I've never seen this happen, but it's useful to rule it out.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fix NVM channel attributes. Add indoor-only and GO Concurrent
bits. Remove DFS channel bit which is overlapped with radar.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The nvm_file should be loaded by default for SDIO
procucts only. Change the configuration accordingly.
While at it, fix a typo in the device name.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This allows to use the firmware monitor. This capability
uses a lot of contiguous memory (up to 64MB), so make its
usage module parameter dependent.
The driver will try to allocate as much contiguous memory
as possible downgrading its requirements until the
allocation succeeds.
Dump this data into the fw-error dump file when an error
happens.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This can be useful later for parsing since the parsing may
differ based on the device's family / bus.
Also add the human readable version of the firmware.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
MCS32 is currently not supported, so don't
declare support for it.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Use num of scan channels as advertised by fw TLV.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The low-priority scan feature can be useful, e.g. for OBSS
scans (if those are required by the AP); add back support
for it, restoring the maximum out time to the value it was
for low-priority scan before that was removed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Use ksize to get scan command size instead of calculating it, to
avoid nasty bugs.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The current sched scan channel configuration code
configures all the supported channels for scanning.
However, this can result in SYSASSERT in some cases,
when the configured channel is disabled.
Instead, configure only the channels given in the
req struct, and set the channel_count field appropriately.
While on it, change the code to use channel->hw_value
instead of recalculating the channel number.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The TDLS initiator is set once during link setup. If determines the
address ordering in the link identifier IE.
Fix dependent drivers - mwifiex and mac80211.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using perm_addr is always wrong, it may be reassigned by
anyone using standard netdev APIs. Remove that from the
match function and also use the match function where only
the perm_addr was used now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
drivers/net/wireless/ath/ath9k/main.c:299 ath_reset_internal()
error: we previously assumed 'hchan' could be null (see line 293)
Cc: Felix Fietkau <nbd@openwrt.org>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows new devices users to save some space.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Old devices (A-PHY or B-PHY) are supposed to be supported by b43legacy.
We keep phy_a.c as it's needed for G-PHY which shares some design.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On some platforms, cycles_t is 64-bit, and gcc generates call to
__udivdi3 for straight division of cycles_t/cycles_t. This leads
to compilation failure, as this function is not exist in the kernel
runtime. do_div() to rescue
Original report:
tree: git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next.git master
head: 2e91606f5e
commit: 7c0acf868d [81/103] wil6210: Tx performance monitoring
config: i386-randconfig-ha3-0620 (attached as .config)
All error/warnings:
drivers/built-in.o: In function `wil_vring_debugfs_show':
>> debugfs.c:(.text+0x39b9be): undefined reference to `__udivdi3'
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Why is converting time formats so desired if there are proper
interfaces for this?
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixing following sh-allmodconfig errors reported on kisskb
"
drivers/net/wireless/orinoco/orinoco_cs.c:153:2: error: implicit declaration of function 'ioport_map' [-Werror=implicit-function-declaration]
drivers/net/wireless/orinoco/orinoco_cs.c:205:3: error: implicit declaration of function 'ioport_unmap' [-Werror=implicit-function-declaration]
"
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixing following sh-allmodconfig errors reported on kisskb
"
drivers/net/wireless/libertas/if_cs.c:826:3: error: implicit declaration of function 'ioport_unmap' [-Werror=implicit-function-declaration]
drivers/net/wireless/libertas/if_cs.c:878:2: error: implicit declaration of function 'ioport_map' [-Werror=implicit-function-declaration]
"
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixing following sh-allmodconfig errors reported on kisskb
"
drivers/net/wireless/orinoco/spectrum_cs.c:216:2: error: implicit declaration of function 'ioport_map' [-Werror=implicit-function-declaration]
drivers/net/wireless/orinoco/spectrum_cs.c:273:3: error: implicit declaration of function 'ioport_unmap' [-Werror=implicit-function-declaration]
"
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix checkpatch warning:
WARNING: kfree(NULL) is safe this check is probably not required
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Provide both event (netif_tx_[stop|wake]) tracking via printk;
and state via debugfs 'info'
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Track number of interrupts and Tx/Rx packets;
expose through debugfs 'info'. Reset upon read.
Used to analyse effectivness of interrupt coalescing and NAPI.
Read twice with some interval like
cat info > /dev/null; sleep 1; cat info
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use 'info' debugfs entry for misc. assorted information.
Start with indication whether platform is AC-powered;
will use it later for power related decisions
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are platforms where INTx can't be routed by ACPI,
this leads to pci_enable_device failure. Re-try pretending we have
MSI already configured; in this case pci_enable_device do not try
to configure INTx. However, MSI could still work.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As reported by Dan Carpenter <dan.carpenter@oracle.com>:
The patch a715c7ddd6: "wil6210: improve debug for WMI receive" from
May 29, 2014, leads to the following static checker warning:
drivers/net/wireless/ath/wil6210/wmi.c:746 wmi_recv_cmd()
info: ignoring unreachable code.
drivers/net/wireless/ath/wil6210/wmi.c
739 spin_unlock_irqrestore(&wil->wmi_ev_lock, flags);
740 {
741 int q = queue_work(wil->wmi_wq,
742 &wil->wmi_event_worker);
743 wil_dbg_wmi(wil, "queue_work -> %d\n", q);
744 }
745 }
746 if (n > 1)
^^^^^^^^^^
We never reach this if statemtent.
747 wil_dbg_wmi(wil, "%s -> %d events processed\n", __func__, n);
748 }
Exit loop with "break", not "return".
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
New registers area introduced, mark corresponded address range as valid
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the pcie_bus.c, knowledge about debugfs is not necessary
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For the AP-like interface, if "disconnect all" requested,
every station should be deleted with cfg80211_del_sta().
Implement this behavior.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On Tx path, when vring for the destination not found,
it was considered as error and message was printed unconditionally.
However, this situation is normal after disconnect. If disconnect was while
heavy traffic load, lots of Tx packets will be dropped and this would
cause significant amount of prints in dmesg.
Demote messages priority from 'error' to 'debug'.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Expose operational frequency and link info
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Print to dmesg when FW error notification is about to be sent
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Interrupt threshold registers may be written to.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Usable for debugging, to be able to obtain FW traces
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For performance monitoring, trace time intervals when Tx vring
is idle/not idle. Use CPU cycle counter for this, because jiffies is
too rough, and other precise time measurement methods involve
overhead while get_cycles() should be fast.
This used to provide some estimation for percentage when Tx vring
was idle, i.e. when hardware is under-utilized.
Estimation is not precise because of many reasons - CPU frequency scaling,
grt_cycles() may be per core etc. But still, it is good estimation
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
print used/available counters on debugfs;
print to dmesg when Tx vring becomes empty
This aids with performance investigation
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
print essential info to dmesg
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the wil_cfg80211_start_ap(), debug print selected data:
- beacon (before and after fix-up)
- crypto parameters
- mark start/stop AP invocation
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Inform cfg80211 about Tx result
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Provide 2 files on the debugfs:
- "rxon": write channel (1..4) to open Rx on it, 0 to rxoff
- "tx_mgmt": write binary frame, starting from MAC header
one need to care about turning receiver on/off before/after tx_mgmt
Correct sequence is:
echo $channel > rxon
cat mfmt_frame > tx_mgmt
echo 0 > rxon
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added support for host based bgscan. The h/w queues are blocked
while bgscan is being performed and after coming to the connected
channel, the queues are unblocked.
Signed-off-by: Jahnavi Meher <jahnavi.meher@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Send the QoS null packet via mgmt queue.
Signed-off-by: Jahnavi Meher <jahnavi.meher@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The number of packets being dequeued from s/w queues was fixed -
changed it to a dynamic calculation based on txop. There are also
some fixes to the dequeuing algorithm.
Signed-off-by: Jahnavi Meher <jahnavi.meher@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Changed the SDIO interrupt variables and some clean ups.
Signed-off-by: Jahnavi Meher <jahnavi.meher@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use SGI if configured while sending data packets at a fixed rate.
Signed-off-by: Jahnavi Meher <jahnavi.meher@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Lower level debug messages for some frames and changed confirm
received for rsi_program_bb_rf() to a valid case.
Signed-off-by: Jahnavi Meher <jahnavi.meher@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Made required changes to rsi_set_channel() and rsi_program_bb_rf()
functions.
Signed-off-by: Jahnavi Meher <jahnavi.meher@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Changed the radio caps frame and added the required fields.
Signed-off-by: Jahnavi Meher <jahnavi.meher@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added macros for the endpoints and set the default value of endpoint
to 2.4GHz and 20MHz.
Signed-off-by: Jahnavi Meher <jahnavi.meher@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Changed the function header to match the function name.
Signed-off-by: Jahnavi Meher <jahnavi.meher@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Changed the queue numbers to macros, and corrected the mappings.
Signed-off-by: Jahnavi Meher <jahnavi.meher@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the zeroing function instead of dma_alloc_coherent & memset(,0,)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use seperate tx queue for each AC in each channel context and expose
these information to mac80211 to avoid stopping one channel context
leads to stopping the entire traffic for that AC even on other contexts.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Configure the TSF based hardware timer for a channel switch.
Also set up backup software timer, in case the gen timer fails.
This could be caused by a hardware reset.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TSF time might have been updated by the incoming beacon,
need update the channel switch timer to reflect the change.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In multi channel context (AP + STA case), adjust the TSF time of
the AP chanctx to keep its beacons at half beacon interval offset
relative to the STA chanctx.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update current offchannel duration during scan or roc request.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a basic state machine for switch channel context
for beacon transmission.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Group and set hw state (opmode, primary_sta, beacon conf) per
channel context instead of whole list of vifs. This would allow
each channel context to run in different mode (STA/AP).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Save TSF in channel context for multiple operating channels.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Retrieve appropriate operating channel context while switching
between operating and off channels.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add channel context operations (add, remove, change, assign and
unassign) to enable support for multiple channels.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add remain on channel support in order to enable multi-channel
concurrency.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement hw_scan support for enabling multi-channel cuncurrency.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While leaving from or entering to active channel context, send out
nullfunc frame to inform to the AP about the presence of station.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Force queueing of all frames that belong to a virtual interface on
a different channel context, to ensure that they are sent on the
correct channel.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The channel context worker is used to switch to next requested
channel context.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support to maintain per-channel ACs list.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The channel context structure is defined to enable
multi-channel concurrency support.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since CL_PRINTF only ever takes a single argument, make sure a format
string cannot leak into printk.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix rsi_module_init() to propagate sdio_register_driver() errors.
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
module_usb_driver eliminates the boilerplate and makes the code simpler,
in addition to the fact currently rsi_module_init() ignores usb_deregister() error.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For users who do not need wowlan, load mwifiex.ko with
disconnect_on_suspend = 1; or iw phy0 wowlan disable.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When magic-packet is generated as a UDP packet the offset should
be 20+8 more bytes to cover IPv4 header and UDP header. So the
total offset become 56.
Add a new MEF entry to support both magic-packet patterns
generated by different tools.
Cc: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Zhiyuan Yang <yangzy@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We setup BCN_OFFSET{0,1} registers dynamically, don't have to
initialize them.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
