Most of the adapter initialisation sequences performed in be_resume(),
be_eeh_resume() and be_err_recover() are same. Renamed be_resume() to
be_pci_resume() and moved the common code to a new routine be_resume() to
avoid code duplication.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The steps needed for Lancer's reset/initialization sequence are:
a) wait for SLIPORT_STAUS RDY bit to be set
b) set the SLIPORT_CONTROL IP bit
c) repeat step "a"
The code needed for this sequence is already covered by the be_func_init()
routine (with minor modifications.) So, get rid of the
lancer_test_and_set_rdy_state() and lancer_provisioning_error() routines
that unnecessarily duplicate this code. Also fixed the error recovery
function to take care of these changes
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when an error is detected, the queue resources are being cleaned up
in the recovery routine. The resources are better cleaned up in the error
detection routine itself (similar to EEH code.)
So, this patch re-factors error processing logic to follow the following sequence:
- check if there is an error in adapter
- if error,
- cleanup resources
- attempt recovery
The patch renames lancer_recover_func() to be_err_recover() as this
routine will be used in the future for error recovery on Skyhawk too.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also rename func_recovery_work/task to err_detection_work/task as error
detection is the primary goal of this task while recovery is not guaranteed.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function initialization sequence is executed in be_probe(), be_resume
and be_eeh_resume(). Move this code to a new routine called be_func_init()
to prevent code duplication.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the code to fetch the adapter state is in be_setup()->be_get_config().
So, move the code from be_get_initial_config() to be_get_config().
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The members of be_adapter struct were being allocated in two separate
routines -- be_ctrl_init() and be_stats_init(). Also, some other members
were allocated elsewhere. This patch moves the alloc/free code into
be_drv_init/cleanup() routines. The be_pci_map_bars() routine that was
called from be_ctrl_init() is now called directly from be_probe().
The new routine be_drv_init() will now be the place-holder for allocating
memory for any new be_adapter{} members in the future.
Some routines needed to be moved to provide forward definitions for their
calls.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the BNA driver version to 3.2.25.1 and the firmware version
to 3.2.5.1
Signed-off-by: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An error return from __vnet_tx_trigger() sets the TX descriptor to
VIO_DESC_FREE while leaving port->tx_bufs[txi].skb set. This leads
to a BUG_ON() the next time this descriptor is used.
This patch frees the pending skb when getting a trigger error to
match the VIO_DESC_FREE state.
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts all __raw_readl and __raw_writel function calls
to their corresponding readl_relaxed and writel_relaxed variants.
It also tells the driver to set ahb_endian_swp_mgmt_en bit in dma_cfg
when the CPU is configured in big endian mode.
Signed-off-by: Arun Chandran <achandran@mvista.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates BNX2 driver version to 2.2.6 and CNIC driver version
to 2.5.21.
Signed-off-by: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not enable filter SORT MODE in chip init routine. This patch addresses an
issue where BCM5716 sporadically drops packets when changing multicast list.
Signed-off-by: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides additional changes as a part of BNX2 and CNIC driver
re-branding effort.
Signed-off-by: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- To avoid multiple accesses to CQE, extract compl_status and end_idx from
be_tx_compl_get().
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Reduce code duplication by moving WRB-frags setup into a function.
- Do not setup WRB-header before frags are setup, which is unncessary if
there's errors while setting up frags. We should only grab an entry for
the header, setup the frags and if everything is fine setup the header.
- The error cleanup can be moved into a small function.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The WRB header is setup by wrb_fill_hdr() routine. This routine currently
gets some of the WRB params as args and figures out rest of the WRB params
by looking at various fields in skb (like gso, checksum, vlan-tag etc).
All these params could instead be retrieved from the skb into a structure
and passed to this routine. This separates wrb_fill_hdr() to only provide
chip-specific code to fill the WRB. This also makes it simple to support
chips with different WRB formats.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This debug output is not really an error message since mac reset can fail
if the phy clocks are gated, specifically when the phy has been placed in
a powered down or isolation mode. The netdev output masks were changed from
err to dbg, and comments added in the code.
Signed-off-by: Vince Bridgers <vbridger@opensource.altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change use of Altera TSE's MDIO access from phy 0 registers to phy 1
registers. This allows support for GMII, MII, RGMII, and SGMII
designs where the external PHY is always accesible through
Altera TSE's MDIO phy 1 registers and Altera's PCS is accessible
through MDIO phy 0 registers for SGMII applications.
Signed-off-by: Vince Bridgers <vbridger@opensource.altera.com>
Tested-by: Kai Lin Ng <kailng@altera.com>
Tested-by: Dalon Westergreen <dwesterg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Missing netlink attribute validation in nft_lookup, from Patrick
McHardy.
2) Restrict ipv6 partial checksum handling to UDP, since that's the
only case it works for. From Vlad Yasevich.
3) Clear out silly device table sentinal macros used by SSB and BCMA
drivers. From Joe Perches.
4) Make sure the remote checksum code never creates a situation where
the remote checksum is applied yet the tunneling metadata describing
the remote checksum transformation is still present. Otherwise an
external entity might see this and apply the checksum again. From
Tom Herbert.
5) Use msecs_to_jiffies() where applicable, from Nicholas Mc Guire.
6) Don't explicitly initialize timer struct fields, use setup_timer()
and mod_timer() instead. From Vaishali Thakkar.
7) Don't invoke tg3_halt() without the tp->lock held, from Jun'ichi
Nomura.
8) Missing __percpu annotation in ipvlan driver, from Eric Dumazet.
9) Don't potentially perform skb_get() on shared skbs, also from Eric
Dumazet.
10) Fix COW'ing of metrics for non-DST_HOST routes in ipv6, from Martin
KaFai Lau.
11) Fix merge resolution error between the iov_iter changes in vhost and
some bug fixes that occurred at the same time. From Jason Wang.
12) If rtnl_configure_link() fails we have to perform a call to
->dellink() before unregistering the device. From WANG Cong.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (39 commits)
net: dsa: Set valid phy interface type
rtnetlink: call ->dellink on failure when ->newlink exists
com20020-pci: add support for eae single card
vhost_net: fix wrong iter offset when setting number of buffers
net: spelling fixes
net/core: Fix warning while make xmldocs caused by dev.c
net: phy: micrel: disable NAND-tree for KSZ8021, KSZ8031, KSZ8051, KSZ8081
ipv6: fix ipv6_cow_metrics for non DST_HOST case
openvswitch: Fix key serialization.
r8152: restore hw settings
hso: fix rx parsing logic when skb allocation fails
tcp: make sure skb is not shared before using skb_get()
bridge: netfilter: Move sysctl-specific error code inside #ifdef
ipv6: fix possible deadlock in ip6_fl_purge / ip6_fl_gc
ipvlan: add a missing __percpu pcpu_stats
tg3: Hold tp->lock before calling tg3_halt() from tg3_init_one()
bgmac: fix device initialization on Northstar SoCs (condition typo)
qlcnic: Delete existing multicast MAC list before adding new
net/mlx5_core: Fix configuration of log_uar_page_sz
sunvnet: don't change gso data on clones
...
Pull debugfs patches from Al Viro:
"debugfs patches, mostly to make it possible for something like tracefs
to be transparently automounted on given directory in debugfs.
New primitive in there is debugfs_create_automount(name, parent, func,
arg), which creates a directory and makes its ->d_automount() return
func(arg). Another missing primitive was debugfs_create_file_size() -
open-coded in quite a few places. Dave's patch adds it and converts
the open-code instances to calling it"
* 'debugfs_automount' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
debugfs: Provide a file creation function that also takes an initial size
new primitive: debugfs_create_automount()
debugfs: split end_creating() into success and failure cases
debugfs: take mode-dependent parts of debugfs_get_inode() into callers
fold debugfs_mknod() into callers
fold debugfs_create() into caller
fold debugfs_mkdir() into caller
debugfs_mknod(): get rid useless arguments
fold debugfs_link() into caller
debugfs: kill __create_file()
debugfs: split the beginning and the end of __create_file() off
debugfs_{mkdir,create,link}(): get rid of redundant argument
Pull misc VFS updates from Al Viro:
"This cycle a lot of stuff sits on topical branches, so I'll be sending
more or less one pull request per branch.
This is the first pile; more to follow in a few. In this one are
several misc commits from early in the cycle (before I went for
separate branches), plus the rework of mntput/dput ordering on umount,
switching to use of fs_pin instead of convoluted games in
namespace_unlock()"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
switch the IO-triggering parts of umount to fs_pin
new fs_pin killing logics
allow attaching fs_pin to a group not associated with some superblock
get rid of the second argument of acct_kill()
take count and rcu_head out of fs_pin
dcache: let the dentry count go down to zero without taking d_lock
pull bumping refcount into ->kill()
kill pin_put()
mode_t whack-a-mole: chelsio
file->f_path.dentry is pinned down for as long as the file is open...
get rid of lustre_dump_dentry()
gut proc_register() a bit
kill d_validate()
ncpfs: get rid of d_validate() nonsense
selinuxfs: don't open-code d_genocide()
Provide a file creation function that also takes an initial size so that the
caller doesn't have to set i_size, thus meaning that we don't have to call
deal with ->d_inode in the callers.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The patch "module: fix types of device tables aliases" newly requires that
invocations of
MODULE_DEVICE_TABLE(type, name);
come *after* the definition of `name'. That is reasonable, but some
drivers weren't doing this. Fix them.
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Andrey Ryabinin <a.ryabinin@samsung.com>
Cc: David Miller <davem@davemloft.net>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
printk and friends can now format bitmaps using '%*pb[l]'. cpumask
and nodemask also provide cpumask_pr_args() and nodemask_pr_args()
respectively which can be used to generate the two printf arguments
necessary to format the specified cpu/nodemask.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
tg3_init_one() calls tg3_halt() without tp->lock despite its assumption
and causes deadlock.
If lockdep is enabled, a warning like this shows up before the stall:
[ BUG: bad unlock balance detected! ]
3.19.0test #3 Tainted: G E
-------------------------------------
insmod/369 is trying to release lock (&(&tp->lock)->rlock) at:
[<ffffffffa02d5a1d>] tg3_chip_reset+0x14d/0x780 [tg3]
but there are no more locks to release!
tg3_init_one() doesn't call tg3_halt() under normal situation but
during kexec kdump I hit this problem.
Fixes: 932f19de ("tg3: Release tp->lock before invoking synchronize_irq()")
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Northstar (Broadcom's ARM architecture) we need to manually enable
all cores. Code for that is already in place, but the condition for it
was wrong.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver keeps adding multicast addresses without deleting removed MACs and
worrying about adapters filter limit. This results into actual count of programmed
multicast addresses get accumulated over the time and overruns the adapter's
filter limit without putting device in ACCEPT_ALL_MULTI mode. This causes
newly added multicast traffic to fail after the sequence of addition - deletion
in certain pattern.
This issue is seen only when netdev's mcast list count is less than adapters
mcast filter limit.
e.g. If adapters multicast filter limit is 38 per function
then following sequence would result in multicast traffic failure for
newly added MACs.
- add less than 38 multicast MACs
- remove previously added multicast MACs
- add new multicast MACs (less than 38)
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code failed to configure the page size for architectures with page
size different than 4K - PPC for example.
Signed-off-by: Carol L Soto <clsoto@us.ibm.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch unclones an skb for the case where the sunvnet driver needs to
change the segmentation size so that it doesn't interfere with TCP SACK's
use of them.
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the use of functions setup_timer
and mod_timer.
This is done using Coccinelle and semantic patch used
for this as follows:
// <smpl>
@@
expression x,y,z,a,b;
@@
-init_timer (&x);
+setup_timer (&x, y, z);
+mod_timer (&a, b);
-x.function = y;
-x.data = z;
-x.expires = b;
-add_timer(&a);
// </smpl>
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_NET_XGENE=y but CONFIG_OF=n:
drivers/net/ethernet/apm/xgene/xgene_enet_main.c:1033: warning: ‘xgene_enet_of_match’ defined but not used
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is only an API consolidation and should make things more readable.
Converting milliseconds to jiffies by "val * HZ / 1000" is technically
OK but msecs_to_jiffies(val) is the cleaner solution and handles all
corner cases correctly. This is a minor API cleanup only.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the normal {} instead of a macro to terminate an array.
Remove the macro too.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the normal {} instead of a macro to terminate an array.
Remove the macro too.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) More iov_iter conversion work from Al Viro.
[ The "crypto: switch af_alg_make_sg() to iov_iter" commit was
wrong, and this pull actually adds an extra commit on top of the
branch I'm pulling to fix that up, so that the pre-merge state is
ok. - Linus ]
2) Various optimizations to the ipv4 forwarding information base trie
lookup implementation. From Alexander Duyck.
3) Remove sock_iocb altogether, from CHristoph Hellwig.
4) Allow congestion control algorithm selection via routing metrics.
From Daniel Borkmann.
5) Make ipv4 uncached route list per-cpu, from Eric Dumazet.
6) Handle rfs hash collisions more gracefully, also from Eric Dumazet.
7) Add xmit_more support to r8169, e1000, and e1000e drivers. From
Florian Westphal.
8) Transparent Ethernet Bridging support for GRO, from Jesse Gross.
9) Add BPF packet actions to packet scheduler, from Jiri Pirko.
10) Add support for uniqu flow IDs to openvswitch, from Joe Stringer.
11) New NetCP ethernet driver, from Muralidharan Karicheri and Wingman
Kwok.
12) More sanely handle out-of-window dupacks, which can result in
serious ACK storms. From Neal Cardwell.
13) Various rhashtable bug fixes and enhancements, from Herbert Xu,
Patrick McHardy, and Thomas Graf.
14) Support xmit_more in be2net, from Sathya Perla.
15) Group Policy extensions for vxlan, from Thomas Graf.
16) Remove Checksum Offload support for vxlan, from Tom Herbert.
17) Like ipv4, support lockless transmit over ipv6 UDP sockets. From
Vlad Yasevich.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1494+1 commits)
crypto: fix af_alg_make_sg() conversion to iov_iter
ipv4: Namespecify TCP PMTU mechanism
i40e: Fix for stats init function call in Rx setup
tcp: don't include Fast Open option in SYN-ACK on pure SYN-data
openvswitch: Only set TUNNEL_VXLAN_OPT if VXLAN-GBP metadata is set
ipv6: Make __ipv6_select_ident static
ipv6: Fix fragment id assignment on LE arches.
bridge: Fix inability to add non-vlan fdb entry
net: Mellanox: Delete unnecessary checks before the function call "vunmap"
cxgb4: Add support in cxgb4 to get expansion rom version via ethtool
ethtool: rename reserved1 memeber in ethtool_drvinfo for expansion ROM version
net: dsa: Remove redundant phy_attach()
IB/mlx4: Reset flow support for IB kernel ULPs
IB/mlx4: Always use the correct port for mirrored multicast attachments
net/bonding: Fix potential bad memory access during bonding events
tipc: remove tipc_snprintf
tipc: nl compat add noop and remove legacy nl framework
tipc: convert legacy nl stats show to nl compat
tipc: convert legacy nl net id get to nl compat
tipc: convert legacy nl net id set to nl compat
...
This patch fixes indentation issue and error found in argument
reported by static analysis. Without this patch, sparse and other
static analysis errors will be found.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-02-09
This series contains updates to i40e and i40evf only.
Rickard Strandqvist removes an unused function for i40e.
John Linville reorders a piece of code so that y_budget does not get used
by the FCoE code before it gets initialized.
Mitch adds a delay after VF reset with a minimum of 10ms to allow the
hardware internal FIFOs to flush. Bumps up the ARQ descriptors, since
we can easily overrun the PF's admin receive queue. Added locking around
the VF reset code, since during VF deallocation, we cannot depend on
simply masking the interrupt since this does not lock out the service task,
which can still call the reset routine. Fix a potential multi-minute
delay on driver unload, VF disable or system shutdown. When the module
is being unloaded, waiting for the PF to politely handle all of our admin
queue requests might take forever with a lot of VFs enabled, so just
stop everything and request a VF reset. Also stops the watchdog during
shutdown to prevent a log full of admin queue errors and the occasional
hang when the system is shut down.
Anjali forces Tx descriptor writebacks on ITR by kicking off the SWINT
interrupt since we noticed that there are non-cache-aligned Tx
descriptors waiting in the ring while interrupts are disabled under NAPI.
Enables loopback for the FCoE VSI, so that VSIs can directly talk to each
other without going out on the wire.
Matthew fixes an LED blink issue by making sure to clear the GPIO blink
field, instead of OR'ing against zero if the field is already '1'.
Greg cleans up a function header comment.
Vasu helps biosdevname user tool to differentiate dev_port for PCoE netdev
and PF netdev, by setting different dev_port value for FCoE netdev.
Carolyn adds a call to u64_stats_init to the receive setup in order to
avoid lockdep errors with seqcount on newer kernels.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The vunmap() function performs also input parameter validation.
Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to get option/expansion rom version flashed in the adapter via
ethtool getdrvinfo function.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a call to u64_stats_init to Rx setup.
This done in order to avoid lockdep errors with seqcount on newer kernels.
Change-ID: Ia8ba8f0bcbd1c0e926f97d70aeee4ce4fd055e93
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For all VSIs on a VEB, Loopback mode should be either on or off.
Our configuration requires them to be ON so that VSIs can directly
talk to each other without going out on the wire.
Change-ID: I77b8310bc846329972b13b185949ab1431a46c30
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set different dev_port value 1 for FCoE netdev than the default zero
dev_port value for PF netdev, this helps biosdevname user tool to
differentiate them correctly while both attached to the same PCI
function.
Change-ID: I8fb90e4ef52a1242f7580e49a3f0918735aee8ef
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make sure to clear the GPIO blink field, instead of OR'ing against zero
if the field is already '1'.
Change-ID: Ie52a52abd48f6f52b20778a6b8b0c542dfc9245c
Signed-off-by: Matt Jared <matthew.a.jared@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch forces Tx descriptor writebacks on ITR by kicking
off the SWINT interrupt when we notice that there are non-cache-aligned
Tx descriptors waiting in the ring while interrupts are disabled
under NAPI.
Change-ID: dd6d9675629bf266c7515ad7a201394618c35444
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Stop the service task in the shutdown handler, preventing it from
accessing the admin queue after it had been closed. This fixes a panic
that could occur when the system was shut down with a lot of VFs
enabled.
Change-ID: I286735e3842de472385bbf7ad68d30331e508add
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Stop the watchdog during shutdown. Failing to do this causes a log full
of admin queue errors and the occasional hang when the system is shut
down.
Change-ID: Ib2fd11213cca2fa589eb68577e86b1000c23c250
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Occasionally on shutdown, the FW will hand us a bunch of messages filled
with zeros, which can cause us to spin trying to handle them. Just
ignore these and get on with shutting down.
Change-ID: I347e9648f7153ad5a7b7e0847b87f7aad5f3e0da
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the module is being unloaded, don't wait for the PF to politely
handle all of our admin queue requests, as that might take forever with
a lot of VFs enabled. Instead, just stop everything and request a VF
reset.
When the original shutdown code was written, VF resets were unreliable,
so we avoided them. But with production hardware and firmware, and the
1.x PF driver, this is no longer the case.
This fixes a potential multi-minute delay on driver unload, VF disable,
or system shutdown.
Change-ID: Ib43d6d860ef6b9b8f26e8dce0615a0302608c7d9
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During VF deallocation, we need to lock out the VF reset code. However,
we cannot depend on simply masking the interrupt, as this does not lock
out the service task, which can still call the reset routine. Instead,
leave the interrupt enabled, but add locking around the VF disable and
reset routines.
For the disable code, we wait to get the lock, as the reset code will
take a finite amount of time to run. For the reset code, we just return
if we fail to get the lock. Since we know that the VFs are being
disabled, we don't need to handle the reset.
This fixes a panic when disabling SR-IOV.
Change-ID: Iea0a6cdef35c331f48c6d5b2f8e6f0e86322e7d8
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When enabling 64 VFs and loading the VF driver in the host kernel, we
can easily overrun the PF's admin receive queue. Double the size of this
queue, and increase the work limit to allow the PF to handle more
requests in a single pass through the service task.
Change-ID: I0efbbdc61954bffad422a2f33c4b948a59370bf5
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Delay a minimum of 10ms after VF reset, to allow the hardware's internal
FIFOs to flush.
Change-ID: I8a02ddb28c9f0d7303a1eb21d0b2443e5b4c1cda
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This I40E_FCOE block increments v_budget before it has been initialized,
then v_budget gets overwritten a few lines later. This patch just
reorders the code hunks in what I believe was the intended sequence.
Coverity: CID 1260099
Signed-off-by: John W Linville <linville@tuxdriver.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the function i40e_rx_is_fip() that is not used anywhere.
This was partially found by using a static code analysis program
called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Dump Transport Processor modules congestion control configuration
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support to dump the current contents of mailbox and the driver which owns
it.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dump out various chip sensor information. Currently Chip Temperature
and Core Voltage.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 32-bit fields of a tx-wrb are little endian. The driver is currently
using be_dws_le_to_cpu() routine to swap (cpu to le) all the fields of
a tx-wrb. So, the rsvd field is also unnecessarily swapped.
This patch fixes this by individually swapping the required fields.
Also, the type of the fields in eth_tx_wrb{} is now changed to __le32
from u32 to avoid sparse warnings.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for processing the port misconfigure async
event generated by the FW. This event is generated typically when an
optical module is incorrectly installed or is faulty.
This patch also moves the port_name field to the adapter struct for
logging the event. As the be_cmd_query_port_name() call is now moved
to be_get_config(), it is modified to use the mailbox instead of MCCQ
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch re-factors the filter setting (uc-list, mc-list, promisc, vlan)
code in be_set_rx_mode() and be_vid_config() to make it more readable
and reduce code duplication.
This patch adds a separate field to track the state/mode of filtering,
along with moving all the filtering related fields to one place in be
be_adapter structure.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch passes BE_IF_FLAGS_XXX flags to be_cmd_rx_filter() routine
instead of the IFF_XXX flags. Doing this gets rid of the code to convert
the IFF_XXX flags to the BE_IF_FLAGS_XXX used by the FW cmd. The patch
also removes code for setting if_flags_mask that was duplicated for each
filter mode.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While sending FW update cmds to the FW, the driver specifies the "type"
of each component that needs to be flashed. The FW then picks the offset
in the flash area at which the componnet is to be flashed. This doesn't work
when new components that the current FW doesn't recognize, need to be
flashed. Recent FWs (10.2 and above) support a scheme of FW-update wherein
the "offset" of the component in the flash area can be specified instead
of the "type". This patch uses the "offset" based FW-update mechanism and
only when it fails, it fallsback to the old "type" based update.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Skyhawk-B0 FW UFI is not compatible to flash on Skyhawk-P2 ASIC.
But, Skyhawk-P2 FW UFI is compatible with both B0 and P2 chips.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch re-factors the code that checks for flash file compatibility with
the chip type, for better readability, as follows:
- be_get_ufi_type() returns the UFI type from the flash file
- be_check_ufi_compatibility() checks if the UFI type is compatible
with the adapter/chip that is being flashed
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BIT(x) is the preffered usage.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Routines that are called only inside one src file must remain in that
file itself. Including them in a header file that is used for exporting
routine/struct definitions, causes unnecessary compilation of other
src files, when such a routine is modified.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using per channel DMA interrupts the transmit interrupt (TI) and the
receive interrupt (RI) are masked off so as to not generate an interrupt
to the main ISR. However, should another interrupt fire for the DMA channel
that is handled by the main ISR the TI/RI bits can still be set. This
will cause the wrong and uninitialized napi structure to be used causing a
panic. Add a check to be sure per channel DMA interrupts are not enabled
before acting on those bit flags.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a couple bugs with the error handling in this function.
1) If we can't allocate "rx_ring->rx_skbuff" then we should call
dma_free_coherent() but we don't.
2) free_rx_ring() frees "rx_ring->rx_skbuff_dma" and "rx_ring->rx_skbuff"
so calling it in a loop causes a double free.
Also it was a bit confusing how we sometimes freed things before doing
the goto. I've cleaned it up so it does error handling in normal kernel
style.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables the ethertype Anti-Spoofing feature for affected
devices. It is configured such that LLDP packets sent by a VF will
be dropped.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change combines the reset and watchdog tasklets into a single task.
The advantage of this is that we can avoid multiple schedules of the reset
task when we have a reset event needed due to either the mailbox going down
or transmit packets being present on a link down.
CC: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up the logic dealing with link down/up by breaking down the
link detection and up/down events into separate functions - similar to how these
events are handled in other drivers.
CC: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds code to allow for Tx hang checking. The idea is to provide
more robust debug info in the event of a transmit unit hang. Similar to the
logic in ixgbe.
CC: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch updates the ordering of the shutdown path so that we attempt to
shutdown the rings more gracefully. Basically the big changes are that we
shutdown the main Rx filter in the case of Rx and we set the carrier_off
state in the case of Tx so that packets stop being delivered from outside
the driver. Then we shut down interrupts and NAPI. Finally we stop the
rings from performing DMA and clean them. This is a bit more graceful than
the previous path.
CC: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clean up the setting of vlan_features by enabling all features at once.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support VXLAN receive checksum offload in X550 hardware.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We always identify the PHY in our reset_hw path anyway so there is
no need to do it in get_invariants(). The reason I even noticed this
is that for new hardware (X550em) we don't assign some methods until
later in probe and calling phy.ops.read_reg could lead to a panic.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
My original patch 6a14ee0cfb "ixgbe: Add X550 support function pointers"
accidental set a default value for this structure member twice.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes couple of issues introduced by
commit 2b509c0cd2 ("ixgbe: cleanup ixgbe_ndo_set_vf_vlan")
- fix setting of the VLAN inside ixgbe_enable_port_vlan()
- disable the "hide VLAN" bit in PFQDE when port VLAN is disabled
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X550 provides RSS registers for configuring RSS per VF.
This patch introduces ixgbevf_setup_vfmrqc() which uses the VFRETA,
VFRSSRK and VFMRQC registers to configure RSS on X550.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables multiple queues and RSS support for the VF.
Maximum of 2 queues are supported due to available vectors.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ixgbe_set_sriov_queues() has the logic to allow multiple queues, this patch
just removes the limitation.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up prototypes that should have been defined
as static.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix two cases where variables are being set but not used.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh<Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, fm10k_update_xc_addr_pf has an issue where it does not
properly drop the upper-most four bits of the VLAN ID due to type
promotion. Resolve the issue not by masking off the bits, but by
throwing an error if the VLAN ID is out-of-bounds.
Reported-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
this patch fixes following sparse warning:
vxge-config.c:4640:30: warning: Using plain integer as NULL pointer
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch fixes following sparse warning:
macb.c:2038:26: warning: symbol 'gem_ethtool_ops' was not declared. Should it be static?
Alongside drops exporting of gem_ethtool_ops as there is no need.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch fixes following sparse warnings:
bnx2x_main.c:9172:6: warning: symbol 'bnx2x_stop_ptp' was not declared. Should it be static?
bnx2x_main.c:13321:6: warning: symbol 'bnx2x_register_phc' was not declared. Should it be static?
bnx2x_main.c:14638:5: warning: symbol 'bnx2x_enable_ptp_packets' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch fixes following sparse warnings:
enic_main.c:92:28: warning: symbol 'mod_table' was not declared. Should it be static?
enic_main.c:109:28: warning: symbol 'mod_range' was not declared. Should it be static?
enic_main.c:1306:5: warning: symbol 'enic_busy_poll' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch fixes following sparse warning:
enic_ethtool.c:95:6: warning: symbol 'enic_intr_coal_set_rx' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch fixes following sparse warning:
be_cmds.c:2750:5: warning: symbol 'be_cmd_set_qos' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch fixes following sparse warning:
cxgb4_dcb.c:25:6: warning: symbol 'dcb_ver_array' was not declared. Should it be static?
Alongside making it const.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/vxlan.c
drivers/vhost/net.c
include/linux/if_vlan.h
net/core/dev.c
The net/core/dev.c conflict was the overlap of one commit marking an
existing function static whilst another was adding a new function.
In the include/linux/if_vlan.h case, the type used for a local
variable was changed in 'net', whereas the function got rewritten
to fix a stacked vlan bug in 'net-next'.
In drivers/vhost/net.c, Al Viro's iov_iter conversions in 'net-next'
overlapped with an endainness fix for VHOST 1.0 in 'net'.
In drivers/net/vxlan.c, vxlan_find_vni() added a 'flags' parameter
in 'net-next' whereas in 'net' there was a bug fix to pass in the
correct network namespace pointer in calls to this function.
Signed-off-by: David S. Miller <davem@davemloft.net>
