Adjust driver behavior during FW boot. Proper sequence of
events after reset and FW download, is as following:
- FW prepares mailbox structure and reports IRQ "FW_READY"
- driver caches mailbox registers, marks mailbox readiness
- FW sends WMI_FW_READY event, ignore it
- FW sends WMI_READY event with some data
- driver stores relevant data marks FW is operational
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When Tx ring full is encountered with TSO,
printout of "DMA error" was wrongly printed.
In addition, in case of Tx ring full return
proper error code so that NETDEV_TX_BUSY is
returned to network stack in order not to
drop the packets and retry transmission of the
packets when ring is emptied.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some events are ignored for purpose; such events should not
be treated as "unhandled events". Replace info message
saying "unhandled" with debug one saying "ignore", to reduce
dmesg pollution
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add the hardware name, revision and update the pci_id table.
Currently there're two HW ref. designs available I'm aware of,
with 1.0.2 and 1.1 chip revisions. I've access and been using
the first one so far and this patch cover only it.
QCA9377 inherits most of the stuff (e.g. fw interfaces)
from QCA61x4 design, so the integration was pretty straightforward.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To reflect configured antenna settings in HT/VHT MCS map,
reload the HT/VHT capabilities upon antenna change.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Move HT and VHT capabiltity setup static functions to avoid
forward declaration.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HT/VHT MCS rateset should be filled only for configured chainmask
rather that max supported chainmask. Fix that by checking configured
chainmask while filling HT/VHT MCS rate map.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Removing supported chainmask fields as it can be always derived
from num_rf_chains.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For the messages from host to target, shadow copy of CE descriptors
are maintained in source ring. Before writing actual CE descriptor,
first shadow copy is filled and then it is copied to CE address space.
To optimize in download path and to reduce d-cache pressure, removing
shadow copy of CE descriptors. This will also reduce driver memory
consumption by 33KB during on device probing.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The physical address necessary to unmap DMA ('bufferp') is stored
in ath10k_skb_cb as 'paddr'. ath10k doesn't rely on the meta/transfer_id
when handling send completion (htc ep id is stored in sk_buff control
buffer). So the unused output arguments {bufferp, nbytesp and transfer_idp}
are removed from CE send completion. This change is needed before removing
the shadow copy of copy engine (CE) descriptors in follow up patch.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
CE diag window access is serialized (it has to be by design) so
there's no way to get a different send completion. so there's no
need for post completion validation.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently to avoid uncached memory access while filling up copy engine
descriptors, shadow descriptors are used. This can be optimized further
by removing shadow descriptors. To achieve that first shadow ring
dependency in ce_send is removed by creating local copy of the
descriptor on stack and make a one-shot copy into the "uncached"
descriptor.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch adds support for getting firmware debug stats in 10.4 fw.
Signed-off-by: Manikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add WMI-TLV and FW API support in ath10k testmode.
Ath10k can get right wmi command format from UTF image
to communicate UTF firmware.
Signed-off-by: Alan Liu <alanliu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
European Union has made it mandatory that all devices working in 2.4 GHz
has to adhere to the ETSI specification (ETSI EN 300 328 V1.9.1)
beginnig this year. The standard basically speaks about interferences
in 2.4Ghz band.
For example, when 802.11 device detects interference, TX must be stopped
as long as interference is present.
Adaptive CCA is a feature, when enabled the device learns from the
environment and configures CCA levels adaptively. This will improve
detecting interferences and the device can stop trasmissions till the
interference is present eventually leading to good performances in
varying interference conditions.
The patch includes code for enabling adaptive CCA for 10.2.4 firmware on
QCA988X.
Signed-off-by: Maharaja <c_mkenna@qti.qualcomm.com>
Signed-off-by: Manikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ssb bus can be found on various "host" devices like PCI/PCMCIA/SDIO.
Every ssb bus contains cores AKA devices.
The main idea is to have ssb driver scan/initialize bus and register
ready-to-use cores. This way ssb drivers can operate on a single core
mostly ignoring underlaying details.
For some reason PCMCIA support was split between ssb and b43. We got
PCMCIA host device probing in b43, then bus scanning in ssb and then
wireless core probing back in b43. The truth is it's very unlikely we
will ever see PCMCIA ssb device with no 802.11 core but I still don't
see any advantage of the current architecture.
With proposed change we get the same functionality with a simpler
architecture, less Kconfig symbols, one killed EXPORT and hopefully
cleaner b43. Since b43 supports both: ssb & bcma I prefer to keep ssb
specific code in ssb driver.
This mostly moves code from b43's pcmcia.c to bridge_pcmcia_80211.c. We
already use similar solution with b43_pci_bridge.c. I didn't use "b43"
in name of this new file as in theory any driver can operate on wireless
core.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In uap mode the carrier is not enabled until after the first STA joins.
The carrier triggers the bridge to start its state machine, and if STP
is enabled, it takes 4 seconds as it transitions from disabled to
forwarding. During this time the bridge drops all traffic, and the EAPOL
handshake times out after 3 seconds, preventing stations from joining.
Follow the logic used in mac80211 and start the carrier in start_ap
and disable it in stop_ap. This has a nice benefit of allowing the
first station connection time to be reduced by up to 75% when STP is
in use.
Signed-off-by: Martin Faltesek <mfaltesek@google.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wcn36xx implements a ring buffer for transmitted frames for each
(high and low priority) DMA channel. The ring buffers are lockless:
new frames are inserted at the head of the queue, while finished
packets are reaped from the tail.
Unfortunately, the list manipulations are missing any kind of barriers
so are susceptible to various races: for example, a TX completion
handler might read an updated desc->ctrl before the head has actually
advanced, and then null out the ctl->skb pointer while it is still
being used in the TX path.
Simplify things here by adding a spin lock when traversing the ring.
This change increased stability for me without adding any noticeable
overhead on my platform (xperia z).
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some of the ath9k_phyerr enums were wrong from the
beginning (and even before). Most of the time the
codes were used for counters to be displayed over
debugfs, which made this a non-functional issue.
Some (e.g. ATH9K_PHYERR_FALSE_RADAR_EXT) are used
for radar detection and require the correct code
to work as intended.
This patch includes:
a) fixes
ATH9K_PHYERR_FALSE_RADAR_EXT: 24 => 36
ATH9K_PHYERR_CCK_LENGTH_ILLEGAL: 32 => 28
ATH9K_PHYERR_CCK_POWER_DROP: 33 => 29
ATH9K_PHYERR_HT_CRC_ERROR: 34 => 32
ATH9K_PHYERR_HT_LENGTH_ILLEGAL: 35 => 33
ATH9K_PHYERR_HT_RATE_ILLEGAL: 36 => 34
b) extensions
ATH9K_PHYERR_CCK_BLOCKER = 24
ATH9K_PHYERR_HT_ZLF = 35
ATH9K_PHYERR_GREEN_FIELD = 37
Aside from the correction and completion made in
the enum, the patch also extends the display of
the related counters in the debugfs.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The current code exits after alloc_orinocodev, but fails to change the
return value to something that indicates the failure. This patch
changes the return value to -ENOMEM.
https://bugzilla.kernel.org/show_bug.cgi?id=106181
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
SIOCSIWAP (airo_set_wap) affects scan: only the AP specified by
SIOCSIWAP is present in scan results.
This makes NetworkManager work for the first time but then unable to
find any other APs.
Clear APList before starting scan and set it back after scan completes
to work-around the problem.
To avoid losing packets during scan, modify disable_MAC() to omit
netif_carrier_off() call when lock == 2.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of dynamically allocating APList, make it a member of struct
airo_info to always track state of APList_rid.
This simplifies suspend/resume and allows removal of readAPListRid.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* fixes and cleanups in scan
* support of several scan plans
* improvements in FTM
* fixes in FW API
* improvements in the failure paths when the bus is dead
* other various small things here and there
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJWLMIEAAoJEC0Llv5uNjIBWjYQAJrk79EyhKLJoTVNAkLVggun
zk/yEZM/pCkxiunHwOhcxKDcQhRVIlMARQCzG8V7jUa3nWOrUFn7Moh5FB9NS80L
aS92HvUAGcPqXFM2sqanPr3xrGz+tsJ1OWW0u2GljmOwUP2V69UhhZuw+TWE94Hv
l27x3odL/4USaMv7ZZB55POosVlg3G79Xn47eyCTJVewlSizmXCKG6NDdtRLS6JZ
GEB8bFCr/kS/j0Xa+NtB8Ylc1vKKNbIDGjwnzX98vUUDsFHU7J4frcnPtzBkGlJ0
deNRV6HscvYU9aECibBqVSZ/tenSIKPOBPOMGhT3VOK+401VVOTR3FOjzLsdvZVX
6oJ5R+U/Ue7OWAtqd5wf7kDbBUTCMdAczAJFHQjXigD1OBCEdWIcdyIhDeJBxcbi
aKVPt+tHQQBxUMG938v68Lj40fO5vVreRAwKScpr7mOLW22Vlio9GwvPAnaVu55a
IMIWOEde3l5uZ/k+9L0qi5XQMUz5w5deHCVBFW1A2WE3uWqhK0OKPR7Hx4hd6nT/
EesevSPFJllGpB862Gs8GgE+RwxKhN9QIjlBubi2Lz9/cq5WneN8dTfjdkpxfmyi
0C90lXVjd5HrBPtaU8BqZWXcYYfAxVqC3yeW4aaeKjeVXOQrbTqlhbVVDpTA0B/s
+8oyFzwoFg1v0M2pUUSF
=a6Vu
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2015-10-25' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* bug fix for TDLS
* fixes and cleanups in scan
* support of several scan plans
* improvements in FTM
* fixes in FW API
* improvements in the failure paths when the bus is dead
* other various small things here and there
delete action of ETHTOOL_ID_ON/ETHTOOL_ID_OFF in XGE ethtool -p,
so Hardware control the LED state instead of software.
Signed-off-by: Li Peng <lipeng321@huawei.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: yankejian <yankejian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increased TX_TIMEOUT to 5HZ to accommodate worst case situation
for traffic and CPU intensive use cases
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Abhimanyu <abhimanyu@freescale.com>
Acked-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* using netdev carrier state
* add and rework some cfg80211 callbacks mainly for AP mode
* use devcoredump when triggered by firmware event
realtek
* create new directory drivers/net/wireless/realtek/ for all realtek
drivers, not visible to users (no kconfig changes etc)
* add rtl8xxxu, a new mac80211 driver for RTL8723AU, RTL8188CU,
RTL8188RU, RTL8191CU, RTL8192CU and hopefully more in the future
ath10k
* add board 2 API support for automatically choosing correct board file
* data path optimisations
* disable PCI power save for qca988x and QCA99x0 due to interop reasons
wil6210
* BlockAckReq support
* firmware crashdump using devcoredump
* capture all frames with sniffer
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJWLzQ5AAoJEG4XJFUm622btRwH/A6fS7p5uSZzH5lIU8ZBLc7X
MzC1jYVepHXaR5+OhBIbQ5oSo47Y4xqMeO2ylFMpUSg4vntqR9yZNVH2lXV5EfPB
fIaGYIsb3ExjAFoIjFUBwqSOB7CCZK5myk+SLiOu9XghjsLObP5JLKgA49PGhFRn
CCuDq9diDNeJBnVzTS1ms5wO6RmOBiizzjbu7adJI0Hu63z2+P4pNMG4Zz6E1z97
z8DRFEwdNN9gKHIaEC61h7ZT9XDB/Tj31Wl3Irbi4GBS7sRXnFK46FYU8fMVDbDZ
ykj05sq6nTrfwfVZtXbV3SxlYNSN4SFFRuskon6IUcIzlNTuIULgvlpCjJJ6tyQ=
=pFoQ
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2015-10-27' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
here's a bigger pull request for 4.4. The diffstat looks scary as we
created a new directory realtek for all realtek drivers. In the future
I'm planning to create similar directories for all vendors, currently we
just have ath, mediatek and realtek. This change has been in linux-next
for a couple of weeks so it should be safe, but of course you never
know.
There's also a new driver rtl8xxxu for few realtek USB devices. This
just made it to the last linux-next build.
Otherwise there's nothing really special, more info below. If time
permits, and it's ok for you, I'm hoping to send you a one more pull
request this week.
brcmfmac
* using netdev carrier state
* add and rework some cfg80211 callbacks mainly for AP mode
* use devcoredump when triggered by firmware event
realtek
* create new directory drivers/net/wireless/realtek/ for all realtek
drivers, not visible to users (no kconfig changes etc)
* add rtl8xxxu, a new mac80211 driver for RTL8723AU, RTL8188CU,
RTL8188RU, RTL8191CU, RTL8192CU and hopefully more in the future
ath10k
* add board 2 API support for automatically choosing correct board file
* data path optimisations
* disable PCI power save for qca988x and QCA99x0 due to interop reasons
wil6210
* BlockAckReq support
* firmware crashdump using devcoredump
* capture all frames with sniffer
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reduces the overhead of locking for busy poll.
Previously the state was protected by a lock, whereas now
it's manipulated solely with atomic operations.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds basic ethtool operations to the qed driver, allowing support in:
- Statistics gathering [ethtool -S]
- Setting of debug level [ethtool -s <interface> msglvl]
- Getting basic information [ethtool, ethtool -i]
In addition it adds the ability to change the MTU.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device statistics can be gathered on-demand. This adds the qed support for
reading the statistics [both function and port] from the device, and adds
to the public API a method for requesting the current statistics.
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds basic link functionality to qede - driver still doesn't provide
users with an API to change any link property, but it does request qed to
initialize the link using default configuration, and registers a callback
that allows it to get link notifications.
This patch adds the ability of the driver to set the carrier as active and
to enable traffic as a result of async. link notifications.
Following this patch, driver should be capable of running traffic.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Physical link is handled by the management Firmware.
This patch lays the infrastructure for attention handling in the driver,
as link change notifications arrive via async. attentions,
as well the handling of such notifications.
This patch also extends the API with the protocol drivers by adding
registered callbacks which the protocol driver passes to qed in order
to be notified of async. events originating from the FW/HW.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ability to configure basic classification in driver by
implementing ndo_set_mac_address() and ndo_set_rx_mode().
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch includes the basic Rx/Tx support for the driver [although
carrier will still never be turned on].
Following this patch the driver registers a network device, initializes
it and prepares it for traffic.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds to the qed the support to configure various L2 elements,
such as channels and basic filtering conditions.
It also enhances its public API to allow qede to later utilize this
functionality.
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Qlogic Everest Driver for Ethernet is the Ethernet specific module for
QL4xxx ethernet products by Qlogic.
This patch adds a very minimal PCI driver, one that doesn't yet register
a network device, but one that does interact with qed and does a basic
initialization of the HW.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a public API for a network driver to work on top of QED.
The interface itself is very minimal - it's mostly infrastructure, as the
only content it has after this patch is a query for HW-based information
required for the creation of a network interface [I.e., no actual
protocol-specific configurations are supported].
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Qlogic Everest Driver is the backend module for the QL4xxx ethernet
products by Qlogic.
This module serves two main purposes:
1. It's responsible to contain all the common code that will be shared
between the various drivers that would be used with said line of
products. Flows such as chip initialization and de-initialization
fall under this category.
2. It would abstract the protocol-specific HW & FW components, allowing
the protocol drivers to have a clean APIs which is detached in its
slowpath configuration from the actual HSI.
This adds a very basic module without any protocol-specific bits.
I.e., this adds a basic implementation that almost entirely falls under
the first category.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xceiver handling (enable/disable) of the com20020 cards. The driver now handles
link status change detection. The EAE PCI-ARCNET cards now make use of the
rotary encoded subdevice indexing and got support for led triggers on transmit
and reconnection events.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=NNwD
-----END PGP SIGNATURE-----
Merge tag 'arcnet-for-4.4-rc1' of git://git.pengutronix.de/git/mgr/linux
Michael Grzeschik says:
====================
This series includes code simplifaction. The main changes are the correct
xceiver handling (enable/disable) of the com20020 cards. The driver now handles
link status change detection. The EAE PCI-ARCNET cards now make use of the
rotary encoded subdevice indexing and got support for led triggers on transmit
and reconnection events.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
While the current driver mostly supports BCM7445 which has a hardcoded
location for its MoCA port on port 7 and port 0 for its internal PHY,
this is not necessarily true for all other chips out there such as
BCM3390 for instance.
Walk the list of ports from Device Tree, get their port number ("reg"
property), and then parse the "phy-mode" property and initialize two
internal variables: moca_port and a bitmask of internal PHYs. Since we
use interrupts for the MoCA port, we introduce two helper functions to
enable/disable interrupts and do this at the appropriate bank (INTRL2_0
or INTRL2_1).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the FDB add, delete, and dump operations. The add and
delete operations are implemented using directed ARL operations using
the specified MAC address and consist in a read operation, write and
readback operation.
The dump operation consists in using the ARL search and software
filtering entries which are not for the desired port.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kbuild reported:
rtl8xxxu.c:5786:32: warning: ‘rtl8192cu_fops’ defined but not used [-Wunused-variable]
Fix it by adding temporary ifdefs around the static functions.
Fixes: 033695bdf6 ("rtl8xxxu: move devices supported by rtlwifi under UNTESTED config")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The arcnet device has no interrupt to detect if the link has changed
from disconnected to connected. This patch adds an timer to toggle the
link detection. The timer will get retriggered as long as the
reconnection interrupts accure. If the recon interrupts hold off
for >1s we define the connection stable again.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
The EAE PLX-PCI card has special leds on the the main io pci resource
bar. This patch adds support to trigger the conflict and data leds with
the packages.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
The EAE PLX-PCI card has a special rotary encoder
to configure the address of every card individually.
We take this information for the initial setup of
the cards dev_id.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
This patch sets the dev_port according to the index of
the card. This can be used by udev to name the ports
in userspace.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
This patch changes the driver to properly work with the linux netif
interface. The controller gets enabled on open and disabled on close.
Therefor it removes every bogus start of the xceiver. It only gets
enabled on com20020_open and disabled on com20020_close.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
The call for dev_free_skb is done only once. This patch
moves its call to its only user and removes the obsolete
condition variable.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
bnxt_gro_skb() has unused variables when CONFIG_INET is not set. We
really cannot support hardware GRO if CONFIG_INET is not set, so
compile out bnxt_gro_skb() completely and define BNXT_FLAG_GRO to be 0
if CONFIG_INET is not set. This will effectively always disable
hardware GRO if CONFIG_INET is not set.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the mask used to update the LED configuration so that it clears
the necessary bits as well as setting the bits according to the mask.
Also reverse the LED configuration to show the Link state + collisions in
LEDA and the Link state + TX/RX events in LEDB.
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
