Commit Graph

22991 Commits

Author SHA1 Message Date
Jonathan Woithe
7cf51e4831 [ALSA] hda: ALC260 test model implementation
Modules: HDA Codec driver

The following patch adds a 'test' ALC260 model specification to the
patch_realtek.c driver if CONFIG_SND_DEBUG is set.  This is similar to the
'test' ALC880 model in that it sets up mixer controls for almost everything
to make it easier for people to test their laptop/soundcard when working out
what pin widgets are connected to which real-world devices.

This patch assumes my previous patch (adding the second PCM to the ALC260)
has previously been applied since it uses infrastructure added by that
patch.

In developing this patch it was found that not all retasking pins accept all
the modes - in particular, some ignore the VREFxx variants.  The pin mode
control has therefore been tweaked to prevent this becoming a problem in
mixer applications.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-22 10:28:50 +01:00
Takashi Iwai
8b33a5aa08 [ALSA] hda: minor correction to fujitsu ALC260 initverbs
Modules: HDA Codec driver

Jonathan Woithe <jwoithe@physics.adelaide.edu.au>

The following patch changes the initverbs associated with the output sum
widgets 0x08, 0x09 and 0x0a used with the fujitsu model in patch_realtek.c.
It is against alsa 1.0.11rc3.

Currently these widgets have their output muted, but a close reading of the
datasheet suggests that they don't actually have an output mute.  They have
an *input* mute for each of their two inputs and a single output gain. This
patch therefore activates the input mutes and zeros the output gain.  It has
not yet been tested but the above interpretation of the ALC260 datasheet
seems correct.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-22 10:28:46 +01:00
Jonathan Woithe
4c5186ed6b [ALSA] hda: add PCM for 2nd ADC on ALC260
Modules: HDA Codec driver

The following patch against alsa 1.0.11rc3 creates a PCM device (pcm1c) for
the second ADC present on the ALC260 codec used by the hda driver.  It also
defines a new mixer control allowing the mode of retasking pins to be set;
this means a user can (for example) designate the headphone jack to be a
second input. With this patch in place it is possible to do 4 channel
recording on laptops equipped with an ALC260 codec assuming both a stereo
line-in jack is provided in addition to a headphone jack.

Mixer controls are provided to allow the headphone jack to be switched as
an input.  In addition, an (input only) mode control is configured for
the line-in jack to allow a bias voltage to be requested (VREF80 or VREF50)
so headsets based on condensor microphones have a chance of working.

This patch has been tested on a Fujitsu S7020 laptop and as such these
features are currently only configured for the 'fujitsu' model.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-22 10:28:42 +01:00
Charl Coetzee
ba22429d3e [ALSA] ac97 - Added a codec patch for LM4550
Modules: AC97 Codec

Added a codec patch for LM4550.  It sets up a static volume resolution
table.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-22 10:28:39 +01:00
Takashi Iwai
50dabc2d11 [ALSA] ac97 - Add support of static resolution tables
Modules: AC97 Codec

Added the support of static resolution table support for codecs
that the driver cannot probe the volume resolution properly.

The table pointer should be set in each codec patch.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-22 10:28:34 +01:00
Clemens Ladisch
b2b8229dde [ALSA] usb-audio: add Miditech Play'n Roll support
Modules: USB generic driver

Add a quirk entry for the Miditech Play'n Roll.

Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
2006-03-22 10:28:31 +01:00
Jaroslav Kysela
abf58f0955 [ALSA] bt848 - added Leadtek Winfast tv 2000xp delux to whitelist
Modules: BT87x driver

- added 0x107d:0x6606 to whitelist
- print also the pci device ID for developers when model is not known

Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2006-03-22 10:28:29 +01:00
Alan Horstmann
531af46279 [ALSA] ice1712 - disable unused ADCs & DACs on DMX6fire
Modules: ICE1712 driver

Change the value written to hardware configuration register of envy24 chip
in the case of Terratec DMX6fire to restrict the active ADCs & DACs to 6.

Also add the dxr_enable module option to eventually leave the old behaviour
when user requests.

Signed-off-by: Alan Horstmann <gineera@aspect135.co.uk>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2006-03-22 10:28:25 +01:00
Clemens Ladisch
cc7a59bd8d [ALSA] usb-audio: rename QUIRK_MIDI_MIDITECH to QUIRK_MIDI_CME
Modules: USB generic driver

Rename QUIRK_MIDI_MIDITECH to QUIRK_MIDI_CME because Miditech keyboards
are built by CME and use the same protocol, and don't force a Miditech
product name for the USB ID used by both Miditech and CME UF-x
keyboards.

Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
2006-03-22 10:28:22 +01:00
Jaroslav Kysela
e957ebf164 [ALSA] ice1712 & cs8427 - fix problem for S/PDIF input setup
Modules: I2C cs8427,ICE1712 driver

See ALSA bug#1785 for more details.

Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2006-03-22 10:28:15 +01:00
Takashi Iwai
2ba8c15c73 [ALSA] Removed unneeded page-reserve
Modules: Memalloc module

Removed unneeded page-reservation.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-22 10:28:12 +01:00
Takashi Iwai
ea50888d83 [ALSA] Use dma_alloc_coherent() hack on i386 only
Modules: Memalloc module

Use dma_alloc_coherent() hack on i386 only (as a valid arch).

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-22 10:28:06 +01:00
Takashi Iwai
c82590d2b2 [ALSA] Fix mulaw -> linear conversion in OSS PCM emulation
Modules: ALSA<-OSS emulation

Fixed the missing mulaw -> linear conversion in OSS PCM emulation code.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-22 10:28:02 +01:00
Takashi Iwai
d6ec894b6d [ALSA] Add the notes on PM to ens1370/ens1371 sections
Modules: Documentation

Add the notes on PM to ens1370/ens1371 sections.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-22 10:27:20 +01:00
Clemens Ladisch
119c4ff52e [ALSA] usb-audio: add UM-1EX/UM-2EX information
Modules: USB generic driver

Add comments with information about UM-1EX/UM-2EX devices.

Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
2006-03-22 10:27:14 +01:00
Clemens Ladisch
05422575d4 [ALSA] usb-audio: fix number of G-70 ports
Modules: USB generic driver

The G-70 has one MIDI port in each direction, no two.

Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
2006-03-22 10:27:10 +01:00
Jaroslav Kysela
3f72a30ccf [ALSA] snd_pcm_format_name() is no longer exported
Modules: PCM Midlevel,USB generic driver

Because snd_pcm_format_name() function is used only for informational
purposes, it is no longer exported from the PCM midlevel to reduce
space and dependency. usbaudio module shows only numeric value for format.

Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2006-03-22 10:27:05 +01:00
Clemens Ladisch
cdca881d79 [ALSA] usb-audio: add Roland G-70 support
Modules: USB generic driver

Add a quirk entry for the Roland G-70.

Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
2006-03-22 10:26:24 +01:00
Jaroslav Kysela
5a25c5cfd4 [ALSA] ymfpci - make rear channel swap optional
Modules: YMFPCI driver

Added rear_swap module option / kernel parameter to configure the rear
channel swapping. Default value is enable to make the AC3 passthrough
working, but analog only users might revert the previous behaviour.

Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2006-03-22 10:26:21 +01:00
Ingo Molnar
12aa757905 [ALSA] semaphore -> mutex (Archs, misc buses)
Semaphore to mutex conversion.

The conversion was generated via scripts, and the result was validated
automatically via a script as well.

Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-22 10:25:43 +01:00
Ingo Molnar
62932df8fb [ALSA] semaphore -> mutex (PCI part)
Semaphore to mutex conversion.

The conversion was generated via scripts, and the result was validated
automatically via a script as well.

Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-22 10:25:29 +01:00
Ingo Molnar
8b7547f95c [ALSA] semaphore -> mutex (ISA part)
Semaphore to mutex conversion.

The conversion was generated via scripts, and the result was validated
automatically via a script as well.

Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-22 10:25:03 +01:00
Ingo Molnar
ef9f0a42db [ALSA] semaphore -> mutex (driver part)
Semaphore to mutex conversion.

The conversion was generated via scripts, and the result was validated
automatically via a script as well.

Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-22 10:24:57 +01:00
Ingo Molnar
1a60d4c5a0 [ALSA] semaphore -> mutex (core part)
Semaphore to mutex conversion.

The conversion was generated via scripts, and the result was validated
automatically via a script as well.

Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-22 10:24:50 +01:00
Takashi Iwai
f0283f45a0 [ALSA] au88x0 - Fix structs for equalizer
Modules: au88x0 driver

Fixed the structures for equalizer.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-22 10:24:35 +01:00
Mark Salazar
95b712965f [ALSA] #4/4 for Zoom Video - add Zoom Video support
Modules: ES18xx driver

Forth of 4 es18xx.c patches culminating in Zoom Video support.

This patch adds Zoom Video support for those chipsets that support it.

Testing:
This work was initially done on the source from the Debian Sarge ALSA
package, then tested
on an ES1879. I could not test the Zoom Video function for an ES1878 or
ES1869.
Patches were created against the Sarge code and then edited to apply
correctly to the
ALSA cvs code. Lastly the patched ALSA cvs code was test for successful
compilation.
No additional testing was done on the ALSA cvs version.

One quirk (noted in my comments below) is that apparently the datasheet
is wrong
for one of the ES1879 Zoom Video 'enable' bits, because
 1) if you set this bit it messes up PCM playback (speaker_test play a
lower frequency)
 2) even if you don't set this bit Zoom Video still works.
I added a control to toggle the bit on just in case there might be a
version of the
ES1879 that requires it, but I expect noone will need it.

Signed-off-by: Mark Salazar <markTheCoder@justmyself.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-22 10:24:17 +01:00
Mark Salazar
14086771c0 [ALSA] #3/4 for Zoom Video - change Hardware Volume interrupt handling
Modules: ES18xx driver

Third of 4 es18xx.c patches culminating in Zoom Video support.

This patch changes the Hardware Volume support to reflect the fact that
not all of the
supported chipsets have seperate registers dedicated to the Hardware
Volume inputs. Although
all the chipsets can generate an HWV interrupt whenever a Hardware
Volume input is received
only those with seperate HWV registers can split the HWV registers from
the Master volume
registers.

Testing:
This work was initially done on the source from the Debian Sarge ALSA
package, then tested
on an ES1879 and an ES1878 machine. Patches were created against the
Sarge code and then edited
to apply correctly to the ALSA cvs code. Lastly the patched ALSA cvs
code was test for
successful compilation. No additional testing was done on the ALSA cvs
version.

Signed-off-by: Mark Salazar <markTheCoder@justmyself.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-22 10:24:08 +01:00
Mark Salazar
f4df221f8f [ALSA] #2/4 for Zoom Video - resolve number of record sources
Modules: ES18xx driver

Second of 4 es18xx.c patches culminating in Zoom Video support.

This patch changes the 'record source' mux routines to reflect the fact
that not all of the
supported chipsets have 8 possible inputs. Some have 4 and some have 5.

Testing:
This work was initially done on the source from the Debian Sarge ALSA
package, then tested
on an ES1879 and an ES1878 machine. Patches were created against the
Sarge code and then edited
to apply correctly to the ALSA cvs code. Lastly the patched ALSA cvs
code was test for
successful compilation. No additional testing was done on the ALSA cvs
version.

Signed-off-by: Mark Salazar <markTheCoder@justmyself.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-22 10:24:04 +01:00
Mark Salazar
c1f6d41593 [ALSA] #1/4 for Zoom Video - resolve common vs chipset specific mixer controls
Modules: ES18xx driver

First of 4 es18xx.c patches culminating in Zoom Video support.
While adding support for Zoom Video to the es18xx driver I found some of
the mixer controls
were wrong. Since you guys went to the trouble of supplying the
datasheets for the supported
chipsets I did a review of all of them and tried to get es18xx.c to
accurately reflect the
proper mixer controls for each chipset. If the datasheets are wrong then
so are my patches.

This first patch moves some controls from the common-to-all-chipsets array
'snd_es18xx_base_controls' to a chipset-specific array and adds code to
manage that new array.
Also while testing on my ES1878 test machine I discovered it needed a
couple of udelays in
the identify function so those are in this patch as well.

Testing:
This work was initially done on the source from the Debian Sarge ALSA
package, then tested
on an ES1879 and an ES1878 machine. Patches were created against the
Sarge code and then edited
to apply correctly to the ALSA cvs code. Lastly the patched ALSA cvs
code was test for
successful compilation. No additional testing was done on the ALSA cvs
version.

Signed-off-by: Mark Salazar <markTheCoder@justmyself.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-22 10:23:52 +01:00
Clemens Ladisch
415b09e455 [ALSA] usb-audio: add Edirol PC-50 support
Modules: USB generic driver

Add a quirk entry for the Edirol PC-50.

Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
2006-03-22 10:23:47 +01:00
Takashi Iwai
f7cbb7fcd3 [ALSA] Fix snd_xxx_t typedefs
Modules: PXA Mainstone driver,CX88 driver,SAA7134 driver

Replace snd_xxx_t typedefs with explicit structs.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-22 10:23:39 +01:00
Takashi Iwai
97c67b65cb [ALSA] au88x0 - 64bit arch fixes
Modules: au88x0 driver

Fix the driver codes to run on 64bit architectures.
The patch taken from ALSA BTS bug#1047.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-22 10:23:32 +01:00
Takashi Iwai
7a6c8ff1ef [ALSA] Update description of ice1724 driver
Modules: Documentation

Updated the description of ice1724 driver.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-22 10:23:27 +01:00
Takashi Iwai
45fe722ba8 [ALSA] ice1724 - Add support of Prodigy-7.1LT
Modules: ICE1712 driver

Added the support of Prodigy-7.1LT board.
The patch taken from ALSA BTS bug#1090.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-22 10:23:23 +01:00
Takashi Iwai
0534ab4279 [ALSA] Clean up pcm-oss plugins
Modules: ALSA<-OSS emulation

Clean up pcm-oss plugin codes.
Removed dead codes, and simplified route/rate plugins.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-22 10:23:20 +01:00
Takashi Iwai
9d83911ac0 [ALSA] Fix a typo
Modules: ALSA<-OSS emulation

Fixed a typo.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-22 10:23:16 +01:00
Jaroslav Kysela
21a3479a0b [ALSA] PCM midlevel & PCM OSS - make procfs & OSS plugin code optional
Modules: ALSA Core,PCM Midlevel,ALSA<-OSS emulation,USB generic driver

1) The verbose procfs code for the PCM midlevel and usb audio
   can be removed now (more patches will follow).
   CONFIG_SND_VERBOSE_PROCFS
2) The PCM OSS plugin system can be also compiled optionaly.
   CONFIG_SND_PCM_OSS_PLUGINS

Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2006-03-22 10:23:12 +01:00
Clemens Ladisch
153abaa4ff [ALSA] ymfpci: fix swapped channels in SPDIF output
Modules: YMFPCI driver

The routing of the effect 2/3 channels to the digital output is the
opposite of the rear analog output (left/right swapped).

We make the order correct for the digital output (which will make the
analog rear have the channels swapped) to make AC3 output work.

Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
2006-03-22 10:23:00 +01:00
Takashi Iwai
27346166a9 [ALSA] hda-intel - Add single_cmd option for debugging
Modules: Documentation,HDA Intel driver

Added single_cmd module option for debugging in the case CORB/RIRB
doesn't work well (e.g. due to wrong irq routings).

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-22 10:22:51 +01:00
Takashi Iwai
84a43bd523 [ALSA] intel8x0 - Fix/cleanup detection of codecs on SIS7012
Modules: Intel8x0 driver

Fix the detection of tertriary codec on SIS7012, including clean-ups
of relevant codes.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-22 10:22:46 +01:00
Takashi Iwai
15f500a699 [ALSA] ens1370 - Fix resume
Modules: ENS1370/1+ driver

Fix resume of ens1370 driver.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-22 10:22:42 +01:00
Clemens Ladisch
9568f461e5 [ALSA] usb-audio: factor out packet size calculation code
Modules: USB generic driver

Move the common packet size calculation code from
prepare_startup_playback_urb() and prepare_playback_urb() to a new
function.

Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
2006-03-22 10:22:27 +01:00
Clemens Ladisch
7c79b7682e [ALSA] usb-audio: cosmetic changes
Modules: USB generic driver

Move some entries around to keep them sorted by ID.

Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
2006-03-22 10:22:22 +01:00
Brent Cook
e03173fce2 [ALSA] Add support for EDIROL UM-3ex
Modules: USB generic driver

This is my naive attempt at adding ALSA device support. The attached
patch provides support for the EDIROL UM-3ex. This is a 3-port USB midi
interface with a built-in USB hub and the ability to chain 2 other
UM-3x's in a master-slave configuration. I only have one, so I do not
know how this works in practice.

Though this is a 3-port device, I had to throw in that 4th 'Control' interface
to the definition in order to make the 3rd port work. If I set in/out_cables
to 0x000b, a 3rd interface appears on the driver, but it does nothing.
Changing it to 0x000f allows the 3rd interface to work, but of course
interface 4 does not work because it does not exist.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-22 10:22:14 +01:00
Takashi Iwai
34226c4239 [ALSA] pcxhr - Suppress debug messages
Modules: Digigram PCXHR driver

Suppress debug messages.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2006-03-22 10:21:58 +01:00
David S. Miller
dcc1e8dd88 [SPARC64]: Add a secondary TSB for hugepage mappings.
Signed-off-by: David S. Miller <davem@davemloft.net>
2006-03-22 01:15:14 -08:00
David S. Miller
14778d9072 [SPARC]: Respect vm_page_prot in io_remap_page_range().
Make sure the callers do a pgprot_noncached() on
vma->vm_page_prot.

Pointed out by Hugh Dickens.

Signed-off-by: David S. Miller <davem@davemloft.net>
2006-03-22 01:15:13 -08:00
David S. Miller
056755f4d7 [TG3]: Bump driver version and reldate.
Signed-off-by: David S. Miller <davem@davemloft.net>
2006-03-22 01:07:53 -08:00
Michael Chan
15c3b69610 [TG3]: Skip phy power down on some devices
Some PHYs should not be powered down in tg3_set_power_state() because
of bugs or other hardware limitations.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2006-03-22 01:06:52 -08:00
Michael Chan
caf636c760 [TG3]: Fix SRAM access during tg3_init_one()
5700 and 5701 will not return correct SRAM data when the chip is in
D3hot power state. tg3_get_eeprom_hw_cfg() must first put the device
in D0 before reading SRAM.

Thanks to Thomas Chenault at Dell for noticing this problem.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2006-03-22 01:05:31 -08:00