The DECON headers contain only defines for registers. There are no
other drivers using them so this should be put locally to the Exynos DRM
driver. Keeping headers local helps managing the code.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
I ran into a build error on x86:
drivers/gpu/drm/exynos/exynos5433_drm_decon.c: In function 'decon_conf_irq':
drivers/gpu/drm/exynos/exynos5433_drm_decon.c:706:2: error: implicit declaration of function 'irq_set_status_flags'; did you mean 'dquot_state_flag'? [-Werror=implicit-function-declaration]
irq_set_status_flags(irq, IRQ_NOAUTOEN);
Adding the missing include fixes the error.
Fixes: b37d53a038 ("drm/exynos/decon5433: move TE handling to DECON")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
A recent commit (272725c7db) has removed
the use of 'bits_per_pixel' in DRM. However the corresponding Exynos
driver code still uses the ambiguous 'bpp', even though it is now
initialized from fb->cpp[0].
Consistenly use 'cpp' in FIMD, DECON7 and DECON5433 drivers.
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Since panel's mode of work is propagated properly from panel to DECON,
there is no need to use redundant private device tree property.
The only issue with such approach is that check for required interrupts
should be postponed until panel communicate its requirements, ie to
mode validation phase - mode_valid callback.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
To allow runtime validation of mode of work irq request
code should be split into two separate phases:
- irq reqesting,
- irq checking.
Following patches will move 2nd phase to mode validation phase.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Linux core provide helpers for polling with timeout, lets use them.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
TE IRQ is enabled only in case of sw-trigger, so trigger check
is redundant.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Exynos tracked suspend state to prevent touching disabled HW. After
fixing disable order in HDMI and moving TE handling to DECON it is
not needed anymore - all IRQ handlers and callbacks touching HW
are called only with enabled DECON.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The flag was used to trigger software update in TE IRQ handler only
if framebuffers were replaced. Since TE update is triggered always
when VBLANKs are enabled and after framebuffer replacement VBLANKs
are always enabled the flag becomes redundant.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The flag was used to check if IRQ handlers can touch HW. Since driver
enables IRQs only if hardware is enabled the flag becomes redundant.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Since DECON uses enable_irq/disable_irq to full control IRQs,
there is no point in having flags to trace it separately.
As a bonus condition for software trigger becomes always true,
so it can be removed.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
DECON is the only user of TE signal, moving all TE related
code to DECON driver allows to precise control of IRQ handlers.
This control allows to fix race between IRQ handler and DECON disable
code - now it is possible to disable DECON during IRQ handling
which can result in kernel crash. Beside race fixing this change
allows further code simplification.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
When vblanks are enabled userspace and/or kernel can expect vblank
interrupt at declared period of time. To generate vblank interrupt
image transfer must be triggered. This patch fixes vblank timeouts
in case of sw-trigger mode.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
There is no point in protecting only particular windows during update.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
BIT_IRQS_ENABLED flag duplicates drm_vblank_crtc::refcount, it could be
safely removed.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Since fixing CMU code (drm/exynos/decon5433: fix CMU programming)
DECON started behave predictable and does not need special care
during DECON_UPDATE writes.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Since possible_crtcs are set by Exynos core helper pipe fields have no
raison d'etre. The only place it was used, as a hack, is
fimd_clear_channels, to avoid calling drm_crtc_handle_vblank, but DRM core
has already other protection mechanism (vblank->enabled), so it could be
safely removed.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
All Exynos planes are assigned to exactly one CRTC, it allows to simplify
initialization by moving setting of possible_crtcs to exynos_plane_init.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Since crtc index is stored in drm_crtc pipe field became redundant.
The patch beside removing the field simplifies also
exynos_drm_crtc_get_pipe_from_type.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
DECON in Exynos5433 has frame counter, it can be used to implement
get_vblank_counter callback.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The patch fixes copy/paste bug introduced during code refactoring.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: b93c2e8b5d ("drm/exynos/decon5433: configure sysreg in case of hardware trigger")Fixes:
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
DECON in case of video mode generates interrupt by default at start
of vertical back porch. As this interrupt is used to generate VBLANK
events more optimal point is start of vertical front porch.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Current implementation of event handling assumes that vblank interrupt is
always called at the right time. It is not true, it can be delayed due to
various reasons. As a result different races can happen. The patch fixes
the issue by using hardware frame counter present in DECON to serialize
vblank and commit completion events.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
CRTC event is currently send with next vblank, or instantly in case crtc
is being disabled. This approach usually works, but in corner cases it can
result in premature event generation. Only device driver is able to verify
if the event can be sent. This patch is a first step in that direction - it
moves event handling to the drivers.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
"&" was obviously intended instead of "|". The original condition is
always true.
Fixes: b93c2e8b5d ("drm/exynos/decon5433: configure sysreg in case of hardware trigger")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
In case of interlace mode irq is generated for odd and even fields, but
vblank should be signaled only for the last emitted field.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Some registers should be programmed differently in interlace mode.
Additionally IP does not signal stop state properly in interlaced
mode, so warning has been removed.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
In case of HW trigger mode, sysreg register should be configured to
enable TE functionality. The patch refactors also trigger setup function.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
- cleanups&fixes for dw-hdmi bride driver (Laurent)
- updates for adv bridge driver (John Stultz) for nexus
- drm_crtc_from_index helper rollout (Shawn Guo)
- removing drm_framebuffer_unregister_private from drivers&core
- target_vblank (Andrey Grodzovsky)
- misc tiny stuff
* tag 'drm-misc-next-2017-01-23' of git://anongit.freedesktop.org/git/drm-misc: (49 commits)
drm: qxl: Open code teardown function for qxl
drm: qxl: Open code probing sequence for qxl
drm/bridge: adv7511: Re-write the i2c address before EDID probing
drm/bridge: adv7511: Reuse __adv7511_power_on/off() when probing EDID
drm/bridge: adv7511: Rework adv7511_power_on/off() so they can be reused internally
drm/bridge: adv7511: Enable HPD interrupts to support hotplug and improve monitor detection
drm/bridge: adv7511: Switch to using drm_kms_helper_hotplug_event()
drm/bridge: adv7511: Use work_struct to defer hotplug handing to out of irq context
drm: vc4: use crtc helper drm_crtc_from_index()
drm: tegra: use crtc helper drm_crtc_from_index()
drm: nouveau: use crtc helper drm_crtc_from_index()
drm: mediatek: use crtc helper drm_crtc_from_index()
drm: kirin: use crtc helper drm_crtc_from_index()
drm: exynos: use crtc helper drm_crtc_from_index()
dt-bindings: display: dw-hdmi: Clean up DT bindings documentation
drm: bridge: dw-hdmi: Assert SVSRET before resetting the PHY
drm: bridge: dw-hdmi: Fix the name of the PHY reset macros
drm: bridge: dw-hdmi: Define and use macros for PHY register addresses
drm: bridge: dw-hdmi: Detect PHY type at runtime
drm: bridge: dw-hdmi: Handle overflow workaround based on device version
...
Backmerge Linus master to get the connector locking revert.
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux: (645 commits)
sysctl: fix proc_doulongvec_ms_jiffies_minmax()
Revert "drm/probe-helpers: Drop locking from poll_enable"
MAINTAINERS: add Dan Streetman to zbud maintainers
MAINTAINERS: add Dan Streetman to zswap maintainers
mm: do not export ioremap_page_range symbol for external module
mn10300: fix build error of missing fpu_save()
romfs: use different way to generate fsid for BLOCK or MTD
frv: add missing atomic64 operations
mm, page_alloc: fix premature OOM when racing with cpuset mems update
mm, page_alloc: move cpuset seqcount checking to slowpath
mm, page_alloc: fix fast-path race with cpuset update or removal
mm, page_alloc: fix check for NULL preferred_zone
kernel/panic.c: add missing \n
fbdev: color map copying bounds checking
frv: add atomic64_add_unless()
mm/mempolicy.c: do not put mempolicy before using its nodemask
radix-tree: fix private list warnings
Documentation/filesystems/proc.txt: add VmPin
mm, memcg: do not retry precharge charges
proc: add a schedule point in proc_pid_readdir()
...
DECON_TV requires STANDALONE_UPDATE after output enabling, otherwise it does
not start. This change is neutral for DECON.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
DECON_CMU register has reserved bits which should not be zeroed, otherwise
IP can behave strangely and cause IOMMU faults.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
decon_commit is called just after reset so video is disabled anyway.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
STANDALONE_UPDATE_F should be set if something changed in plane configurations,
including plane disable.
The patch fixes page-faults bugs, caused by decon still using framebuffers
of disabled planes.
v2: fixed clear-bit code (Thx Marek)
v3: use test_and_clear_bit (Thx Joonyoung)
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Improper usage of DECON_UPDATE register leads to subtle errors.
If it set in decon_commit when there are no active windows it results
in slow registry updates - all subsequent shadow registry updates takes more
than full vblank. On the other side if it is not set when there are
active windows it results in garbage on the screen after suspend/resume of
FB console.
The patch hopefully fixes it.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Declare exynos_drm_crtc_ops structures as const as they are only passed
as an argument to the function exynos_drm_crtc_create. This argument is
of type const struct exynos_drm_crtc_ops *, so exynos_drm_crtc_ops
structures having this property can be declared const.
Done using Coccinelle:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct exynos_drm_crtc_ops i@p={...};
@ok@
position p;
identifier r.i;
@@
exynos_drm_crtc_create(...,&i@p,...)
@bad@
position p!={r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
+const
struct exynos_drm_crtc_ops i;
File size before:
text data bss dec hex filename
5008 280 0 5288 14a8 exynos/exynos5433_drm_decon.o
File size after:
text data bss dec hex filename
5120 176 0 5296 14b0 exynos/exynos5433_drm_decon.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1483984493-25284-1-git-send-email-bhumirks@gmail.com
Exynos DRM framework handled page-flip event with custom code.
The patch replaces it with drm-core vblank queue.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
It seems trigger cannot be configured too early, otherwise it does not work in
case of panel. The patch fixes also trigger flag logic, previously HW-TRIGGER
flag was cleared in case of panel - as a result panel used always software
trigger.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Software trigger should not be used if hardware trigger is configured.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
vblank should be signaled to userspace after reading framebuffers not before,
signaling it in TE interrupt looks wrong. TE triggers reading framebuffers
so it is the worst moment. Tearing is not observable because hardware prevents
it, but there are frequently skipped vblank events.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch removes suffixes from I80 relevant register definitions,
which are misleading.
This is based on top of below patch set,
http://www.spinics.net/lists/dri-devel/msg104057.html
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch cleans up interface type relevant codes.
Trigger mode is determinded only by i80 mode, which isn't
related to Display types - HDMI or Display controller.
So this patch makes the trigger mode to be set only in case of
i80 mode - For DECON-TV, HW Trigger mode is flaged mandatorily
because HDMI Timing Generator generates VSYNC signal
which works as a hardware trigger.
Changelog v2.
- If interface type is HDMI then set out_type to I80.
- fix compile warning.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
decon_atomic_begin and decon_atomic_flush protects all windows already.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
