Use the pci_info() and pci_err() wrappers for dev_printk() when possible.
Log PCI device vendor and device IDs and BAR information in the same format
used by other architectures.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously we unconditionally requested the legacy VGA framebuffer (bus
address 0xa0000-0xbffff) before we even know what PCI devices are present,
in these paths:
pci_fire_pbm_init, schizo_pbm_init, pci_sun4v_pbm_init, psycho_pbm_init_common
pci_determine_mem_io_space
pci_register_legacy_regions
p->start = mem_res->start + 0xa0000
request_resource(mem_res, p) # claim VGA framebuffer
pci_scan_one_pbm
pci_of_scan_bus # scan DT for PCI devices
pci_claim_bus_resources # claim PCI device BARs
If we found a PCI device with a BAR or bridge window that overlapped the
framebuffer area, we complained about not being able to claim the BAR,
e.g.,
pci 0000:00:01.0: can't claim BAR 8 [mem 0x1ff00000000-0x1ffbfffffff]: address conflict with Video RAM area [??? 0x1ff000a0000-0x1ff000bffff flags 0x80000000]
pci 0000:02:01.0: can't claim BAR 8 [mem 0x1ff00100000-0x1ff028fffff]: no compatible bridge window
pci 0000:03:0f.0: can't claim BAR 8 [mem 0x1ff00100000-0x1ff028fffff]: no compatible bridge window
pci 0000:04:04.0: can't claim BAR 1 [mem 0x1ff02808000-0x1ff02808fff]: no compatible bridge window
This may make the conflicting device unusable because we try not to enable
devices that have unassigned or conflicting BARs, e.g.,
qla1280 0000:04:04.0: can't ioremap BAR 1: [mem size 0x00001000]
qla1280: Unable to map I/O memory
If there is no VGA device in the same PCI segment, there's no reason to
reserve the framebuffer and there's no conflict. If there *is* a VGA
device in the same segment, both the VGA device and the device with an
overlapping BAR may respond to the framebuffer addresses, which may cause
bus errors.
Request the legacy framebuffer area only when we actually find a VGA
device. The fact that VGA devices use the legacy framebuffer even though
it's not reported in a BAR is not sparc-specific, so the reservation of
that area could be made more generic in the PCI core eventually.
Note that on some systems, e.g., Blade 100, we still report a conflict
between an ISA bridge (00:07.0) and a VGA device (00:13.0):
pci_bus 0000:00: root bus resource [mem 0x1ff00000000-0x1ffffffffff] (bus address [0x00000000-0xffffffff])
pci 0000:00:07.0: reg 0x14: [mem 0x1ff00000000-0x1ff000fffff]
pci 0000:00:13.0: can't claim VGA legacy [mem 0x1ff000a0000-0x1ff000bffff]: address conflict with 0000:00:07.0 [mem 0x1ff00000000-0x1ff000fffff]
This is probably harmless, but if the VGA device and something behind the
ISA bridge both responded to reads of the framebuffer, it would cause a bus
error.
Link: https://lkml.kernel.org/r/alpine.LRH.2.21.1804112323170.25495@math.ut.ee
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=117191#c35
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously, pci_register_legacy_regions() reserved PCI address space under
every PCI host bridge for the System ROM and the Video ROM, but these
regions are not part of PCI address space.
Previously, pci_register_legacy_regions() reserved the following areas of
PCI address space under every PCI host bridge:
[bus 0xa0000-0xbffff] Video RAM area (VGA frame buffer)
[bus 0xc0000-0xc7fff] Video ROM
[bus 0xf0000-0xfffff] System ROM
It does need to reserve the [bus 0xa0000-0xbffff] region (at least if
there's a possibility of a VGA device below the bridge) because VGA devices
can respond to that even if they don't describe it with a BAR.
But the Video ROM and System ROM areas don't seem necessary because they
are not areas that legacy PCI devices respond to.
They appear to be copied from x86, where they describe areas of system
memory that depend on BIOS conventions. On x86, BIOS copies the option ROM
of the primary VGA device to RAM at 0xc0000, and the 0xf0000-0xfffff region
is reserved for the motherboard BIOS. Neither of these things applies to
sparc.
Stop reserving the System ROM and Video ROM regions in PCI space.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: David S. Miller <davem@davemloft.net>
Add support for arbitrary bus address offset. Previously we ignored the
child (PCI) address in the "ranges" property and assumed it was always
zero. That means every host bridge window mapped to PCI bus address zero,
e.g.,
pci_bus 0000:00: root bus resource [mem 0x2000000000000-0x200007fffffff] (bus address [0x00000000-0x7fffffff])
But some systems have host bridge windows with non-zero child addresses, so
parse the child address and compute the offset between the parent (CPU) and
child (PCI) addresses. This allows windows like these:
/pci@305: PCI MEM [mem 0x2000000100000-0x200007effffff] offset 2000000000000
pci_sun4v f02ae7f8: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0x2000000100000-0x200007effffff] (bus address [0x00100000-0x7effffff])
[bhelgaas: changelog]
Tested-by: Khalid Aziz <khalid.aziz@oracle.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David reported that a T5-8 sparc system failed to boot with:
pci_sun4v f02dbcfc: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [io 0x804000000000-0x80400fffffff] (bus address [0x0000-0xfffffff])
pci_bus 0000:00: root bus resource [mem 0x800000000000-0x80007effffff] (bus address [0x00000000-0x7effffff])
pci 0000:00:01.0: can't claim BAR 15 [mem 0x100000000-0x4afffffff pref]: no compatible bridge window
Note that we don't know about a host bridge aperture that contains
BAR 15. OF does report a MEM64 aperture, but before this patch,
pci_determine_mem_io_space() ignored it.
Add support for host bridge apertures with 64-bit PCI addresses. Also
set IORESOURCE_MEM_64 for PCI device and bridge resources in PCI 64-bit
memory space.
Sparc doesn't actually print the device and bridge resources, but after
this patch, we should have the equivalent of this:
pci_sun4v f02dbcfc: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [io 0x804000000000-0x80400fffffff] (bus address [0x0000-0xfffffff])
pci_bus 0000:00: root bus resource [mem 0x800000000000-0x80007effffff] (bus address [0x00000000-0x7effffff])
pci_bus 0000:00: root bus resource [mem 0x800100000000-0x8007ffffffff] (bus address [0x100000000-0x7ffffffff])
pci 0000:00:01.0: bridge window [mem 0x800100000000-0x8004afffffff 64bit pref]
[bhelgaas: changelog, URL to David's report]
Fixes: d63e2e1f3d ("sparc/PCI: Clip bridge windows to fit in upstream windows")
Link: http://lkml.kernel.org/r/5514391F.2030300@oracle.com
Reported-by: David Ahern <david.ahern@oracle.com>
Tested-by: David Ahern <david.ahern@oracle.com>
Tested-by: Khalid Aziz <khalid.aziz@oracle.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Semicolons are not necessary after switch/while/for/if braces
so remove them.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the warnings emitted (we fail arch/sparc file
builds with -Werror) were legitimate but harmless, however
one case (n2_pcr_write) was a genuine bug.
Based almost entirely upon a patch by Sam Ravnborg.
Reported-by: Dennis Gilmore <dennis@ausil.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following structure elements duplicate the information in
'struct device.of_node' and so are being eliminated. This patch
makes all readers of these elements use device.of_node instead.
(struct of_device *)->node
(struct dev_archdata *)->prom_node (sparc)
(struct dev_archdata *)->of_node (powerpc & microblaze)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Found by kmemleak.
If request_resource() fails, we leak the struct resource we
allocated to represent the IOMMU mapping area.
This actually happens on sun4v machines because the IOMEM area is only
reported sans the IOMMU region, unlike all previous systems. I'll
need to fix that at some point, but for now fix the leak.
Signed-off-by: David S. Miller <davem@davemloft.net>
When you compile kernel on Sparc64 with heap memory checking and type
"cat /proc/iomem", you get a crash, because pointers in struct
resource are uninitialized.
Most code fills struct resource with zeros, so I assume that it is
responsibility of the caller of request_resource to initialized it,
not the responsibility of request_resource functuion.
After 2.6.29 is out, there could be a check for uninitialized fields
added to request_resource to avoid crashes like this.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Morton wrote:
People keep on doing
printk("%llu", some_u64);
testing it only on x86_64 and this generates a warning storm on
powerpc, sparc64, etc. Because they use `long', not `long long'.
Quite a few 64-bit architectures are using `long' for their
s64/u64 types. We should convert them all to `long long'.
Update types.h so we use unsigned long long for u64 and
fix all warnings in sparc64 code.
Tested with an allnoconfig, defconfig and allmodconfig builds.
This patch introduces additional warnings in several drivers.
These will be dealt with in separate patches.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Move all files from sparc64/kernel/ to sparc/kernel
- rename as appropriate
o Update sparc/Makefile to the changes
o Update sparc/kernel/Makefile to include the sparc64 files
NOTE: This commit changes link order on sparc64!
Link order had to change for either of sparc32 and sparc64.
And assuming sparc64 see more testing than sparc32 change link
order on sparc64 where issues will be caught faster.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
