A chapter is added to describe the trackpoint packets.
A section is added to describe the behaviour of the knob crc_enabled in
sysfs.
The introduction of the documentation only mentioned v1/v2, but in the
last part it already contains explanation of v3 and v4. The introduction
is updated.
Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The hw_version 3 Elantech touchpad on the Gigabyte U2442 does not accept
0x0b as initialization value for r10, this stand-alone version of the
driver: http://planet76.com/drivers/elantech/psmouse-elantech-v6.tar.bz2
Uses 0x03 which does work, so this means not setting bit 3 of r10 which
sets: "Enable Real H/W Resolution In Absolute mode"
Which will result in half the x and y resolution we get with that bit set,
so simply not setting it everywhere is not a solution. We've been unable to
find a way to identify touchpads where setting the bit will fail, so this
patch uses a dmi based blacklist for this.
https://bugzilla.kernel.org/show_bug.cgi?id=61151
Cc: stable@vger.kernel.org
Reported-by: Philipp Wolfer <ph.wolfer@gmail.com>
Tested-by: Philipp Wolfer <ph.wolfer@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
v4 hardware is a true multitouch capable touchpad (up to 5 fingers).
The packet format is quite complex, please see protocol document for
reference.
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
v3 hardware's packet format is almost identical to v2 (one/three finger touch),
except when sensing two finger touch, the hardware sends 12 bytes of data.
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Acked-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
For some Dell laptops, Ubuntu had a special version of the elantech
driver with more knowledge on the devices. It can be found there:
http://zinc.ubuntu.com/git?p=mid-team/hardy-netbook.git;a=blob;f=drivers/input/mouse/elantech.c;h=d0e2cafed162428f72e3654f4dda85e08ea486b3;hb=refs/heads/abi-22
By inspecting the source code, and doing some test on a real hardware, I
have completed the protocol specification (especially for the 6 bytes
protocol). It also adds information about the mapping between the
version reported by the device and the protocol to use.
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In older versions of the elantech hardware/firmware those bits always
were unset, so it didn't actually matter, but newer versions seem to
use those high bits for something else, screwing up the coordinates
we report to the input layer for those devices.
Signed-off-by: Florian Ragwitz <rafl@debian.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This is version 5 of the driver. Relative mode support has been
dropped (users wishing to use touchpad in relative mode can use
standard PS/2 protocol emulation done in hardware). The driver
supports both original version of Elantech protocol and the newer
one used by touchpads installed in EeePC.
Signed-off-by: Arjan Opmeer <arjan@opmeer.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
