In gsi_irq_setup(), two registers are written with the intention of
disabling inter-EE channel and event IRQs.
But the wrong registers are used (and defined); the ones used are
read-only registers that indicate whether the interrupt condition is
present.
Define the mask registers instead of the status registers, and use
them to disable the inter-EE interrupt types.
Fixes: 46f748ccaf ("net: ipa: explicitly disallow inter-EE interrupts")
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20210505223636.232527-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
IPA initialization includes loading some firmware. This step is
done either by the modem or by the AP under Trust Zone. If the
AP loads firmware, the name of the firmware file is currently
hard-coded ("ipa_fws.mdt").
Add the ability to specify the relative path of the firmware file to
use in a property in the Device Tree IPA node. If the property is
not found (or if any other error occurs attempting to get it), fall
back to using a default relative path.
Use the "old" fixed name as the default. Rename the symbol that
represents this default to emphasize its purpose.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the SM8350 SoC, which includes IPA version 4.9.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the SC7280 SoC, which includes IPA version 4.11.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the SDX55 SoC, which includes IPA version 4.5.
Starting with IPA v4.5, a few of the memory regions have a different
number of "canary" values; update comments in the where the region
identifers are defined to accurately reflect that.
I'll note three differences in SDX55 versus the other two existing
platforms (SDM845 and SC7180):
- SDX55 uses a 32-bit Linux kernel
- SDX55 has four interconnects rather than three
- SDX55 uses IPA v4.5, which uses inline checksum offload
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Checksum offload for IPA v4.5+ is implemented differently, using
"inline" offload (which uses a common header format for both upload
and download offload).
The IPA hardware must be programmed to enable MAP checksum offload,
but the RMNet driver is responsible for interpreting checksum
metadata supplied with messages.
Currently, the RMNet driver does not support inline checksum offload.
This support is imminent, but until it is available, do not allow
newer versions of IPA to specify checksum offload for endpoints.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some time ago changes were made to stop referring to clearing the
hardware pipeline as a "tag process." Fix a comment to use the
newer terminology.
Get rid of a pointless double-negation of the Boolean toward_ipa
flag in ipa_endpoint_config().
make ipa_endpoint_exit_one() private; it's only referenced inside
"ipa_endpoint.c".
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are place holder functions in the GSI code that do nothing.
Remove these, knowing we can add something back in their place if
they're really needed someday.
Some of these are inverse functions (such as teardown to match setup).
Explicitly comment that there is no inverse in these cases.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are place holder functions in the IPA code that do nothing.
For the most part these are inverse functions, for example, once the
routing or filter tables are set up there is no need to perform any
matching teardown activity at shutdown, or in the case of an error.
These can be safely removed, resulting in some code simplification.
Add comments in these spots making it explicit that there is no
inverse.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In ipa_modem_stop(), if the modem netdev pointer is non-null we call
ipa_stop(). We check for an error and if one is returned we handle
it. But ipa_stop() never returns an error, so this extra handling
is unnecessary. Simplify the code in ipa_modem_stop() based on the
knowledge no error handling is needed at this spot.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In ipa_modem_start(), we set endpoint netdev pointers before the
network device is registered. If registration fails, we don't undo
those assignments. Instead, wait to assign the netdev pointer until
after registration succeeds.
Set these endpoint netdev pointers to NULL in ipa_modem_stop()
before unregistering the network device.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On IPA v3.5.1, the sequencer type for the modem TX endpoint does not
define the replication portion in the same way the downstream code
does. This difference doesn't affect the behavior of the upstream
code, but I'd prefer the two code bases use the same configuration
value here.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
I no longer know why a validation check ensured the size of an entry
passed to gsi_trans_pool_init() was restricted to be a multiple of 8.
For 32-bit builds, this condition doesn't always hold, and for DMA
pools, the size is rounded up to a power of 2 anyway.
Remove this restriction.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove repeated words "that" and "the".
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Acked-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Entries in an IPA route or filter table are 64-bit little-endian
addresses, each of which refers to a routing or filtering rule.
The format of these table slots are fixed, but IPA_TABLE_ENTRY_SIZE
is used to define their size. This symbol doesn't really add value,
and I think it unnecessarily obscures what a table entry *is*.
So get rid of IPA_TABLE_ENTRY_SIZE, and just use sizeof(__le64) in
its place throughout the code.
Update the comments in "ipa_table.c" to provide a little better
explanation of these table slots.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent patch avoided doing 64-bit modulo operations by checking
the alignment of some DMA allocations using only the lower 32 bits
of the address.
David Laight pointed out (after the fix was committed) that DMA
allocations might already satisfy the alignment requirements. And
he was right.
Remove the alignment checks that occur after DMA allocation requests,
and update comments to explain why the constraint is satisfied. The
only place IPA_TABLE_ALIGN was used was to check the alignment; it is
therefore no longer needed, so get rid of it.
Add comments where GSI_RING_ELEMENT_SIZE and the tre_count and
event_count channel data fields are defined to make explicit they
are required to be powers of 2.
Revise a comment in gsi_trans_pool_init_dma(), taking into account
that dma_alloc_coherent() guarantees its result is aligned to a page
size (or order thereof).
Don't bother printing an error if a DMA allocation fails.
Suggested-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the SC7180 configuration data file so that its name is
derived from its IPA version.
Update a few other references to the code that talk about the SC7180
rather than just IPA v4.2.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the SDM845 configuration data file so that its name is
derived from its IPA version. I am not aware of any special IPA
behavior or handling that would be based on a specific SoC (as
opposed to a specific version of the IPA it contains).
Update a few other references to the code that talk about the SDM845
rather than just IPA v3.5.1.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't typically need much information about modem endpoints.
Normally we need to specify information about modem endpoints in
configuration data in only two cases:
- When a modem TX endpoint supports filtering
- When another endpoint's configuration refers to it
For the first case, the AP initializes the filter table, and must
know how many endpoints (AP and modem) support filtering. An
example of the second case is the AP->modem TX endpoint, which
defines the modem<-AP RX endpoint as its status endpoint.
There is one exception to this, and it's due to a hardware quirk.
For IPA v4.2 (only) there is a problem related to allocating GSI
channels. And to work around this, the AP allocates *all* GSI
channels at startup time--including those used by the modem.
Get rid of the configuration information for two endpoints not
required for the SDM845. SC7180 runs IPA v4.2, so we can't
eliminate any modem endpoint definitions there.
Two more minor changes:
- Reorder the members defined for the ipa_endpoint_name enumerated
type to match the order used in configuration data files when
defining endpoints.
- Add a new name, IPA_ENDPOINT_MODEM_DL_NLO_TX, which can be used
for IPA v4.5+.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The backward compatibility register value is a platform-specific
property that is not stored in the platform data. Create a data
field where this can be represented, and get rid ipa_reg_bcr_val().
This register is not present starting with IPA v4.5.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix all warnings produced when running:
scripts/kernel-doc -none drivers/net/ipa/*.[ch]
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPA versions 3.0 and 3.1 support up to 8 resource groups. There is
some interest in supporting these older versions of the hardware, so
update the resource configuration code to program resource limits
for these groups if specified.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The arrays of source and destination resource limits defined in
configuration data are of a fixed size--which is the maximum number
of resource groups supported for any platform. Most platforms will
use fewer than that many groups.
Add new members to the ipa_rsrc_group_id enumerated type to define
the number of source and destination resource groups are defined for
the platform. (This type is defined for each platform in its data
file.)
Add a new field to the resource configuration data that indicates
how many of the source and destination resource groups are actually
used for the platform, and initialize it with the count value. This
allows us to determine the number of groups defined for the platform
without exposing the ipa_rsrc_group_id enumerated type.
As a result, we no longer need ipa_resource_group_src_count()
and ipa_resource_group_dst_count(), because each platform now
defines its supported number of resource groups. So get rid of
those two functions.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the resource data pointer to ipa_resource_config_src() and
ipa_resource_config_dst() to be used for configuring resource
limits.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ipa_resource_src and ipa_resource_dst structures are identical
in form, so just replace them with a single structure.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace IPA_RESOURCE_GROUP_SRC_MAX and IPA_RESOURCE_GROUP_DST_MAX
with a single symbol, IPA_RESOURCE_GROUP_MAX.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most platforms have the same set of source and destination resource
types. But some older platforms have some additional ones, and it's
possible different resources will be used in the future.
Move the definition of the ipa_resource_type enumerated type so it
is defined for each platform in its configuration data file. This
permits each to have a distinct set of resources.
Shorten the data files slightly, by putting the min and max limit
values on the same line.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the type field from the ipa_resource_src and ipa_resource_dst
structures, and instead use that value as the index into the arrays
of source and destination resources.
Change ipa_resource_config_src() and ipa_resource_config_dst() so
the resource type is passed in as an argument.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Combine the ipa_resource_type_src and ipa_resource_type_dst
enumerated types into a single enumerated type, ipa_resource_type.
Assign value 0 to the first element for the source and destination
types, so their numeric values are preserved. Add some additional
commentary where these are defined, stating explicitly that code
assumes the first source and first destination member must have
numeric value 0.
Fix the kerneldoc comments for the ipa_gsi_endpoint_data structure.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the SDM845 configuration data defines resource limits for
the first two resource groups (for both source and destination
resource types). The hardware supports additional resource groups,
and we should program the resource limits for those groups as well.
Even the "unused" destination resource group (number 2) should have
non-zero limits programmed in some cases, to ensure correct operation.
Add these missing resource group limit definitions to the SDM845
configuration data.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define a new ipa_resource_group_id enumerated type, whose members
have numeric values that match the resource group number used when
programming the hardware. Each platform supports a different number
of source and destination resource groups, so define the type
separately for each platform in its configuration data file.
Use these new symbolic values when specifying the resource group an
endpoint is associated with. And use them to index the limits
arrays for source and destination resources, making it clearer how
these values are used.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the number of resource groups supported by the hardware is less
than a certain number, we return early in ipa_resource_config_src()
and ipa_resource_config_dst() (to avoid programming resource limits
for non-existent groups).
Unfortunately, these checks are off by one. Fix this problem in the
four places it occurs.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate the IPA resource-related code into a new source file,
"ipa_resource.c", and matching header file "ipa_resource.h".
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPA v4.5 (GSI v2.5) supports a larger set of channel protocols, and
adds an additional field to hold the most-significant bits of the
protocol identifier on a channel.
Add an inline function that encodes the protocol (including the
extra bits for newer versions of IPA), and define some additional
protocols. At this point we still use only GPI protocol.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each GSI channel has a CNTXT_1 register that encodes the size of its
ring buffer. The size of the field that records that is increased
starting at IPA v4.9. Replace the use of a fixed-size field mask
with a new inline function that encodes that size value.
Similarly, the size of GSI event rings can be larger starting with
IPA v4.9, so create a function to encode that as well.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The main purpose of this is to extend these GSI register definitions
to support additional IPA versions.
This patch makes some minor updates to "gsi_reg.h":
- Define a DB_IN_BYTES field in the channel QOS register
- Add some comments clarifying when certain fields are valid
- Add the definition of GSI_CH_DB_STOP channel command
- Add a couple of blank lines
- Move one comment and indent another
- Delete two unused register definitions at the end.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with IPA v4.7, registers related to IPA interrupts are
located at a fixed offset 0x1000 above than the addresses used for
earlier versions. Define and use functions to provide the offset to
use for these registers based on IPA version.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPA version 4.9 and later use a different layout of some fields
found in the COMP_CFG register.
Define arbitration_lock_disable_encoded(), and use it to encode a
value into the ATOMIC_FETCHER_ARB_LOCK_DIS field based on the IPA
version.
And define full_flush_rsc_closure_en_encoded() to encode a value
into the FULL_FLUSH_WAIT_RSC_CLOSE_EN field based on the IPA
version.
The values of these fields are neither modified nor extracted by
current code, but this patch makes this possible for all supported
versions.
Fix a mistaken comment above ipa_hardware_config_comp() intended to
describe the purpose for the register.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add and update IPA register definitions. Extend these definitions
to incorporate a fairly small number of new symbols (register
offsets and fields) to support IPA v3.0, v3.1, v3.5, v4.0, v4.1,
v4.7, 4.9, and v4.11, and have the comments reflect when they are
valid. None of the added symbols require changes elsewhere in the
code.
Update rsrc_grp_encoded() to support these other IPA versions.
Add kerneldoc comments for the IPA IRQ numbers and sequencer type.
Fix a few spots where the version check should be less restrictive
(missed by an earlier patch).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increase the maximum number of channels and event rings supported by
the driver, to allow the maximum available on the SDX55.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only use ipa_aggr_granularity_val() inside "ipa_main.c", so it
doesn't really need to be defined in a header file. It makes some
sense to be grouped with the register definitions, but it is unlike
the other inline functions now defined in "ipa_reg.h". So move it
into "ipa_main.c" where it's used. TIMER_FREQUENCY is used only
by that function, so move that definition as well.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all of the bits of the LOCAL_PKT_PROC_CNTXT register are valid.
Until IPA v4.5, there are 17 valid bits (though the bottom three
must be zero). Starting with IPA v4.5, 18 bits are valid.
Introduce proc_cntxt_base_addr_encoded() to encode the base address
for use in the register using only the valid bits.
Shorten the name of the register (omit "_BASE") to avoid the need to
wrap the line in the one place it's used.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define the ENDP_INIT_NAT register for setting up the NAT
configuration for an endpoint. We aren't using NAT at this
time, so explicitly set the type to BYPASS for all endpoints.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IPA version definitions for all IPA v3.x and v4.x. Fix the GSI
version associated with IPA version 4.1.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify conditional tests throughout the IPA code so they do not
assume that IPA v3.5.1 is the oldest version supported. Also remove
assumptions that IPA v4.5 is the newest version of IPA supported.
Augment versions in comments with "+", to be clearer that the
comment applies to a version and subsequent versions. (E.g.,
"present for IPA v4.2+" instead of just "present for v4.2".)
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for a 32 bit x86 build to use a 64 bit DMA address.
There are two remaining spots where the IPA driver does a modulo
operation to check alignment of a DMA address, and under certain
conditions this can lead to a build error on i386 (at least).
The alignment checks we're doing are for power-of-2 values, and this
means the lower 32 bits of the DMA address can be used. This ensures
both operands to the modulo operator are 32 bits wide.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: David S. Miller <davem@davemloft.net>
We only program the sequencer type for TX endpoints. So move the
definition of the sequencer type fields into the TX-specific portion
of the endpoint configuration data. There's no need to maintain
this in the IPA structure; we can extract it from the configuration
data it points to in the one spot it's needed.
We previously specified the sequencer type for RX endpoints with
INVALID values. These are no longer needed, so get rid of them.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
An IPA endpoint has a sequencer that must be configured based on how
the endpoint is to be used. Currently the IPA code programs the
sequencer type by splitting a value into four 4-bit nibbles. Doing
that doesn't really add much value, and regardless, a better way of
splitting the sequencer type is into two halves--the lower byte
describing how normal packet processing is handled, and the next
byte describing information about processing replicas.
So split the sequencer type into two sub-parts: the sequencer type
and the replication sequencer type. Define the values supported for
the "main" sequencer type, and define the values supported for the
replication part separately.
In addition, the sequencer type names are quite verbose, encoding
what the type includes, but also what it *excludes*. Rename the
sequencer types in a way that mainly describes the number of passes
that a packet takes through the IPA processing pipeline, and how
many of those passes end by supplying the processed packet to the
microprocessor.
The result expands the supported types beyond what is required for
now, but simplifies the way these are defined.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
