The PSSCR value is not stored to PACA_REQ_PSSCR if the CPU does not
have the XER[SO] bug.
Fix this by storing up-front, outside the workaround code. The initial
test is not required because it is a slow path.
The workaround is made to depend on CONFIG_KVM_BOOK3S_HV_POSSIBLE, to
match pnv_power9_force_smt4_catch() where it is used. Drop the comment
on pnv_power9_force_smt4_catch() as it's no longer true.
Fixes: 7672691a08 ("powerpc/powernv: Provide a way to force a core into SMT4 mode")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
After migration the security feature flags might have changed (e.g.,
destination system with unpatched firmware), but some flags are not
set/clear again in init_cpu_char_feature_flags() because it assumes
the security flags to be the defaults.
Additionally, if the H_GET_CPU_CHARACTERISTICS hypercall fails then
init_cpu_char_feature_flags() does not run again, which potentially
might leave the system in an insecure or sub-optimal configuration.
So, just restore the security feature flags to the defaults assumed
by init_cpu_char_feature_flags() so it can set/clear them correctly,
and to ensure safe settings are in place in case the hypercall fail.
Fixes: f636c14790 ("powerpc/pseries: Set or clear security feature flags")
Depends-on: 19887d6a28e2 ("powerpc: Move default security feature flags")
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This moves the definition of the default security feature flags
(i.e., enabled by default) closer to the security feature flags.
This can be used to restore current flags to the default flags.
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
flush_thread() calls __set_breakpoint() via set_debug_reg_defaults()
without checking ppc_breakpoint_available(). On Power8 or later CPUs
which have the DAWR feature disabled that will cause a write to the
DABR which is incorrect as those CPUs don't have a DABR.
Fix it two ways, by checking ppc_breakpoint_available() in
set_debug_reg_defaults(), and also by reworking __set_breakpoint() to
only write to DABR on Power7 or earlier.
Fixes: 9654153158 ("powerpc: Disable DAWR in the base POWER9 CPU features")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Rework the logic in __set_breakpoint()]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
arch/powerpc/kvm/book3s_hv.c: In function ‘kvmppc_h_set_mode’:
arch/powerpc/kvm/book3s_hv.c:745:8: error: implicit declaration of function ‘ppc_breakpoint_available’
if (!ppc_breakpoint_available())
^~~~~~~~~~~~~~~~~~~~~~~~
Fixes: 398e712c00 ("KVM: PPC: Book3S HV: Return error from h_set_mode(SET_DAWR) on POWER9")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 8e0b634b13 ("powerpc/64s: Do not allocate lppaca if we are
not virtualized") removed allocation of lppaca on bare metal
platforms. But with CONFIG_PPC_SPLPAR enabled, we still access the
lppaca on bare metal in some code paths.
Fix this but adding runtime checks for SPLPAR (shared processor LPAR).
Fixes: 8e0b634b13 ("powerpc/64s: Do not allocate lppaca if we are not virtualized")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull removal of in-kernel calls to syscalls from Dominik Brodowski:
"System calls are interaction points between userspace and the kernel.
Therefore, system call functions such as sys_xyzzy() or
compat_sys_xyzzy() should only be called from userspace via the
syscall table, but not from elsewhere in the kernel.
At least on 64-bit x86, it will likely be a hard requirement from
v4.17 onwards to not call system call functions in the kernel: It is
better to use use a different calling convention for system calls
there, where struct pt_regs is decoded on-the-fly in a syscall wrapper
which then hands processing over to the actual syscall function. This
means that only those parameters which are actually needed for a
specific syscall are passed on during syscall entry, instead of
filling in six CPU registers with random user space content all the
time (which may cause serious trouble down the call chain). Those
x86-specific patches will be pushed through the x86 tree in the near
future.
Moreover, rules on how data may be accessed may differ between kernel
data and user data. This is another reason why calling sys_xyzzy() is
generally a bad idea, and -- at most -- acceptable in arch-specific
code.
This patchset removes all in-kernel calls to syscall functions in the
kernel with the exception of arch/. On top of this, it cleans up the
three places where many syscalls are referenced or prototyped, namely
kernel/sys_ni.c, include/linux/syscalls.h and include/linux/compat.h"
* 'syscalls-next' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/linux: (109 commits)
bpf: whitelist all syscalls for error injection
kernel/sys_ni: remove {sys_,sys_compat} from cond_syscall definitions
kernel/sys_ni: sort cond_syscall() entries
syscalls/x86: auto-create compat_sys_*() prototypes
syscalls: sort syscall prototypes in include/linux/compat.h
net: remove compat_sys_*() prototypes from net/compat.h
syscalls: sort syscall prototypes in include/linux/syscalls.h
kexec: move sys_kexec_load() prototype to syscalls.h
x86/sigreturn: use SYSCALL_DEFINE0
x86: fix sys_sigreturn() return type to be long, not unsigned long
x86/ioport: add ksys_ioperm() helper; remove in-kernel calls to sys_ioperm()
mm: add ksys_readahead() helper; remove in-kernel calls to sys_readahead()
mm: add ksys_mmap_pgoff() helper; remove in-kernel calls to sys_mmap_pgoff()
mm: add ksys_fadvise64_64() helper; remove in-kernel call to sys_fadvise64_64()
fs: add ksys_fallocate() wrapper; remove in-kernel calls to sys_fallocate()
fs: add ksys_p{read,write}64() helpers; remove in-kernel calls to syscalls
fs: add ksys_truncate() wrapper; remove in-kernel calls to sys_truncate()
fs: add ksys_sync_file_range helper(); remove in-kernel calls to syscall
kernel: add ksys_setsid() helper; remove in-kernel call to sys_setsid()
kernel: add ksys_unshare() helper; remove in-kernel calls to sys_unshare()
...
Pull x86 dma mapping updates from Ingo Molnar:
"This tree, by Christoph Hellwig, switches over the x86 architecture to
the generic dma-direct and swiotlb code, and also unifies more of the
dma-direct code between architectures. The now unused x86-only
primitives are removed"
* 'x86-dma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
dma-mapping: Don't clear GFP_ZERO in dma_alloc_attrs
swiotlb: Make swiotlb_{alloc,free}_buffer depend on CONFIG_DMA_DIRECT_OPS
dma/swiotlb: Remove swiotlb_{alloc,free}_coherent()
dma/direct: Handle force decryption for DMA coherent buffers in common code
dma/direct: Handle the memory encryption bit in common code
dma/swiotlb: Remove swiotlb_set_mem_attributes()
set_memory.h: Provide set_memory_{en,de}crypted() stubs
x86/dma: Remove dma_alloc_coherent_gfp_flags()
iommu/intel-iommu: Enable CONFIG_DMA_DIRECT_OPS=y and clean up intel_{alloc,free}_coherent()
iommu/amd_iommu: Use CONFIG_DMA_DIRECT_OPS=y and dma_direct_{alloc,free}()
x86/dma/amd_gart: Use dma_direct_{alloc,free}()
x86/dma/amd_gart: Look at dev->coherent_dma_mask instead of GFP_DMA
x86/dma: Use generic swiotlb_ops
x86/dma: Use DMA-direct (CONFIG_DMA_DIRECT_OPS=y)
x86/dma: Remove dma_alloc_coherent_mask()
Using this helper allows us to avoid the in-kernel calls to the
sys_readahead() syscall. The ksys_ prefix denotes that this function is
meant as a drop-in replacement for the syscall. In particular, it uses the
same calling convention as sys_readahead().
This patch is part of a series which removes in-kernel calls to syscalls.
On this basis, the syscall entry path can be streamlined. For details, see
http://lkml.kernel.org/r/20180325162527.GA17492@light.dominikbrodowski.net
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-mm@kvack.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Using this helper allows us to avoid the in-kernel calls to the
sys_mmap_pgoff() syscall. The ksys_ prefix denotes that this function is
meant as a drop-in replacement for the syscall. In particular, it uses the
same calling convention as sys_mmap_pgoff().
This patch is part of a series which removes in-kernel calls to syscalls.
On this basis, the syscall entry path can be streamlined. For details, see
http://lkml.kernel.org/r/20180325162527.GA17492@light.dominikbrodowski.net
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-mm@kvack.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Using the ksys_fadvise64_64() helper allows us to avoid the in-kernel
calls to the sys_fadvise64_64() syscall. The ksys_ prefix denotes that
this function is meant as a drop-in replacement for the syscall. In
particular, it uses the same calling convention as ksys_fadvise64_64().
Some compat stubs called sys_fadvise64(), which then just passed through
the arguments to sys_fadvise64_64(). Get rid of this indirection, and call
ksys_fadvise64_64() directly.
This patch is part of a series which removes in-kernel calls to syscalls.
On this basis, the syscall entry path can be streamlined. For details, see
http://lkml.kernel.org/r/20180325162527.GA17492@light.dominikbrodowski.net
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-mm@kvack.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Using the ksys_fallocate() wrapper allows us to get rid of in-kernel
calls to the sys_fallocate() syscall. The ksys_ prefix denotes that this
function is meant as a drop-in replacement for the syscall. In
particular, it uses the same calling convention as sys_fallocate().
This patch is part of a series which removes in-kernel calls to syscalls.
On this basis, the syscall entry path can be streamlined. For details, see
http://lkml.kernel.org/r/20180325162527.GA17492@light.dominikbrodowski.net
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Using the ksys_p{read,write}64() wrappers allows us to get rid of
in-kernel calls to the sys_pread64() and sys_pwrite64() syscalls.
The ksys_ prefix denotes that this function is meant as a drop-in
replacement for the syscall. In particular, it uses the same calling
convention as sys_p{read,write}64().
This patch is part of a series which removes in-kernel calls to syscalls.
On this basis, the syscall entry path can be streamlined. For details, see
http://lkml.kernel.org/r/20180325162527.GA17492@light.dominikbrodowski.net
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Using the ksys_truncate() wrapper allows us to get rid of in-kernel
calls to the sys_truncate() syscall. The ksys_ prefix denotes that this
function is meant as a drop-in replacement for the syscall. In
particular, it uses the same calling convention as sys_truncate().
This patch is part of a series which removes in-kernel calls to syscalls.
On this basis, the syscall entry path can be streamlined. For details, see
http://lkml.kernel.org/r/20180325162527.GA17492@light.dominikbrodowski.net
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Using this helper allows us to avoid the in-kernel calls to the
sys_sync_file_range() syscall. The ksys_ prefix denotes that this function
is meant as a drop-in replacement for the syscall. In particular, it uses
the same calling convention as sys_sync_file_range().
This patch is part of a series which removes in-kernel calls to syscalls.
On this basis, the syscall entry path can be streamlined. For details, see
http://lkml.kernel.org/r/20180325162527.GA17492@light.dominikbrodowski.net
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Using the ksys_ftruncate() wrapper allows us to get rid of in-kernel
calls to the sys_ftruncate() syscall. The ksys_ prefix denotes that this
function is meant as a drop-in replacement for the syscall. In
particular, it uses the same calling convention as sys_ftruncate().
This patch is part of a series which removes in-kernel calls to syscalls.
On this basis, the syscall entry path can be streamlined. For details, see
http://lkml.kernel.org/r/20180325162527.GA17492@light.dominikbrodowski.net
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Pull perf updates from Ingo Molnar:
"The main kernel side changes were:
- Modernize the kprobe and uprobe creation/destruction tooling ABIs:
The existing text based APIs (kprobe_events and uprobe_events in
tracefs), are naive, limited ABIs in that they require user-space
to clean up after themselves, which is both difficult and fragile
if the tool is buggy or exits unexpectedly. In other words they are
not really suited for modern, robust tooling.
So introduce a modern, file descriptor based ABI that does not have
these limitations: introduce the 'perf_kprobe' and 'perf_uprobe'
PMUs and extend the perf_event_open() syscall to create events with
a kprobe/uprobe attached to them. These [k,u]probe are associated
with this file descriptor, so they are not available in tracefs.
(Song Liu)
- Intel Cannon Lake CPU support (Harry Pan)
- Intel PT cleanups (Alexander Shishkin)
- Improve the performance of pinned/flexible event groups by using RB
trees (Alexey Budankov)
- Add PERF_EVENT_IOC_MODIFY_ATTRIBUTES which allows the modification
of hardware breakpoints, which new ABI variant massively speeds up
existing tooling that uses hardware breakpoints to instrument (and
debug) memory usage.
(Milind Chabbi, Jiri Olsa)
- Various Intel PEBS handling fixes and improvements, and other Intel
PMU improvements (Kan Liang)
- Various perf core improvements and optimizations (Peter Zijlstra)
- ... misc cleanups, fixes and updates.
There's over 200 tooling commits, here's an (imperfect) list of
highlights:
- 'perf annotate' improvements:
* Recognize and handle jumps to other functions as calls, which
improves the navigation along jumps and back. (Arnaldo Carvalho
de Melo)
* Add the 'P' hotkey in TUI annotation to dump annotation output
into a file, to ease e-mail reporting of annotation details.
(Arnaldo Carvalho de Melo)
* Add an IPC/cycles column to the TUI (Jin Yao)
* Improve s390 assembly annotation (Thomas Richter)
* Refactor the output formatting logic to better separate it into
interactive and non-interactive features and add the --stdio2
output variant to demonstrate this. (Arnaldo Carvalho de Melo)
- 'perf script' improvements:
* Add Python 3 support (Jaroslav Škarvada)
* Add --show-round-event (Jiri Olsa)
- 'perf c2c' improvements:
* Add NUMA analysis support (Jiri Olsa)
- 'perf trace' improvements:
* Improve PowerPC support (Ravi Bangoria)
- 'perf inject' improvements:
* Integrate ARM CoreSight traces (Robert Walker)
- 'perf stat' improvements:
* Add the --interval-count option (yuzhoujian)
* Add the --timeout option (yuzhoujian)
- 'perf sched' improvements (Changbin Du)
- Vendor events improvements :
* Add IBM s390 vendor events (Thomas Richter)
* Add and improve arm64 vendor events (John Garry, Ganapatrao
Kulkarni)
* Update POWER9 vendor events (Sukadev Bhattiprolu)
- Intel PT tooling improvements (Adrian Hunter)
- PMU handling improvements (Agustin Vega-Frias)
- Record machine topology in perf.data (Jiri Olsa)
- Various overwrite related cleanups (Kan Liang)
- Add arm64 dwarf post unwind support (Kim Phillips, Jean Pihet)
- ... and lots of other changes, cleanups and fixes, see the shortlog
and Git history for details"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (262 commits)
perf/x86/intel: Enable C-state residency events for Cannon Lake
perf/x86/intel: Add Cannon Lake support for RAPL profiling
perf/x86/pt, coresight: Clean up address filter structure
perf vendor events s390: Add JSON files for IBM z14
perf vendor events s390: Add JSON files for IBM z13
perf vendor events s390: Add JSON files for IBM zEC12 zBC12
perf vendor events s390: Add JSON files for IBM z196
perf vendor events s390: Add JSON files for IBM z10EC z10BC
perf mmap: Be consistent when checking for an unmaped ring buffer
perf mmap: Fix accessing unmapped mmap in perf_mmap__read_done()
perf build: Fix check-headers.sh opts assignment
perf/x86: Update rdpmc_always_available static key to the modern API
perf annotate: Use absolute addresses to calculate jump target offsets
perf annotate: Defer searching for comma in raw line till it is needed
perf annotate: Support jumping from one function to another
perf annotate: Add "_local" to jump/offset validation routines
perf python: Reference Py_None before returning it
perf annotate: Mark jumps to outher functions with the call arrow
perf annotate: Pass function descriptor to its instruction parsing routines
perf annotate: No need to calculate notes->start twice
...
In commit 9690c15742 ("powerpc/mm/radix: Fix always false comparison
against MMU_NO_CONTEXT") an issue was discovered where `mm->context.id` was
being truncated to an `unsigned int`, while the PID is actually an
`unsigned long`. Update the earlier patch by fixing one remaining
occurrence. Discovered during a compilation with W=1:
arch/powerpc/mm/tlb-radix.c:702:19: error: comparison is always false due to limited range of data type [-Werror=type-limits]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When using SIG_DBG_BRANCH_TRACING, MSR.BE is left enabled in the
user context when single_step_exception() prepares the SIGTRAP
delivery. The resulting branch-trap-within-the-SIGTRAP-handler
isn't healthy.
Commit 2538c2d08f broke this, by
replacing an MSR mask operation of ~(MSR_SE | MSR_BE) with a call
to clear_single_step() which only clears MSR_SE.
This patch adds a new helper, clear_br_trace(), which clears the
debug trap before invoking the signal handler. This helper is a
NOP for BookE as SIG_DBG_BRANCH_TRACING isn't supported on BookE.
Signed-off-by: Matt Evans <matt@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This reduces vmlinux text size by 1kB and data by 1.5kB with a small
build!
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Add the recently added CPU_FTRS_POWER9_DD2_2 to the little
endian possible mask as noticed by Nick.]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add GENERIC_CPU support for little-endian rather than using POWER8
specific selection for POWER9 and above.
Restrict GENERIC_CPU to POWER8 and above on little endian.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Duplicate GENERIC_CPU to avoid a kbuild warning about the prompt
being redefined. Spell out that GENERIC means >= POWER4 for BE.]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
POWER4 has been broken since at least the change 49d09bf2a6
("powerpc/64s: Optimise MSR handling in exception handling"), which
requires mtmsrd L=1 support. This was introduced in ISA v2.01, and
POWER4 supports ISA v2.00.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The last usage was removed in c17b98cf60 ("KVM: PPC: Book3S HV:
Remove code for PPC970 processors") (Dec 2014).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The CPU_FTR_POWER9_DD2_1 flag is intended to be set for DD2.1 and
above (which is what the cputable setup does). Fix DT CPU features
quirk setup to match.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Merge with upstream changes]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Rather than override the machine type in .S code (which can hide wrong
or ambiguous code generation for the target), set the type to power4
for all assembly.
This also means we need to be careful not to build power4-only code
when we're not building for Book3S, such as the "power7" versions of
copyuser/page/memcpy.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Fix Book3E build, don't build the "power7" variants for non-Book3S]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
ALTIVEC and VSX features are not added by to default to the POWERx CPU
feature sets because they are intended to be enabled by firmware.
Currently they end up in CPU_FTRS_POSSIBLE due to their inclusion in
other the set for other CPUs, eg. PPC970.
But they should be added individually to the CPU_FTRS_POSSIBLE set,
because if we reduce the set of CPUs that are built-for they may
disappear from the possible mask.
It already contains CPU_FTR_VSX, so add ALTIVEC. The _COMP features
should be used because they won't be present if compiled out.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Add detail to change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
It's not a bug to have features missing in CPU_FTR_ALWAYS, but it is a
missed opportunity for optimisation.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When building a uImage or zImage using ppc6xx_defconfig and some other
defconfigs, the following error occurs with GCC 4.5.1:
/arch/powerpc/boot/libfdt_env.h:10:13: error: redefinition of typedef 'uint32_t'
/arch/powerpc/boot/types.h:21:13: note: previous declaration of 'uint32_t' was here
/arch/powerpc/boot/libfdt_env.h:11:13: error: redefinition of typedef 'uint64_t'
/arch/powerpc/boot/types.h:22:13: note: previous declaration of 'uint64_t' was here
The problem is that commit 656ad58ef1 (powerpc/boot: Add OPAL
console to epapr wrappers) adds typedefs for uint32_t and uint64_t to
type.h but doesn't remove the pre-existing (and now duplicate)
typedefs from libfdt_env.h.
Fix the error by removing the duplicate typedefs from libfdt_env.h
Signed-off-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When waking from a CPU idle instruction (e.g., nap or stop), the sync
for ordering the KVM secondary thread state can be avoided if there
wakeup is coming from a kernel context rather than KVM context.
This improves performance for ping-pong benchmark with the stop0 idle
state by 0.46% for 2 threads in the same core, and 1.02% for different
cores.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Implement a new function to invoke stop, power9_offline_stop, which is
like power9_idle_stop but used by the cpu hotplug code.
Move KVM secondary state manipulation code to the offline case.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
system_reset_exception does most of its own crash handling now,
invoking the debugger or crash dumps if they are registered. If not,
then it goes through to die() to print stack traces, and then is
supposed to panic (according to comments).
However after die() prints oopses, it does its own handling which
doesn't allow system_reset_exception to panic (e.g., it may just
kill the current process). This patch causes sreset exceptions to
return from die after it prints messages but before acting.
This also stops die from invoking the debugger on 0x100 crashes.
system_reset_exception similarly calls the debugger. It had been
thought this was harmless (because if the debugger was disabled,
neither call would fire, and if it was enabled the first call
would return). However in some cases like xmon 'X' command, the
debugger returns 0, which currently causes it to be entered
again (first in system_reset_exception, then in die), which is
confusing.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
System Reset, being an NMI, must return more carefully than other
interrupts. It has traditionally returned via the nromal return
from exception path, but that has a number of problems.
- r13 does not get restored if returning to kernel. This is for
interrupts which may cause a context switch, which sreset will
never do. Interrupting OPAL (which uses a different r13) is one
place where this causes breakage.
- It may cause several other problems returning to kernel with
preempt or TIF_EMULATE_STACK_STORE if it hits at the wrong time.
It's safer just to have a simple restore and return, like machine
check which is the other NMI.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The current EEH callbacks can race with a driver unbind. This can
result in a backtraces like this:
EEH: Frozen PHB#0-PE#1fc detected
EEH: PE location: S000009, PHB location: N/A
CPU: 2 PID: 2312 Comm: kworker/u258:3 Not tainted 4.15.6-openpower1 #2
Workqueue: nvme-wq nvme_reset_work [nvme]
Call Trace:
dump_stack+0x9c/0xd0 (unreliable)
eeh_dev_check_failure+0x420/0x470
eeh_check_failure+0xa0/0xa4
nvme_reset_work+0x138/0x1414 [nvme]
process_one_work+0x1ec/0x328
worker_thread+0x2e4/0x3a8
kthread+0x14c/0x154
ret_from_kernel_thread+0x5c/0xc8
nvme nvme1: Removing after probe failure status: -19
<snip>
cpu 0x23: Vector: 300 (Data Access) at [c000000ff50f3800]
pc: c0080000089a0eb0: nvme_error_detected+0x4c/0x90 [nvme]
lr: c000000000026564: eeh_report_error+0xe0/0x110
sp: c000000ff50f3a80
msr: 9000000000009033
dar: 400
dsisr: 40000000
current = 0xc000000ff507c000
paca = 0xc00000000fdc9d80 softe: 0 irq_happened: 0x01
pid = 782, comm = eehd
Linux version 4.15.6-openpower1 (smc@smc-desktop) (gcc version 6.4.0 (Buildroot 2017.11.2-00008-g4b6188e)) #2 SM P Tue Feb 27 12:33:27 PST 2018
enter ? for help
eeh_report_error+0xe0/0x110
eeh_pe_dev_traverse+0xc0/0xdc
eeh_handle_normal_event+0x184/0x4c4
eeh_handle_event+0x30/0x288
eeh_event_handler+0x124/0x170
kthread+0x14c/0x154
ret_from_kernel_thread+0x5c/0xc8
The first part is an EEH (on boot), the second half is the resulting
crash. nvme probe starts the nvme_reset_work() worker thread. This
worker thread starts touching the device which see a device error
(EEH) and hence queues up an event in the powerpc EEH worker
thread. nvme_reset_work() then continues and runs
nvme_remove_dead_ctrl_work() which results in unbinding the driver
from the device and hence releases all resources. At the same time,
the EEH worker thread starts doing the EEH .error_detected() driver
callback, which no longer works since the resources have been freed.
This fixes the problem in the same way the generic PCIe AER code (in
drivers/pci/pcie/aer/aerdrv_core.c) does. It makes the EEH code hold
the device_lock() while performing the driver EEH callbacks and
associated code. This ensures either the callbacks are no longer
register, or if they are registered the driver will not be removed
from underneath us.
This has been broken forever. The EEH call backs were first introduced
in 2005 (in 77bd741561) but it's not clear if a lock was needed back
then.
Fixes: 77bd741561 ("[PATCH] powerpc: PCI Error Recovery: PPC64 core recovery routines")
Cc: stable@vger.kernel.org # v2.6.16+
Signed-off-by: Michael Neuling <mikey@neuling.org>
Reviewed-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
kexec_file_load() on powerpc doesn't support kdump kernels yet, so it
returns -ENOTSUPP in that case.
I've recently learned that this errno is internal to the kernel and
isn't supposed to be exposed to userspace. Therefore, change to
-EOPNOTSUPP which is defined in an uapi header.
This does indeed make kexec-tools happier. Before the patch, on
ppc64le:
# ~bauermann/src/kexec-tools/build/sbin/kexec -s -p /boot/vmlinuz
kexec_file_load failed: Unknown error 524
After the patch:
# ~bauermann/src/kexec-tools/build/sbin/kexec -s -p /boot/vmlinuz
kexec_file_load failed: Operation not supported
Fixes: a0458284f0 ("powerpc: Add support code for kexec_file_load()")
Cc: stable@vger.kernel.org # v4.10+
Reported-by: Dave Young <dyoung@redhat.com>
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Reviewed-by: Simon Horman <horms@verge.net.au>
Reviewed-by: Dave Young <dyoung@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This hack, introduced in commit c5df7f7751 ("powerpc: allow ioremap
within reserved memory regions") is now unnecessary.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Because the two memory blocks (usually called MEM1 and MEM2) are not
merged anymore, __request_region in kernel/resource.c will correctly
allow reserving regions in the physical address space between MEM1 and
MEM2, where many important peripherals are (GPIO, MMC, USB, ...).
A previous change to __ioremap_caller in arch/powerpc/mm/pgtable_32.c
ensures that multiple memblocks are properly considered in ioremap; this
makes it unnecessary to set __allow_ioremap_reserved.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On systems where there is MMIO space between different blocks of RAM in
the physical address space, __ioremap_caller did not allow mapping these
MMIO areas, because they were below the end RAM and thus considered RAM
as well. Use the memblock-based page_is_ram function, which returns
false for such MMIO holes.
v2:
Keep the check for p < virt_to_phys(high_memory). On 32-bit systems
with high memory (memory above physical address 4GiB), the high memory
is expected to be available though ioremap. The high_memory variable
marks the end of low memory; comparing against it means that only
ioremap requests for low RAM will be denied.
Reported by Michael Ellerman.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
To support accurate checking for different blocks of memory on PPC32,
use the same memblock-based approach that's already used on PPC64 also
on PPC32.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Instead of open-coding the search in page_is_ram, call memblock_is_memory.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The Wii has a blue LED in the disk drive slot, which is controlled via a
GPIO line. Add this LED to wii.dts, and mark it as a panic-indicator.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
These are the GPIO line names on a Nintendo Wii, as documented in:
https://wiibrew.org/wiki/Hardware/Hollywood_GPIOs
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The Hollywood GPIO controller supports 32 GPIOs, but on the Wii, only 24
are used.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The Hollywood chipset's GPIO controller has two sets of registers: One
for access by the PowerPC CPU, and one for access by the ARM coprocessor
(but both are accessible from the PPC because the memory firewall
(AHBPROT) is usually disabled when booting Linux, today).
The wii_power_off function currently assumes that the poweroff GPIO pin
is configured for use via the ARM side, but the upcoming GPIO driver
configures all pins for use via the PPC side, breaking poweroff.
Configure the owner register explicitly in wii_power_off to make
wii_power_off work with and without the new GPIO driver.
I think the Wii can be switched to the generic gpio-poweroff driver,
after the GPIO driver is merged.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Previously, wii_device_probe would only initialize devices under the
/hollywood node. After this patch, platform devices placed outside of
/hollywood will also be initialized.
The intended usecase for this are devices located outside of the
Hollywood chip, such as GPIO LEDs and GPIO buttons.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On 64-bit Book3E systems, in setup_tlb_core_data() we reference other
CPUs pacas. But in commit 59f577743d ("powerpc/64: Defer paca
allocation until memory topology is discovered") the allocation of
non-boot-CPU pacas was deferred until later in boot.
This leads to an oops:
CPU maps initialized for 1 thread per core
Unable to handle kernel paging request for data at address 0x8888888888888918
Faulting instruction address: 0xc000000000e2f0d0
Oops: Kernel access of bad area, sig: 11 [#1]
NIP .setup_tlb_core_data+0xdc/0x160
Call Trace:
.setup_tlb_core_data+0x5c/0x160 (unreliable)
.setup_arch+0x80/0x348
.start_kernel+0x7c/0x598
start_here_common+0x1c/0x40
Luckily setup_tlb_core_data() is called immediately prior to
smp_setup_pacas(). So simply switching their order is sufficient to
fix the oops and seems unlikely to have any other unwanted side
effects.
Fixes: 59f577743d ("powerpc/64: Defer paca allocation until memory topology is discovered")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
SLOF checks for 'sc 1' (hypercall) support by issuing a hcall with
H_SET_DABR. Since the recent commit e8ebedbf31 ("KVM: PPC: Book3S
HV: Return error from h_set_dabr() on POWER9") changed H_SET_DABR to
return H_UNSUPPORTED on Power9, we see guest boot failures, the
symptom is the boot seems to just stop in SLOF, eg:
SLOF ***************************************************************
QEMU Starting
Build Date = Sep 24 2017 12:23:07
FW Version = buildd@ release 20170724
<no further output>
SLOF can cope if H_SET_DABR returns H_HARDWARE. So wwitch the return
value to H_HARDWARE instead of H_UNSUPPORTED so that we don't break
the guest boot.
That does mean we return a different error to PowerVM in this case,
but that's probably not a big concern.
Fixes: e8ebedbf31 ("KVM: PPC: Book3S HV: Return error from h_set_dabr() on POWER9")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Bring in yet another series that touches KVM code, and might need to
be merged into the kvm-ppc branch to resolve conflicts.
This required some changes in pnv_power9_force_smt4_catch/release()
due to the paca array becomming an array of pointers.
PPC:
- Fix a bug causing occasional machine check exceptions on POWER8 hosts
(introduced in 4.16-rc1)
x86:
- Fix a guest crashing regression with nested VMX and restricted guest
(introduced in 4.16-rc1)
- Fix dependency check for pv tlb flush (The wrong dependency that
effectively disabled the feature was added in 4.16-rc4, the original
feature in 4.16-rc1, so it got decent testing.)
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJavUt5AAoJEED/6hsPKofo8uQH/RuijrsAIUnymkYY+6BYFXlh
Ri8qhG8VB+C3SpWEtsqcqNVkjJTepCD2Ej5BJTL4Gc9BSTWy7Ht6kqskEgwcnzu2
xRfkg0q0vTj1+GDd+UiTZfxiinoHtB9x3fiXali5UNTCd1fweLxdidETfO+GqMMq
KDhTR+S8dXE5VG7r+iJ80LZPtHQJ94f0fh9XpQk3X2ExTG5RBxag1U2nCfiKRAZk
xRv1CNAxNaBxS38CgYfHzg31NJx38fnq/qREsIdOx0Ju9WQkglBFkhLAGUb4vL0I
nn8YX/oV9cW2G8tyPWjC245AouABOLbzu0xyj5KgCY/z1leA9tdLFX/ET6Zye+E=
=++uZ
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Radim Krčmář:
"PPC:
- Fix a bug causing occasional machine check exceptions on POWER8
hosts (introduced in 4.16-rc1)
x86:
- Fix a guest crashing regression with nested VMX and restricted
guest (introduced in 4.16-rc1)
- Fix dependency check for pv tlb flush (the wrong dependency that
effectively disabled the feature was added in 4.16-rc4, the
original feature in 4.16-rc1, so it got decent testing)"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: Fix pv tlb flush dependencies
KVM: nVMX: sync vmcs02 segment regs prior to vmx_set_cr0
KVM: PPC: Book3S HV: Fix duplication of host SLB entries
We need to zero-out pgd table only if we share the slab cache with
pud/pmd level caches. With the support of 4PB, we don't share the slab
cache anymore. Instead of removing the code completely hide it within
an #ifdef. We don't need to do this with any other page table level,
because they all allocate table of double the size and we take of
initializing the first half corrrectly during page table zap.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[mpe: Consolidate multiple #if / #ifdef into one]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch increases the max virtual (effective) address value to 4PB.
With 4K page size config we continue to limit ourself to 64TB.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[mpe: Keep the H_PGTABLE_RANGE test, update it to work]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
For addresses above 512TB we allocate additional mmu contexts. To make
it all easy, addresses above 512TB are handled with IR/DR=1 and with
stack frame setup.
The mmu_context_t is also updated to track the new extended_ids. To
support upto 4PB we need a total 8 contexts.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[mpe: Minor formatting tweaks and comment wording, switch BUG to WARN
in get_ea_context().]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In a following patch, on finding a free area we will need to do
allocatinon of extra contexts as needed. Consolidating the return path
for slice_get_unmapped_area() will make that easier.
Split into a separate patch to make review easy.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Memory keys are supported only with hash translation mode. Instead of
using #ifdef in generic code move the key related pte bits to
respective headers
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
asm/barrier.h is not always included after asm/synch.h, which meant
it was missing __SUBARCH_HAS_LWSYNC, so in some files smp_wmb() would
be eieio when it should be lwsync. kernel/time/hrtimer.c is one case.
__SUBARCH_HAS_LWSYNC is only used in one place, so just fold it in
to where it's used. Previously with my small simulator config, 377
instances of eieio in the tree. After this patch there are 55.
Fixes: 46d075be58 ("powerpc: Optimise smp_wmb")
Cc: stable@vger.kernel.org # v2.6.29+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
[mpe: Add missing ';' to make it compile]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
thread_pkey_regs_init() initializes the pkey related registers
instead of initializing the fields in the task structures. Fortunately
those key related registers are re-set to zero when the task
gets scheduled on the cpu. However its good to fix this glaringly
visible error.
Fixes: 06bb53b338 ("powerpc: store and restore the pkey state across context switches")
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Ellerman reported the following call trace when running
ftracetest:
BUG: using __this_cpu_write() in preemptible [00000000] code: ftracetest/6178
caller is opt_pre_handler+0xc4/0x110
CPU: 1 PID: 6178 Comm: ftracetest Not tainted 4.15.0-rc7-gcc6x-gb2cd1df #1
Call Trace:
[c0000000f9ec39c0] [c000000000ac4304] dump_stack+0xb4/0x100 (unreliable)
[c0000000f9ec3a00] [c00000000061159c] check_preemption_disabled+0x15c/0x170
[c0000000f9ec3a90] [c000000000217e84] opt_pre_handler+0xc4/0x110
[c0000000f9ec3af0] [c00000000004cf68] optimized_callback+0x148/0x170
[c0000000f9ec3b40] [c00000000004d954] optinsn_slot+0xec/0x10000
[c0000000f9ec3e30] [c00000000004bae0] kretprobe_trampoline+0x0/0x10
This is showing up since OPTPROBES is now enabled with CONFIG_PREEMPT.
trampoline_probe_handler() considers itself to be a special kprobe
handler for kretprobes. In doing so, it expects to be called from
kprobe_handler() on a trap, and re-enables preemption before returning a
non-zero return value so as to suppress any subsequent processing of the
trap by the kprobe_handler().
However, with optprobes, we don't deal with special handlers (we ignore
the return code) and just try to re-enable preemption causing the above
trace.
To address this, modify trampoline_probe_handler() to not be special.
The only additional processing done in kprobe_handler() is to emulate
the instruction (in this case, a 'nop'). We adjust the value of
regs->nip for the purpose and delegate the job of re-enabling
preemption and resetting current kprobe to the probe handlers
(kprobe_handler() or optimized_callback()).
Fixes: 8a2d71a3f2 ("powerpc/kprobes: Disable preemption before invoking probe handler for optprobes")
Cc: stable@vger.kernel.org # v4.15+
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
opal_nvram_write currently just assumes success if it encounters an
error other than OPAL_BUSY or OPAL_BUSY_EVENT. Have it return -EIO
on other errors instead.
Fixes: 628daa8d5a ("powerpc/powernv: Add RTC and NVRAM support plus RTAS fallbacks")
Cc: stable@vger.kernel.org # v3.2+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Acked-by: Stewart Smith <stewart@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The H_CPU_BEHAV_* flags should be checked for in the 'behaviour' field
of 'struct h_cpu_char_result' -- 'character' is for H_CPU_CHAR_*
flags.
Found by playing around with QEMU's implementation of the hypercall:
H_CPU_CHAR=0xf000000000000000
H_CPU_BEHAV=0x0000000000000000
This clears H_CPU_BEHAV_FAVOUR_SECURITY and H_CPU_BEHAV_L1D_FLUSH_PR
so pseries_setup_rfi_flush() disables 'rfi_flush'; and it also
clears H_CPU_CHAR_L1D_THREAD_PRIV flag. So there is no RFI flush
mitigation at all for cpu_show_meltdown() to report; but currently
it does:
Original kernel:
# cat /sys/devices/system/cpu/vulnerabilities/meltdown
Mitigation: RFI Flush
Patched kernel:
# cat /sys/devices/system/cpu/vulnerabilities/meltdown
Not affected
H_CPU_CHAR=0x0000000000000000
H_CPU_BEHAV=0xf000000000000000
This sets H_CPU_BEHAV_BNDS_CHK_SPEC_BAR so cpu_show_spectre_v1() should
report vulnerable; but currently it doesn't:
Original kernel:
# cat /sys/devices/system/cpu/vulnerabilities/spectre_v1
Not affected
Patched kernel:
# cat /sys/devices/system/cpu/vulnerabilities/spectre_v1
Vulnerable
Brown-paper-bag-by: Michael Ellerman <mpe@ellerman.id.au>
Fixes: f636c14790 ("powerpc/pseries: Set or clear security feature flags")
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Try to allocate kernel page tables for direct mapping and vmemmap
according to the node of the memory they will map. The node is not
available for the linear map in early boot, so use range allocation
to allocate the page tables from the region they map, which is
effectively node-local.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Fix build error in radix__create_section_mapping()]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Per-node allocations are possible on 64s with radix that does
not have the bolted SLB limitation.
Hash would be able to do the same if all CPUs had the bottom of
their node-local memory bolted as well. This is left as an
exercise for the reader.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Add dummy definition of boot_cpuid for !SMP]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Rename the dummy allocate_pacas() to fix 32-bit build]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Build an array that finds hardware CPU number from logical CPU
number in firmware CPU discovery. Use that rather than setting
paca of other CPUs directly, to begin with. Subsequent patch will
not have pacas allocated at this point.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Fix SMP=n build by adding #ifdef in arch_match_cpu_phys_id()]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Move this into the early setup code, and don't iterate over CPU masks.
We don't want to call into sysfs so early from setup, and a future patch
won't initialize CPU masks by the time this is called.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Fold in incremental fix from Nick for DSCR handling]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Split sparsemem initialisation from basic numa topology discovery.
Move the parsing earlier in boot, before pacas are allocated.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
slb_shadow structures are avoided for radix environment.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We no longer allocate lppacas in an array, so this patch removes the
1kB static alignment for the structure, and enforces the PAPR
alignment requirements at allocation time. We can not reduce the 1kB
allocation size however, due to existing KVM hypervisors.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Change the paca array into an array of pointers to pacas. Allocate
pacas individually.
This allows flexibility in where the PACAs are allocated. Future work
will allocate them node-local. Platforms that don't have address limits
on PACAs would be able to defer PACA allocations until later in boot
rather than allocate all possible ones up-front then freeing unused.
This is slightly more overhead (one additional indirection) for cross
CPU paca references, but those aren't too common.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The "lppaca" is a structure registered with the hypervisor. This is
unnecessary when running on non-virtualised platforms. One field from
the lppaca (pmcregs_in_use) is also used by the host, so move the host
part out into the paca (lppaca field is still updated in
guest mode).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Fix non-pseries build with some #ifdefs]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In mpic_physmask() we loop over all CPUs up to 32, then get the hard
SMP processor id of that CPU.
Currently that's possibly walking off the end of the paca array, but
in a future patch we will change the paca array to be an array of
pointers, and in that case we will get a NULL for missing CPUs and
oops. eg:
Unable to handle kernel paging request for data at address 0x88888888888888b8
Faulting instruction address: 0xc00000000004e380
Oops: Kernel access of bad area, sig: 11 [#1]
...
NIP .mpic_set_affinity+0x60/0x1a0
LR .irq_do_set_affinity+0x48/0x100
Fix it by checking the CPU is possible, this also fixes the code if
there are gaps in the CPU numbering which probably never happens on
mpic systems but who knows.
Debugged-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
- Improvements for the radix page fault handler for HV KVM on POWER9.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJavHlMAAoJEJ2a6ncsY3GfWTAIANbY6b8xvhUY6c3WM1dt6o78
6MWJW1vCcsDYuM5yyIjYTds2xjY6vm7oWbo9thDdLIE9sWP2uKBDbdem8KxZb6JL
t/tdzuLOYkB60BfwQL0z77UmLlHSQYF5RfJjbYVe5oXt7OU5TCe43udkHsT9QtLH
HTpxvl7ebf2TIoex1+XqrD0eJ93tSOVFWB7Ay7WRUQu08CMEQRcHaszyMqdNfHfs
LHoPwLgxyWf+7/zt2T4++ebfysQDFpQgsEuEBugXkaHkw6pSGi6R+BOrZwVVmcGm
jiHq5+mdho3wL+B47Rt7UTjkpsMLyFbWR6TrhMD7y84/CislizKhEdnEYymKwH4=
=0igD
-----END PGP SIGNATURE-----
Merge tag 'kvm-ppc-next-4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
KVM PPC update for 4.17
- Improvements for the radix page fault handler for HV KVM on POWER9.
These are actually all fixes for pre-4.16 code, or new hardware workarounds.
Fix missing AT_BASE_PLATFORM (in auxv) when we're using a new firmware interface
for describing CPU features.
Fix lost pending interrupts due to a race in our interrupt soft-masking code.
A workaround for a nest MMU bug with TLB invalidations on Power9.
A workaround for broadcast TLB invalidations on Power9.
Fix a bug in our instruction SLB miss handler, when handling bad addresses
(eg. >= TASK_SIZE), which could corrupt non-volatile user GPRs.
Thanks to:
Aneesh Kumar K.V, Balbir Singh, Benjamin Herrenschmidt, Nicholas Piggin.
-----BEGIN PGP SIGNATURE-----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=qP8V
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.16-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Some more powerpc fixes for 4.16. Apologies if this is a bit big at
rc7, but they're all reasonably important fixes. None are actually for
new code, so they aren't indicative of 4.16 being in bad shape from
our point of view.
- Fix missing AT_BASE_PLATFORM (in auxv) when we're using a new
firmware interface for describing CPU features.
- Fix lost pending interrupts due to a race in our interrupt
soft-masking code.
- A workaround for a nest MMU bug with TLB invalidations on Power9.
- A workaround for broadcast TLB invalidations on Power9.
- Fix a bug in our instruction SLB miss handler, when handling bad
addresses (eg. >= TASK_SIZE), which could corrupt non-volatile user
GPRs.
Thanks to: Aneesh Kumar K.V, Balbir Singh, Benjamin Herrenschmidt,
Nicholas Piggin"
* tag 'powerpc-4.16-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64s: Fix i-side SLB miss bad address handler saving nonvolatile GPRs
powerpc/mm: Fixup tlbie vs store ordering issue on POWER9
powerpc/mm/radix: Move the functions that does the actual tlbie closer
powerpc/mm/radix: Remove unused code
powerpc/mm: Workaround Nest MMU bug with TLB invalidations
powerpc/mm: Add tracking of the number of coprocessors using a context
powerpc/64s: Fix lost pending interrupt due to race causing lost update to irq_happened
powerpc/64s: Fix NULL AT_BASE_PLATFORM when using DT CPU features
Merge our fixes branch from the 4.16 cycle.
There were a number of important fixes merged, in particular some Power9
workarounds that we want in next for testing purposes. There's also been
some conflicting changes in the CPU features code which are best merged
and tested before going upstream.
This changes the hypervisor page fault handler for radix guests to use
the generic KVM __gfn_to_pfn_memslot() function instead of using
get_user_pages_fast() and then handling the case of VM_PFNMAP vmas
specially. The old code missed the case of VM_IO vmas; with this
change, VM_IO vmas will now be handled correctly by code within
__gfn_to_pfn_memslot.
Currently, __gfn_to_pfn_memslot calls hva_to_pfn, which only uses
__get_user_pages_fast for the initial lookup in the cases where
either atomic or async is set. Since we are not setting either
atomic or async, we do our own __get_user_pages_fast first, for now.
This also adds code to check for the KVM_MEM_READONLY flag on the
memslot. If it is set and this is a write access, we synthesize a
data storage interrupt for the guest.
In the case where the page is not normal RAM (i.e. page == NULL in
kvmppc_book3s_radix_page_fault(), we read the PTE from the Linux page
tables because we need the mapping attribute bits as well as the PFN.
(The mapping attribute bits indicate whether accesses have to be
non-cacheable and/or guarded.)
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Using the DAWR on POWER9 can cause xstops, hence we need to disable
it.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This disables the DAWR on all POWER9 CPUs via cpu feature quirk.
Using the DAWR on POWER9 can cause xstops, hence we need to disable
it.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
POWER9 with the DAWR disabled causes problems for partition
migration. Either we have to fail the migration (since we lose the
DAWR) or we silently drop the DAWR and allow the migration to pass.
This patch does the latter and allows the migration to pass (at the
cost of silently losing the DAWR). This is not ideal but hopefully the
best overall solution. This approach has been acked by Paulus.
With this patch kvmppc_set_one_reg() will store the DAWR in the vcpu
but won't actually set it on POWER9 hardware.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
POWER7 compat mode guests can use h_set_dabr on POWER9. POWER9 should
use the DAWR but since it's disabled there we can't.
This returns H_UNSUPPORTED on a h_set_dabr() on POWER9 where the DAWR
is disabled.
Current Linux guests ignore this error, so they will silently not get
the DAWR (sigh). The same error code is being used by POWERVM in this
case.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Return H_P2 on a h_set_mode(SET_DAWR) on POWER9 where the DAWR is
disabled.
Current Linux guests ignore this error, so they will silently not get
the DAWR (sigh). The same error code is being used by POWERVM in this
case.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The 'bd' command will now print an error and not set the breakpoint on
P9.
Signed-off-by: Michael Neuling <mikey@neuling.org>
[mpe: Unsplit quoted string]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This updates the ptrace code to use ppc_breakpoint_available().
We now advertise via PPC_PTRACE_GETHWDBGINFO zero breakpoints when the
DAWR is missing (ie. POWER9). This results in GDB falling back to
software emulation of the breakpoint (which is slow).
For the features advertised by PPC_PTRACE_GETHWDBGINFO, we keep
advertising DAWR as if we don't GDB assumes 1 breakpoint irrespective
of the number of breakpoints advertised. GDB then fails later when
trying to set this one breakpoint.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add ppc_breakpoint_available() to determine if a breakpoint is
available currently via the DAWR or DABR.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Checking for a "fully active" device state requires testing two flag
bits, which is open coded in several places, so add a function to do
it.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The caller will always pass NULL for 'rmv_data' when
'eeh_aware_driver' is true, so the first two calls to
eeh_pe_dev_traverse() can be combined without changing behaviour as
can the two arms of the final 'if' block.
This should not change behaviour.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
eeh_reset_device() tests the value of 'bus' more than once but the
only caller, eeh_handle_normal_device() does this test itself and will
never pass NULL.
So, remove the dead tests.
This should not change behaviour.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
It is currently difficult to understand the behaviour of
eeh_reset_device() due to the way it's parameters are used. In
particular, when 'bus' is NULL, it's value is still necessary so the
same value is looked up again locally under a different name
('frozen_bus') but behaviour is changed.
To clarify this, add a new parameter 'driver_eeh_aware', and have the
caller set it when it would have passed NULL for 'bus' and always pass
a value for 'bus'. Then change any test that was on 'bus' to one on
'!driver_eeh_aware' and replace uses of 'frozen_bus' with 'bus'.
Also update the function's comment.
This should not change behaviour.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The name "frozen_bus" is misleading: it's not necessarily frozen, it's
just the PE's PCI bus.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Remove a test that checks if "frozen_bus" is NULL, because it cannot
have changed since it was tested at the start of the function and so
must be true here.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit "0ba178888b05 powerpc/eeh: Remove reference to PCI device"
removed a call to pci_dev_get() from __eeh_addr_cache_get_device() but
did not update the comment to match.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently the EEH_PE_RECOVERING flag for a PE is managed by both the
caller and callee of eeh_handle_normal_event() (among other places not
considered here). This is complicated by the fact that the PE may
or may not have been invalidated by the call.
So move the callee's handling into eeh_handle_normal_event(), which
clarifies it and allows the return type to be changed to void (because
it no longer needs to indicate at the PE has been invalidated).
This should not change behaviour except in eeh_event_handler() where
it was previously possible to cause eeh_pe_state_clear() to be called
on an invalid PE, which is now avoided.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The function eeh_handle_event(pe) does nothing other than switching
between calling eeh_handle_normal_event(pe) and
eeh_handle_special_event(). However it is only called in two places,
one where pe can't be NULL and the other where it must be NULL (see
eeh_event_handler()) so it does nothing but obscure the flow of
control.
So, remove it.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
GPUs and the corresponding NVLink bridges get different PEs as they
have separate translation validation entries (TVEs). We put these PEs
to the same IOMMU group so they cannot be passed through separately.
So the iommu_table_group_ops::set_window/unset_window for GPUs do set
tables to the NPU PEs as well which means that iommu_table's list of
attached PEs (iommu_table_group_link) has both GPU and NPU PEs linked.
This list is used for TCE cache invalidation.
The problem is that NPU PE has just a single TVE and can be programmed
to point to 32bit or 64bit windows while GPU PE has two (as any other
PCI device). So we end up having an 32bit iommu_table struct linked to
both PEs even though only the 64bit TCE table cache can be invalidated
on NPU. And a relatively recent skiboot detects this and prints
errors.
This changes GPU's iommu_table_group_ops::set_window/unset_window to
make sure that NPU PE is only linked to the table actually used by the
hardware. If there are two tables used by an IOMMU group, the NPU PE
will use the last programmed one which with the current use scenarios
is expected to be a 64bit one.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With enabled DEBUG, there is a compile error:
"error: ‘flags’ is used uninitialized in this function".
This moves pr_devel() little further where @flags are initialized.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently the pseries kernel advertises radix MMU support even if
the actual support is disabled via the CONFIG_PPC_RADIX_MMU option.
This adds a check for CONFIG_PPC_RADIX_MMU to avoid advertising radix
to the hypervisor.
Suggested-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fix the warning messages for stop_machine_change_mapping(), and a number
of other affected functions in its call chain.
All modified functions are under CONFIG_MEMORY_HOTPLUG, so __meminit
is okay (keeps them / does not discard them).
Boot-tested on powernv/power9/radix-mmu and pseries/power8/hash-mmu.
$ make -j$(nproc) CONFIG_DEBUG_SECTION_MISMATCH=y vmlinux
...
MODPOST vmlinux.o
WARNING: vmlinux.o(.text+0x6b130): Section mismatch in reference from the function stop_machine_change_mapping() to the function .meminit.text:create_physical_mapping()
The function stop_machine_change_mapping() references
the function __meminit create_physical_mapping().
This is often because stop_machine_change_mapping lacks a __meminit
annotation or the annotation of create_physical_mapping is wrong.
WARNING: vmlinux.o(.text+0x6b13c): Section mismatch in reference from the function stop_machine_change_mapping() to the function .meminit.text:create_physical_mapping()
The function stop_machine_change_mapping() references
the function __meminit create_physical_mapping().
This is often because stop_machine_change_mapping lacks a __meminit
annotation or the annotation of create_physical_mapping is wrong.
...
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a definition for cpu_show_spectre_v2() to override the generic
version. This has several permuations, though in practice some may not
occur we cater for any combination.
The most verbose is:
Mitigation: Indirect branch serialisation (kernel only), Indirect
branch cache disabled, ori31 speculation barrier enabled
We don't treat the ori31 speculation barrier as a mitigation on its
own, because it has to be *used* by code in order to be a mitigation
and we don't know if userspace is doing that. So if that's all we see
we say:
Vulnerable, ori31 speculation barrier enabled
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a definition for cpu_show_spectre_v1() to override the generic
version. Currently this just prints "Not affected" or "Vulnerable"
based on the firmware flag.
Although the kernel does have array_index_nospec() in a few places, we
haven't yet audited all the powerpc code to see where it's necessary,
so for now we don't list that as a mitigation.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that we have the security flags we can simplify the code in
pseries_setup_rfi_flush() because the security flags have pessimistic
defaults.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that we have the security flags we can significantly simplify the
code in pnv_setup_rfi_flush(), because we can use the flags instead of
checking device tree properties and because the security flags have
pessimistic defaults.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that we have the security feature flags we can make the
information displayed in the "meltdown" file more informative.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This landed in setup_64.c for no good reason other than we had nowhere
else to put it. Now that we have a security-related file, that is a
better place for it so move it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that we have feature flags for security related things, set or
clear them based on what we see in the device tree provided by
firmware.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that we have feature flags for security related things, set or
clear them based on what we receive from the hypercall.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This commit adds security feature flags to reflect the settings we
receive from firmware regarding Spectre/Meltdown mitigations.
The feature names reflect the names we are given by firmware on bare
metal machines. See the hostboot source for details.
Arguably these could be firmware features, but that then requires them
to be read early in boot so they're available prior to asm feature
patching, but we don't actually want to use them for patching. We may
also want to dynamically update them in future, which would be
incompatible with the way firmware features work (at the moment at
least). So for now just make them separate flags.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We might have migrated to a machine that uses a different flush type,
or doesn't need flushing at all.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently the rfi-flush messages print 'Using <type> flush' for all
enabled_flush_types, but that is not necessarily true -- as now the
fallback flush is always enabled on pseries, but the fixup function
overwrites its nop/branch slot with other flush types, if available.
So, replace the 'Using <type> flush' messages with '<type> flush is
available'.
Also, print the patched flush types in the fixup function, so users
can know what is (not) being used (e.g., the slower, fallback flush,
or no flush type at all if flush is disabled via the debugfs switch).
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This ensures the fallback flush area is always allocated on pseries,
so in case a LPAR is migrated from a patched to an unpatched system,
it is possible to enable the fallback flush in the target system.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
For PowerVM migration we want to be able to call setup_rfi_flush()
again after we've migrated the partition.
To support that we need to check that we're not trying to allocate the
fallback flush area after memblock has gone away (i.e., boot-time only).
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
rfi_flush_enable() includes a check to see if we're already
enabled (or disabled), and in that case does nothing.
But that means calling setup_rfi_flush() a 2nd time doesn't actually
work, which is a bit confusing.
Move that check into the debugfs code, where it really belongs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
These events either do not count, or do not count correctly, so to
prevent user confusion block counting them at all.
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
[mpe: Change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
These events either do not count, or do not count correctly, so to
prevent user confusion block counting them at all.
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
[mpe: Change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Introduce code to support addition of blacklisted events for a
processor version. Blacklisted events are events that are known to not
count correctly on that CPU revision, and so should be prevented from
being counted so as to avoid user confusion.
A 'pointer' and 'int' variable to hold the number of events are added
to 'struct power_pmu', along with a generic function to loop through
the list to validate the given event. Generic function
'is_event_blacklisted' is called in power_pmu_event_init() to detect
and reject early.
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Sampled Data Address Register (SDAR) is a 64-bit register that
contains the effective address of the storage operand of an
instruction that was being executed, possibly out-of-order, at or
around the time that the Performance Monitor alert occurred.
In certain scenario SDAR happen to contain the kernel address even for
userspace only sampling. Add checks to prevent it.
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The current Branch History Rolling Buffer (BHRB) code does not check
for any privilege levels before updating the data from BHRB. This
could leak kernel addresses to userspace even when profiling only with
userspace privileges. Add proper checks to prevent it.
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Current code in power_pmu_disable() does not clear the sampling
registers like Sampling Instruction Address Register (SIAR) and
Sampling Data Address Register (SDAR) after disabling the PMU. Since
these are userspace readable and could contain kernel addresses, add
code to explicitly clear the content of these registers.
Also add a "context synchronizing instruction" to enforce no further
updates to these registers as suggested by Power ISA v3.0B. From
section 9.4, on page 1108:
"If an mtspr instruction is executed that changes the value of a
Performance Monitor register other than SIAR, SDAR, and SIER, the
change is not guaranteed to have taken effect until after a
subsequent context synchronizing instruction has been executed (see
Chapter 11. "Synchronization Requirements for Context Alterations"
on page 1133)."
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
[mpe: Massage change log and add ISA reference]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On POWER9, since commit cc3d294013 ("powerpc/64: Enable use of radix
MMU under hypervisor on POWER9", 2017-01-30), we set both the radix and
HPT bits in the client-architecture-support (CAS) vector, which tells
the hypervisor that we can do either radix or HPT. According to PAPR,
if we use this combination we are promising to do a H_REGISTER_PROC_TBL
hcall later on to let the hypervisor know whether we are doing radix
or HPT. We currently do this call if we are doing radix but not if
we are doing HPT. If the hypervisor is able to support both radix
and HPT guests, it would be entitled to defer allocation of the HPT
until the H_REGISTER_PROC_TBL call, and to fail any attempts to create
HPTEs until the H_REGISTER_PROC_TBL call. Thus we need to do a
H_REGISTER_PROC_TBL call when we are doing HPT; otherwise we may
crash at boot time.
This adds the code to call H_REGISTER_PROC_TBL in this case, before
we attempt to create any HPT entries using H_ENTER.
Fixes: cc3d294013 ("powerpc/64: Enable use of radix MMU under hypervisor on POWER9")
Cc: stable@vger.kernel.org # v4.11+
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The SLB bad address handler's trap number fixup does not preserve the
low bit that indicates nonvolatile GPRs have not been saved. This
leads save_nvgprs to skip saving them, and subsequent functions and
return from interrupt will think they are saved.
This causes kernel branch-to-garbage debugging to not have correct
registers, can also cause userspace to have its registers clobbered
after a segfault.
Fixes: f0f558b131 ("powerpc/mm: Preserve CFAR value on SLB miss caused by access to bogus address")
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
stat(1) is not standardized and different implementations have their own
(conflicting) flags for querying the size of a file.
ls(1) provides the same information (value of st.st_size) in the 5th
column, except when the file is a character or block device. This output
is standardized[0]. The -n option turns on -l, which writes lines
formatted like
"%s %u %s %s %u %s %s\n", <file mode>, <number of links>,
<owner name>, <group name>, <size>, <date and time>,
<pathname>
but instead of writing the <owner name> and <group name>, it writes the
numeric owner and group IDs (this avoids /etc/passwd and /etc/group
lookups as well as potential field splitting issues).
The <size> field is specified as "the value that would be returned for
the file in the st_size field of struct stat".
To avoid duplicating logic in several locations in the tree, create
scripts/file-size.sh and update callers to use that instead of stat(1).
[0] http://pubs.opengroup.org/onlinepubs/9699919799/utilities/ls.html#tag_20_73_10
Signed-off-by: Michael Forney <forney@google.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Incremental linking is gone, so rename built-in.o to built-in.a, which
is the usual extension for archive files.
This patch does two things, first is a simple search/replace:
git grep -l 'built-in\.o' | xargs sed -i 's/built-in\.o/built-in\.a/g'
The second is to invert nesting of nested text manipulations to avoid
filtering built-in.a out from libs-y2:
-libs-y2 := $(filter-out %.a, $(patsubst %/, %/built-in.a, $(libs-y)))
+libs-y2 := $(patsubst %/, %/built-in.a, $(filter-out %.a, $(libs-y)))
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This works around a hardware bug in "Nimbus" POWER9 DD2.2 processors,
where the contents of the TEXASR can get corrupted while a thread is
in fake suspend state. The workaround is for the instruction emulation
code to use the value saved at the most recent guest exit in real
suspend mode. We achieve this by simply not saving the TEXASR into
the vcpu struct on an exit in fake suspend state. We also have to
take care to set the orig_texasr field only on guest exit in real
suspend state.
This also means that on guest entry in fake suspend state, TEXASR
will be restored to the value it had on the last exit in real suspend
state, effectively counteracting any hardware-caused corruption. This
works because TEXASR may not be written in suspend state.
With this, the guest might see the wrong values in TEXASR if it reads
it while in suspend state, but will see the correct value in
non-transactional state (e.g. after a treclaim), and treclaim will
work correctly.
With this workaround, the code will actually run slightly faster, and
will operate correctly on systems without the TEXASR bug (since TEXASR
may not be written in suspend state, and is only changed by failure
recording, which will have already been done before we get into fake
suspend state). Therefore these changes are not made subject to a CPU
feature bit.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This works around a hardware bug in "Nimbus" POWER9 DD2.2 processors,
where a treclaim performed in fake suspend mode can cause subsequent
reads from the XER register to return inconsistent values for the SO
(summary overflow) bit. The inconsistent SO bit state can potentially
be observed on any thread in the core. We have to do the treclaim
because that is the only way to get the thread out of suspend state
(fake or real) and into non-transactional state.
The workaround for the bug is to force the core into SMT4 mode before
doing the treclaim. This patch adds the code to do that, conditional
on the CPU_FTR_P9_TM_XER_SO_BUG feature bit.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
POWER9 has hardware bugs relating to transactional memory and thread
reconfiguration (changes to hardware SMT mode). Specifically, the core
does not have enough storage to store a complete checkpoint of all the
architected state for all four threads. The DD2.2 version of POWER9
includes hardware modifications designed to allow hypervisor software
to implement workarounds for these problems. This patch implements
those workarounds in KVM code so that KVM guests see a full, working
transactional memory implementation.
The problems center around the use of TM suspended state, where the
CPU has a checkpointed state but execution is not transactional. The
workaround is to implement a "fake suspend" state, which looks to the
guest like suspended state but the CPU does not store a checkpoint.
In this state, any instruction that would cause a transition to
transactional state (rfid, rfebb, mtmsrd, tresume) or would use the
checkpointed state (treclaim) causes a "soft patch" interrupt (vector
0x1500) to the hypervisor so that it can be emulated. The trechkpt
instruction also causes a soft patch interrupt.
On POWER9 DD2.2, we avoid returning to the guest in any state which
would require a checkpoint to be present. The trechkpt in the guest
entry path which would normally create that checkpoint is replaced by
either a transition to fake suspend state, if the guest is in suspend
state, or a rollback to the pre-transactional state if the guest is in
transactional state. Fake suspend state is indicated by a flag in the
PACA plus a new bit in the PSSCR. The new PSSCR bit is write-only and
reads back as 0.
On exit from the guest, if the guest is in fake suspend state, we still
do the treclaim instruction as we would in real suspend state, in order
to get into non-transactional state, but we do not save the resulting
register state since there was no checkpoint.
Emulation of the instructions that cause a softpatch interrupt is
handled in two paths. If the guest is in real suspend mode, we call
kvmhv_p9_tm_emulation_early() to handle the cases where the guest is
transitioning to transactional state. This is called before we do the
treclaim in the guest exit path; because we haven't done treclaim, we
can get back to the guest with the transaction still active. If the
instruction is a case that kvmhv_p9_tm_emulation_early() doesn't
handle, or if the guest is in fake suspend state, then we proceed to
do the complete guest exit path and subsequently call
kvmhv_p9_tm_emulation() in host context with the MMU on. This handles
all the cases including the cases that generate program interrupts
(illegal instruction or TM Bad Thing) and facility unavailable
interrupts.
The emulation is reasonably straightforward and is mostly concerned
with checking for exception conditions and updating the state of
registers such as MSR and CR0. The treclaim emulation takes care to
ensure that the TEXASR register gets updated as if it were the guest
treclaim instruction that had done failure recording, not the treclaim
done in hypervisor state in the guest exit path.
With this, the KVM_CAP_PPC_HTM capability returns true (1) even if
transactional memory is not available to host userspace.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
POWER9 processors up to and including "Nimbus" v2.2 have hardware
bugs relating to transactional memory and thread reconfiguration.
One of these bugs has a workaround which is to get the core into
SMT4 state temporarily. This workaround is only needed when
running bare-metal.
This patch provides a function which gets the core into SMT4 mode
by preventing threads from going to a stop state, and waking up
those which are already in a stop state. Once at least 3 threads
are not in a stop state, the core will be in SMT4 and we can
continue.
To do this, we add a "dont_stop" flag to the paca to tell the
thread not to go into a stop state. If this flag is set,
power9_idle_stop() just returns immediately with a return value
of 0. The pnv_power9_force_smt4_catch() function does the following:
1. Set the dont_stop flag for each thread in the core, except
ourselves (in fact we use an atomic_inc() in case more than
one thread is calling this function concurrently).
2. See how many threads are awake, indicated by their
requested_psscr field in the paca being 0. If this is at
least 3, skip to step 5.
3. Send a doorbell interrupt to each thread that was seen as
being in a stop state in step 2.
4. Until at least 3 threads are awake, scan the threads to which
we sent a doorbell interrupt and check if they are awake now.
This relies on the following properties:
- Once dont_stop is non-zero, requested_psccr can't go from zero to
non-zero, except transiently (and without the thread doing stop).
- requested_psscr being zero guarantees that the thread isn't in
a state-losing stop state where thread reconfiguration could occur.
- Doing stop with a PSSCR value of 0 won't be a state-losing stop
and thus won't allow thread reconfiguration.
- Once threads_per_core/2 + 1 (i.e. 3) threads are awake, the core
must be in SMT4 mode, since SMT modes are powers of 2.
This does add a sync to power9_idle_stop(), which is necessary to
provide the correct ordering between setting requested_psscr and
checking dont_stop. The overhead of the sync should be unnoticeable
compared to the latency of going into and out of a stop state.
Because some objected to incurring this extra latency on systems where
the XER[SO] bug is not relevant, I have put the test in
power9_idle_stop inside a feature section. This means that
pnv_power9_force_smt4_catch() WILL NOT WORK correctly on systems
without the CPU_FTR_P9_TM_XER_SO_BUG feature bit set, and will
probably hang the system.
In order to cater for uses where the caller has an operation that
has to be done while the core is in SMT4, the core continues to be
kept in SMT4 after pnv_power9_force_smt4_catch() function returns,
until the pnv_power9_force_smt4_release() function is called.
It undoes the effect of step 1 above and allows the other threads
to go into a stop state.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds a CPU feature bit which is set for POWER9 "Nimbus" DD2.2
processors which will be used to enable the hypervisor to assist
hardware with the handling of checkpointed register values while the
CPU is in suspend state, in order to work around hardware bugs. The
hardware assistance for these workarounds introduced a new hardware
bug relating to the XER[SO] bit. We add a separate feature bit for
this bug in case future chips fix it while still requiring the
hypervisor assistance with suspend state.
When the dt_cpu_ftrs subsystem is in use, the software assistance can
be enabled using a "tm-suspend-hypervisor-assist" node in the device
tree, and a "tm-suspend-xer-so-bug" node enables the workarounds for
the XER[SO] bug. In the absence of such nodes, a quirk enables both
for POWER9 "Nimbus" DD2.2 processors.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This moves all the CPU feature bits that are only used on 32-bit
machines to the top 20 bits of the CPU feature word and arranges
for them to be defined only in 32-bit builds. The features that
are common to 32-bit and 64-bit machines are moved to bits 0-11
of the CPU feature word. This means that for 64-bit platforms,
bits 44-63 can now be used for new features that only exist on
64-bit machines. (These bit numbers are counting from the right,
i.e. the LSB is bit 0.)
Because CPU_FTR_L3_DISABLE_NAP moved from the low 16 bits to the high
16 bits, we have to adjust some assembly code. Also, CPU_FTR_EMB_HV
moved from the high 16 bits to the low 16 bits.
Note that CPU_FTR_REAL_LE only applies to 64-bit chips, because only
64-bit chips (POWER6, 7, 8, 9) have a true little-endian mode that is
a CPU execution mode as opposed to being a page attribute.
With this we now have 20 free CPU feature bits on 64-bit machines.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The CPU_FTR_L2CSR bit is never tested anywhere, so let's reclaim the
bit.
The last usage was removed in 86d63363de ("powerpc/e500mc: Remove
dead L2 flushing code in idle_e500.S") (Jun 2015).
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
All PowerPC CPUs other than the original PPC601 have a timebase
register rather than the "real-time clock" (RTC) register that the
PPC601 (and the original POWER and POWER2 CPUs) had. Currently
we have a CPU feature bit to indicate the presence of the timebase,
but it makes more sense to use a bit to indicate the unusual
situation rather than the common situation. This therefore defines
a CPU_FTR_USE_RTC bit in place of the CPU_FTR_USE_TB bit, and
arranges for it to be set on PPC601 systems.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On POWER9, under some circumstances, a broadcast TLB invalidation
might complete before all previous stores have drained, potentially
allowing stale stores from becoming visible after the invalidation.
This works around it by doubling up those TLB invalidations which was
verified by HW to be sufficient to close the risk window.
This will be documented in a yet-to-be-published errata.
Fixes: 1a472c9dba ("powerpc/mm/radix: Add tlbflush routines")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[mpe: Enable the feature in the DT CPU features code for all Power9,
rename the feature to CPU_FTR_P9_TLBIE_BUG per benh.]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
No functionality change. Just code movement to ease code changes later
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
These function are not used in the code. Remove them.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On POWER9 the Nest MMU may fail to invalidate some translations when
doing a tlbie "by PID" or "by LPID" that is targeted at the TLB only
and not the page walk cache.
This works around it by forcing such invalidations to escalate to
RIC=2 (full invalidation of TLB *and* PWC) when a coprocessor is in
use for the context.
Fixes: 03b8abedf4 ("cxl: Enable global TLBIs for cxl contexts")
Cc: stable@vger.kernel.org # v4.15+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
[balbirs: fixed spelling and coding style to quiesce checkpatch.pl]
Tested-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently, when using coprocessors (which use the Nest MMU), we
simply increment the active_cpu count to force all TLB invalidations
to be come broadcast.
Unfortunately, due to an errata in POWER9, we will need to know
more specifically that coprocessors are in use.
This maintains a separate copros counter in the MMU context for
that purpose.
NB. The commit mentioned in the fixes tag below is not at fault for
the bug we're fixing in this commit and the next, but this fix applies
on top the infrastructure it introduced.
Fixes: 03b8abedf4 ("cxl: Enable global TLBIs for cxl contexts")
Cc: stable@vger.kernel.org # v4.15+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since commit 6964e6a4e4 ("KVM: PPC: Book3S HV: Do SLB load/unload
with guest LPCR value loaded", 2018-01-11), we have been seeing
occasional machine check interrupts on POWER8 systems when running
KVM guests, due to SLB multihit errors.
This turns out to be due to the guest exit code reloading the host
SLB entries from the SLB shadow buffer when the SLB was not previously
cleared in the guest entry path. This can happen because the path
which skips from the guest entry code to the guest exit code without
entering the guest now does the skip before the SLB is cleared and
loaded with guest values, but the host values are loaded after the
point in the guest exit path that we skip to.
To fix this, we move the code that reloads the host SLB values up
so that it occurs just before the point in the guest exit code (the
label guest_bypass:) where we skip to from the guest entry path.
Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Fixes: 6964e6a4e4 ("KVM: PPC: Book3S HV: Do SLB load/unload with guest LPCR value loaded")
Tested-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
force_external_irq_replay() can be called in the do_IRQ path with
interrupts hard enabled and soft disabled if may_hard_irq_enable() set
MSR[EE]=1. It updates local_paca->irq_happened with a load, modify,
store sequence. If a maskable interrupt hits during this sequence, it
will go to the masked handler to be marked pending in irq_happened.
This update will be lost when the interrupt returns and the store
instruction executes. This can result in unpredictable latencies,
timeouts, lockups, etc.
Fix this by ensuring hard interrupts are disabled before modifying
irq_happened.
This could cause any maskable asynchronous interrupt to get lost, but
it was noticed on P9 SMP system doing RDMA NVMe target over 100GbE,
so very high external interrupt rate and high IPI rate. The hang was
bisected down to enabling doorbell interrupts for IPIs. These provided
an interrupt type that could run at high rates in the do_IRQ path,
stressing the race.
Fixes: 1d607bb3bd ("powerpc/irq: Add mechanism to force a replay of interrupts")
Cc: stable@vger.kernel.org # v4.8+
Reported-by: Carol L. Soto <clsoto@us.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Give the basic phys_to_dma() and dma_to_phys() helpers a __-prefix and add
the memory encryption mask to the non-prefixed versions. Use the
__-prefixed versions directly instead of clearing the mask again in
various places.
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Jon Mason <jdmason@kudzu.us>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Muli Ben-Yehuda <mulix@mulix.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: iommu@lists.linux-foundation.org
Link: http://lkml.kernel.org/r/20180319103826.12853-13-hch@lst.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
'linux,stdout-path' has been deprecated for some time in favor of
'stdout-path'. Now dtc will warn on occurrences of 'linux,stdout-path'.
Search and replace all the of occurrences with 'stdout-path'.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
It's slightly less error prone to use sizeof(*foo) rather than
specifying the type.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
[mpe: Consolidate into one patch, rewrite change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The flush_dcache_phys_range() function is no longer used in the
kernel. The last usage was removed in c40785ad30 ("powerpc/dart: Use
a cachable DART").
This patch removes the function and declaration.
Signed-off-by: Matt Brown <matthew.brown.dev@gmail.com>
[mpe: Munge change log, include commit that removed last user]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch uses the vpermxor instruction to optimise the raid6 Q
syndrome. This instruction was made available with POWER8, ISA version
2.07. It allows for both vperm and vxor instructions to be done in a
single instruction. This has been tested for correctness on a ppc64le
vm with a basic RAID6 setup containing 5 drives.
The performance benchmarks are from the raid6test in the
/lib/raid6/test directory. These results are from an IBM Firestone
machine with ppc64le architecture. The benchmark results show a 35%
speed increase over the best existing algorithm for powerpc (altivec).
The raid6test has also been run on a big-endian ppc64 vm to ensure it
also works for big-endian architectures.
Performance benchmarks:
raid6: altivecx4 gen() 18773 MB/s
raid6: altivecx8 gen() 19438 MB/s
raid6: vpermxor4 gen() 25112 MB/s
raid6: vpermxor8 gen() 26279 MB/s
Signed-off-by: Matt Brown <matthew.brown.dev@gmail.com>
Reviewed-by: Daniel Axtens <dja@axtens.net>
[mpe: Add VPERMXOR macro so we can build with old binutils]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
These drivers haven't seen any recent bug fixing and are two of the last
drivers using the scsi_module.c infrastruture that has been deprecated
15 years ago.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This adds code to the radix hypervisor page fault handler to handle the
case where the guest memory is backed by 1GB hugepages, and put them
into the partition-scoped radix tree at the PUD level. The code is
essentially analogous to the code for 2MB pages. This also rearranges
kvmppc_create_pte() to make it easier to follow.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
When using the radix MMU, we can get hypervisor page fault interrupts
with the DSISR_SET_RC bit set in DSISR/HSRR1, indicating that an
attempt to set the R (reference) or C (change) bit in a PTE atomically
failed. Previously we would find the corresponding Linux PTE and
check the permission and dirty bits there, but this is not really
necessary since we only need to do what the hardware was trying to
do, namely set R or C atomically. This removes the code that reads
the Linux PTE and just update the partition-scoped PTE, having first
checked that it is still present, and if the access is a write, that
the PTE still has write permission.
Furthermore, we now check whether any other relevant bits are set
in DSISR, and if there are, then we proceed with the rest of the
function in order to handle whatever condition they represent,
instead of returning to the guest as we did previously.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This improves the handling of transparent huge pages in the radix
hypervisor page fault handler. Previously, if a small page is faulted
in to a 2MB region of guest physical space, that means that there is
a page table pointer at the PMD level, which could never be replaced
by a leaf (2MB) PMD entry. This adds the code to clear the PMD,
invlidate the page walk cache and free the page table page in this
situation, so that the leaf PMD entry can be created.
This also adds code to check whether a PMD or PTE being inserted is
the same as is already there (because of a race with another CPU that
faulted on the same page) and if so, we don't replace the existing
entry, meaning that we don't invalidate the PTE or PMD and do a TLB
invalidation.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Since commit fb1522e099 ("KVM: update to new mmu_notifier semantic
v2", 2017-08-31), the MMU notifier code in KVM no longer calls the
kvm_unmap_hva callback. This removes the PPC implementations of
kvm_unmap_hva().
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
A protection flag may not be valid across entire address space and
hence arch_validate_prot() might need the address a protection bit is
being set on to ensure it is a valid protection flag. For example, sparc
processors support memory corruption detection (as part of ADI feature)
flag on memory addresses mapped on to physical RAM but not on PFN mapped
pages or addresses mapped on to devices. This patch adds address to the
parameters being passed to arch_validate_prot() so protection bits can
be validated in the relevant context.
Signed-off-by: Khalid Aziz <khalid.aziz@oracle.com>
Cc: Khalid Aziz <khalid@gonehiking.org>
Reviewed-by: Anthony Yznaga <anthony.yznaga@oracle.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix bug leading to lost IPIs on POWER9 and hence to other CPUs reporting
lockups in smp_call_function_many().
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaqNxFAAoJEJ2a6ncsY3GfmwQH/3wz36kFHufskFhqtr3kQKYS
/LFsydZKF/8puR8CobVcvqRX/KP/WpjTvpC4GhYrto7IVPJBpuJuozSY5LDLVg9s
kw5uNQeZREFjua2Lo78/YUh+wN7Xx3LtBC/ass6QOM51dGnfeUpSiSuzGQhMrpaf
CaDVT/0M1zPcQqDvQSinsTJm5xNTJ2cO6Q2tTFtHOWQGBKB1uGxexBx9NAEO71vh
6KOgU9uIW83Vy2tubOEN6vaDEOUtm6MOwaTbFQo3Dvt7VPDoUmU099K0+EI8UBDF
/PQ/yXWaAkSrZdyDFsLWONd9jX0LrvhdNOw1bh46fPdr+SCTNp9pFRCcq3P+MhI=
=44ey
-----END PGP SIGNATURE-----
Merge tag 'kvm-ppc-fixes-4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc into kvm-master
Fix for PPC KVM for 4.16
- Fix bug leading to lost IPIs on POWER9 and hence to other CPUs reporting
lockups in smp_call_function_many().
The proper compatible for rv3029 is microcrystal,rv3029.
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The RTC core is always calling rtc_valid_tm after the read_time callback.
It is not necessary to call it just before returning from the callback.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When running virtualised the powerpc kernel is able to run the system
in "compat mode" - which means the kernel and hardware are pretending
to userspace that the CPU is an older version than it actually is.
AT_BASE_PLATFORM is an AUXV entry that we export to userspace for use
when we're running in that mode, which tells userspace the "platform"
string for the real CPU version, as opposed to the faked version.
Although we don't support compat mode when using DT CPU features, and
arguably don't need to set AT_BASE_PLATFORM, the existing cputable
based code always sets it even when we're running bare metal. That
means the lack of AT_BASE_PLATFORM is a user-visible artifact of the
fact that the kernel is using DT CPU features, which we don't want.
So set it in the DT CPU features code also.
This results in eg:
$ LD_SHOW_AUXV=1 /bin/true | grep "AT_.*PLATFORM"
AT_PLATFORM: power9
AT_BASE_PLATFORM:power9
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Add a couple of trace points in the VAS driver
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
[mpe: Add SPDX tag to new header]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When VAS is not configured, unregister the platform driver. Also simplify
cleanup by delaying vas debugfs init until we know VAS is configured.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
pnv_npu2_init_context wasn't checking the return code from
__mmu_notifier_register. If __mmu_notifier_register failed, the
npu_context was still assigned to the mm and the caller wasn't given any
indication that things went wrong. Later on pnv_npu2_destroy_context would
be called, which in turn called mmu_notifier_unregister and dropped
mm->mm_count without having incremented it in the first place. This led to
various forms of corruption like mm use-after-free and mm double-free.
__mmu_notifier_register can fail with EINTR if a signal is pending, so
this case can be frequent.
This patch calls opal_npu_destroy_context on the failure paths, and makes
sure not to assign mm->context.npu_context until past the failure points.
Signed-off-by: Mark Hairgrove <mhairgrove@nvidia.com>
Acked-By: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This fixes a bug where the trap number that is returned by
__kvmppc_vcore_entry gets corrupted. The effect of the corruption
is that IPIs get ignored on POWER9 systems when the IPI is sent via
a doorbell interrupt to a CPU which is executing in a KVM guest.
The effect of the IPI being ignored is often that another CPU locks
up inside smp_call_function_many() (and if that CPU is holding a
spinlock, other CPUs then lock up inside raw_spin_lock()).
The trap number is currently held in register r12 for most of the
assembly-language part of the guest exit path. In that path, we
call kvmppc_subcore_exit_guest(), which is a C function, without
restoring r12 afterwards. Depending on the kernel config and the
compiler, it may modify r12 or it may not, so some config/compiler
combinations see the bug and others don't.
To fix this, we arrange for the trap number to be stored on the
stack from the 'guest_bypass:' label until the end of the function,
then the trap number is loaded and returned in r12 as before.
Cc: stable@vger.kernel.org # v4.8+
Fixes: fd7bacbca4 ("KVM: PPC: Book3S HV: Fix TB corruption in guest exit path on HMI interrupt")
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This is a tidy up which removes radix MMU calls into the slice
code.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The slice_mask cache was a basic conversion which copied the slice
mask into caller's structures, because that's how the original code
worked. In most cases the pointer can be used directly instead, saving
a copy and an on-stack structure.
On POWER8, this increases vfork+exec+exit performance by 0.3%
and reduces time to mmap+munmap a 64kB page by 2%.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This code is never compiled in, and it gets broken by the next
patch, so remove it.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This converts the slice_mask bit operation helpers to be the usual
3-operand kind, which allows 2 inputs to set a different output
without an extra copy, which is used in the next patch.
Adds slice_copy_mask, which will be used in the next patch.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Rather than build slice masks from a range then use that to check for
fit in a candidate mask, implement slice_check_range_fits that checks
if a range fits in a mask directly.
This allows several structures to be removed from stacks, and also we
don't expect a huge range in a lot of these cases, so building and
comparing a full mask is going to be more expensive than testing just
one or two bits of the range.
On POWER8, this increases vfork+exec+exit performance by 0.3%
and reduces time to mmap+munmap a 64kB page by 5%.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Calculating the slice mask can become a signifcant overhead for
get_unmapped_area. This patch adds a struct slice_mask for
each page size in the mm_context, and keeps these in synch with
the slices psize arrays and slb_addr_limit.
On Book3S/64 this adds 288 bytes to the mm_context_t for the
slice mask caches.
On POWER8, this increases vfork+exec+exit performance by 9.9%
and reduces time to mmap+munmap a 64kB page by 28%.
Reduces time to mmap+munmap by about 10% on 8xx.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Make these loops look the same, and change their form so the
important part is not wrapped over so many lines.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The slice state of an mm gets zeroed then initialised upon exec.
This is the only caller of slice_set_user_psize now, so that can be
removed and instead implement a faster and simplified approach that
requires no locking or checking existing state.
This speeds up vfork+exec+exit performance on POWER8 by 3%.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that plpar_wrappers.h has an #ifdef PSERIES we can move the empty
version of plpar_set_ciabr() which xmon wants into there.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Back in 2013 we added some hypercall wrappers which misspelled
"plpar" (P-series Logical PARtition) as "plapr".
Visually they're hard to distinguish and it almost doesn't matter, but
it is confusing when grepping to miss some calls because of the typo.
They've also started spreading, so before they take over let's fix
them all to be "plpar".
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently plpar_wrappers.h is not safe to include when
CONFIG_PPC_PSERIES=n, or at least it can be depending on other config
options and so on.
Fix that by wrapping the entire content in an ifdef.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
smp_query_cpu_stopped() and related #defines are currently in
plpar_wrappers.h. The function actually does an RTAS call, not an
hcall, and basically has nothing to do with plpar_wrappers.h
Move it into pseries.h, where it can easily be used by the only two
callers in pseries/smp.c and pseries/hotplug-cpu.c.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
early_init() and machine_init() have no prototype, add one in
asm-prototypes.h.
Fixes the following warnings (treated as error in W=1):
arch/powerpc/kernel/setup_32.c:68:30: error: no previous prototype for ‘early_init’
arch/powerpc/kernel/setup_32.c:99:21: error: no previous prototype for ‘machine_init’
Signed-off-by: Mathieu Malaterre <malat@debian.org>
[mpe: Move them to asm-prototypes.h, drop other functions]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
These functions can all be static, make it so.
Signed-off-by: Mathieu Malaterre <malat@debian.org>
[mpe: Combine a patch of Mathieu's with some other static conversions]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Rewrite comparison since all values compared are of type `unsigned long`.
Instead of using unsigned properties and rewriting the original code as:
(originally suggested by Segher Boessenkool <segher@kernel.crashing.org>)
#define pfn_valid(pfn) \
(((pfn) - ARCH_PFN_OFFSET) < (max_mapnr - ARCH_PFN_OFFSET))
Prefer a static inline function to make code as readable as possible.
Fix a warning (treated as error in W=1):
arch/powerpc/include/asm/page.h:129:32: error: comparison of unsigned expression >= 0 is always true [-Werror=type-limits]
#define pfn_valid(pfn) ((pfn) >= ARCH_PFN_OFFSET && (pfn) < max_mapnr)
^
Suggested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When neither CONFIG_ALTIVEC, nor CONFIG_VSX or CONFIG_PPC64 is
defined, the array feature_properties is defined as an empty array,
which in turn triggers the following warning (treated as error on
W=1):
arch/powerpc/kernel/prom.c: In function ‘check_cpu_feature_properties’:
arch/powerpc/kernel/prom.c:298:16: error: comparison of unsigned expression < 0 is always false
for (i = 0; i < ARRAY_SIZE(feature_properties); ++i, ++fp) {
^
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add missing prototypes for ppc_select() & ppc_fadvise64_64() to header
asm-prototypes.h. Fix the following warnings (treated as errors in W=1)
arch/powerpc/kernel/syscalls.c:87:1: error: no previous prototype for ‘ppc_select’
arch/powerpc/kernel/syscalls.c:119:6: error: no previous prototype for ‘ppc_fadvise64_64’
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit 5aae8a5370 ("powerpc, hw_breakpoints: Implement
hw_breakpoints for 64-bit server processors") function
hw_breakpoint_handler() and arch_unregister_hw_breakpoint() were added
without function prototypes in hw_breakpoint.h header.
Fix the following warning(s) (treated as error in W=1):
arch/powerpc/kernel/hw_breakpoint.c:106:6: error: no previous prototype for ‘arch_unregister_hw_breakpoint’
arch/powerpc/kernel/hw_breakpoint.c:209:5: error: no previous prototype for ‘hw_breakpoint_handler’
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Two functions did not have a prototype defined in signal.h header. Fix
the following two warnings (treated as errors in W=1):
arch/powerpc/kernel/signal_32.c:1135:6: error: no previous prototype for ‘sys_rt_sigreturn’
arch/powerpc/kernel/signal_32.c:1422:6: error: no previous prototype for ‘sys_sigreturn’
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit 81e7009ea4 ("powerpc: merge ppc signal.c and ppc64
signal32.c") the function sys_debug_setcontext was added without a
prototype.
Fix compilation warning (treated as error in W=1):
arch/powerpc/kernel/signal_32.c:1227:5: error: no previous prototype for ‘sys_debug_setcontext’
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
A function init_IRQ() was added without a prototype declared in header
irq.h. Fix the following warning (treated as error in W=1):
arch/powerpc/kernel/irq.c:662:13: error: no previous prototype for ‘init_IRQ’
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit 4f8b50bbbe ("irq_work, ppc: Fix up arch hooks") a new
function arch_irq_work_raise() was added without a prototype in header
irq_work.h.
Fix the following warning (treated as error in W=1):
arch/powerpc/kernel/time.c:523:6: error: no previous prototype for ‘arch_irq_work_raise’
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit 55ccf3fe3f ("fork: move the real prepare_to_copy() users to
arch_dup_task_struct()") a new arch_dup_task_struct() was added
without a prototype declared in thread_info.h header. Fix the
following warning (treated as error in W=1):
arch/powerpc/kernel/process.c:1609:5: error: no previous prototype for ‘arch_dup_task_struct’
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The function time_init did not have a prototype defined in the time.h
header. Fix the following warning (treated as error in W=1):
arch/powerpc/kernel/time.c:1068:13: error: no previous prototype for ‘time_init’
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit dabe859ec6 ("powerpc: Give hypervisor decrementer interrupts
their own handler") an empty body function was added, but no prototype
was declared. Fix warning (treated as error in W=1):
arch/powerpc/kernel/time.c:629:6: error: no previous prototype for ‘hdec_interrupt’
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit f0f558b131 ("powerpc/mm: Preserve CFAR value on SLB miss caused
by access to bogus address"), the function slb_miss_bad_addr() was added
without a prototype. This commit adds it.
Fix a warning (treated as error in W=1):
arch/powerpc/kernel/traps.c:1498:6: error: no previous prototype for ‘slb_miss_bad_addr’
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
__giveup_fpu() is never called outside process.c, so it can be static.
That also means we don't need an empty definition in switch_to.h
Signed-off-by: Mathieu Malaterre <malat@debian.org>
[mpe: Also drop the empty version, rewrite change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Change signature of two functions, adding static keyword to prevent the
following two warnings (treated as errors on W=1):
arch/powerpc/platforms/embedded6xx/flipper-pic.c:135:28: error: no previous prototype for ‘flipper_pic_init’
arch/powerpc/platforms/embedded6xx/usbgecko_udbg.c:172:6: error: no previous prototype for ‘ug_udbg_putc’
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since the value of `tmp` is never intended to be read, declare both `tmp`
variables as unused. Fix warning (treated as error in W=1):
arch/powerpc/kernel/signal_32.c: In function ‘sys_swapcontext’:
arch/powerpc/kernel/signal_32.c:1048:16: error: variable ‘tmp’ set but not used
arch/powerpc/kernel/signal_32.c: In function ‘sys_debug_setcontext’:
arch/powerpc/kernel/signal_32.c🔢16: error: variable ‘tmp’ set but not used
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The inline keyword was not at the beginning of the function declaration.
Fix the following warning (treated as error in W=1):
arch/powerpc/lib/sstep.c:283:1: error: ‘inline’ is not at beginning of declaration
static int nokprobe_inline copy_mem_in(u8 *dest, unsigned long ea, int nb,
arch/powerpc/lib/sstep.c:388:1: error: ‘inline’ is not at beginning of declaration
static int nokprobe_inline copy_mem_out(u8 *dest, unsigned long ea, int nb,
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fix warning for all register unsigned long (0,3-12) that appear during W=1
compilation:
./arch/powerpc/include/asm/epapr_hcalls.h:479:2: warning: ‘register’ is not at beginning of declaration [-Wold-style-declaration]
unsigned long register r[\d] asm("r[\d]");
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On MCE the current code will restart the machine with
ppc_md.restart(). This case was extremely unlikely since
prior to that a skiboot call is made and that resulted in
a checkstop for analysis.
With newer skiboots, on P9 we don't checkstop the box by
default, instead we return back to the kernel to extract
useful information at the time of the MCE. While we still
get this information, this patch converts the restart to
a panic(), so that if configured a dump can be taken and
we can track and probably debug the potential issue causing
the MCE.
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
