Change cpts_active_slave to active_slave so that the same DT property
can be used to ethtool and SIOCGMIIPHY.
CC: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows ethernet drivers (such as the mv643xx_eth) to support
Wake on LAN on platforms where PHY registers have to be configured
for Wake on LAN (e.g. the Marvell Kirkwood based qnap TS-119P II).
Signed-off-by: Michael Stapelberg <michael@stapelberg.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the second of the TLP patch series; it augments the basic TLP
algorithm with a loss detection scheme.
This patch implements a mechanism for loss detection when a Tail
loss probe retransmission plugs a hole thereby masking packet loss
from the sender. The loss detection algorithm relies on counting
TLP dupacks as outlined in Sec. 3 of:
http://tools.ietf.org/html/draft-dukkipati-tcpm-tcp-loss-probe-01
The basic idea is: Sender keeps track of TLP "episode" upon
retransmission of a TLP packet. An episode ends when the sender receives
an ACK above the SND.NXT (tracked by tlp_high_seq) at the time of the
episode. We want to make sure that before the episode ends the sender
receives a "TLP dupack", indicating that the TLP retransmission was
unnecessary, so there was no loss/hole that needed plugging. If the
sender gets no TLP dupack before the end of the episode, then it reduces
ssthresh and the congestion window, because the TLP packet arriving at
the receiver probably plugged a hole.
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch series implement the Tail loss probe (TLP) algorithm described
in http://tools.ietf.org/html/draft-dukkipati-tcpm-tcp-loss-probe-01. The
first patch implements the basic algorithm.
TLP's goal is to reduce tail latency of short transactions. It achieves
this by converting retransmission timeouts (RTOs) occuring due
to tail losses (losses at end of transactions) into fast recovery.
TLP transmits one packet in two round-trips when a connection is in
Open state and isn't receiving any ACKs. The transmitted packet, aka
loss probe, can be either new or a retransmission. When there is tail
loss, the ACK from a loss probe triggers FACK/early-retransmit based
fast recovery, thus avoiding a costly RTO. In the absence of loss,
there is no change in the connection state.
PTO stands for probe timeout. It is a timer event indicating
that an ACK is overdue and triggers a loss probe packet. The PTO value
is set to max(2*SRTT, 10ms) and is adjusted to account for delayed
ACK timer when there is only one oustanding packet.
TLP Algorithm
On transmission of new data in Open state:
-> packets_out > 1: schedule PTO in max(2*SRTT, 10ms).
-> packets_out == 1: schedule PTO in max(2*RTT, 1.5*RTT + 200ms)
-> PTO = min(PTO, RTO)
Conditions for scheduling PTO:
-> Connection is in Open state.
-> Connection is either cwnd limited or no new data to send.
-> Number of probes per tail loss episode is limited to one.
-> Connection is SACK enabled.
When PTO fires:
new_segment_exists:
-> transmit new segment.
-> packets_out++. cwnd remains same.
no_new_packet:
-> retransmit the last segment.
Its ACK triggers FACK or early retransmit based recovery.
ACK path:
-> rearm RTO at start of ACK processing.
-> reschedule PTO if need be.
In addition, the patch includes a small variation to the Early Retransmit
(ER) algorithm, such that ER and TLP together can in principle recover any
N-degree of tail loss through fast recovery. TLP is controlled by the same
sysctl as ER, tcp_early_retrans sysctl.
tcp_early_retrans==0; disables TLP and ER.
==1; enables RFC5827 ER.
==2; delayed ER.
==3; TLP and delayed ER. [DEFAULT]
==4; TLP only.
The TLP patch series have been extensively tested on Google Web servers.
It is most effective for short Web trasactions, where it reduced RTOs by 15%
and improved HTTP response time (average by 6%, 99th percentile by 10%).
The transmitted probes account for <0.5% of the overall transmissions.
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Micrel PHY KSZ8031 is similar to KSZ8021 and also requires the special
initialization of "Operation Mode Strap Override" in reg 0x16
introduced in 212ea99 (phy/micrel: Implement support for KSZ8021).
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/intel/e1000e/netdev.c
Minor conflict in e1000e, a line that got fixed in 'net'
has been removed in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
tw_cookie_values is never used in the TCP-stack.
It was added by 435cf559f (TCPCT part 1d: define TCP cookie option,
extend existing struct's), but already at that time it was not used at
all, nor mentioned in the commit-message.
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to iptunnel_xmit(), group these operations into a
helper function.
This by the way fixes the missing u64_stats_update_begin()
and u64_stats_update_end() for 32 bit arch.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Pravin B Shelar <pshelar@nicira.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With recent patches from Pravin, most tunnels can't use iptunnel_xmit()
any more, due to ip_select_ident() and skb->ip_summed. But we can just
move these operations out of iptunnel_xmit(), so that tunnels can
use it again.
This by the way fixes a bug in vxlan (missing nf_reset()) for net-next.
Cc: Pravin B Shelar <pshelar@nicira.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull namespace bugfixes from Eric Biederman:
"This is three simple fixes against 3.9-rc1. I have tested each of
these fixes and verified they work correctly.
The userns oops in key_change_session_keyring and the BUG_ON triggered
by proc_ns_follow_link were found by Dave Jones.
I am including the enhancement for mount to only trigger requests of
filesystem modules here instead of delaying this for the 3.10 merge
window because it is both trivial and the kind of change that tends to
bit-rot if left untouched for two months."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
proc: Use nd_jump_link in proc_ns_follow_link
fs: Limit sys_mount to only request filesystem modules (Part 2).
fs: Limit sys_mount to only request filesystem modules.
userns: Stop oopsing in key_change_session_keyring
Adds generic tunneling offloading support for IPv4-UDP based
tunnels.
GSO type is added to request this offload for a skb.
netdev feature NETIF_F_UDP_TUNNEL is added for hardware offloaded
udp-tunnel support. Currently no device supports this feature,
software offload is used.
This can be used by tunneling protocols like VXLAN.
CC: Jesse Gross <jesse@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds inner mac header. This will be used in next patch
to find tunner header length. Header len is required to copy tunnel
header to each gso segment.
This patch does not change any functionality.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Earlier SG was unset if CSUM was not available for given device to
force skb copy to avoid sending inconsistent csum.
Commit c9af6db4c1 (net: Fix possible wrong checksum generation)
added explicit flag to force copy to fix this issue. Therefore
there is no need to link SG and CSUM, following patch kills this
link between there two features.
This patch is also required following patch in series.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This same driver can be used by atmel based touchscreens and touchpads
(buttonpads). Platform data may specify a device is a touchpad
using the is_tp flag.
This will cause the driver to perform some touchpad specific
initializations, such as:
* register input device name "Atmel maXTouch Touchpad" instead of
Touchscreen.
* register BTN_LEFT & BTN_TOOL_* event types.
* register axis resolution (as a fixed constant, for now)
* register BUTTONPAD property
* process GPIO buttons using reportid T19
Input event GPIO mapping is done by the platform data key_map array.
key_map[x] should contain the KEY or BTN code to send when processing
GPIOx from T19. To specify a GPIO as not an input source, populate
with KEY_RESERVED, or 0.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Tested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__ipv6_addr_needs_scope_id checks if an ipv6 address needs to supply
a 'sin6_scope_id != 0'. 'sin6_scope_id != 0' was enforced in case
of link-local addresses. To support interface-local multicast these
checks had to be enhanced and are now consolidated into these new helper
functions.
v2:
a) migrated to struct ipv6_addr_props
v3:
a) reverted changes for ipv6_addr_props
b) test for address type instead of comparing scope
v4:
a) unchanged
Suggested-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split the vSockets header into kernel and UAPI parts. The former gets the bits
that used to be in __KERNEL__ guards, while the latter gets everything that is
user-visible. Tested by compiling vsock (+transport) and a simple user-mode
vSockets application.
Reported-by: David Howells <dhowells@redhat.com>
Acked-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Andy King <acking@vmware.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull drm fixes from Dave Airlie:
"Misc radeon, nouveau, mgag200 and intel fixes.
The intel fixes should contain the fix for the touchpad on the
Chromebook - hey I'm an input maintainer now!"
Hate to pee on your parade, Dave, but I don't think being an input
maintainer is necessarily something to strive for..
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (25 commits)
drm/tegra: drop "select DRM_HDMI"
drm: Documentation typo fixes
drm/mgag200: Bug fix: Renesas board now selects native resolution.
drm/mgag200: Reject modes that are too big for VRAM
drm/mgag200: 'fbdev_list' in 'struct mga_fbdev' is not used
drm/radeon: don't check mipmap alignment if MIP_ADDRESS is FMASK
drm/radeon: skip MC reset as it's probably not hung
drm/radeon: add primary dac adj quirk for R200 board
drm/radeon: don't set hpd, afmt interrupts when interrupts are disabled
drm/i915: Turn off hsync and vsync on ADPA when disabling crt
drm/i915: Fix incorrect definition of ADPA HSYNC and VSYNC bits
drm/i915: also disable south interrupts when handling them
drm/i915: enable irqs earlier when resuming
drm/i915: Increase the RC6p threshold.
DRM/i915: On G45 enable cursor plane briefly after enabling the display plane.
drm/nv50-: prevent some races between modesetting and page flipping
drm/nouveau/i2c: drop parent refcount when creating ports
drm/nv84: fix regression in page flipping
drm/nouveau: Fix typo in init_idx_addr_latched().
drm/nouveau: Disable AGP on PowerPC again.
...
- Two fixes for the new intel_pstate driver from Dirk Brandewie.
- Fix for incorrect usage of the .find_bridge() callback from struct
acpi_bus_type in the USB core and subsequent removal of that
callback from Rafael J. Wysocki.
- ACPI processor driver cleanups from Chen Gang and Syam Sidhardhan.
- ACPI initialization and error messages fix from Joe Perches.
- Operating Performance Points documentation improvement from
Nishanth Menon.
- Fixes for memory leaks and potential concurrency issues and sysfs
attributes leaks during device removal in the core device PM QoS
code from Rafael J. Wysocki.
- Calxeda Highbank cpufreq driver simplification from Emilio López.
- cpufreq comment cleanup from Namhyung Kim.
- Fix for a section mismatch in Calxeda Highbank interprocessor
communication code from Mark Langsdorf (this is not a PM fix
strictly speaking, but the code in question went in through the
PM tree).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=9vaj
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael J Wysocki:
- Two fixes for the new intel_pstate driver from Dirk Brandewie.
- Fix for incorrect usage of the .find_bridge() callback from struct
acpi_bus_type in the USB core and subsequent removal of that callback
from Rafael J Wysocki.
- ACPI processor driver cleanups from Chen Gang and Syam Sidhardhan.
- ACPI initialization and error messages fix from Joe Perches.
- Operating Performance Points documentation improvement from Nishanth
Menon.
- Fixes for memory leaks and potential concurrency issues and sysfs
attributes leaks during device removal in the core device PM QoS code
from Rafael J Wysocki.
- Calxeda Highbank cpufreq driver simplification from Emilio López.
- cpufreq comment cleanup from Namhyung Kim.
- Fix for a section mismatch in Calxeda Highbank interprocessor
communication code from Mark Langsdorf (this is not a PM fix strictly
speaking, but the code in question went in through the PM tree).
* tag 'pm+acpi-3.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq / intel_pstate: Do not load on VM that does not report max P state.
cpufreq / intel_pstate: Fix intel_pstate_init() error path
ACPI / glue: Drop .find_bridge() callback from struct acpi_bus_type
ACPI / glue: Add .match() callback to struct acpi_bus_type
ACPI / porocessor: Beautify code, pr->id is u32 which is never < 0
ACPI / processor: Remove redundant NULL check before kfree
ACPI / Sleep: Avoid interleaved message on errors
PM / QoS: Remove device PM QoS sysfs attributes at the right place
PM / QoS: Fix concurrency issues and memory leaks in device PM QoS
cpufreq: highbank: do not initialize array with a loop
PM / OPP: improve introductory documentation
cpufreq: Fix a typo in comment
mailbox, pl320-ipc: remove __init from probe function
Commit 18367681a1 (ipv6 flowlabel: Convert np->ipv6_fl_list to RCU.)
omitted proper __rcu annotations.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few small things here and there, nothing major here really. The
conversion of twl4030ldo_ops to get_voltage_sel is a fix, as covered in
the commit log it fixes inconsistency in handling of the IS_UNSUP()
feature in the driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=wEGn
-----END PGP SIGNATURE-----
Merge tag 'regulator-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A few small things here and there, nothing major here really. The
conversion of twl4030ldo_ops to get_voltage_sel is a fix, as covered
in the commit log it fixes inconsistency in handling of the IS_UNSUP()
feature in the driver."
* tag 'regulator-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: fixed regulator_bulk_enable unwinding code
regulator: twl: Convert twl4030ldo_ops to get_voltage_sel
regulator: palmas: fix number of SMPS voltages
regulator: core: fix documentation error in regulator_allow_bypass
regulator: core: update kernel documentation for regulator_desc
regulator: db8500-prcmu - remove incorrect __exit markup
The code cleanups fix up W=1 compiler warnings and some unnecessary checks. The
new Kconfig option, defaulting to N, allows the rarely used eCryptfs kernel to
userspace communication channel to be compiled out. This may be the first step
in it being eventually removed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=XwgS
-----END PGP SIGNATURE-----
Merge tag 'ecryptfs-3.9-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs
Pull ecryptfs fixes from Tyler Hicks:
"Minor code cleanups and new Kconfig option to disable /dev/ecryptfs
The code cleanups fix up W=1 compiler warnings and some unnecessary
checks. The new Kconfig option, defaulting to N, allows the rarely
used eCryptfs kernel to userspace communication channel to be compiled
out. This may be the first step in it being eventually removed."
Hmm. I'm not sure whether these should be called "fixes", and it
probably should have gone in the merge window. But I'll let it slide.
* tag 'ecryptfs-3.9-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
eCryptfs: allow userspace messaging to be disabled
eCryptfs: Fix redundant error check on ecryptfs_find_daemon_by_euid()
ecryptfs: ecryptfs_msg_ctx_alloc_to_free(): remove kfree() redundant null check
eCryptfs: decrypt_pki_encrypted_session_key(): remove kfree() redundant null check
eCryptfs: remove unneeded checks in virt_to_scatterlist()
eCryptfs: Fix -Wmissing-prototypes warnings
eCryptfs: Fix -Wunused-but-set-variable warnings
eCryptfs: initialize payload_len in keystore.c
If the driver does not support the ndo_op use the generic
handler for it. This should work in the majority of cases.
Eventually the fdb_dflt_add call gets translated into a
__dev_set_rx_mode() call which should handle hardware
support for filtering via the IFF_UNICAST_FLT flag.
Namely IFF_UNICAST_FLT indicates if the hardware can do
unicast address filtering. If no support is available
the device is put into promisc mode.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HTB uses an internal pfifo queue, which limit is not reported
to userland tools (tc), and value inherited from device tx_queue_len
at setup time.
Introduce TCA_HTB_DIRECT_QLEN attribute to allow finer control.
Remove two obsolete pr_err() calls as well.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As suggested by Eric Dumazet, allow user to select mode which chooses
TX port randomly. Functionality should be more of less similar to
round-robin mode with even lower overhead.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers use a too big NAPI poll weight.
This patch adds a NAPI_POLL_WEIGHT default value
and issues an error message if a driver attempts
to use a bigger weight.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"A moderately sized pile of fixes, some specifically for merge window
introduced regressions although others are for longer standing items
and have been queued up for -stable.
I'm kind of tired of all the RDS protocol bugs over the years, to be
honest, it's way out of proportion to the number of people who
actually use it.
1) Fix missing range initialization in netfilter IPSET, from Jozsef
Kadlecsik.
2) ieee80211_local->tim_lock needs to use BH disabling, from Johannes
Berg.
3) Fix DMA syncing in SFC driver, from Ben Hutchings.
4) Fix regression in BOND device MAC address setting, from Jiri
Pirko.
5) Missing usb_free_urb in ISDN Hisax driver, from Marina Makienko.
6) Fix UDP checksumming in bnx2x driver for 57710 and 57711 chips,
fix from Dmitry Kravkov.
7) Missing cfgspace_lock initialization in BCMA driver.
8) Validate parameter size for SCTP assoc stats getsockopt(), from
Guenter Roeck.
9) Fix SCTP association hangs, from Lee A Roberts.
10) Fix jumbo frame handling in r8169, from Francois Romieu.
11) Fix phy_device memory leak, from Petr Malat.
12) Omit trailing FCS from frames received in BGMAC driver, from Hauke
Mehrtens.
13) Missing socket refcount release in L2TP, from Guillaume Nault.
14) sctp_endpoint_init should respect passed in gfp_t, rather than use
GFP_KERNEL unconditionally. From Dan Carpenter.
15) Add AISX AX88179 USB driver, from Freddy Xin.
16) Remove MAINTAINERS entries for drivers deleted during the merge
window, from Cesar Eduardo Barros.
17) RDS protocol can try to allocate huge amounts of memory, check
that the user's request length makes sense, from Cong Wang.
18) SCTP should use the provided KMALLOC_MAX_SIZE instead of it's own,
bogus, definition. From Cong Wang.
19) Fix deadlocks in FEC driver by moving TX reclaim into NAPI poll,
from Frank Li. Also, fix a build error introduced in the merge
window.
20) Fix bogus purging of default routes in ipv6, from Lorenzo Colitti.
21) Don't double count RTT measurements when we leave the TCP receive
fast path, from Neal Cardwell."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (61 commits)
tcp: fix double-counted receiver RTT when leaving receiver fast path
CAIF: fix sparse warning for caif_usb
rds: simplify a warning message
net: fec: fix build error in no MXC platform
net: ipv6: Don't purge default router if accept_ra=2
net: fec: put tx to napi poll function to fix dead lock
sctp: use KMALLOC_MAX_SIZE instead of its own MAX_KMALLOC_SIZE
rds: limit the size allocated by rds_message_alloc()
MAINTAINERS: remove eexpress
MAINTAINERS: remove drivers/net/wan/cycx*
MAINTAINERS: remove 3c505
caif_dev: fix sparse warnings for caif_flow_cb
ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver
sctp: use the passed in gfp flags instead GFP_KERNEL
ipv[4|6]: correct dropwatch false positive in local_deliver_finish
l2tp: Restore socket refcount when sendmsg succeeds
net/phy: micrel: Disable asymmetric pause for KSZ9021
bgmac: omit the fcs
phy: Fix phy_device_free memory leak
bnx2x: Fix KR2 work-around condition
...
Pull irq fixes and cleanups from Thomas Gleixner:
"Commit e5ab012c32 ("nohz: Make tick_nohz_irq_exit() irq safe") is
the first commit in the series and the minimal necessary bugfix, which
needs to go back into stable.
The remanining commits enforce irq disabling in irq_exit(), sanitize
the hardirq/softirq preempt count transition and remove a bunch of no
longer necessary conditionals."
I personally love getting rid of the very subtle and confusing
IRQ_EXIT_OFFSET thing. Even apart from the whole "more lines removed
than added" thing.
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irq: Don't re-enable interrupts at the end of irq_exit
irq: Remove IRQ_EXIT_OFFSET workaround
Revert "nohz: Make tick_nohz_irq_exit() irq safe"
irq: Sanitize invoke_softirq
irq: Ensure irq_exit() code runs with interrupts disabled
nohz: Make tick_nohz_irq_exit() irq safe
Pull smpboot bugfix from Thomas Gleixner:
"A single bugfix for a regression introduced with the conversion of the
stop machine threads to the generic smpboot thread management
facility"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
stop_machine: Mark per cpu stopper enabled early
After PCI and USB have stopped using the .find_bridge() callback in
struct acpi_bus_type, the only remaining user of it is SATA, but SATA
only pretends to be a user, because it points that callback to a stub
always returning -ENODEV.
For this reason, drop the SATA's dummy .find_bridge() callback and
remove .find_bridge(), which is not used any more, from struct
acpi_bus_type entirely.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
USB uses the .find_bridge() callback from struct acpi_bus_type
incorrectly, because as a result of the way it is used by USB every
device in the system that doesn't have a bus type or parent is
passed to usb_acpi_find_device() for inspection.
What USB actually needs, though, is to call usb_acpi_find_device()
for USB ports that don't have a bus type defined, but have
usb_port_device_type as their device type, as well as for USB
devices.
To fix that replace the struct bus_type pointer in struct
acpi_bus_type used for matching devices to specific subsystems
with a .match() callback to be used for this purpose and update
the users of struct acpi_bus_type, including USB, accordingly.
Define the .match() callback routine for USB, usb_acpi_bus_match(),
in such a way that it will cover both USB devices and USB ports
and remove the now redundant .find_bridge() callback pointer from
usb_acpi_bus.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
When the userspace messaging (for the less common case of userspace key
wrap/unwrap via ecryptfsd) is not needed, allow eCryptfs to build with
it removed. This saves on kernel code size and reduces potential attack
surface by removing the /dev/ecryptfs node.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Modify the request_module to prefix the file system type with "fs-"
and add aliases to all of the filesystems that can be built as modules
to match.
A common practice is to build all of the kernel code and leave code
that is not commonly needed as modules, with the result that many
users are exposed to any bug anywhere in the kernel.
Looking for filesystems with a fs- prefix limits the pool of possible
modules that can be loaded by mount to just filesystems trivially
making things safer with no real cost.
Using aliases means user space can control the policy of which
filesystem modules are auto-loaded by editing /etc/modprobe.d/*.conf
with blacklist and alias directives. Allowing simple, safe,
well understood work-arounds to known problematic software.
This also addresses a rare but unfortunate problem where the filesystem
name is not the same as it's module name and module auto-loading
would not work. While writing this patch I saw a handful of such
cases. The most significant being autofs that lives in the module
autofs4.
This is relevant to user namespaces because we can reach the request
module in get_fs_type() without having any special permissions, and
people get uncomfortable when a user specified string (in this case
the filesystem type) goes all of the way to request_module.
After having looked at this issue I don't think there is any
particular reason to perform any filtering or permission checks beyond
making it clear in the module request that we want a filesystem
module. The common pattern in the kernel is to call request_module()
without regards to the users permissions. In general all a filesystem
module does once loaded is call register_filesystem() and go to sleep.
Which means there is not much attack surface exposed by loading a
filesytem module unless the filesystem is mounted. In a user
namespace filesystems are not mounted unless .fs_flags = FS_USERNS_MOUNT,
which most filesystems do not set today.
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Acked-by: Kees Cook <keescook@chromium.org>
Reported-by: Kees Cook <keescook@google.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=JMlx
-----END PGP SIGNATURE-----
Merge tag 'disintegrate-fbdev-20121220' of git://git.infradead.org/users/dhowells/linux-headers
Pull fbdev UAPI disintegration from David Howells:
"You'll be glad to here that the end is nigh for the UAPI patches.
Only the fbdev/framebuffer piece remains now that the SCSI stuff has
gone in.
Here are the UAPI disintegration bits for the fbdev drivers. It
appears that Florian hasn't had time to deal with my patch, but back
in December he did say he didn't mind if I pushed it forward."
Yay. No more uapi movement. And hopefully no more big header file
cleanups coming up either, it just tends to be very painful.
* tag 'disintegrate-fbdev-20121220' of git://git.infradead.org/users/dhowells/linux-headers:
UAPI: (Scripted) Disintegrate include/video
Pull more VFS bits from Al Viro:
"Unfortunately, it looks like xattr series will have to wait until the
next cycle ;-/
This pile contains 9p cleanups and fixes (races in v9fs_fid_add()
etc), fixup for nommu breakage in shmem.c, several cleanups and a bit
more file_inode() work"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
constify path_get/path_put and fs_struct.c stuff
fix nommu breakage in shmem.c
cache the value of file_inode() in struct file
9p: if v9fs_fid_lookup() gets to asking server, it'd better have hashed dentry
9p: make sure ->lookup() adds fid to the right dentry
9p: untangle ->lookup() a bit
9p: double iput() in ->lookup() if d_materialise_unique() fails
9p: v9fs_fid_add() can't fail now
v9fs: get rid of v9fs_dentry
9p: turn fid->dlist into hlist
9p: don't bother with private lock in ->d_fsdata; dentry->d_lock will do just fine
more file_inode() open-coded instances
selinux: opened file can't have NULL or negative ->f_path.dentry
(In the meantime, the hlist traversal macros have changed, so this
required a semantic conflict fixup for the newly hlistified fid->dlist)
This adds core architecture support for Imagination's Meta processor
cores, followed by some later miscellaneous arch/metag cleanups and
fixes which I kept separate to ease review:
- Support for basic Meta 1 (ATP) and Meta 2 (HTP) core architecture
- A few fixes all over, particularly for symbol prefixes
- A few privilege protection fixes
- Several cleanups (setup.c includes, split out a lot of metag_ksyms.c)
- Fix some missing exports
- Convert hugetlb to use vm_unmapped_area()
- Copy device tree to non-init memory
- Provide dma_get_sgtable()
Signed-off-by: James Hogan <james.hogan@imgtec.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=65cR
-----END PGP SIGNATURE-----
Merge tag 'metag-v3.9-rc1-v4' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag
Pull new ImgTec Meta architecture from James Hogan:
"This adds core architecture support for Imagination's Meta processor
cores, followed by some later miscellaneous arch/metag cleanups and
fixes which I kept separate to ease review:
- Support for basic Meta 1 (ATP) and Meta 2 (HTP) core architecture
- A few fixes all over, particularly for symbol prefixes
- A few privilege protection fixes
- Several cleanups (setup.c includes, split out a lot of
metag_ksyms.c)
- Fix some missing exports
- Convert hugetlb to use vm_unmapped_area()
- Copy device tree to non-init memory
- Provide dma_get_sgtable()"
* tag 'metag-v3.9-rc1-v4' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag: (61 commits)
metag: Provide dma_get_sgtable()
metag: prom.h: remove declaration of metag_dt_memblock_reserve()
metag: copy devicetree to non-init memory
metag: cleanup metag_ksyms.c includes
metag: move mm/init.c exports out of metag_ksyms.c
metag: move usercopy.c exports out of metag_ksyms.c
metag: move setup.c exports out of metag_ksyms.c
metag: move kick.c exports out of metag_ksyms.c
metag: move traps.c exports out of metag_ksyms.c
metag: move irq enable out of irqflags.h on SMP
genksyms: fix metag symbol prefix on crc symbols
metag: hugetlb: convert to vm_unmapped_area()
metag: export clear_page and copy_page
metag: export metag_code_cache_flush_all
metag: protect more non-MMU memory regions
metag: make TXPRIVEXT bits explicit
metag: kernel/setup.c: sort includes
perf: Enable building perf tools for Meta
metag: add boot time LNKGET/LNKSET check
metag: add __init to metag_cache_probe()
...
Pull watchdog updates from Wim Van Sebroeck:
"This contains:
- fixes and improvements
- devicetree bindings
- conversion to watchdog generic framework of the following drivers:
- booke_wdt
- bcm47xx_wdt.c
- at91sam9_wdt
- Removal of old STMP3xxx driver
- Addition of following new drivers:
- new driver for STMP3xxx and i.MX23/28
- Retu watchdog driver"
* git://www.linux-watchdog.org/linux-watchdog: (30 commits)
watchdog: sp805_wdt depends on ARM
watchdog: davinci_wdt: update to devm_* API
watchdog: davinci_wdt: use devm managed clk get
watchdog: at91rm9200: add DT support
watchdog: add timeout-sec property binding
watchdog: at91sam9_wdt: Convert to use the watchdog framework
watchdog: omap_wdt: Add option nowayout
watchdog: core: dt: add support for the timeout-sec dt property
watchdog: bcm47xx_wdt.c: add hard timer
watchdog: bcm47xx_wdt.c: rename wdt_time to timeout
watchdog: bcm47xx_wdt.c: rename ops methods
watchdog: bcm47xx_wdt.c: use platform device
watchdog: bcm47xx_wdt.c: convert to watchdog core api
watchdog: Convert BookE watchdog driver to watchdog infrastructure
watchdog: s3c2410_wdt: Use devm_* functions
watchdog: remove old STMP3xxx driver
watchdog: add new driver for STMP3xxx and i.MX23/28
rtc: stmp3xxx: add wdt-accessor function
watchdog: introduce retu_wdt driver
watchdog: intel_scu_watchdog: fix Kconfig dependency
...
Pull second set of slave-dmaengine updates from Vinod Koul:
"Arnd's patch moves the dw_dmac to use generic DMA binding. I agreed
to merge this late as it will avoid the conflicts between trees.
The second patch from Matt adding a dma_request_slave_channel_compat
API was supposed to be picked up, but somehow never got picked up.
Some patches dependent on this are already in -next :("
* 'next' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: dw_dmac: move to generic DMA binding
dmaengine: add dma_request_slave_channel_compat()
extent cache's slab shrinker which can cause significant, user-visible
pauses when the system is under memory pressure.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=+vcC
-----END PGP SIGNATURE-----
Merge tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 bug fixes from Ted Ts'o:
"Various bug fixes for ext4. The most important is a fix for the new
extent cache's slab shrinker which can cause significant, user-visible
pauses when the system is under memory pressure."
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: enable quotas before orphan cleanup
ext4: don't allow quota mount options when quota feature enabled
ext4: fix a warning from sparse check for ext4_dir_llseek
ext4: convert number of blocks to clusters properly
ext4: fix possible memory leak in ext4_remount()
jbd2: fix ERR_PTR dereference in jbd2__journal_start
ext4: use percpu counter for extent cache count
ext4: optimize ext4_es_shrink()
- Don't allow NFS silly-renamed files to be deleted
- Don't start the retransmission timer when out of socket space
- Fix a couple of pnfs-related Oopses.
- Fix one more NFSv4 state recovery deadlock
- Don't loop forever when LAYOUTGET returns NFS4ERR_LAYOUTTRYLATER
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=FMtb
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-3.9-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
"We've just concluded another Connectathon interoperability testing
week, and so here are the fixes for the bugs that were discovered:
- Don't allow NFS silly-renamed files to be deleted
- Don't start the retransmission timer when out of socket space
- Fix a couple of pnfs-related Oopses.
- Fix one more NFSv4 state recovery deadlock
- Don't loop forever when LAYOUTGET returns NFS4ERR_LAYOUTTRYLATER"
* tag 'nfs-for-3.9-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
SUNRPC: One line comment fix
NFSv4.1: LAYOUTGET EDELAY loops timeout to the MDS
SUNRPC: add call to get configured timeout
PNFS: set the default DS timeout to 60 seconds
NFSv4: Fix another open/open_recovery deadlock
nfs: don't allow nfs_find_actor to match inodes of the wrong type
NFSv4.1: Hold reference to layout hdr in layoutget
pnfs: fix resend_to_mds for directio
SUNRPC: Don't start the retransmission timer when out of socket space
NFS: Don't allow NFS silly-renamed files to be deleted, no signal
Pull btrfs update from Chris Mason:
"The biggest feature in the pull is the new (and still experimental)
raid56 code that David Woodhouse started long ago. I'm still working
on the parity logging setup that will avoid inconsistent parity after
a crash, so this is only for testing right now. But, I'd really like
to get it out to a broader audience to hammer out any performance
issues or other problems.
scrub does not yet correct errors on raid5/6 either.
Josef has another pass at fsync performance. The big change here is
to combine waiting for metadata with waiting for data, which is a big
latency win. It is also step one toward using atomics from the
hardware during a commit.
Mark Fasheh has a new way to use btrfs send/receive to send only the
metadata changes. SUSE is using this to make snapper more efficient
at finding changes between snapshosts.
Snapshot-aware defrag is also included.
Otherwise we have a large number of fixes and cleanups. Eric Sandeen
wins the award for removing the most lines, and I'm hoping we steal
this idea from XFS over and over again."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (118 commits)
btrfs: fixup/remove module.h usage as required
Btrfs: delete inline extents when we find them during logging
btrfs: try harder to allocate raid56 stripe cache
Btrfs: cleanup to make the function btrfs_delalloc_reserve_metadata more logic
Btrfs: don't call btrfs_qgroup_free if just btrfs_qgroup_reserve fails
Btrfs: remove reduplicate check about root in the function btrfs_clean_quota_tree
Btrfs: return ENOMEM rather than use BUG_ON when btrfs_alloc_path fails
Btrfs: fix missing deleted items in btrfs_clean_quota_tree
btrfs: use only inline_pages from extent buffer
Btrfs: fix wrong reserved space when deleting a snapshot/subvolume
Btrfs: fix wrong reserved space in qgroup during snap/subv creation
Btrfs: remove unnecessary dget_parent/dput when creating the pending snapshot
btrfs: remove a printk from scan_one_device
Btrfs: fix NULL pointer after aborting a transaction
Btrfs: fix memory leak of log roots
Btrfs: copy everything if we've created an inline extent
btrfs: cleanup for open-coded alignment
Btrfs: do not change inode flags in rename
Btrfs: use reserved space for creating a snapshot
clear chunk_alloc flag on retryable failure
...
* misc clean-ups in the MTD command-line partitioning parser (cmdlinepart)
* add flash locking support for STmicro chips serial flash chips, as well as
for CFI command set 2 chips.
* new driver for the ELM error correction HW module found in various TI chips,
enable the OMAP NAND driver to use the ELM HW error correction
* added number of new serial flash IDs
* various fixes and improvements in the gpmi NAND driver
* bcm47xx NAND driver improvements
* make the mtdpart module actually removable
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iEYEABECAAYFAlExEs8ACgkQdwG7hYl686Oa+gCgiBNt+I0MiixDeN+MGuE1uw9s
i2wAniD9sR2HDy6y5SkbdXK/aPr8ez/p
=xV1l
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20130301' of git://git.infradead.org/linux-mtd
Pull MTD update from David Woodhouse:
"Fairly unexciting MTD merge for 3.9:
- misc clean-ups in the MTD command-line partitioning parser
(cmdlinepart)
- add flash locking support for STmicro chips serial flash chips, as
well as for CFI command set 2 chips.
- new driver for the ELM error correction HW module found in various
TI chips, enable the OMAP NAND driver to use the ELM HW error
correction
- added number of new serial flash IDs
- various fixes and improvements in the gpmi NAND driver
- bcm47xx NAND driver improvements
- make the mtdpart module actually removable"
* tag 'for-linus-20130301' of git://git.infradead.org/linux-mtd: (45 commits)
mtd: map: BUG() in non handled cases
mtd: bcm47xxnflash: use pr_fmt for module prefix in messages
mtd: davinci_nand: Use managed resources
mtd: mtd_torturetest can cause stack overflows
mtd: physmap_of: Convert device allocation to managed devm_kzalloc()
mtd: at91: atmel_nand: for PMECC, add code to check the ONFI parameter ECC requirement.
mtd: atmel_nand: make pmecc-cap, pmecc-sector-size in dts is optional.
mtd: atmel_nand: avoid to report an error when lookup table offset is 0.
mtd: bcm47xxsflash: adjust names of bus-specific functions
mtd: bcm47xxpart: improve probing of nvram partition
mtd: bcm47xxpart: add support for other erase sizes
mtd: bcm47xxnflash: register this as normal driver
mtd: bcm47xxnflash: fix message
mtd: bcm47xxsflash: register this as normal driver
mtd: bcm47xxsflash: write number of written bytes
mtd: gpmi: add sanity check for the ECC
mtd: gpmi: set the Golois Field bit for mx6q's BCH
mtd: devices: elm: Removes <xx> literals in elm DT node
mtd: gpmi: fix a dereferencing freed memory error
mtd: fix the wrong timeo for panic_nand_wait()
...
Commit cc2383ec06 ("mm: introduce
arch-specific vma flag VM_ARCH_1") merged in v3.7-rc1.
The above commit combined several arch-specific vma flags into one, and
in the process it changed the VM_GROWSUP definition to depend on
specific architectures rather than CONFIG_STACK_GROWSUP. Therefore add
an ifdef for CONFIG_METAG to also set VM_GROWSUP.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Michel Lespinasse <walken@google.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: linux-mm@kvack.org
Meta core internal interrupts (from HWSTATMETA and friends) are vectored
onto the TR1 core trigger for the current thread. This is demultiplexed
in irq-metag.c to individual Linux IRQs for each internal interrupt.
External SoC interrupts (from HWSTATEXT and friends) are vectored onto
the TR2 core trigger for the current thread. This is demultiplexed in
irq-metag-ext.c to individual Linux IRQs for each external SoC interrupt.
The external irqchip has devicetree bindings for configuring the number
of irq banks and the type of masking available.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Cc: Dom Cobley <popcornmix@gmail.com>
Cc: Simon Arlott <simon@fire.lp0.eu>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linux-doc@vger.kernel.org
Add time keeping code for metag. Meta hardware threads have 2 timers.
The background timer (TXTIMER) is used as a free-running time base, and
the interrupt timer (TXTIMERI) is used for the timer interrupt. Both
counters traditionally count at approximately 1MHz.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
The ptrace interface for metag provides access to some core register
sets using the PTRACE_GETREGSET and PTRACE_SETREGSET operations. The
details of the internal context structures is abstracted into user API
structures to both ease use and allow flexibility to change the internal
context layouts. Copyin and copyout functions for these register sets
are exposed to allow signal handling code to use them to copy to and
from the signal context.
struct user_gp_regs (NT_PRSTATUS) provides access to the core general
purpose register context.
struct user_cb_regs (NT_METAG_CBUF) provides access to the TXCATCH*
registers which contains information abuot a memory fault, unaligned
access error or watchpoint. This can be modified to alter the way the
fault is replayed on resume ("catch replay"), or to prevent the replay
taking place.
struct user_rp_state (NT_METAG_RPIPE) provides access to the state of
the Meta read pipeline which can be used to hide memory latencies in
hand optimised data loops.
Extended DSP register state, DSP RAM, and hardware breakpoint registers
aren't yet exposed through ptrace.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Tony Lindgren <tony@atomide.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Some architectures have symbol prefixes and set CONFIG_SYMBOL_PREFIX,
but this wasn't taken into account by the generic cond_syscall. It's
easy enough to fix in a generic fashion, so add the symbol prefix to
symbol names in cond_syscall when CONFIG_SYMBOL_PREFIX is set.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
