We're now also able to drop another forward
declaration.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
that's not needed anymore. Everything that we
call is irq-safe, so we might as well not
have a delayed work for babble recovery.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
recover is a much better name than reset, considering
we don't really reset the IP, just run platform-specific
babble recovery algorithm.
while at that, also fix a typo in comment and add kdoc
for recover memeber of platform_ops.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
we're not resetting musb at all, just restarting
the session. This means we don't need to touch PHYs
or VBUS or anything like that. Just make sure session
bit is reenabled after MUSB dropped it.
while at that, make sure to tell usbcore that we're
dropping the session and, thus, disconnecting the
device.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
All we have to do is, really, drop session bit
and let the session restart.
Big thanks goes to Bin Liu <b-liu@ti.com> for
inspiring this work.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When babble IRQ happens, we need to wait only
5.3us (320 cycles of 60MHz clock), we will give
it some slack and schedule our work a 10 usecs into
the future.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We do *not* want to touch devctl at all when
trying to recover from babble. All we want to
do is mask IRQs until we're done without our
babble recovery, at which point we will unmask
IRQs.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
sometimes we want to just mask/unmask interrupts
without touching devctl register. For those
cases, let's introduce musb_enable_interrupts and
musb_disable_interrupts()
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Whenever babble happens, MUSB controller will
drop session automatically.
The only case where it won't drop the session,
is when we're running on AM335x and SW_SESSION_CTRL
bit has been set. In that case, controller will
not touch session bit so SW has a chance to recover
from babble condition.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We want to check if that particular bit is
set. It could very well be that bootloader
(or romcode) has fiddled with MUSB before
us which could leave other bits set in this
register.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
musb->int_usb already contains the correct
information for musb-core to handle babble.
In fact, this very check was just causing a
nonsensical babble interrupt storm.
With this I can get test.sh to run and, even though
all tests fail with timeout, that's still better
than locking up the system due to IRQ storm.
Also, if I remove g_zero and load g_mass_storage,
then everything works fine again.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
when musb is operating as host and a remote wakeup
fires up, a resume interrupt will be raised. At that
point SUSPENDM bit is automatically cleared and
RESUME bit is automatically set.
Remove those two from IRQ handler.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There was already a proper place where we were
checking for babble interrupts, move babble
recovery there.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
if reset fails, we should return a *negative*
error code, not a positive value.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
FSDEV is set for both HIGH and FULL speeds,
the correct HIGHSPEED check is done through
power register's HSMODE bit.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
devctl & MUSB_DEVCTL_HM represents a single bit,
just check for the bit, there's really no need
to compare the result against 0.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As per the SAF1761 data sheet[0], the DcChipID register represents
the hardware version number (0001h) and the chip ID (1582h) for the
Peripheral Controller.
However as per the ISP1761 data sheet[1], the DcChipID register
represents the hardware version number (0015h) and the chip ID (8210h)
for the Peripheral Controller.
This patch adds support for both the chip ID values.
[0] http://www.nxp.com/documents/data_sheet/SAF1761.pdf
[1] http://pdf.datasheetcatalog.com/datasheets2/74/742102_1.pdf
Cc: Felipe Balbi <balbi@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Removed FIXME from usb/dwc3/dwc3-pci.c by moving definition of
PCI_VENDOR_ID_SYNOPSYS shared with usb/dwc2 to linux/pci_ids.h.
Signed-off-by: Joseph Kogut <joseph.kogut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The seq_printf return value, because it's frequently misused,
will eventually be converted to void.
See: commit 1f33c41c03 ("seq_file: Rename seq_overflow() to
seq_has_overflowed() and make public")
While there, simplify the error handler logic by returning
immediately and remove the unnecessary labels.
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The function regulator_set_optimum_mode() is changing name to
regulator_set_load(), so update the code accordingly.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The function regulator_set_optimum_mode() is changing name to
regulator_set_load(), so update the code accordingly.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As per the SAF1761 data sheet[0], the DcChipID register represents
the hardware version number (0001h) and the chip ID (1582h) for the
Peripheral Controller.
However as per the ISP1761 data sheet[1], the DcChipID register
represents the hardware version number (0015h) and the chip ID (8210h)
for the Peripheral Controller.
This patch adds support for both the chip ID values.
[0] http://www.nxp.com/documents/data_sheet/SAF1761.pdf
[1] http://pdf.datasheetcatalog.com/datasheets2/74/742102_1.pdf
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The IRQF_DISABLED is a NOOP and scheduled to be removed. According to
commit e58aa3d2d0 ("genirq: Run irq handlers with interrupts
disabled") running IRQ handlers with interrupts enabled can cause stack
overflows when the interrupt line of the issuing device is still active.
This patch removes using this deprecated flag and additionally removes
redundantly setting IRQF_SHARED for isp1760_udc_register().
Signed-off-by: Valentin Rothberg <Valentin.Rothberg@lip6.fr>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
A recent bug fix I did that was marked for stable backports
introduced a slightly wrong dependency on CONFIG_OMAP_CONTROL_PHY.
I was missing the fact that the PHY driver already stubs out the
omap_control_usb_set_mode, and we only need to add a dependency
to prevent the musb-omap2430 driver from being built-in when
the phy driver is a loadable module, but we should not prevent it
from being built altogether when the phy driver is disabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: ca784be36c ("usb: start using the control module driver")
Cc: <stable@vger.kernel.org> # v3.9+
Acked-by: Acked-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Now that we're using XFERINPROGRESS for all endpoint
types (except Control), we will *always* be completing
one TRB at a time, so it's safe to remove the loop
from dwc3_cleanup_done_reqs.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes a bug where removing dwc3-omap.ko
would not trigger removal of dwc3.ko.
of_platform_depopulate() already bakes an easy to
use API for removing all our children which were
populated during probe(); Let's use that one instead
of cooking our own solution.
Note that this is kind of a revert of commit c5a1fbc
(usb: dwc3: dwc3-omap: Fix the crash on module removal)
although we can't simply revert that because a direct
call to platform_device_unregister would also be flakey.
Signed-off-by: Felipe Balbi <balbi@ti.com>
That trick is only needed if we end up with an error, so
there's no point in messing that outside of an error path.
In fact doing so causes problems when removing dwc3.ko,
problems which commit c5a1fbc (usb: dwc3: dwc3-omap: Fix
the crash on module removal) mistakenly tried to fix.
Signed-off-by: Felipe Balbi <balbi@ti.com>
instead of using manually spelled out bit-shits
and iterate over each of the 16-bits (one for
each endpoint) on each direction, we can make use
of for_each_set_bit() which internally uses
find_first_bit().
This makes the code slightly more readable while
also making we only iterate over bits which are
actually set.
Signed-off-by: Felipe Balbi <balbi@ti.com>
As per Mentor Graphics' documentation, we should
always handle TX endpoints before RX endpoints.
This patch fixes that error while also updating
some hard-to-read comments which were scattered
around musb_interrupt().
This patch should be backported as far back as
possible since this error has been in the driver
since it's conception.
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Here's a round of USB fixes for 4.0-rc3.
Nothing major, the usual gadget, xhci and usb-serial fixes and a few new
device ids as well.
All have been in linux-next successfully.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlT8Q2oACgkQMUfUDdst+ym9cgCgloBq7GqYw5lnW+zVy6fmyS3U
zHMAoMYPLjpUuO4tHfXt46NxVHIMzGsg
=TMtd
-----END PGP SIGNATURE-----
Merge tag 'usb-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here's a round of USB fixes for 4.0-rc3.
Nothing major, the usual gadget, xhci and usb-serial fixes and a few
new device ids as well.
All have been in linux-next successfully"
* tag 'usb-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (36 commits)
xhci: Workaround for PME stuck issues in Intel xhci
xhci: fix reporting of 0-sized URBs in control endpoint
usb: ftdi_sio: Add jtag quirk support for Cyber Cortex AV boards
USB: ch341: set tty baud speed according to tty struct
USB: serial: cp210x: Adding Seletek device id's
USB: pl2303: disable break on shutdown
USB: mxuport: fix null deref when used as a console
USB: serial: clean up bus probe error handling
USB: serial: fix port attribute-creation race
USB: serial: fix tty-device error handling at probe
USB: serial: fix potential use-after-free after failed probe
USB: console: add dummy __module_get
USB: ftdi_sio: add PIDs for Actisense USB devices
Revert "USB: serial: make bulk_out_size a lower limit"
cdc-acm: Add support for Denso cradle CU-321
usb-storage: support for more than 8 LUNs
uas: Add US_FL_NO_REPORT_OPCODES for JMicron JMS539
USB: usbfs: don't leak kernel data in siginfo
xhci: Clear the host side toggle manually when endpoint is 'soft reset'
xhci: Allocate correct amount of scratchpad buffers
...
Final methods start with get_ready_ep(), which will fail unless we have
->state == STATE_EP_ENABLED. So they'd be failing just fine until that
first write() anyway. Let's do the following:
* get_ready_ep() gets a new argument - true when called from
ep_write_iter(), false otherwise.
* make it quiet when it finds STATE_EP_READY (no printk, that is;
the case won't be impossible after that change).
* when that new argument is true, treat STATE_EP_READY the same
way as STATE_EP_ENABLED (i.e. return zero and do not unlock).
* in ep_write_iter(), after success of get_ready_ep() turn
if (!usb_endpoint_dir_in(&epdata->desc)) {
into
if (epdata->state == STATE_EP_ENABLED &&
!usb_endpoint_dir_in(&epdata->desc)) {
- that logics only applies after config.
* have ep_config() take kernel-side buffer (i.e. use memcpy()
instead of copy_from_user() in there) and in the "let's call ep_io or
ep_aio" (again, in ep_write_iter()) add "... or ep_config() in case it's
not configured yet"
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Make sure to handle an infinite timeout (0).
Note that wait_until_sent is currently never called with a 0-timeout
argument due to a bug in tty_wait_until_sent.
Fixes: dcf0105039 ("USB: serial: add generic wait_until_sent
implementation")
Cc: stable <stable@vger.kernel.org> # v3.10
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xhci in Intel Sunrisepoint and Cherryview platforms need a driver
workaround for a Stuck PME that might either block PME events in suspend,
or create spurious PME events preventing runtime suspend.
Workaround is to clear a internal PME flag, BIT(28) in a vendor specific
PMCTRL register at offset 0x80a4, in both suspend resume callbacks
Without this, xhci connected usb devices might never be able to wake up the
system from suspend, or prevent device from going to suspend (xhci d3)
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a control transfer has a short data stage, the xHCI controller generates
two transfer events: a COMP_SHORT_TX event that specifies the untransferred
amount, and a COMP_SUCCESS event. But when the data stage is not short, only the
COMP_SUCCESS event occurs. Therefore, xhci-hcd must set urb->actual_length to
urb->transfer_buffer_length while processing the COMP_SUCCESS event, unless
urb->actual_length was set already by a previous COMP_SHORT_TX event.
The driver checks this by seeing whether urb->actual_length == 0, but this alone
is the wrong test, as it is entirely possible for a short transfer to have an
urb->actual_length = 0.
This patch changes the xhci driver to rely on a new td->urb_length_set flag,
which is set to true when a COMP_SHORT_TX event is received and the URB length
updated at that stage.
This fixes a bug which affected the HSO plugin, which relies on URBs with
urb->actual_length == 0 to halt re-submitting the RX URB in the control
endpoint.
Cc: <stable@vger.kernel.org>
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are a few fixes for reported problems including a usb-debug device
buffer overflow, potential use-after-free on failed probe, and a couple
of issues with the USB console.
Some new device IDs are also added.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=0CrX
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.0-rc3
Here are a few fixes for reported problems including a usb-debug device
buffer overflow, potential use-after-free on failed probe, and a couple
of issues with the USB console.
Some new device IDs are also added.
Signed-off-by: Johan Hovold <johan@kernel.org>
This patch integrates Cyber Cortex AV boards with the existing
ftdi_jtag_quirk in order to use serial port 0 with JTAG which is
required by the manufacturers' software.
Steps: 2
[ftdi_sio_ids.h]
1. Defined the device PID
[ftdi_sio.c]
2. Added a macro declaration to the ids array, in order to enable the
jtag quirk for the device.
Signed-off-by: Max Mansfield <max.m.mansfield@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The V4L2 core will warn if this is not done. Unfortunately this driver
wasn't updated.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of .ioctl use unlocked_ioctl. This allows us to finally remove
the old .ioctl op.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Switch this driver over to the V4L2 core locking mechanism in preparation
for switching to unlocked_ioctl. Suggested by Laurent Pinchart.
This patch introduces a new mutex at the struct uvc_video level and
drops the old mutex at the queue level. The new lock is now used for all
ioctl locking and in the release file operation (the driver always has
to take care of locking in file operations, the core only serializes
ioctls).
Note that the mmap and get_unmapped_area file operations no longer take
a lock. Commit f035eb4e97 fixed a AB-BA
deadlock by moving all the locking down into vb2, so the mmap and
get_unmapped_area file operations should no longer do any locking before
calling into vb2.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The ch341_set_baudrate() function initialize the device baud speed
according to the value on priv->baud_rate. By default the ch341_open() set
it to a hardcoded value (DEFAULT_BAUD_RATE 9600). Unfortunately, the
tty_struct is not initialized with the same default value. (usually 56700)
This means that the tty_struct and the device baud rate generator are not
synchronized after opening the port.
Fixup is done by calling ch341_set_termios() if tty exist.
Remove unnecessary variable priv->baud_rate setup as it's already done by
ch341_port_probe().
Remove unnecessary call to ch341_set_{handshake,baudrate}() in
ch341_open() as there already called in ch341_configure() and
ch341_set_termios()
Signed-off-by: Nicolas PLANEL <nicolas.planel@enovance.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
These device ID's are not associated with the cp210x module currently,
but should be. This patch allows the devices to operate upon connecting
them to the usb bus as intended.
Signed-off-by: Michiel van de Garde <mgparser@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Remove redundant call to ch341_close from error path when submission of
the interrupt urb fails in open.
Signed-off-by: Johan Hovold <johan@kernel.org>
Currently an enabled break state is not disabled on final close nor on
re-open and has to be disabled manually.
Fix this by disabling break on port shutdown.
Reported-by: Jari Ruusu <jariruusu@users.sourceforge.net>
Tested-by: Jari Ruusu <jariruusu@users.sourceforge.net>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix null-pointer dereference at probe when the device is used as a
console, in which case the tty argument to open will be NULL.
Fixes: ee467a1f20 ("USB: serial: add Moxa UPORT 12XX/14XX/16XX
driver")
Cc: stable <stable@vger.kernel.org> # v3.14
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <greg@kroah.com>
Fix attribute-creation race with userspace by using the port device
groups field to create the port attributes.
Also use %u when printing the port number, which is unsigned, even
though we do not currently support more than 128 ports per device.
Reported-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <greg@kroah.com>
Add missing error handling when registering the tty device at port
probe. This avoids trying to remove an uninitialised character device
when the port device is removed.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Takashi Iwai <tiwai@suse.de>
Cc: stable <stable@vger.kernel.org> # v2.6.12
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <greg@kroah.com>
Fix return value in probe error path, which could end up returning
success (0) on errors. This could in turn lead to use-after-free or
double free (e.g. in port_remove) when the port device is removed.
Fixes: c706ebdfc8 ("USB: usb-serial: call port_probe and port_remove
at the right times")
Cc: stable <stable@vger.kernel.org> # v2.6.31
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <greg@kroah.com>
Add call to __module_get when initialising the fake tty in
usb_console_setup to match the module_put in release_one_tty.
Note that the tty-driver (i.e. usb-serial core) must be compiled-in to
enable the usb console so the __module_get is essentially a noop as
driver->owner will be null.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Johan Hovold <johan@kernel.org>
These product identifiers (PID) all deal with marine NMEA format data
used on motor boats and yachts. We supply the programmed devices to
Chetco, for use inside their equipment. The PIDs are a direct copy of
our Windows device drivers (FTDI drivers with altered PIDs).
Signed-off-by: Mark Glover <mark@actisense.com>
Cc: stable <stable@vger.kernel.org>
[johan: edit commit message slightly ]
Signed-off-by: Johan Hovold <johan@kernel.org>
This reverts commit 5083fd7bdf.
A bulk-out size smaller than the end-point size is indeed valid. The
offending commit broke the usb-debug driver for EHCI debug devices,
which use 8-byte buffers.
Fixes: 5083fd7bdf ("USB: serial: make bulk_out_size a lower limit")
Reported-by: "Li, Elvin" <elvin.li@intel.com>
Cc: stable <stable@vger.kernel.org> # v3.15
Signed-off-by: Johan Hovold <johan@kernel.org>
In order to support an older USB cradle by Denso, I added its vendor- and product-ID to the array of usb_device_id acm_ids. In this way cdc-acm feels responsible for this cradle. The related /dev/ttyACM node is being created properly, and the data transfer works.
However, later cradle models by Denso do have proper descriptors, so the patch is not required for these. At the same time both the older and the later model have the same vendor- and product-ID, but they both work with the patched driver.
Declaration of the Denso cradles I tested:
- both models have the same IDs: vendorID 0x076d, productID 0x0006
- older model: Denso CU-321 (descriptors not properly set)
- later model: Denso CU-821 (with proper descriptors)
Signed-off-by: Bjoern Gerhart <oss@airbjorn.de>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is necessary to make some storage arrays work.
Some storage devices have more than 8 LUNs. In addition
you can hook up a WideSCSI bus to USB. In these cases even
level 2 devices can have more than 8 LUNs. For them
it is necessary to simply believe the class specific
command and report its result back to the SCSI layer.
Off by one Alan noticed is fixed.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like the JMicron JMS567 enclosures with the JMS539 choke on report-opcodes,
so avoid it.
Tested-and-reported-by: Tom Arild Naess <tanaess@gmail.com>
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a signal is delivered, the information in the siginfo structure
is copied to userspace. Good security practice dicatates that the
unused fields in this structure should be initialized to 0 so that
random kernel stack data isn't exposed to the user. This patch adds
such an initialization to the two places where usbfs raises signals.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Dave Mielke <dave@mielke.cc>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Main benefit of this is to get xhci connected USB scanners to work.
Some devices use a clear endpoint halt request as a 'soft reset' even if
the endpoint is not halted. This will clear the toggle and sequence on the
device side. xHCI however refuses to reset a non-halted endpoint, so instead
we need to issue a configure endpoint command on xHCI to clear its host side
toggle and sequence, and get it in sync with the device side.
Tested-by: Mike Mammarella <mikem@crystalorb.net>
Cc: <stable@vger.kernel.org> # v3.18
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Include the high order bit fields for Max scratchpad buffers when
calculating how many scratchpad buffers are needed.
I'm suprised this hasn't caused more issues, we never allocated more than
32 buffers even if xhci needed more. Either we got lucky and xhci never
really used past that area, or then we got enough zeroed dma memory anyway.
Should be backported as far back as possible
Reported-by: Tim Chen <tim.c.chen@linux.intel.com>
Tested-by: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 9737479285 ("usb: host: xhci-plat: add support for the Armada
375/38x XHCI controllers") extended the xhci-plat driver to support the Armada
375/38x SoCs, mostly by adding a quirk configuring the MBUS window.
However, that quirk was run before the clock the controllers needs has been
enabled. This usually worked because the clock was first enabled by the
bootloader, and left as such until the driver is probe, where it tries to
access the MBUS configuration registers before enabling the clock.
Things get messy when EPROBE_DEFER is involved during the probe, since as part
of its error path, the driver will rightfully disable the clock. When the
driver will be reprobed, it will retry to access the MBUS registers, but this
time with the clock disabled, which hangs forever.
Fix this by running the quirks after the clock has been enabled by the driver.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "Extended Compat ID OS Feature Descriptor Specification" does not
require the (sub)compatible ids to be NUL-terminated, because they
are placed in a fixed-size buffer and only unused parts of it should
contain NULs. If the buffer is fully utilized, there is no place for NULs.
Consequently, the code which uses desc->ext_compat_id never expects the
data contained to be NUL terminated.
If the compatible id is stored after sub-compatible id, and the compatible
id is full length (8 bytes), the (useless) NUL terminator overwrites the
first byte of the sub-compatible id.
If the sub-compatible id is full length (8 bytes), the (useless) NUL
terminator ends up out of the buffer. The situation can happen in the RNDIS
function, where the buffer is a part of struct f_rndis_opts. The next
member of struct f_rndis_opts is a mutex, so its first byte gets
overwritten. The said byte is a part of a mutex'es member which contains
the information on whether the muext is locked or not. This can lead to a
deadlock, because, in a configfs-composed gadget when a function is linked
into a configuration with config_usb_cfg_link(), usb_get_function()
is called, which then calls rndis_alloc(), which tries locking the same
mutex and (wrongly) finds it already locked.
This patch eliminates NUL terminating of the (sub)compatible id.
Cc: <stable@vger.kernel.org> # v3.16+
Fixes: da4243145f: "usb: gadget: configfs: OS Extended Compatibility descriptors support"
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In the wrapper the IRQ disable should be done by writing 1's to the
IRQ*_CLR register. Existing code is broken because it instead writes
zeros to IRQ*_SET register.
Fix this by adding functions dwc3_omap_write_irqmisc_clr() and
dwc3_omap_write_irq0_clr() which do the right thing.
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: <stable@vger.kernel.org> # v3.2+
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this patch fixes following sparse warnings:
uvc_v4l2.c:264:29: warning: symbol 'uvc_v4l2_ioctl_ops' was not declared. Should it be static?
uvc_v4l2.c:355:29: warning: symbol 'uvc_v4l2_fops' was not declared. Should it be static?
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this patch fixes following sparse warnings:
g_ffs.c:136:3: warning: symbol 'gfs_configurations' was not declared. Should it be static?
g_ffs.c:281:16: warning: Using plain integer as NULL pointer
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this patch fixes following sparse warnings:
uvc_video.c:283:5: warning: symbol 'uvcg_video_pump' was not declared. Should it be static?
uvc_video.c:342:5: warning: symbol 'uvcg_video_enable' was not declared. Should it be static?
uvc_video.c:381:5: warning: symbol 'uvcg_video_init' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this patch fixes following sparse warnings:
f_sourcesink.c:347:34: warning: symbol 'ss_int_source_comp_desc' was not declared. Should it be static?
f_sourcesink.c:365:34: warning: symbol 'ss_int_sink_comp_desc' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this patch fixes following sparse warnings:
f_uac2.c:57:12: warning: symbol 'uac2_name' was not declared. Should it be static?
f_uac2.c:637:36: warning: symbol 'in_clk_src_desc' was not declared. Should it be static?
f_uac2.c:649:36: warning: symbol 'out_clk_src_desc' was not declared. Should it be static?
f_uac2.c:661:39: warning: symbol 'usb_out_it_desc' was not declared. Should it be static?
f_uac2.c:675:39: warning: symbol 'io_in_it_desc' was not declared. Should it be static?
f_uac2.c:689:40: warning: symbol 'usb_in_ot_desc' was not declared. Should it be static?
f_uac2.c:703:40: warning: symbol 'io_out_ot_desc' was not declared. Should it be static?
f_uac2.c:716:34: warning: symbol 'ac_hdr_desc' was not declared. Should it be static?
f_uac2.c:754:34: warning: symbol 'as_out_hdr_desc' was not declared. Should it be static?
f_uac2.c:767:38: warning: symbol 'as_out_fmt1_desc' was not declared. Should it be static?
f_uac2.c:775:32: warning: symbol 'fs_epout_desc' was not declared. Should it be static?
f_uac2.c:785:32: warning: symbol 'hs_epout_desc' was not declared. Should it be static?
f_uac2.c:831:34: warning: symbol 'as_in_hdr_desc' was not declared. Should it be static?
f_uac2.c:844:38: warning: symbol 'as_in_fmt1_desc' was not declared. Should it be static?
f_uac2.c:852:32: warning: symbol 'fs_epin_desc' was not declared. Should it be static?
f_uac2.c:862:32: warning: symbol 'hs_epin_desc' was not declared. Should it be static?
f_uac2.c:1566:21: warning: symbol 'afunc_alloc' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this patch fixes following sparse warning:
f_hid.c:572:30: warning: symbol 'f_hidg_fops' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is only an API consolidation and should make things more readable
it replaces var * HZ / 1000 by msecs_to_jiffies(var).
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We still have a combination of legacy phys and generic phys in
use so we need to support both types of phy for musb_dsps.c.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The renesas usbhs driver calls extcon_get_edev_by_phandle(), which
is defined in drivers/extcon/extcon-class.c, and that can be a
loadable module. If the extcon-class support is disabled, usbhs
will work correctly for all devices that do not need extcon.
However, if extcon-class is a loadable module, and usbhs is
built-in, the kernel fails to link. In order to solve that,
we need a Kconfig dependency that allows extcon to be disabled
but does not allow usbhs built-in if extcon is a module.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The value for the multipoint dts property is ignored when parsing with
of_property_read_bool, so we currently have multipoint always set as 1
even if value 0 is specified in the dts file.
Let's fix this to read the value too instead of just the property like
the binding documentation says as otherwise MUSB will fail to work
on devices with Mentor configuration that does not support multipoint.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We need a pm_runtime_get_sync() call from
within musb_gadget_pullup() to make sure
registers are accessible at that time.
The problem is that musb_gadget_pullup() is
called with IRQs disabled and, because of that,
we need to tell pm_runtime that this pm_runtime_get_sync()
is IRQ safe.
We can simply add pm_runtime_irq_safe(), however, because
we need to make our read/write accessor function pointers
have been initialized before trying to use them. This means
that all pm_runtime initialization for musb_core needs to
be moved down so that when we call pm_runtime_irq_safe(),
the pm_runtime_get_sync() that it calls on the parent, won't
cause a crash due to NULL musb_read/write accessors.
Reported-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
f_phonet's ->set_alt() method will call usb_ep_disable()
potentially on an endpoint which is already disabled. That's
something the gadget/function driver must guarantee that it's
always balanced.
In order to balance the calls, just make sure the endpoint
was enabled before by means of checking the validity of
driver_data.
Reported-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Enable HCD_BH flag for musb host controller driver.
This improves the MSC/UVC through put. With this enabled
even 640x480@30fps webcam streaming is also supported.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Pull kconfig updates from Michal Marek:
"Yann E Morin was supposed to take over kconfig maintainership, but
this hasn't happened. So I'm sending a few kconfig patches that I
collected:
- Fix for missing va_end in kconfig
- merge_config.sh displays used if given too few arguments
- s/boolean/bool/ in Kconfig files for consistency, with the plan to
only support bool in the future"
* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kconfig: use va_end to match corresponding va_start
merge_config.sh: Display usage if given too few arguments
kconfig: use bool instead of boolean for type definition attributes
AIO_PREAD requests call ->aio_read() with iovec on caller's stack, so if
we are going to access it asynchronously, we'd better get ourselves
a copy - the one on kernel stack of aio_run_iocb() won't be there
anymore. function/f_fs.c take care of doing that, legacy/inode.c
doesn't...
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull networking updates from David Miller:
1) Missing netlink attribute validation in nft_lookup, from Patrick
McHardy.
2) Restrict ipv6 partial checksum handling to UDP, since that's the
only case it works for. From Vlad Yasevich.
3) Clear out silly device table sentinal macros used by SSB and BCMA
drivers. From Joe Perches.
4) Make sure the remote checksum code never creates a situation where
the remote checksum is applied yet the tunneling metadata describing
the remote checksum transformation is still present. Otherwise an
external entity might see this and apply the checksum again. From
Tom Herbert.
5) Use msecs_to_jiffies() where applicable, from Nicholas Mc Guire.
6) Don't explicitly initialize timer struct fields, use setup_timer()
and mod_timer() instead. From Vaishali Thakkar.
7) Don't invoke tg3_halt() without the tp->lock held, from Jun'ichi
Nomura.
8) Missing __percpu annotation in ipvlan driver, from Eric Dumazet.
9) Don't potentially perform skb_get() on shared skbs, also from Eric
Dumazet.
10) Fix COW'ing of metrics for non-DST_HOST routes in ipv6, from Martin
KaFai Lau.
11) Fix merge resolution error between the iov_iter changes in vhost and
some bug fixes that occurred at the same time. From Jason Wang.
12) If rtnl_configure_link() fails we have to perform a call to
->dellink() before unregistering the device. From WANG Cong.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (39 commits)
net: dsa: Set valid phy interface type
rtnetlink: call ->dellink on failure when ->newlink exists
com20020-pci: add support for eae single card
vhost_net: fix wrong iter offset when setting number of buffers
net: spelling fixes
net/core: Fix warning while make xmldocs caused by dev.c
net: phy: micrel: disable NAND-tree for KSZ8021, KSZ8031, KSZ8051, KSZ8081
ipv6: fix ipv6_cow_metrics for non DST_HOST case
openvswitch: Fix key serialization.
r8152: restore hw settings
hso: fix rx parsing logic when skb allocation fails
tcp: make sure skb is not shared before using skb_get()
bridge: netfilter: Move sysctl-specific error code inside #ifdef
ipv6: fix possible deadlock in ip6_fl_purge / ip6_fl_gc
ipvlan: add a missing __percpu pcpu_stats
tg3: Hold tp->lock before calling tg3_halt() from tg3_init_one()
bgmac: fix device initialization on Northstar SoCs (condition typo)
qlcnic: Delete existing multicast MAC list before adding new
net/mlx5_core: Fix configuration of log_uar_page_sz
sunvnet: don't change gso data on clones
...
Pull debugfs patches from Al Viro:
"debugfs patches, mostly to make it possible for something like tracefs
to be transparently automounted on given directory in debugfs.
New primitive in there is debugfs_create_automount(name, parent, func,
arg), which creates a directory and makes its ->d_automount() return
func(arg). Another missing primitive was debugfs_create_file_size() -
open-coded in quite a few places. Dave's patch adds it and converts
the open-code instances to calling it"
* 'debugfs_automount' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
debugfs: Provide a file creation function that also takes an initial size
new primitive: debugfs_create_automount()
debugfs: split end_creating() into success and failure cases
debugfs: take mode-dependent parts of debugfs_get_inode() into callers
fold debugfs_mknod() into callers
fold debugfs_create() into caller
fold debugfs_mkdir() into caller
debugfs_mknod(): get rid useless arguments
fold debugfs_link() into caller
debugfs: kill __create_file()
debugfs: split the beginning and the end of __create_file() off
debugfs_{mkdir,create,link}(): get rid of redundant argument
These are changes for drivers that are intimately tied to some SoC
and for some reason could not get merged through the respective
subsystem maintainer tree.
This time around, much of this is for at91, with the bulk of it being syscon
and udc drivers.
Also, there's:
- coupled cpuidle support for Samsung Exynos4210
- Renesas 73A0 common-clk work
- of/platform changes to tear down DMA mappings on device destruction
- a few updates to the TI Keystone knav code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=T7R2
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"These are changes for drivers that are intimately tied to some SoC and
for some reason could not get merged through the respective subsystem
maintainer tree.
This time around, much of this is for at91, with the bulk of it being
syscon and udc drivers.
Also, there's:
- coupled cpuidle support for Samsung Exynos4210
- Renesas 73A0 common-clk work
- of/platform changes to tear down DMA mappings on device destruction
- a few updates to the TI Keystone knav code"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
cpuidle: exynos: add coupled cpuidle support for exynos4210
ARM: EXYNOS: apply S5P_CENTRAL_SEQ_OPTION fix only when necessary
soc: ti: knav_qmss_queue: change knav_range_setup_acc_irq to static
soc: ti: knav_qmss_queue: makefile tweak to build as dynamic module
pcmcia: at91_cf: depend on !ARCH_MULTIPLATFORM
soc: ti: knav_qmss_queue: export API calls for use by user driver
of/platform: teardown DMA mappings on device destruction
usb: gadget: at91_udc: Allocate udc instance
usb: gadget: at91_udc: Update DT binding documentation
usb: gadget: at91_udc: Rework for multi-platform kernel support
usb: gadget: at91_udc: Simplify probe and remove functions
usb: gadget: at91_udc: Remove non-DT handling code
usb: gadget: at91_udc: Document DT clocks and clock-names property
usb: gadget: at91_udc: Drop uclk clock
usb: gadget: at91_udc: Fix clock names
mfd: syscon: Add Atmel SMC binding doc
mfd: syscon: Add atmel-smc registers definition
mfd: syscon: Add Atmel Matrix bus DT binding documentation
mfd: syscon: Add atmel-matrix registers definition
clk: shmobile: fix sparse NULL pointer warning
...
Provide a file creation function that also takes an initial size so that the
caller doesn't have to set i_size, thus meaning that we don't have to call
deal with ->d_inode in the callers.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Here's the big pull request for the USB driver tree for 3.20-rc1.
Nothing major happening here, just lots of gadget driver updates, new
device ids, and a bunch of cleanups.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlTgtrcACgkQMUfUDdst+yn0tACgygJPNvu1l3ukNJCCpWuOErIj
3KsAnjiEXv90DLYJiVLJ4EbLPw0V9wAv
=DrJx
-----END PGP SIGNATURE-----
Merge tag 'usb-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg KH:
"Here's the big pull request for the USB driver tree for 3.20-rc1.
Nothing major happening here, just lots of gadget driver updates, new
device ids, and a bunch of cleanups.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (299 commits)
usb: musb: fix device hotplug behind hub
usb: dwc2: Fix a bug in reading the endpoint directions from reg.
staging: emxx_udc: fix the build error
usb: Retry port status check on resume to work around RH bugs
Revert "usb: Reset USB-3 devices on USB-3 link bounce"
uhci-hub: use HUB_CHAR_*
usb: kconfig: replace PPC_OF with PPC
ehci-pci: disable for Intel MID platforms (update)
usb: gadget: Kconfig: use bool instead of boolean
usb: musb: blackfin: remove incorrect __exit_p()
USB: fix use-after-free bug in usb_hcd_unlink_urb()
ehci-pci: disable for Intel MID platforms
usb: host: pci_quirks: joing string literals
USB: add flag for HCDs that can't receive wakeup requests (isp1760-hcd)
USB: usbfs: allow URBs to be reaped after disconnection
cdc-acm: kill unnecessary messages
cdc-acm: add sanity checks
usb: phy: phy-generic: Fix USB PHY gpio reset
usb: dwc2: fix USB core dependencies
usb: renesas_usbhs: fix NULL pointer dereference in dma_release_channel()
...
printk and friends can now format bitmaps using '%*pb[l]'. cpumask
and nodemask also provide cpumask_pr_args() and nodemask_pr_args()
respectively which can be used to generate the two printf arguments
necessary to format the specified cpu/nodemask.
* drivers/uwb/drp.c::uwb_drp_handle_alien_drp() was formatting mas.bm
into a buffer but never used it. Removed.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the normal {} instead of a macro to terminate an array.
Remove the macro too.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the normal {} instead of a macro to terminate an array.
Remove the macro too.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This one was driving me mad, with several lines of warnings during the
allmodconfig build for a single bogus pointer cast. The warning was so
verbose due to the indirect macro expansion explanation, and the whole
thing was just for a debug printout.
The bogus pointer-to-integer cast was pointless anyway, so just remove
it, and use '%p' to show the pointer.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In commit ceb6c9c862 ("USB / PM: Drop CONFIG_PM_RUNTIME from the
USB core"), all occurrences of CONFIG_PM_RUNTIME in the USB core
code were replaced by CONFIG_PM. This created the following structure
of #ifdef blocks in drivers/usb/core/hub.c:
[...]
#ifdef CONFIG_PM
#ifdef CONFIG_PM
/* always on / undead */
#else
/* dead */
#endif
[...]
This patch removes unnecessary inner "#ifdef CONFIG_PM" as well as
the corresponding dead #else block. This inconsistency was found using
the undertaker-checkpatch tool.
Signed-off-by: Andreas Ruprecht <rupran@einserver.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Here's the big pull request for Gadgets and PHYs. It's
a total of 217 non-merge commits with pretty much everything
being touched.
The most important bits are a ton of new documentation for
almost all usb gadget functions, a new isp1760 UDC driver,
several improvements to the old net2280 UDC driver, and
some minor tracepoint improvements to dwc3.
Other than that, a big list of minor cleanups, smaller bugfixes
and new features all over the place.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJU0lRFAAoJEIaOsuA1yqRE17sP/R4iPwrPQGVQBaqg5AOHZGEe
dKf9GqZZIPzNIs4146Ua5W/9d4U6zQKndy+fRQaNEVc2SR3Tm0IwOSokvSaC3FYr
NEGHMoRnTWd/JWSVB/6sy0qn8rKRMbkxR7u9lG9M/JACUymn3NJfH4D0jq85ewPR
0Tjv4g5wGnv3YEmnWgR5ieFgn0OxgUBiGUF7QufgMp7G3F2hjmeligBD0jt3w6tD
G4oMHp+pRfPCcm8mcdiHoP3aXOtNJ824rI+b1EZkKBKeo7FxRDIe48Vl107XOpOB
yUFnQVGZazh1Oi6Vxmh9O1mmjpNOir/4dni7gZfh1uGC7cJ7tSkOfbN4jH4Ycsay
Ckt8XQkmf/z9VWTONsAkDwfPhnMbxCafz8Fi/UdOXsoR69YV1MKnt1zRN5dzgNq9
7EIqDwPPJi6qwLACoqxVYknSmXQqhW8B0IMPpMqEByvR1mnIOWomlFot63AufMaQ
+uS7JGJguUmMvkyP1FJRKcPsd9u4PYll5JzymPsvSB6xtDisVFqYb3BbfieZHpBn
+/ZFqltT71pQ3TxIx2ZiTk1e91PiKJUbEQikV6TBiLhgtkpn2J8obHtF50K4+xHh
wXOU3VHFd2ZONN+WB5F5EoVtZiwsd3pARr8QJRcVhdXltTWElJ2qsA4Z1+5QVhAy
mqXYcwsvBe9C+5p2pYwR
=bGMq
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.20 merge window
Here's the big pull request for Gadgets and PHYs. It's
a total of 217 non-merge commits with pretty much everything
being touched.
The most important bits are a ton of new documentation for
almost all usb gadget functions, a new isp1760 UDC driver,
several improvements to the old net2280 UDC driver, and
some minor tracepoint improvements to dwc3.
Other than that, a big list of minor cleanups, smaller bugfixes
and new features all over the place.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The commit 889ad3b "usb: musb: try a race-free wakeup" breaks device
hotplug enumeraitonn when the device is connected behind a hub while usb
autosuspend is enabled.
Adding finish_resume_work into runtime resume callback fixes the issue.
Also resume root hub is required to resume the bus from runtime suspend,
so move musb_host_resume_root_hub() back to its original location, where
handles RESUME interrupt.
Signed-off-by: Bin Liu <b-liu@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
According to the DWC2 datasheet, the HWCFG1 register stores
the configured endpoint directions for endpoints 0-15 in bit positions
0-31.
==========================
Endpoint Direction (EpDir)
This 32-bit field uses two bits per endpoint to determine the endpoint
direction.
Endpoint
Bits [31:30]: Endpoint 15 direction
Bits [29:28]: Endpoint 14 direction
....
Bits [3:2]: Endpoint 1 direction
Bits[1:0]: Endpoint 0 direction (always BIDIR)
==========================
The DWC2 driver is currently interpreting the contents of the register
as directions for endpoints 1-15 which leads to an error in determining
the configured endpoint directions in the core because the first 2 bits
determine the direction of endpoint 0 and not 1.
This is based on testing/next branch in Felipe's git.
Signed-off-by: Roshan Pius <rpius@chromium.org>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The EHCI controller on the RK3288 SoC is violating basic parts of the
USB spec and thereby unable to properly resume a suspended port. It does
not start SOF generation within 3ms of finishing resume signaling, so
the attached device will drop of the bus again. This is a particular
problem with runtime PM, where accessing the device will trigger a
resume that immediately makes it unavailable (and reenumerate with a new
handle).
Thankfully, the persist feature is generally able to work around stuff
like that. Unfortunately, it doesn't quite work in this particular case
because the controller will turn off the CurrentConnectStatus bit for an
instant while the device is reconnecting, which causes the kernel to
conclude that it permanently disappeared. This patch adds a tiny retry
mechanism to the core port resume code which will catch this case and
shouldn't have any notable impact on other controllers.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This revert a82b76f7fa.
The commit causes an extra reset in remote wakeup as described in:
http://www.spinics.net/lists/linux-usb/msg119080.html
Signed-off-by: Zhuang Jin Can <jin.can.zhuang@intel.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare number to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PPC_OF is a ppc specific option which is used to mean that the
firmware device tree access functions are available. Since all the
ppc platforms have a device tree, it is aways set to 'y' for ppc.
So it makes no sense to keep a such option in the current kernel.
Replace it with PPC
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a follow up to the previously submitted commit cefa9a31a5 (ehci-pci:
disable for Intel MID platforms).
It includes the following changes:
- table and function are renamed to reflect this is not only about ChipIdea
- ChipIdea PCI driver (ci_hdrc_pci.c) gets the comment about the table in
ehci-pci.c
- MIPS IDs removed from the list since it was discovered and tested on Intel
MID platforms
Reviewed-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
bfin_remove() is not (nor should it be) marked as __exit, so we should
not be using __exit_p() wrapper with it, otherwise unbinding through
sysfs does not work properly.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The usb_hcd_unlink_urb() routine in hcd.c contains two possible
use-after-free errors. The dev_dbg() statement at the end of the
routine dereferences urb and urb->dev even though both structures may
have been deallocated.
This patch fixes the problem by storing urb->dev in a local variable
(avoiding the dereference of urb) and moving the dev_dbg() up before
the usb_put_dev() call.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Joe Lawrence <joe.lawrence@stratus.com>
Tested-by: Joe Lawrence <joe.lawrence@stratus.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
On some Intel MID platforms the ChipIdea USB controller is used. The EHCI PCI
is in conflict with the proper driver. The patch makes ehci-pci to be ignored
in favour of ChipIdea controller.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
The patch joins the string literals for happy debugging. There is no functional
change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
Currently the USB stack assumes that all host controller drivers are
capable of receiving wakeup requests from downstream devices.
However, this isn't true for the isp1760-hcd driver, which means that
it isn't safe to do a runtime suspend of any device attached to a
root-hub port if the device requires wakeup.
This patch adds a "cant_recv_wakeups" flag to the usb_hcd structure
and sets the flag in isp1760-hcd. The core is modified to prevent a
direct child of the root hub from being put into runtime suspend with
wakeup enabled if the flag is set.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Nicolas Pitre <nico@linaro.org>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
The usbfs API has a peculiar hole: Users are not allowed to reap their
URBs after the device has been disconnected. There doesn't seem to be
any good reason for this; it is an ad-hoc inconsistency.
The patch allows users to issue the USBDEVFS_REAPURB and
USBDEVFS_REAPURBNDELAY ioctls (together with their 32-bit counterparts
on 64-bit systems) even after the device is gone. If no URBs are
pending for a disconnected device then the ioctls will return -ENODEV
rather than -EAGAIN, because obviously no new URBs will ever be able
to complete.
The patch also adds a new capability flag for
USBDEVFS_GET_CAPABILITIES to indicate that the reap-after-disconnect
feature is supported.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Chris Dickens <christopher.a.dickens@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
Memory allocation failures are reported by a central facility.
No need to repeat the job.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check the special CDC headers for a plausible minimum length.
Another big operating systems ignores such garbage.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
CC: stable@vger.kernel.org
Reviewed-by: Adam Lee <adam8157@gmail.com>
Tested-by: Adam Lee <adam8157@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just another device id for cp210x.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=2F/N
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-3.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
USB-serial fixes for v3.19-rc7
Just another device id for cp210x.
Signed-off-by: Johan Hovold <johan@kernel.org>
Removal of dead code in mos7840 and a clean-up of the option blacklist
handling.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=NeuI
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v3.20-rc1
Removal of dead code in mos7840 and a clean-up of the option blacklist
handling.
Signed-off-by: Johan Hovold <johan@kernel.org>
Since commit e9f2cefb0c ("usb: phy: generic: migrate to gpio_desc") a
kernel hang is observed on imx51-babbage board:
[ 1.392824] ci_hdrc ci_hdrc.1: doesn't support gadget
[ 1.397975] ci_hdrc ci_hdrc.1: EHCI Host Controller
[ 1.403205] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1
[ 1.422335] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
[ 1.432962] hub 1-0:1.0: USB hub found
[ 1.437119] hub 1-0:1.0: 1 port detected
This hang happens because the reset GPIO stays at logic level 0.
The USB PHY reset gpio is defined in the dts file as:
reset-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>;
, which means it is active low, so what the gpio reset pin needs to do in this
case is the following:
- Go to logic level 0 to reset the USB PHY
- Stay at 0 for a bit
- Go back to logic level 1
When switching to gpiod API we need to following according to
Documentation/gpio/consumer.txt:
"The first thing a driver must do with a GPIO is setting its direction. If no
direction-setting flags have been given to gpiod_get*(), this is done by
invoking one of the gpiod_direction_*() functions:
int gpiod_direction_input(struct gpio_desc *desc)
int gpiod_direction_output(struct gpio_desc *desc, int value)"
Since no direction-setting flags have been given to devm_gpiod_get_optional()
in our case, we need to use gpiod_direction_output to comply with the gpiod API.
With this change the USB PHY reset performs a proper reset, the kernel boots
fine and USB host is functional.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It is currently possible to configure the dwc2 driver as built-in
when host mode or dual-role is enabled, but the USB core is
a loadable module. This leads to a link failure:
drivers/built-in.o: In function `_dwc2_hcd_start':
:(.text+0x84538): undefined reference to `usb_hcd_resume_root_hub'
drivers/built-in.o: In function `_dwc2_hcd_urb_dequeue':
:(.text+0x84aa0): undefined reference to `usb_hcd_check_unlink_urb'
:(.text+0x84e4c): undefined reference to `usb_hcd_unlink_urb_from_ep'
:(.text+0x84e74): undefined reference to `usb_hcd_giveback_urb'
drivers/built-in.o: In function `dwc2_assign_and_init_hc':
:(.text+0x86b98): undefined reference to `usb_hcd_unmap_urb_for_dma'
drivers/built-in.o: In function `_dwc2_hcd_urb_enqueue':
:(.text+0x8717c): undefined reference to `usb_hcd_link_urb_to_ep'
:(.text+0x872f4): undefined reference to `usb_hcd_unlink_urb_from_ep'
drivers/built-in.o: In function `dwc2_host_complete':
:(.text+0x875d4): undefined reference to `usb_hcd_unlink_urb_from_ep'
:(.text+0x87600): undefined reference to `usb_hcd_giveback_urb'
drivers/built-in.o: In function `dwc2_hcd_init':
:(.text+0x87ba8): undefined reference to `usb_disabled'
:(.text+0x87d38): undefined reference to `usb_create_hcd'
:(.text+0x88094): undefined reference to `usb_add_hcd'
:(.text+0x880dc): undefined reference to `usb_put_hcd'
drivers/built-in.o: In function `dwc2_hcd_remove':
:(.text+0x8821c): undefined reference to `usb_remove_hcd'
:(.text+0x8823c): undefined reference to `usb_put_hcd'
drivers/built-in.o: In function `dwc2_hc_handle_tt_clear.isra.10':
:(.text+0x88e2c): undefined reference to `usb_hub_clear_tt_buffer'
drivers/built-in.o: In function `dwc2_hcd_qtd_add':
:(.text+0x8b554): undefined reference to `usb_calc_bus_time'
To fix the problem, this patch changes the dependencies so that
dwc2 host mode can only be enabled if either the USB core is
built-in or both USB and dwc2 are modules.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes an issue that the following commit causes NULL
pointer dereference in dma_release_channel().
"usb: renesas_usbhs: add support for requesting DT DMA"
(commit id abd2dbf6bb)
The usbhsf_dma_init_dt() should set fifo->{t,r}x_chan to NULL if
dma_request_slave_channel_reason() returns IS_ERR value.
Otherwise, usbhsf_dma_quit() will call dma_release_channel(), and then
NULL pointer dereference happens.
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Reported-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Declare the interrupt as "one shot" so that it is masked until the end
of the threaded handler. This prevents the irq core from spitting out an
error :
"Threaded irq requested with handler=NULL and !ONESHOT for irq 63"
This was introduced by commit "usb: phy: generic: add vbus support".
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
All the gpios, ie. reset-gpios and vbus-detect-gpio, should be optional
and not prevent the driver from working. Fix the regression in the
behavior introduced by commit "usb: phy: generic: migrate to gpio_desc".
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
USB reset interrupt is no more used to reset the controller.
Thus, reset the controller in pullup callback as described by
Synopsys programming guide. Otherwise enumeration sometimes
fails when usb configuration is switched without physical
disconnection.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Defines are more readable and searchable than constants.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
hsotg->phyif is set in dwc2_gadget_init according to phy interface
width. Use it for configuration instead of hardcoded value.
Moreover, set USB turnaround time according to phy width.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Print debug message according to zlp direction. Always saying
"Sending" is misleading.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Pullup doesn't need to be enabled during usb reset since it is
already enabled. This leads to shorter chirp-k duration if done
during usb reset.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add a flag to request physical reset of the controller when
s3c_hsotg_core_init_disconnected is called.
During the usb reset, controller must not be fully reconfigured and
resetted. Else this leads to shorter chirp-k duration during
enumeration.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When using DMA, dwc2 requires buffers to be 4 bytes aligned. Use
bounce buffers if they are not.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove dead code as well.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
s3c_hsotg_process_req_feature comments was not correct
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Handle SET_FEATURE TEST_MODE request sent by the host.
Slightly rework FEATURE request handling to allow parsing
other request types than Endpoint.
Also add a debugfs to change test mode value from user space.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When clearing HALT on an endpoint, req->complete of in progress
requests must be called with locks off. New request should only be
started if there is not already a pending request on the endpoint.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When a remote wakeup happens during bus_suspend, hcd needs to resume
its root hub.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The omap musb front-end calls into the phy driver directly
instead of using a generic phy interface, which causes a link
error when the specific driver is not built-in:
drivers/built-in.o: In function `omap2430_musb_disable':
usb/musb/omap2430.c:480: undefined reference to `omap_control_usb_set_mode'
drivers/built-in.o: In function `omap2430_musb_enable':
usb/musb/omap2430.c:466: undefined reference to `omap_control_usb_set_mode'
usb/musb/omap2430.c:447: undefined reference to `omap_control_usb_set_mode'
drivers/built-in.o: In function `omap_musb_set_mailbox':
usb/musb/omap2430.c:273: undefined reference to `omap_control_usb_set_mode'
usb/musb/omap2430.c:304: undefined reference to `omap_control_usb_set_mode'
drivers/built-in.o:(.debug_addr+0xbd9e0): more undefined references to `omap_control_usb_set_mode' follow
This adds an explicit dependency.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: ca784be36c ("usb: start using the control module driver")
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: Felipe Balbi <balbi@ti.com>
Multiple musb glue drivers depend on the generic usb phy support,
but fail to list it as a dependency in Kconfig. This results
in build erros like:
drivers/built-in.o: In function `am35x_remove':
:(.text+0xadacc): undefined reference to `usb_phy_generic_unregister'
drivers/built-in.o: In function `am35x_probe':
:(.text+0xae1c8): undefined reference to `usb_phy_generic_register'
:(.text+0xae244): undefined reference to `usb_phy_generic_unregister'
drivers/built-in.o: In function `jz4740_remove':
:(.text+0xaf648): undefined reference to `usb_phy_generic_unregister'
drivers/built-in.o: In function `jz4740_musb_init':
:(.text+0xaf694): undefined reference to `usb_phy_generic_register'
This adds the ones that are missing.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Delete private selfpowered variable, and use common one.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Delete private selfpowered variable, and use common one.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Delete private selfpowered variable, and use common one.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Delete private selfpowered variable, and use common one.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
fsl udc core assumes itself always self powered, so set is_selfpowered
is 1.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Delete private selfpowered variable, and use common one.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Delete private selfpowered variable, and use common one.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The gadget power property will be used at get_status request.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit 8e74475b0e (usb: dwc3: gadget: use udc-core's
reset notifier) added support for the new UDC core's
reset notifier to dwc3 but while at it, it removed
a spin_lock() from dwc3_reset_gadget() which might
cause an unbalanced spin_unlock() further down the line
Fixes: 8e74475b0e (usb: dwc3: gadget: use udc-core's reset notifier)
Cc: <stable@vger.kernel.org> # v3.19
Signed-off-by: Felipe Balbi <balbi@ti.com>
Sometimes we want to just print a formatted
string without passing any extra data. The
following will be used for removing reliance
on dev_vdbg() from dwc3.
Signed-off-by: Felipe Balbi <balbi@ti.com>
if an unknown IRQ event is triggered, that means
the HW is really misbehaving. Instead of printing
a debug message, let's WARN() so users report
when that happens.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The purpose of the functions and their parametrs might not be obvious
to the reader, so explain it.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The first parameter of __uvcg_iter_strm_cls() is always used in
the context of struct uvcg_streaming_header, so change the
function prototype accordingly.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is a request from IC engineer that if we doesn't
set phypwd as 0xffffffff, we need to delay about five
32Khz cycles before set phy's pwd register, otherwise,
the wakeup signal may can't wake up controller.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
At very rare cases, the SoF will not send out after resume with
low speed connection. The workaround is do not power down
PWD.RXPWD1PT1 bit during the suspend.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
For non-otg mode, we keep the usage of disconnect line between phy analog
and digital unchanging; for otg mode, at peripheral role, we keep the usage
unchanging too, at host role, the digital part needs to know dp/dm change
to respond device's data pulse when it is at low power mode.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <b47624@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The RLT code has already done it, so no software operation is needed.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The isp1760 driver registration function returns an error if USB is
disabled. This made sense when the driver only supported host
controllers, but now that it supports peripheral controllers host
support isn't mandatory anymore.
Fix this by returning an error only when both the HCD and UDC functions
are disabled, either through the kernel configuration or at runtime.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Both isp1760_register() and isp1761_pci_probe() check whether USB is
disabled by calling usb_disabled(), and bail out with an error if it is.
One check is enough, remove the PCI-specific check.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Enable compilation of the isp1760 driver in pure host mode, pure device
mode, or dual-role mode.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Now that this is DRD, it doesn't make sense to keep it under
drivers/usb/host.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The ISP1761 is a dual-mode host and device controller backward
compatible on the host side with the ISP1760. Add support for the device
controller.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Configuring the mode of operation of port 1 doesn't belong to the HCD
code, as it's related to the soon to come UDC support. Move the
configuration to core code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Although the corresponding register is part of the HCD register space,
processor bus initialization is not specific to the HCD. To prepare for
device controller support, move bus interface initialization to core
code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The IRQF_SHARED flag needs to be set regardless of the bus type. Don't
require glue code to set it manually.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Move core device initialization to a central location in order to share
it with the device mode implementation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The isp1760-rhcd.h header contains PTD constants and structures only
useful for the HCD implementation. It also contains register definitions
that will be needed by common code when implementing support for the
ISP1761 device controller, but doesn't contain the isp1760_hcd structure
definition that will also be used by common code.
Move definitions to the right location and create an isp1760-regs.h to
store register definitions. No change other than moving definitions and
modifying indentation is performed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The slotinfo and memory_chunk structures are specific to the driver and
defined in a header file. Prefix them with isp1760_ to avoid namespace
clashes.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate the driver private data structure manually instead of using the
usb_hcd private space. This will allow skipping hcd registration for the
isp1761 when used in device mode only.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Move the initialization code out of the PCI probe function to a new
function in order to simplify and fix error handling.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This simplifies error and remove code paths.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The function takes quite a few arguments, passing the resource pointer
instead of the start address and length simplifies it a bit.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The argument is unused, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The two functions are specific to the driver but have very generic
names, subject to collisions. Rename them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The glue code probe functions don't need to access the hcd structure
anymore. Modify isp1760_register to return an integer error code instead
of the hcd pointer.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The removal cleanup code is duplicated between the different bus glues.
Move it to a central location.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The I/O registers are mapped in the HCD code but must be unmapped by
glue code. The OF and PCI glue code unmap them correctly but the
platform glue code is missing an iounmap() call. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The platform driver remove function needs to release the memory resource
requested at probe time. Instead of retrieving the resource from the
platform device, retrieve it from the usb_hcd. This mimics the behaviour
of the PCI and OF glues, and will make it easier to share code between
all three glue layers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The structure is allocated for the sole purpose of holding a pointer to
the HCD and being stored in platform device driver data. Store the HCD
pointer directly instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Switching to the managed gpio descriptor API simplifies both error and
cleanup code paths (by removing the need to free the gpio) and runtime
code (by removing manual handling of the active low flag). It also
permits handling the reset gpio entirely from within the HCD code,
sharing it between the different glue layers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fixed the following warnings (reported by cppcheck):
[drivers/usb/gadget/function/f_sourcesink.c:1217]: (warning) %d in format string (no. 1)
requires 'int' but the argument type is 'unsigned int'.
[drivers/usb/gadget/function/f_sourcesink.c:1261]: (warning) %d in format string (no. 1)
requires 'int' but the argument type is 'unsigned int'.
[drivers/usb/gadget/function/f_sourcesink.c:1305]: (warning) %d in format string (no. 1)
requires 'int' but the argument type is 'unsigned int'.
[drivers/usb/gadget/function/f_sourcesink.c:1349]: (warning) %d in format string (no. 1)
requires 'int' but the argument type is 'unsigned int'.
[drivers/usb/gadget/function/f_sourcesink.c:1393]: (warning) %d in format string (no. 1)
requires 'int' but the argument type is 'unsigned int'.
[drivers/usb/gadget/function/f_sourcesink.c:1437]: (warning) %d in format string (no. 1)
requires 'int' but the argument type is 'unsigned int'.
[drivers/usb/gadget/function/f_sourcesink.c:1476]: (warning) %d in format string (no. 1)
requires 'int' but the argument type is 'unsigned int'.
[drivers/usb/gadget/function/f_sourcesink.c:1520]: (warning) %d in format string (no. 1)
requires 'int' but the argument type is 'unsigned int'.
[drivers/usb/gadget/function/f_sourcesink.c:1564]: (warning) %d in format string (no. 1)
requires 'int' but the argument type is 'unsigned int'.
[drivers/usb/gadget/function/f_sourcesink.c:1608]: (warning) %d in format string (no. 1)
requires 'int' but the argument type is 'unsigned int'
Reviewed-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Asaf Vertz <asaf.vertz@tandemg.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add eventfd which notifies userspace about ep0 events and AIO completion
events. It simplifies using of FunctionFS with event loop, because now
we need to poll on single file (instead of polling on ep0 and eventfd's
supplied to AIO layer).
FunctionFS eventfd is not triggered if another eventfd is supplied to
AIO layer (in AIO request). It can be useful, for example, when we want
to handle AIO transations for chosen endpoint in separate thread.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use if-loop variable 'epfile' instead of start variable 'epfiles'. Now the
correct endpoint file name is stored.
Signed-off-by: Mario Schuknecht <mario.schuknecht@dresearch-fe.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
USB vendor type is encoded in field bmRequestType. Make test USB_TYPE_VENDOR
with bRequestType instead of bRequest.
Signed-off-by: Mario Schuknecht <mario.schuknecht@dresearch-fe.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
1. set AUTOREQ to NONE at the beginning of teardown;
2. add delay for dma pipeline to drain;
3. Do not set USB_TDOWN bit for RX teardown.
The CPPI hw has an issue that when tearing down a RX channel, if
another RX channel is receiving data, the CPPI will lockup.
To workaround the issue, do not set the CPPI TD bit. The steps before
this point ensures the CPPI channel will be torn down properly.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The macro EP_MODE_AUTOREG_* should be called EP_MODE_AUTOREQ_*, as they
are used for register AUTOREQ.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
To add support for requesting DT DMA in the future, this patch adds
usbhsf_dma_init_pdev() function.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix using the bare number to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix using the bare numbers to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Just two fixes pending. A fix USB PHY for non-OF case and
a fix for dwc2 running on samsung SoC.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJUwVBYAAoJEIaOsuA1yqREZwwP/0/uE+dullOFcv5Yg4624INb
2GnQznXmp6NLa+y7262akEAaIYprnVMU3Dpo66+rrl01S71cAtYYC2VBct8f2fvk
o6ufSOWgsvj7D+6HUFivw9DYFx/Kk5RHG+pz69/TiLmbZBGU2R0+6QZdrcz7hD15
5oykD793DkLP5rRC71vQiGhMIKOEWvGlD4sHtJd9SazE96Txi5f9a09mFA1ORLbi
9eEcPEjEc52rHeQToKYU+xi5Sf3ifql1gITNeQiWTu7+CIMFpx9mymo2S6yaSp+d
GhzUtiX5w9IlPZ4fS235KcsILdiycOIFfO0Z7IHRYUq9Vms+Dwu6TO2aHG7ap1xF
st3jA0svlZwEHIoGcp7LYaNIadSsrluYeXsY6jOfpzfwwaa51XIJbGFdGkVcMTf2
pZd/+Q+3UxAhPxk1/Btyd+2KMhhYGd8b8ol1BZDos+MzBCO3JZcakGA0wH2UuNcU
IXM6TbUI9waoZD9Jp5fMYC64xdWvluPis8ag/ay1u+tsAPumdQXb1fiNeJvjDvN+
x7qSv/QQfq3VEn0K3TROZM+7qEu9/LU7PNS+Q+aE5FxNE7IZ/WtJHUyOVsxybI4P
ChSr+Jqh9Q10x+s+ChwjLOQSNrQxnX8Dq4GnglUesf8xhZF84jtghlCLaAla+3yf
LzMKhudkzP1xjDDnfl/R
=QdcU
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v3.19-rc6
Just two fixes pending. A fix USB PHY for non-OF case and
a fix for dwc2 running on samsung SoC.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Added the USB serial console device ID for Siemens Ruggedcom devices
which have a USB port for their serial console.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
OTG device shall support this device for allowing compliance automated testing.
The modification is derived from Pavankumar and Vijayavardhans' previous work.
Signed-off-by: Macpaul Lin <macpaul@gmail.com>
Cc: Pavankumar Kondeti <pkondeti@codeaurora.org>
Cc: Vijayavardhan Vennapusa <vvreddy@codeaurora.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like some other uas devices these devices hang when a report-opcodes scsi
command is send to them.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1124119
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I recently posted a patch ("storage: Add quirk for another SCM-based
USB-SCSI converter") to add a quirk for the converter with ID 04E6:000F,
which is listed along with 04E6:000B in the Windows INF file for the
Startech ICUSBSCSI2 as "eUSB SCSI Adapter (Bus Powered)".
The already-present quirk for 04E6:000B has USB_SC_SCSI/USB_PR_BULK, not
USB_SC_DEVICE/USB_PR_DEVICE. Change the 04E6:000F quirk to match that,
since it will probably be required.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device needs to be continuously clocked to provide wake up support,
previously, if STANDBY target were chosen the device were
enable_irq_wake()-prepared and clock still active and if MEM target were
chosen the device were also enable_irq_wake()-prepared but not clocked
anymore, which is wrong.
Now, if STANDBY target is chosen the device is still clocked with wake
up support enabled, which were the previous default and if MEM target is
chosen the device is declocked with wake up support disabled.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch move AT91 OHCI global variables (clocks ptr and clocked
boolean) to private struct ohci_at91_priv, stored in ohci->priv.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch move Atmel EHCI global variables (clocks ptr and clocked
boolean) to private struct atmel_ehci_priv, stored in ehci->priv.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replace struct platform_driver.{resume,suspend} PM bindings
to a new struct dev_pm_ops.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch add suspend/resume support for Atmel EHCI, mostly
about disabling and unpreparing clocks so USB PLL is stopped
before entering sleep state.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently if port power is turned off by user on hub port
using USBDEVFS then port power is turned back ON
by hub driver.
This commit modifies hub reset logic in hub_port_connect() to prevent
hub driver from turning back the port power ON if port is not owned
by kernel.
Signed-off-by: Deepak Das <deepakdas.linux@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added support for cases where one controller is connected
to multiple phys.
Signed-off-by: Arun Ramamurthy <arunrama@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Tested-by: Scott Branden <sbranden@broadcom.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added support for cases where one controller is connected
to multiple phys
Signed-off-by: Arun Ramamurthy <arunrama@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Tested-by: Scott Branden <sbranden@broadcom.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare numbers to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare number to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Valentina Manea <valentina.manea.m@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare number to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare numbers to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare numbers to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare number to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare numbers to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare numbers to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare number to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare numbers to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare numbers to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
While at it, stop setting already set HUB_CHAR_INDV_PORT_LPSM once again.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare numbers to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
While at it, fix the indentation.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare numbers to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
While at it, stop setting already set HUB_CHAR_INDV_PORT_LPSM once again.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare number to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare numbers to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare numbers to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
While at it, avoid duplicate computation when calling DBG().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare number to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare numbers to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare numbers to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare numbers to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare number to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare numbers to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When re-applying the configuration after a successful usb device reset,
xhci_discover_or_reset_device has already dropped the endpoints, and free-ed
the rings.
The endpoints already being dropped is expected, and should not lead to
warnings. Use the fact that the rings are also free-ed in this scenario to
detect this, and suppress the "xHCI xhci_drop_endpoint called with disabled
ep ..." message in this case.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
--
Changes in v2:
Move the ring check to only guard the xhci_warn, so as to avoid side-effects
in case we have a scenario where the rings are free-ed, but the endpoint is
not yet dropped.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To help debugging xhci problems.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB stack provides a mechanism for drivers to request an
asynchronous device reset (usb_queue_reset_device()). The mechanism
uses a work item (reset_ws) embedded in the usb_interface structure
used by the driver, and the reset is carried out by a work queue
routine.
The asynchronous reset can race with driver unbinding. When this
happens, we try to cancel the queued reset before unbinding the
driver, on the theory that the driver won't care about any resets once
it is unbound.
However, thanks to the fact that lockdep now tracks work queue
accesses, this can provoke a lockdep warning in situations where the
device reset causes another interface's driver to be unbound; see
http://marc.info/?l=linux-usb&m=141893165203776&w=2
for an example. The reason is that the work routine for reset_ws in
one interface calls cancel_queued_work() for the reset_ws in another
interface. Lockdep thinks this might lead to a work routine trying to
cancel itself. The simplest solution is not to cancel queued resets
when unbinding drivers.
This means we now need to acquire a reference to the usb_interface
when queuing a reset_ws work item and to drop the reference when the
work routine finishes. We also need to make sure that the
usb_interface structure doesn't outlive its parent usb_device; this
means acquiring and dropping a reference when the interface is created
and destroyed.
In addition, cancelling a queued reset can fail (if the device is in
the middle of an earlier reset), and this can cause usb_reset_device()
to try to rebind an interface that has been deallocated (see
http://marc.info/?l=linux-usb&m=142175717016628&w=2 for details).
Acquiring the extra references prevents this failure.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Russell King - ARM Linux <linux@arm.linux.org.uk>
Reported-by: Olivier Sobrie <olivier@sobrie.be>
Tested-by: Olivier Sobrie <olivier@sobrie.be>
Cc: stable <stable@vger.kernel.org> # 3.19
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ehci-octeon driver used a 64-bit dma_mask. With removal of ehci-octeon
and usage of ehci-platform ehci dma_mask is now limited to 32 bits
(coerced in ehci_platform_probe).
Provide a flag in ehci platform data to allow use of 64 bits for
dma_mask.
Cc: David Daney <david.daney@cavium.com>
Cc: Alex Smith <alex.smith@imgtec.com>
Signed-off-by: Andreas Herrmann <andreas.herrmann@caviumnetworks.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'len' variable in fhci_hub_control() is write-only, so totally useless.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code handling Get Hub Descriptor request copies data from root_hub_des[],
then overwrites byte 3 with real 'wHubCharacteristics' value. There's no need
to overwrite, we can substitute the real value right into root_hub_des[3].
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare numbers to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix using the bare number to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
__uvcg_fill_strm() called from __uvcg_iter_stream_cls()
might have advanced the "data" even if __uvcg_iter_stream_cls()
returns an error, so use a backup copy as an argument to kfree().
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This reverts commit 0cf884e819.
Even after applying the follow-on patch at
https://patchwork.kernel.org/patch/5325111
there are still problems with device connect on the Altera SOCFPGA
platform at least. One possible fix would be to add a whitelist
to enable suspend/resume on platforms where it does work correctly.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Instead of custom approach the patch converts code to use %pM specifier to
print MAC.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The use of GPIOs should be optional for the generic phy, otherwise
the Altera SOCFPGA platform at least is broken.
Fixes breakage caused by a combination of e9f2cefb0c "usb: phy:
generic: migrate to gpio_desc" and 135b3c4304 "usb: dwc2: platform:
add generic PHY framework support".
Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
1) Change "conv" an "vnoc" to "to_cpu_endian" to "to_little_endian".
2) No need to check the "limit" because that is already handled in
kstrtoXX so delete that parameter along with the check.
3) By using a "bits" parameter, we can combine the "uxx" parameter and
the "str2u" parameters.
4) The kstrtou##bits() conversion does not need to be done under the
mutex so move it to the start of the function.
5) Change the name of "identity_conv" to "noop_conversion".
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We need to add a kfree(h) on an error path.
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
"num" is a u32 so "(num > 0xFFFFFFFF)" is never true. Also the range
is already checked in kstrtou32().
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In practice failure to find phy when requested in non-OF
case means it will never become available, so
__usb_find_phy() must return -ENODEV and not -EPROBE_DEFER.
This fixes a regression caused by commit 9c9d82492b
(usb: phy: Fix deferred probing), where the USB
controller driver is left infinitely into deferred probe
when there are no phys.
Fixes: 9c9d82492b (usb: phy: Fix deferred probing)
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We're basically saying ERR_CAST(NULL) and PTR_ERR(NULL) here, which is
nonsensical.
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes the following problem: data transmission in direction
IN break unless the GSNPSID register access is done with spinlock held.
This issue occurs at least in Exynos4412 SoC, probably in many SoC's
from Exynos familly.
The problem is described here:
https://lkml.org/lkml/2014/12/22/185
And there is linux mailing list discussion:
https://lkml.org/lkml/2015/1/14/17
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is old, unused code that is #defined out by the use of NOTMOS7840
and NOTMCS7840 - these are not defined anywhere.
If NOTMOS7840 is defined then the code will break on null pointer
dereferences on mos7840_port. So the code is currently unused, and
broken anyway, so why not just remove it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
While the code is correct and functions well, it's still
a bit misleading to add the reference operator in from of
the buf argument.
This patch simply removes that operator in order to make
use of buf slightly better to the eyes.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since we can compose gadgets from many functions, there is the problem
related to gadget breakage while FunctionFS daemon being closed. FFS
function is userspace code so there is no way to know when it will close
files (it doesn't matter what is the reason of this situation, it can
be daemon logic, program breakage, process kill or any other). So when
we have another function in gadget which, for example, sends some amount
of data, does some software update or implements some real-time functionality,
we may want to keep the gadget connected despite FFS function is no longer
functional.
We can't just remove one of functions from gadget since it has been
enumerated, so the only way to keep entire gadget working is to make
broken FFS function deactivated but still visible to host. For this
purpose this patch introduces "no_disconnect" mode. It can be enabled
by setting mount option "no_disconnect=1", and results with defering
function disconnect to the moment of reopen ep0 file or filesystem
unmount. After closing all endpoint files, FunctionFS is set to state
FFS_DEACTIVATED.
When ffs->state == FFS_DEACTIVATED:
- function is still bound and visible to host,
- setup requests are automatically stalled,
- transfers on other endpoints are refused,
- epfiles, except ep0, are deleted from the filesystem,
- opening ep0 causes the function to be closed, and then FunctionFS
is ready for descriptors and string write,
- altsetting change causes the function to be closed - we want to keep
function alive until another functions are potentialy used, altsetting
change means that another configuration is being selected or USB cable
was unplugged, which indicates that we don't need to stay longer in
FFS_DEACTIVATED state
- unmounting of the FunctionFS instance causes the function to be closed.
Tested-by: David Cohen <david.a.cohen@linux.intel.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Removing a few items that are not needed anymore and
adding separate function for quirks.
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is nothing specific being done in the suspend and
resume callbacks that is not already taken care of in PCI
driver core, so dropping the functions.
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
None of the PCI platforms need the NOP transceivers, and
since we can now live without the PHYs, removing
registration of the platform devices for them.
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
drivers/usb/gadget/function/uvc_configfs.c:46:28: sparse: symbol 'to_uvcg_control_header' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:138:25: sparse: symbol 'uvcg_control_header_type' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:164:6: sparse: symbol 'uvcg_control_header_drop' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:721:20: sparse: symbol 'to_uvcg_format' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:798:30: sparse: symbol 'to_uvcg_streaming_header' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:950:25: sparse: symbol 'uvcg_streaming_header_type' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:976:6: sparse: symbol 'uvcg_streaming_header_drop' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:1020:19: sparse: symbol 'to_uvcg_frame' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:1265:25: sparse: symbol 'uvcg_frame_type' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:1315:6: sparse: symbol 'uvcg_frame_drop' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:1338:26: sparse: symbol 'to_uvcg_uncompressed' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:1548:25: sparse: symbol 'uvcg_uncompressed_type' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:1586:6: sparse: symbol 'uvcg_uncompressed_drop' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:1610:19: sparse: symbol 'to_uvcg_mjpeg' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:1761:25: sparse: symbol 'uvcg_mjpeg_type' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:1793:6: sparse: symbol 'uvcg_mjpeg_drop' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since we call gaudio_cleanup at f_audio_free, the f_uac1_opts
doesn't need to use gaudio any more.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate udc structure instead of relying on the statically declared
object.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
cpu_is_at91xxx are a set of macros defined in mach/cpu.h and are here used
to detect the SoC we are booting on.
Use compatible string + a caps structure to replace those cpu_is_xxx tests.
Remove all mach and asm headers (which are now unused).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Make use of devm_ functions to simplify probe and remove code.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Since non-DT board support has been removed from the at91 architecture we
can safely remove non-DT handling code.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Now that at91 system clocks forward set_rate request to their parent we
can remove the uclk clock and directly call clk_set_rate on fclk.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The driver is requesting clock by their global name (those declared in the
clk_lookup list), but this only works with !CCF kernels.
Now that all SoCs have moved to CCF, fix the driver to use local names
(hclk and pclk).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The final set of fixes for v3.19. Two of the fixes are
related to dwc3 scatter/gather implementation when we have
more requests queued than available TRBs, while the other
is a build fix for mv-usb PHY.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=iLKs
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v3.19-rc6
The final set of fixes for v3.19. Two of the fixes are
related to dwc3 scatter/gather implementation when we have
more requests queued than available TRBs, while the other
is a build fix for mv-usb PHY.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Here are a few fixes for reported problems including a possible
null-deref on probe with keyspan, a misbehaving modem, and a couple of
issues with the USB console.
Some new device IDs are also added.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=umHr
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v3.18-rc5
Here are a few fixes for reported problems including a possible
null-deref on probe with keyspan, a misbehaving modem, and a couple of
issues with the USB console.
Some new device IDs are also added.
Signed-off-by: Johan Hovold <johan@kernel.org>
DWC3 gadget sets up a pool of 32 TRBs for each EP during initialization. This
means, the max TRBs that can be submitted for an EP is fixed to 32. Since the
request queue for an EP is a linked list, any number of requests can be queued
to it by the gadget layer. However, the dwc3 driver must not submit TRBs more
than the pool it has created for. This limit wasn't respected when SG was used
resulting in submitting more than the max TRBs, eventually leading to
non-transfer of the TRBs submitted over the max limit.
Root cause:
When SG is used, there are two loops iterating to prepare TRBs:
- Outer loop over the request_list
- Inner loop over the SG list
The code was missing break to get out of the outer loop.
Fixes: eeb720fb21 (usb: dwc3: gadget: add support for SG lists)
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When scatter gather (SG) is used, multiple TRBs are prepared from one DWC3
request (dwc3_request). So while preparing TRBs, the 'last' flag should be set
only when it is the last TRB being prepared from the last dwc3_request entry.
The current implementation uses list_is_last to check if the dwc3_request is the
last entry from the request_list. However, list_is_last returns false for the
last entry too. This is because, while preparing the first TRB from a request,
the function dwc3_prepare_one_trb modifies the request's next and prev pointers
while moving the URB to req_queued. Hence, list_is_last always returns false no
matter what.
The correct way is not to access the modified pointers of dwc3_request but to
use list_empty macro instead.
Fixes: e5ba5ec833 (usb: dwc3: gadget: fix scatter gather implementation)
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: Felipe Balbi <balbi@ti.com>
The driver was recently adapted to a core API change, but the
change was incomplete, missing out the suspend helper and
leaving an extraneous local variable around:
usb/phy/phy-mv-usb.c: In function 'mv_otg_update_state':
usb/phy/phy-mv-usb.c:341:18: warning: unused variable 'phy' [-Wunused-variable]
usb/phy/phy-mv-usb.c: In function 'mv_otg_suspend':
usb/phy/phy-mv-usb.c:861:16: error: 'struct usb_phy' has no member named 'state'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: e47d92545c ("usb: move the OTG state from the USB PHY to the OTG structure")
Signed-off-by: Felipe Balbi <balbi@ti.com>
On the Renesas R8A7791 SoC based boards there's MAX3355 USB OTG chip and mini-AB
USB connector corresponding to USB port 0 driven either by EHCI/OHCI or Renesas
USBHS gadget controller. And we'd like the host/gadget drivers to work based on
the cable type connected. An 'extcon' driver for MAX3355 has been written, so we
only need to bind to it via device tree which I'm doing in this patch.
(Perhaps, it would also make sense to use OTG HNP when the USBHS host mode is
active and a B-cable is connected but I don't have access to host-capable USBHS,
so wouldn't be able to test it.)
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If usb bus is reset without a physical disconnection, all endpoints
will remain open. Call s3c_hsotg_disconnect() from reset handler to
report a disconnect to gadget framework. hsotg->connected is checked
in s3c_hsotg_disconnect() before processing disconnect.
In some cases, USBRst is seen before EnumDone and after it as well.
So move setting of hsotg->connected to set-address to avoid reporting
extra disconnection in this case.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When booting with id pin grounded, dwc2 default to host mode.
Thus, force device mode prior initializing gadget part.
Else fifo init will fail since fifo values are not correct
in host mode.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This callback informs the driver about the total amount of current it
is allowed to draw. Share this information with the phy so that
current limits can be set for charging for example.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Gadget must be informed about disconnection when pullup is
removed.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
After all endpoints are disabled, fifo_map should have reached 0.
Its a bug if if didn't, so warn about it and reset it to 0 so that
driver can continue using all the fifos.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When selecting different alt setting, s3c_hsotg_ep_enable can be
called with fifo already allocated. Allocate fifo again only if
required and after deallocating the previous fifo.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Current algorithm picks the first fifo which is equal to or greater
than the required size. This can result in bigger fifos assigned to
endpoints with smaller maxps. Change the algorithm to pick the
smallest fifo which is greater than or equal to the required size.
Moreover, only use signed variables when required.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This flag is set before sending the zlp. So use present tense instead
of the past tense.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Enable phy driver to report vbus session. This allows us to remove
D+ pullup when vbus is not present.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Can't stay in the loop forever. Break it after timeout.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The warning is probably good but it has false positives in both dma and non-dma
cases. So its not very helpful in either.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
According to programming guide, zero length packet should be
programmed on its own and should not be counted in DIEPTSIZ.PktCnt
with other packets.
For ep0, this is the zlp for DATA IN stage (if required) and not for
the STATUS stage.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Manage ep0 state in software to add handling of status OUT stage.
Just toggling hsotg->setup in s3c_hsotg_handle_outdone leaves it in
wrong state in 2-stage control transfers.
Moreover, ensure that for setup-packet s3c_hsotg_handle_outdone is
called either from SetupDone or OutDone but not both. Dwc2 ip v3.00a
generates both SetupDone and OutDone on setup packets.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
kill_all_requests() can flush the fifo. Call it after disabling the
endpoint.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When matching tx fifo to endpoint, consider all fifos instead of
hard limiting to 8
Moreover, print error in case no fifo could be found.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
< 15 check doesn't show debug information for endpoint 15.
It is possible to have less than 15 endpoints so use limit
provided by hardware configuration.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
These members are only occupying space.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As fifo size can vary between SOCs, add possibility to configure
them from device tree. Fifo sizes used by the legacy driver will
be used If they are not provided by the device tree.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Reviewed-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Current code does not check endpoint 15 interrupt. Use number
of endpoint configured in hardware instead of the hardcoded value.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
GHWCFG1 provides hardware configuration of each endpoint. Use
it to configure the endpoints instead of assuming all even
endpoint are OUT and all odd endpoints are IN.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
* Add an of specific function to parse device node properties.
* Enable dma usage only if device tree property 'g_use_dma' is present.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Do a read-modify-write instead of only setting DMAEn bit.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
HBstLen is GAHBCFG[4:1]. Use GAHBCFG_HBSTLEN_SHIFT to write burst-
length at correct position.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In the error path, s3c_hsotg_phy_disable should be called after a
call to s3c_hsotg_phy_enable is made.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When using DMA, data of the previous setup packet can be read back
from cache because ep0 and ctrl buffers are embedded in struct s3c_hsotg.
Allocate buffers instead of embedding them.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Reviewed-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Only process DOEPINT.XferCompl on data packet as DOEPINTn.SetUp can
occur with or without DOEPINT.XferCompl. When DOEPINT.SetUp occurs
with DOEPINT.XferCompl, only DOEPINT.SetUp needs to be handled.
Moreover, ignore DOEPINT.XferCompl when it occurs with
DOEPINT.StupPktRcvd as driver needs to wait for DOEPINT.SetUp to
continue.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When using DMA, keep fifo empty interrupt disabled. Otherwise
core is flooded by interrupts.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Bind peripheral controller to the phy on udc_start. Unbind on
udc_stop.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Just three fixes this time. An oops fix in ep_write() from gadgetfs,
another oops for the Atmel UDC when unloading a gadget driver and
the fix for PHY deferred probing.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7Fj7
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v3.19-rc5
Just three fixes this time. An oops fix in ep_write() from gadgetfs,
another oops for the Atmel UDC when unloading a gadget driver and
the fix for PHY deferred probing.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Conflicts:
drivers/usb/phy/phy.c
UDC core has already done it before .udc_stop and after .udc_start.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
UDC core has already done it before .udc_stop and after .udc_start.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Instead of using variable length array, use a static length equal to
the size of the ffs->ev.types array. This gets rid of a sparse warning:
drivers/usb/gadget/function/f_fs.c:401:44: warning:
Variable length array is used.
and makes it more explicit that the array has a very tight upper size
limit. Also add some more documentation about the ev.types array and
how its size is limited and affects the rest of the code.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: Rohith Seelaboyina <rseelaboyina@nvidia.com>
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add support for vbus detection and power supply. This code is more or
less stolen from phy-gpio-vbus-usb.c, and aims at providing a detection
mechanism for VBus (ie. usb cable plug) based on a GPIO line, and a
power supply activation which draws current from the VBus.
[ balbi@ti.com : fix build break ]
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Change internal gpio handling from integer gpios into gpio
descriptors. This change only addresses the internal API and
device-tree/ACPI, while the legacy platform data remains integer space
based.
This change is only build compile tested, and very prone to error. I
leave this comment for now in the commit message so that this patch gets
some testing as I'm pretty sure it's buggy.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Cache INT_ENB register value in order to avoid uncached iomem access, and
thus improve access time to INT_ENB value.
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Avoid interpreting useless status flags when we're not waiting for such
events by masking the status variable with the interrupt enabled register
value.
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Reported-by: Patrice VILCHEZ <patrice.vilchez@atmel.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
at91sam9g45 and at91sam9x5 SoCs have an hardware bug forcing us to
generate a pulse on the BIAS signal on "USB end of reset” and
“USB end of resume" events.
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Reported-by: Patrice VILCHEZ <patrice.vilchez@atmel.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
at91sam9rl SoC has an erratum forcing us to toggle the BIAS on USB
suspend/resume events.
This specific handling is only activated when CONFIG_ARCH_AT91SAM9RL is
set and this option is only set when building a non-DT kernel, which is
problematic since non-DT support for at91sam9rl SoC has been removed.
Rework the toggle_bias implementation to attach it to the "at91sam9rl-udc"
compatible string.
Add new compatible strings to avoid executing at91sam9rl erratum handling
on other SoCs.
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Removes some functions that are not used anywhere:
fsl_otg_tick_timer() view_ulpi()
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Felipe Balbi <balbi@ti.com>
For some user cases, like plug out and replug in usb device during
the system suspend, the speed negotiation will be error due to host
doesn't know the device's disconnection, and it still hopes the
high speed device, but the device backs to "powered" state which
its high speed termination is not enabled, the usb core calls
the PHY's disconnect notifier with "full speed", it will NOT
take effect at all.
If the usb core calls disconnect notifer, the port change must happen,
so it is safe to disable high speed disconenct detector, since
connect notifier will be called soon if the device is still connected
on the port, and we will enable high speed disconnect detector at that
time.
Acked-by: Li Jun <b47624@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When we shut down the PHY, we need to power down all PHY's functions
as well as disable wakeup, it is the opposite operation we do at .init.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes in simpler way the bug described in [1] and [2]. It
looks like DWC2 is the only UDC driver that doesn't force usb requests
to complete in ep_disable() function. This causes described problem,
because we have no guarantee that all requests will be completed before
unbind of usb function.
To fix this problem we force all requests of disabled endpoint to complete.
Also currently running request is not handled. This allowed to simplify
code of kill_all_requests() function, because 'force' parameter is always
set to true, so we don't need it anymore.
In s3c_hsotg_rx_data() we change function used to print message when active
request is NULL from dev_warn() to dev_dbg(), because such situation is
harmless for driver and now it can take place during normal endpoint
disabling.
[1] https://lkml.org/lkml/2014/12/9/283
[2] https://lkml.org/lkml/2014/12/12/360
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some debug messages were not build due to unconditional #if 0.
These messages are very useful for debugging and the user can enable
them on demand via dynamic debug.
If they are not enabled the performance is not affected.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
ASSERT_OUT_NAKING was only called by out_flush and was hidden behind a
ifdef.
This patch moves the inline function into out_flush and remove the
ifdef. The user can decide to print the debug message or not via dynamic
printk
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
After fix superspeed dma_done was applied we can simplify the code by
removing the duplicated dma_done and letting the function check if there
are more completed dma transactions.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The function is very simple, does not declare any variable and it is
called in the irq path.
The counterpart for net228x is already declared as inline.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Function resume_dma is not used, remove it.
The reason the compiler did not catch this dead code is the inline
modifier.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Once the defect 7374 is patched, there is no reason the keep reading the
idx scratch register.
Cache the content of the scratch idx register on device flag.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Do not duplicate the code for the else branch of the condition.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We can use the same function for both families of chips and also remove
the ep_stop_dma() function.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
irqs_superspeed calls ep_stall instead of set/clear_halt, due to a
workaround for SS seqnum. Create a function with the workaround and
call set/clear_halt instead.
This way we can compare the code of super/normal speed and it is easier
to follow the code.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Field is_halt is never used by any function.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
ep_stdrsp was only called by handle_stat0_irqs_superspeed and with
always the same flags.
Remove the function and replace the call by the code inside the
function, since it is very simple once the dead code is removed.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
restart_dma is not used before it is declaration. Therefore we can
remove this definition.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove dma_started field from net2280_ep structure, since it is not used
by any function.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
use_dma parameter was designed to enable the dma on the chip. It was
enabled by default.
It comes from the time when the dma was not reliable. Now it has been
working ok in production.
This patch removes this parameter.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Parameter use_msi was used to enable msi irq on usb338x chips, it was
enabled by default.
There is no reason to prefer non-msi irq on usb338x, and it falls back
to non msi on error.
Therefore remove this option.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch removes the full_speed parameter used force full-speed
operation.
It was designed exclusively for testing purposes, and there is no
reason to maintain this in a production kernel.
Reverts: 2f07607747
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
use_dma_chaining module parameter was designed to avoid creating one irq
per package on a group of packages (with the help of the driver's flag
no_interrupt).
Unfortunately, when this parameter is enabled, the driver fails to work
on both net2280 and 3380 chips.
This patch removes this parameter, which was disabled by default.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is a typo ("prove" instead of "probe") in the error message printed when
the platform initialization fails. Replace that word with more fitting "init".
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
fixups for incorrect use of DECLARE_COMPLETION. see also commit
6e9a4738 ("completions: lockdep annotate on stack completions")
patch is against 3.18.0 linux-next
This was only code reviewed and compile tested
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Update this according to USB Audio Class 1.0 spec. This fixes the Windows 7
detection issue.
Cc: Rafael Brune <mail@rbrune.de>
Signed-off-by: Xuebing Wang <xbing6@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
(Fixed some code style issues)
Tested-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
UAC1 forget to do it.
Signed-off-by: Xuebing Wang <xbing6@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
"ep" isn't NULL here, and static checkers complain because we
dereferenced it on the previous line.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We already know what "value" is, so there is no need to check. It
puzzles static checkers to have the unneeded condition.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Get PHY parameters from devicetree and power off usb PHY during
system suspend.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add support for using the uvc function as a component of USB gadgets composed
with configfs.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
