An hwmod with a 'HWMOD_INIT_NO_IDLE' flag set, is left in
enabled state by the hwmod framework post the initial setup.
Once a real user of the device (a driver) tries to enable it
at a later point, the hwmod framework throws a WARN() about
the device being already in enabled state.
Fix this by introducing a new internal flag '_HWMOD_SKIP_ENABLE' to
identify such devices/hwmods. When the device/hwmod is requested to be
enabled (the first time) by its driver/user, nothing except the
mux-enable is needed. The mux data is board specific and is
unavailable during initial enable() of the device, done by the
framework as part of setup().
A good example of a such a device is an UART used as debug console.
The UART module needs to be kept enabled through the boot, until the
UART driver takes control of it, for debug prints to appear on
the console.
Acked-by: Kevin Hilman <khilman@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: use a flag rather than a state; updated commit message;
edited some documentation]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
By default all registered pads will trigger mpu_irqs[0]. Now there is
an API for selecting used mpu_irq on pad basis, which can be used to
trigger different irq handlers for different pads in the same hwmod.
Each pad that requires its interrupt to be re-routed this way must
have a separate call to omap_hwmod_pad_route_irq(hwmod, pad, irq).
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
[paul@pwsan.com: moved fn to omap_hwmod.c; separated fn from mux scan_wakeups
changes; added kerneldoc]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP mux now parses active wakeup events from pad registers and calls
corresponding hwmod ISRs once a wakeup is detected. This is
accomplished by registering an interrupt handler for PRCM IO event,
which is raised every time the HW detects wakeups.
[paul@pwsan.com: This patch is a merge of Govindraj R's "ARM: OMAP2+:
hwmod: Add API to check IO PAD wakeup status" patch, Tero Kristo's
"ARM: OMAP2+: mux: add support for PAD wakeup interrupts" patch, and
part of Tero's "ARM: OMAP: mux: add support for selecting mpu_irq for
each wakeup pad" patch.]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: Govindraj.R <govindraj.raja@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
[paul@pwsan.com: reduced indentation level; renamed omap_hwmod function;
improved function documentation; modified to iterate only through dynamic
pads; modified to skip pads where idle mode doesn't enable wakeups; split
patches]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Omap_uart_can_sleep function blocks system wide low power state until
uart is active remove this func and add qos requests to prevent
MPU from transitioning.
Keep qos request to default value which will allow MPU to transition
and while uart baud rate is available calculate the latency value
from the baudrate and use the same to hold constraint while uart clocks
are enabled, and if uart is auto-idled the constraint is updated with
default constraint value allowing MPU to transition.
Qos requests are blocking notifier calls so put these requests to
work queue, also the driver uses irq_safe version of runtime API's
and callbacks can be called in interrupt disabled context.
So to avoid warn on slow path warning while using qos update
API's from runtime callbacks use the qos_work_queue.
During bootup the runtime_resume call backs might not be called and runtime
callback gets called only after uart is idled by setting the autosuspend
timeout. So qos_request from runtime resume callback might not activated during
boot if uart baudrate is calculated during bootup for console uart, so schedule
the qos_work queue once we calc_latency while configuring the uart port.
Flush and complete any pending qos jobs in work queue while suspending.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
When using DMA there are two timeouts defined. The first timeout,
rx_timeout, is really a polling rate in which software polls the
DMA status to see if the DMA has finished. This is necessary for
the RX side because we do not know how much data we will receive.
The secound timeout, RX_TIMEOUT, is a timeout after which the
DMA will be stopped if no more data is received. To make this
clearer, rename rx_timeout as rx_poll_rate and rename the
function serial_omap_rx_timeout() to serial_omap_rxdma_poll().
The OMAP-Serial driver defines an RX_TIMEOUT of 3 seconds that is
used to indicate when the DMA for UART can be stopped if no more
data is received. The value is a global definition that is applied
to all instances of the UART.
Each UART may be used for a different purpose and so the timeout
required may differ. Make this value configurable for each UART so
that this value can be optimised for power savings.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
The following UART parameters are defined within the UART driver:
1). Whether the UART uses DMA (dma_enabled), by default set to 0
2). The size of dma buffer (set to 4096 bytes)
3). The time after which the dma should stop if no more data is received.
4). The auto suspend delay that will be passed for pm_runtime_autosuspend
where uart will be disabled after timeout
Different UARTs may be used for different purpose such as the console,
for interfacing bluetooth chip, for interfacing to a modem chip, etc.
Therefore, it is necessary to be able to customize the above settings
for a given board on a per UART basis.
This change allows these parameters to be configured from the board file
and allows the parameters to be configured for each UART independently.
If a board does not define its own custom parameters for the UARTs, then
use the default parameters in the structure "omap_serial_default_info".
The default parameters are defined to be the same as the current settings
in the UART driver to avoid breaking the UART for any cuurnelty supported
boards. By default, make all boards use the default UART parameters.
Signed-off-by: Deepak K <deepak.k@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
From the runtime callbacks enable hwmod wakeups for uart which will
internally enable io-pad wakeups for uarts if they have rx-pad pins
set as wakeup capabale.
Use the io-ring wakeup mechanism after uart clock gating and leave
the PM_WKST set for uart to default reset values cleanup the
code in serial.c which was handling PM_WKST reg.
Irq_chaing(PRM_DRIVER) is used to wakeup uart after uart clocks are gated
using pad wakeup mechanism.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
Move the errata handling mechanism from serial.c to omap-serial file
and utilise the same func in driver file.
Errata i202, i291 are moved to be handled with omap-serial
Moving the errata macro from serial.c file to driver header file
as from on errata will be handled in driver file itself.
Corrected errata id from chapter reference 2.15 to errata id i291.
Removed errata and dma_enabled fields from omap_uart_state struct
as they are no more needed with errata handling done within omap-serial.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Avoid unconditional context restore every time we gate uart
clocks. Check whether context loss happened based on which
we can context restore uart regs from uart_port structure.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
Remove the uart reset function which is configuring the
TX empty irq which can now be handled within omap-serial driver.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add missing uart regs to uart_port structure which can be used in
context restore. Store dll, dlh, mdr1, scr, efr, lcr, mcr reg values
into uart_port structure while configuring individual port in termios
function.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
The mapbase (start_address), membase(io_remap cookie) part of
pdata struct omap_uart_port_info are removed as this should be
derived within driver.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
Currently we use a shared irq handler to identify uart activity and then
trigger a timer. By default the timeout value is zero and can be set or
modified from sysfs. If there was no uart activity for the period set
through sysfs, the timer will expire and call timer handler this will
set a flag can_sleep using which decision to gate uart clocks can be taken.
Since the clock gating mechanism is outside the uart driver, we currently
use this mechanism. In preparation to runtime implementation for omap-serial
driver we can cleanup this mechanism and use runtime API's to gate uart clocks.
Removes the following:
* timer related info from local uart_state struct
* the code used to set timeout value from sysfs.
* irqflags used to set shared irq handler.
* un-used function omap_uart_check_wakeup.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
In preparation to UART runtime conversion remove uart specific calls
from pm24xx/34xx files and their definition from serial.c
These func calls will no more be used with upcoming uart runtime design.
1.) omap_uart_prepare_suspend :- can be taken care with driver suspend hooks.
2.) omap_uart_enable_irqs :- Used to enable/disable uart irq's in suspend
path from PM code, this is removed as same is handled by
uart_suspend_port/uart_resume_port in omap-serial driver which will
do an port_shutdown on suspend freeing irq and port_startup on resume
enabling back irq.
3.) Remove prepare_idle/resume_idle calls used to gate uart clocks.
UART clocks can be gated within driver using runtime funcs
and be woken up using irq_chaining from omap_prm driver.
4.) Remove console_locking from idle path as clock gating is done withing
driver itself with runtime API. Remove is_suspending check used to acquire
console_lock.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds cpu type, macros for identification of TI814X device.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
[tony@atomide.com: left out CK_TI814X for now]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch updates existing macros, functions used for TI816X, to enable
addition of other SoCs belonging to TI81XX family (e.g., TI814X).
The approach taken is to use TI81XX/ti81xx for code/data going to be common
across all TI81XX devices.
cpu_is_ti81xx() is introduced to handle code common across TI81XX devices.
In addition, ti8168_evm_map_io() is now replaced with ti81xx_map_io() and moved
in mach-omap2/common.c as same will be used for TI814X and is not board
specific.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
allow for the omap4430 es2.3 revision to be recognized in the
omap4_check_revision() function.
most aspects of all omap4430 es2.x versions are identical, however
a number of small variations such as default pullup or pulldown
resistor configurations vary between revisions.
detailed information on silicon errata for omap4430 revisions can
be found at http://focus.ti.com/pdfs/wtbu/swpz009D.pdf
Signed-off-by: David Anders <x0132446@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch updates the common machine specific source files for
support for AM33XX/AM335x with cpu type, macros for identification of
AM33XX/AM335X device.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
[tony@atomide.com: updated for map_io and common.h changes, dropped CK_AM33XX]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch updates the common platform files with AM335X device
support (AM33XX family).
The approach taken in this patch is,
AM33XX device will be considered as OMAP3 variant, and a separate
SoC class created for AM33XX family of devices with a subclass type
for AM335X device, which is newly added device in the family.
This means, cpu_is_omap34xx(), cpu_is_am33xx() and cpu_is_am335x()
checks will return success on AM335X device.
A kernel config option CONFIG_SOC_OMAPAM33XX is added under OMAP3
to include support for AM33XX build.
Also, cpu_mask and RATE_IN_XXX flags have crossed 8 bit hence
struct clksel_rate.flags, struct prcm_config.flags and cpu_mask
are changed to u16 from u8.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Hemant Pedanekar <hemantp@ti.com>
[tony@atomide.com: left out CK_AM33XX for now]
Signed-off-by: Tony Lindgren <tony@atomide.com>
On OMAP4 SOC, intecronnects has many write buffers in the async bridges
and they need to be drained before CPU enters into standby state.
Patch 'OMAP4: PM: Add CPUX OFF mode support' added CPU PM support
but OMAP errata i688 (Async Bridge Corruption) needs to be taken
care to avoid issues like system freeze, CPU deadlocks, random
crashes with register accesses, synchronisation loss on initiators
operating on both interconnect port simultaneously.
As per the errata, if a data is stalled inside asynchronous bridge
because of back pressure, it may be accepted multiple times, creating
pointer misalignment that will corrupt next transfers on that data
path until next reset of the system (No recovery procedure once
the issue is hit, the path remains consistently broken).
Async bridge can be found on path between MPU to EMIF and
MPU to L3 interconnect. This situation can happen only when the
idle is initiated by a Master Request Disconnection (which is
trigged by software when executing WFI on CPU).
The work-around for this errata needs all the initiators
connected through async bridge must ensure that data path
is properly drained before issuing WFI. This condition will be
met if one Strongly ordered access is performed to the
target right before executing the WFI. In MPU case, L3 T2ASYNC
FIFO and DDR T2ASYNC FIFO needs to be drained. IO barrier ensure
that there is no synchronisation loss on initiators operating
on both interconnect port simultaneously.
Thanks to Russell for a tip to conver assembly function to
C fuction there by reducing 40 odd lines of code from the patch.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Richard Woodruff <r-woodruff2@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Allocate the memory to save secure ram context which needs
to be done when MPU is hitting OFF mode.
The ROM code expects a physical address to this memory
and hence use memblock APIs to reserve this memory as part
of .reserve() callback. Maximum size as per secure RAM requirements
is allocated.
To keep omap1 build working, omap-secure.h file is created
under plat-omap directory.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds SAR RAM support on OMAP4430. SAR RAM used to save
and restore the HW context in low power modes.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Conflicts:
arch/arm/mach-omap2/board-4430sdp.c
arch/arm/mach-omap2/board-omap4panda.c
arch/arm/mach-omap2/include/mach/omap4-common.h
arch/arm/plat-omap/include/plat/irqs.h
The changes to omap4-common.h were moved to arch/arm/mach-omap2/common.h
and the other trivial conflicts resolved. The now empty ifdef in irqs.h
was also eliminated.
A generic version should replace this later.
As io.c has become nearly empty, omap_init_consistent_dma_size() is moved
into common.c so that io.c can be removed entirely.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Kevin Hilman <khilman@ti.com>
As suggested by Russell King - ARM Linux <linux@arm.linux.org.uk>,
there's no need to keep local prototypes in non-local headers.
Add mach-omap1/common.h and mach-omap2/common.h and move the
local prototypes there from plat/common.h and mach/omap4-common.h.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Provide the OMAP2/3 IRQ code with low level handlers that can be used
by platforms using CONFIG_MULTI_IRQ_HANDLER. Though the handlers are
written in C, the compiled code looks very similar to its assembly
counterpart (at least with my gcc 4.4.1).
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Without this patch we get the following error:
arch/arm/mach-omap2/clkt_dpll.c: In function '_dpll_test_fint':
arch/arm/mach-omap2/clkt_dpll.c:98: error: 'struct dpll_data' has no member named 'flags'
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds a custom DSS reset function used on OMAPs from OMAP2
forward.
The function doesn't actually do a reset, it only waits for the reset to
complete. The reason for this is that on OMAP4 there is no possibility
to do a SW reset, and on OMAP2/3 doing a SW reset for dss_core resets
all the other DSS modules also, thus breaking the HWMOD model where
every DSS module is handled independently.
This fixes the problem with DSS reset on OMAP4, caused by the fact that
because there's no SW reset for dss_core on OMAP4, the HWMOD framework
doesn't try to reset dss_core and thus the DSS clocks were never enabled
at the same time. This causes causes the HWMOD reset to fail for
dss_dispc and dss_rfbi.
The common reset function will also allow us to fix another problem in
the future: before doing a reset we need to disable DSS outputs, which
are in some cases enabled by the bootloader, as otherwise DSS HW seems
to get more or less stuck, requiring a power reset to recover.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[paul@pwsan.com: modified to build arch/arm/mach-omap2/display.o
unconditionally to avoid an error when !CONFIG_OMAP2_DSS]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
There is no use for omap-alsa.h and board-palmz71.c doesn't need it either.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
get_context_loss_count functions return context loss count as u32, and
zero means an error. However, zero is also returned when context has
never been lost and could also be returned when the context loss count
has wrapped and goes to zero.
Change the functions to return an int, with negative value meaning an
error.
OMAP HSMMC code uses omap_pm_get_dev_context_loss_count(), but as the
hsmmc code handles the returned value as an int, with negative value
meaning an error, this patch actually fixes hsmmc code also.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
[tony@atomide.com: updated to fix a warning with recent dmtimer changes]
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'next/cleanup2' of git://git.linaro.org/people/arnd/arm-soc: (31 commits)
ARM: OMAP: Warn if omap_ioremap is called before SoC detection
ARM: OMAP: Move set_globals initialization to happen in init_early
ARM: OMAP: Map SRAM later on with ioremap_exec()
ARM: OMAP: Remove calls to SRAM allocations for framebuffer
ARM: OMAP: Avoid cpu_is_omapxxxx usage until map_io is done
ARM: OMAP1: Use generic map_io, init_early and init_irq
arm/dts: OMAP3+: Add mpu, dsp and iva nodes
arm/dts: OMAP4: Add a main ocp entry bound to l3-noc driver
ARM: OMAP2+: l3-noc: Add support for device-tree
ARM: OMAP2+: board-generic: Add i2c static init
ARM: OMAP2+: board-generic: Add DT support to generic board
arm/dts: Add support for OMAP3 Beagle board
arm/dts: Add initial device tree support for OMAP3 SoC
arm/dts: Add support for OMAP4 SDP board
arm/dts: Add support for OMAP4 PandaBoard
arm/dts: Add initial device tree support for OMAP4 SoC
ARM: OMAP: omap_device: Add a method to build an omap_device from a DT node
ARM: OMAP: omap_device: Add omap_device_[alloc|delete] for DT integration
of: Add helpers to get one string in multiple strings property
ARM: OMAP2+: devices: Remove all omap_device_pm_latency structures
...
Fix up trivial header file conflicts in arch/arm/mach-omap2/board-generic.c
* 'next/pm' of git://git.linaro.org/people/arnd/arm-soc: (66 commits)
ARM: CSR: PM: use outer_resume to resume L2 cache
ARM: CSR: call l2x0_of_init to init L2 cache of SiRFprimaII
ARM: OMAP: voltage: voltage layer present, even when CONFIG_PM=n
ARM: CSR: PM: add sleep entry for SiRFprimaII
ARM: CSR: PM: save/restore irq status in suspend cycle
ARM: CSR: PM: save/restore timer status in suspend cycle
OMAP4: PM: TWL6030: add cmd register
OMAP4: PM: TWL6030: fix ON/RET/OFF voltages
OMAP4: PM: TWL6030: address 0V conversions
OMAP4: PM: TWL6030: fix uv to voltage for >0x39
OMAP4: PM: TWL6030: fix voltage conversion formula
omap: voltage: add a stub header file for external/regulator use
OMAP2+: VC: more registers are per-channel starting with OMAP5
OMAP3+: voltage: update nominal voltage in voltdm_scale() not VC post-scale
OMAP3+: voltage: rename omap_voltage_get_nom_volt -> voltdm_get_voltage
OMAP3+: voltdm: final removal of omap_vdd_info
OMAP3+: voltage: move/rename curr_volt from vdd_info into struct voltagedomain
OMAP3+: voltage: rename scale and reset functions using voltdm_ prefix
OMAP3+: VP: combine setting init voltage into common function
OMAP3+: VP: remove unused omap_vp_get_curr_volt()
...
Fix up trivial conflict in arch/arm/mach-prima2/l2x0.c (code removal vs
edit)
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (33 commits)
iommu/core: Remove global iommu_ops and register_iommu
iommu/msm: Use bus_set_iommu instead of register_iommu
iommu/omap: Use bus_set_iommu instead of register_iommu
iommu/vt-d: Use bus_set_iommu instead of register_iommu
iommu/amd: Use bus_set_iommu instead of register_iommu
iommu/core: Use bus->iommu_ops in the iommu-api
iommu/core: Convert iommu_found to iommu_present
iommu/core: Add bus_type parameter to iommu_domain_alloc
Driver core: Add iommu_ops to bus_type
iommu/core: Define iommu_ops and register_iommu only with CONFIG_IOMMU_API
iommu/amd: Fix wrong shift direction
iommu/omap: always provide iommu debug code
iommu/core: let drivers know if an iommu fault handler isn't installed
iommu/core: export iommu_set_fault_handler()
iommu/omap: Fix build error with !IOMMU_SUPPORT
iommu/omap: Migrate to the generic fault report mechanism
iommu/core: Add fault reporting mechanism
iommu/core: Use PAGE_SIZE instead of hard-coded value
iommu/core: use the existing IS_ALIGNED macro
iommu/msm: ->unmap() should return order of unmapped page
...
Fixup trivial conflicts in drivers/iommu/Makefile: "move omap iommu to
dedicated iommu folder" vs "Rename the DMAR and INTR_REMAP config
options" just happened to touch lines next to each other.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (83 commits)
mmc: fix compile error when CONFIG_BLOCK is not enabled
mmc: core: Cleanup eMMC4.5 conditionals
mmc: omap_hsmmc: if multiblock reads are broken, disable them
mmc: core: add workaround for controllers with broken multiblock reads
mmc: core: Prevent too long response times for suspend
mmc: recognise SDIO cards with SDIO_CCCR_REV 3.00
mmc: sd: Handle SD3.0 cards not supporting UHS-I bus speed mode
mmc: core: support HPI send command
mmc: core: Add cache control for eMMC4.5 device
mmc: core: Modify the timeout value for writing power class
mmc: core: new discard feature support at eMMC v4.5
mmc: core: mmc sanitize feature support for v4.5
mmc: dw_mmc: modify DATA register offset
mmc: sdhci-pci: add flag for devices that can support runtime PM
mmc: omap_hsmmc: ensure pbias configuration is always done
mmc: core: Add Power Off Notify Feature eMMC 4.5
mmc: sdhci-s3c: fix potential NULL dereference
mmc: replace printk with appropriate display macro
mmc: core: Add default timeout value for CMD6
mmc: sdhci-pci: add runtime pm support
...
When device data indicates that multiple block reads are not supported
on a given HSMMC controller instance, log a message to the console, and
pass the appropriate MMC capability flag to the MMC core.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Dave Hylands <dhylands@gmail.com>
Tested-by: Steve Sakoman <sakoman@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
