ICL has two slices of DBuf, each slice of size 1024 blocks.
We should not always enable slice-2. It should be enabled only if
display total required BW is > 12GBps OR more than 1 pipes are enabled.
Changes since V1:
- typecast total_data_rate to u64 before multiplication to solve any
possible overflow (Rodrigo)
- fix where skl_wm_get_hw_state was memsetting ddb, resulting
enabled_slices to become zero
- Fix the logic of calculating ddb_size
Changes since V2:
- If no-crtc is part of commit required_slices will have value "0",
don't try to disable DBuf slice.
Changes since V3:
- Create a generic helper to enable/disable slice
- don't return early if total_data_rate is 0, it may be cursor only
commit, or atomic modeset without any plane.
Changes since V4:
- Solve checkpatch warnings
- use kernel types u8/u64 instead of uint8_t/uint64_t
Changes since V5:
- Rebase
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180426142517.16643-3-mahesh1.kumar@intel.com
This patch adds support to start tracking status of DBUF slices.
This is foundation to introduce support for enabling/disabling second
DBUF slice dynamically for ICL.
Changes Since V1:
- use kernel type u8 over uint8_t
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180426142517.16643-2-mahesh1.kumar@intel.com
These fields have been deprecated and moved in ICL+. Stop setting the
bits.
They have moved to GAMMA_MODE and CSC_MODE, respectively. This patch
is just to stop incorrectly setting bits in PLANE_COLOR_CTL while
we're waiting for the new replacement functionality to be done.
v2: Drop useless comment, and change !(GEN >= 11) to (GEN < 11). (Ville)
v3: No changes
v4 (from Paulo): Rebase.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180328215803.13835-2-paulo.r.zanoni@intel.com
As the Geminilake firmware is now merged to linux-firmware.git
use MODUE_FIRMWARE to load the firmware.
This removes the error message in the dmesg log:
i915 0000:00:02.0: Direct firmware load for
i915/glk_dmc_ver1_04.bin failed with error -2
i915 0000:00:02.0: Failed to load DMC firmware
i915/glk_dmc_ver1_04.bin. Disabling runtime power management.
i915 0000:00:02.0: DMC firmware homepage:
https://01.org/linuxgraphics/downloads/firmware
and now shows that the firmware has correctly loaded:
[drm] Finished loading DMC firmware i915/glk_dmc_ver1_04.bin (v1.4)
Signed-off-by: Ian W MORRISON <ianwmorrison@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180411044213.383-1-ianwmorrison@gmail.com
- Fix for black screen issues (FDO #104158 and #104425)
- A correction for wrongly applied display W/A
- Fixes for HDA codec interop issue (no audio) and too eager HW timeouts
* tag 'drm-intel-fixes-2018-04-26' of git://anongit.freedesktop.org/drm/drm-intel:
drm/i915/fbdev: Enable late fbdev initial configuration
drm/i915: Use ktime on wait_for
drm/i915: Enable display WA#1183 from its correct spot
drm/i915/audio: set minimum CD clock to twice the BCLK
This was my bad, spec says that the name of this bit is
'Y-coordinate valid' but the values for it is:
0: Include Y-coordinate valid eDP1.4a
1: Do not include Y-coordinate valid eDP 1.4
So not setting it.
BSpec: 7713
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180425212334.21109-4-jose.souza@intel.com
IGT tests could be improved with sink status, knowing for sure that
hardware have activate or exit PSR.
v3:
Reading i915_edp_psr_status was causing PSR to exit but now with
'drm/i915/psr: Prevent PSR exit when a non-pipe related register is
written' it is fixed.
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180425212334.21109-3-jose.souza@intel.com
This will be helpful to debug what hardware is actually tracking
and causing PSR to exit.
BSpec: 7721
v4:
- Using _MMIO_TRANS2() in PSR_EVENT
- Cleaning events before printing
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180425212334.21109-2-jose.souza@intel.com
Any write in any display register was causing HW to exit PSR,
masking it to allow more power savings. Writes to pipe related
registers will still cause HW to exit PSR.
This is already masked for PSR2.
It also do not break the Display WA #0884, writes to CURSURFLIVE
are still causing hardware to exit PSR. This was tested in CNL machine
by triggering a write to CURSURFLIVE when a debugfs was read by user.
Bspec: 7721 and 8042
v4: Checked that it do not breaks WA #0884 and added this information
to the commit message.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180425212334.21109-1-jose.souza@intel.com
Even though we weren't injecting guilty requests to be reset, we could
still fall over the issue of resetting the same request too fast -- where
the GPU refuses to start again. (Although it is interesting to note that
reloading the driver is sufficient, suggesting that we could recover if
we delayed the setup after reset?) Continue to paper over the problem by
adding a small delay by waiting for the engine to idle between tests,
and ensure that the engines are idle before starting the idle tests.
v2: Replace single instance of 50 with a magic macro.
References: 028666793a ("drm/i915/selftests: Avoid repeatedly harming the same innocent context")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180411120346.27618-1-chris@chris-wilson.co.uk
For now, there's just the one link config selection, optimizing for slow
and wide link. No functional changes.
Keep the debug logging in the caller, to avoid duplication later on if
alternative link confing selection gets added.
v2: Improved commit message
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/64848b76bf90d6ceecd7ec6b5add28531e0b1a41.1524730974.git.jani.nikula@intel.com
We call intel_dp_compute_rate() in intel_dp_compute_config() only to be
able to debug log the link_bw and rate_select parameters; we don't use
the parameters here for anything else. We call intel_dp_compute_rate()
again during link training where we actually need and use the
parameters.
Move the debug logging of link_bw and rate_select to
intel_dp_link_training_clock_recovery(), and clean up the extra
intel_dp_compute_rate() call and extra clutter from the already
overcrowded intel_dp_compute_config().
v2: Rewrote commit message (Rodrigo, Manasi)
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/c5cf6a179e2d244eceb6bb80a792765d9efbee4f.1524730974.git.jani.nikula@intel.com
The majority of the engine state dumping is too voluminous to be useful
outside of a controlled setup, though a few do accompany severe errors.
Keep the debug dumps next to the errors, but hide the others behind a CI
compile flag. This becomes more useful when adding more dumps to latency
sensitive paths.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180426103219.22181-1-chris@chris-wilson.co.uk
We can convert engine stats from a spinlock to seqlock to ensure interrupt
processing is never even a tiny bit delayed by parallel readers.
There is a smidgen bit more cost on the write lock side, and an extremely
unlikely chance that readers will have to retry a few times in face of
heavy interrupt load. But it should be extremely unlikely given how
lightweight read side section is compared to the interrupt processing
side, and also compared to the rest of the code paths which can lead into
it. Furthermore, writer is the ones doing the real, latency sensitive
work, while readers are only informative.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180426074716.7352-1-tvrtko.ursulin@linux.intel.com
The "adjusted_mode" clock value (ie the real pixel clock) is more
accurate than "mode" clock value (ie the panel/bridge requested
clock value). It offers a better preciseness for timing
computations and allows to reduce the extra dsi bandwidth in
burst mode (from ~20% to ~10-12%, hw platform dependent).
Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Tested-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Yannick Fertré <yannick.fertre@st.com>
Tested-by: Yannick Fertré <yannick.fertre@st.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180125155504.8611-1-philippe.cornu@st.com
qxl: 2 bug fixes (Gerd)
core: Don't use stale display info between HDMI hotplugs (Ville)
virtio: Fix guest spinning when request queue is full (Gerd)
Cc: Ondrej Jirman <megous@megous.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEfxcpfMSgdnQMs+QqlvcN/ahKBwoFAlrg2McACgkQlvcN/ahK
Bwp+Mwf+JyzD7ppH2jycUcvhs3Bu1NGShzDizinxwbZQvEXMwhHJ9F9yYEIGbLEI
GHmpZhRMPWEV7pBMXe1A53AsJ1TrmeAnNeEMjRUjTH2OEb9IWqo4tPM2UvrvI30n
zmoI/4h8gcsgUgQFX6NqKRxMX93NdcNc/Hp2IP/b3mFKlryeXnNNfMP7DtQAwysw
Fm6qQETbVa3osZ9Lqn8Yh3OorUpCJK7mjBPUD1j2xngaYQMnDyT9A2oDqmOzoNov
cXPrd423Iwr70YcEeapcWobxlTf4ge5fNNwpQ4a4ezXkWzVUeBFmt/7TuhdcbR23
biEysZQaG0nbdtWuL2KWV5SEE3tzyA==
=ZviK
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-fixes-2018-04-25' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
sun41: Fix regression for TBSA711 tablet (Ondrej)
qxl: 2 bug fixes (Gerd)
core: Don't use stale display info between HDMI hotplugs (Ville)
virtio: Fix guest spinning when request queue is full (Gerd)
Cc: Ondrej Jirman <megous@megous.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
* tag 'drm-misc-fixes-2018-04-25' of git://anongit.freedesktop.org/drm/drm-misc:
drm/edid: Reset more of the display info
drm/virtio: fix vq wait_event condition
qxl: keep separate release_bo pointer
qxl: fix qxl_release_{map,unmap}
Revert "drm/sun4i: add lvds mode_valid function"
A few fixes for 4.17.. thanks to Sean for helping pull together some
of the display related fixes while I was off in compute-land.
* tag 'drm-msm-fixes-2018-04-25' of git://people.freedesktop.org/~robclark/linux:
drm/msm: don't deref error pointer in the msm_fbdev_create error path
drm/msm/dsi: use correct enum in dsi_get_cmd_fmt
drm/msm: Fix possible null dereference on failure of get_pages()
drm/msm: Add modifier to mdp_get_format arguments
drm/msm: Mark the crtc->state->event consumed
drm/msm/dsi: implement auto PHY timing calculator for 10nm PHY
drm/msm/dsi: check video mode engine status before waiting
drm/msm/dsi: check return value for video done waits
- Fix a hang on CZ boards with EDC enabled
- Fix hangs related to DP MST handling
- Fix a deadlock in irq handling in DC
* 'drm-fixes-4.17' of git://people.freedesktop.org/~agd5f/linux:
drm/amd/display: Check dc_sink every time in MST hotplug
drm/amd/display: Update MST edid property every time
drm/amd/display: Don't read EDID in atomic_check
drm/amd/display: Disallow enabling CRTC without primary plane with FB
drm/amd/display: Fix deadlock when flushing irq
drm/amdgpu: set COMPUTE_PGM_RSRC1 for SGPR/VGPR clearing shaders
We're currently failing to reset everything in display_info.hdmi
which will potentially cause us to use stale information when
swapping monitors. Eg. if the user replaces a HDMI 2.0 monitor
with a HDMI 1.x monitor we will continue to think that the monitor
supports scrambling. That will lead to a black screen since the
HDMI 1.x monitor won't understand the scrambled signal.
Fix the problem by clearing display_info.hdmi fully. And while at
eliminate some duplicated code by calling drm_reset_display_info()
in drm_add_display_info().
Cc: stable@vger.kernel.org
Cc: Antony Chen <antonychen@qnap.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105655
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180424130250.7028-1-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Antony Chen <antonychen@qnap.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Wait until we have enough space in the virt queue to actually queue up
our request. Avoids the guest spinning in case we have a non-zero
amount of free entries but not enough for the request.
Cc: stable@vger.kernel.org
Reported-by: Alain Magloire <amagloire@blackberry.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20180403095904.11152-1-kraxel@redhat.com
Signed-off-by: Sean Paul <seanpaul@chromium.org>
qxl expects that list_first_entry(release->bos) returns the first
element qxl added to the list. ttm_eu_reserve_buffers() may reorder
the list though.
Add a release_bo field to struct qxl_release and use that instead.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20180418054257.15388-3-kraxel@redhat.com
Signed-off-by: Sean Paul <seanpaul@chromium.org>
s/PAGE_SIZE/PAGE_MASK/
Luckily release_offset is never larger than PAGE_SIZE, so the bug has no
bad side effects and managed to stay unnoticed for years that way ...
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20180418054257.15388-2-kraxel@redhat.com
Signed-off-by: Sean Paul <seanpaul@chromium.org>
The reverted commit broke LVDS output on TBS A711 Tablet. That tablet
has simple-panel node that has fixed pixel clock-frequency that A83T
SoC used in the tablet can't generate exactly.
Requested rate is 52000000 and rounded_rate is calculated as 51857142.
It's close enough for it to work in practice, but with strict check
in the reverted commit, the mode is rejected needlessly in this case.
DT allows to specify a range of values for simple-panel/clock-frequency,
but driver doesn't respect that ATM. Given that TBS A711 is the single
user of sun4i-lvds driver, let's revert that commit for now, until
a better solution for the problem is found.
Also see: https://patchwork.kernel.org/patch/9446385/ for relevant
discussion (or search for "[RFC] drm/sun4i: rgb: Add 5% tolerance
to dot clock frequency check").
Fixes: e4e4b7ad50 ("drm/sun4i: add lvds mode_valid function")
Reported-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180421045155.15332-1-megous@megous.com
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Interrupt handling in Gen11 is quite different from previous platforms.
v2: Rebased (Michel)
v3: Rebased with wiggle
v4: Rebased, remove TODO warning correctly (Daniele)
v5: Rebased, made gen11_gtiir const while at it (Michel)
v6: Rebased
v7: Adapt to the style currently in upstream
Suggested-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1524605995-22324-1-git-send-email-oscar.mateo@intel.com
Extended fix to: "Don't read EDID in atomic_check"
Fix issue of missing dc_sink in .mode_valid in hot plug routine.
Need to check dc_sink everytime in .get_modes hook after checking
edid, since edid is not getting removed in hot unplug but dc_sink
doesn't.
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Extended fix to: "Don't read EDID in atomic_check"
Fix display property not observed in GUI display after hot plug.
Call drm_mode_connector_update_edid_property every time in
.get_modes hook, due to the fact that edid property is getting
removed from usermode ioctl DRM_IOCTL_MODE_GETCONNECTOR each time
in hot unplug.
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
We shouldn't attempt to read EDID in atomic_check. We really shouldn't
even be modifying the connector object, or any other non-state object,
but this is a start at least.
Moving EDID cleanup to dm_dp_mst_connector_destroy from
dm_dp_destroy_mst_connector to ensure the EDID is still available for
headless mode.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The below commit
"drm/atomic: Try to preserve the crtc enabled state in drm_atomic_remove_fb, v2"
introduces a slight behavioral change to rmfb. Instead of disabling a crtc
when the primary plane is disabled, it now preserves it.
Since DC is currently not equipped to handle this we need to fail such
a commit, otherwise we might see a corrupted screen.
This is based on Shirish's previous approach but avoids adding all
planes to the new atomic state which leads to a full update in DC for
any commit, and is not what we intend.
Theoretically DM should be able to deal with states with fully populated planes,
even for simple updates, such as cursor updates. This should still be
addressed in the future.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Tested-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Lock irq table when reading a work in queue,
unlock to flush the work, lock again till all tasks
are cleared
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
When filling the ring to align the emit pointer to the next cacheline,
use memset64() rather than open-coding it. As we know that we always
have an even number of dwords, we can replace the dword loop with the
qword equivalent.
v2: s/0/MI_NOOP<<32 | MI_NOOP/
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180425123718.16366-1-chris@chris-wilson.co.uk
The method struct drm_connector_helper_funcs::mode_valid is defined
as returning an 'enum drm_mode_status' but the driver implementation
for this method uses an 'int' for it.
Fix this by using 'enum drm_mode_status' in the driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180424131522.2460-1-luc.vanoostenryck@gmail.com
The method struct drm_connector_helper_funcs::mode_valid is defined
as returning an 'enum drm_mode_status' but the driver implementation
for this method uses an 'int' for it.
Fix this by using 'enum drm_mode_status' in the driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180424131515.2360-1-luc.vanoostenryck@gmail.com
The method struct drm_connector_helper_funcs::mode_valid is defined
as returning an 'enum drm_mode_status' but the driver implementation
for this method, psb_intel_lvds_mode_valid(), uses an 'int' for it.
Fix this by using 'enum drm_mode_status' for psb_intel_lvds_mode_valid().
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180424131458.2060-1-luc.vanoostenryck@gmail.com
The method struct drm_connector_helper_funcs::mode_valid is defined
as returning an 'enum drm_mode_status' but the driver implementation
for this method uses an 'int' for it.
Fix this by using 'enum drm_mode_status' in the driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180424131455.2011-1-luc.vanoostenryck@gmail.com
The method struct drm_connector_helper_funcs::mode_valid is defined
as returning an 'enum drm_mode_status' but the driver implementation
for this method uses an 'int' for it.
Fix this by using 'enum drm_mode_status' in the driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180424131453.1961-1-luc.vanoostenryck@gmail.com
The method struct drm_connector_helper_funcs::mode_valid is defined
as returning an 'enum drm_mode_status' but the driver implementation
for this method uses an 'int' for it.
Fix this by using 'enum drm_mode_status' in the driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180424131445.1861-1-luc.vanoostenryck@gmail.com
The method struct drm_connector_helper_funcs::mode_valid is defined
as returning an 'enum drm_mode_status' but the driver implementation
for this method uses an 'int' for it.
Fix this by using 'enum drm_mode_status' in the driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180424131520.2409-1-luc.vanoostenryck@gmail.com
The method struct drm_connector_helper_funcs::mode_valid is defined
as returning an 'enum drm_mode_status' but the driver implementation
for this method uses an 'int' for it.
Fix this by using 'enum drm_mode_status' in the driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180424131508.2210-1-luc.vanoostenryck@gmail.com
The method struct drm_connector_helper_funcs::mode_valid is defined
as returning an 'enum drm_mode_status' but the driver implementation
for this method uses an 'int' for it.
Fix this by using 'enum drm_mode_status' in the driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180424131504.2159-1-luc.vanoostenryck@gmail.com
The method struct drm_connector_helper_funcs::mode_valid is defined
as returning an 'enum drm_mode_status' but the driver implementation
for this method uses an 'int' for it.
Fix this by using 'enum drm_mode_status' in the driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180424131450.1910-1-luc.vanoostenryck@gmail.com
The method struct drm_connector_helper_funcs::mode_valid is defined
as returning an 'enum drm_mode_status' but the driver implementation
for this method uses an 'int' for it.
Fix this by using 'enum drm_mode_status' in the driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180424131443.1810-1-luc.vanoostenryck@gmail.com
If the initial fbdev configuration (intel_fbdev_initial_config()) runs
and there still no sink connected it will cause
drm_fb_helper_initial_config() to return 0 as no error happened (but
internally the return is -EAGAIN). Because no framebuffer was
allocated, when a sink is connected intel_fbdev_output_poll_changed()
will not execute drm_fb_helper_hotplug_event() that would trigger
another try to do the initial fbdev configuration.
So here allowing drm_fb_helper_hotplug_event() to be executed when there
is no framebuffer allocated and fbdev was not set up yet.
This issue also happens when a MST DP sink is connected since boot, as
the MST topology is discovered in parallel if
intel_fbdev_initial_config() is executed before the first sink MST is
discovered it will cause this same issue.
This is a follow-up patch of
https://patchwork.freedesktop.org/patch/196089/
Changes from v1:
- not creating a dump framebuffer anymore, instead just allowing
drm_fb_helper_hotplug_event() to execute when fbdev is not setup yet.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104158
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104425
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: stable@vger.kernel.org # v4.15+
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: frederik <frederik.schwan@linux.com> # 4.15.17
Tested-by: Ian Pilcher <arequipeno@gmail.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180418234158.9388-1-jose.souza@intel.com
(cherry picked from commit df9e652174)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
We use jiffies to determine when wait expires. However
Imre did find out that jiffies can and will do a >1
increments on certain situations [1]. When this happens
in a wait_for loop, we return timeout errorneously
much earlier than what the real wallclock would say.
We can't afford our waits to timeout prematurely.
Discard jiffies and change to ktime to detect timeouts.
v2: added bugzilla entry (Imre), added stable (Chris)
Reported-by: Imre Deak <imre.deak@intel.com>
References: https://lkml.org/lkml/2018/4/18/798 [1]
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105771
Cc: Imre Deak <imre.deak@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423113754.28424-1-mika.kuoppala@linux.intel.com
(cherry picked from commit 3085982c6b)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
The ADV7511 has four 256-byte maps that can be accessed via the main I2C
ports. Each map has it own I2C address and acts as a standard slave
device on the I2C bus.
Allow a device tree node to override the default addresses so that
address conflicts with other devices on the same bus may be resolved at
the board description level.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1518544137-2742-6-git-send-email-kbingham@kernel.org
Otherwise, the SQ may skip some of the register writes, or shader waves may
be allocated where we don't expect them, so that as a result we don't actually
reset all of the register SRAMs. This can lead to spurious ECC errors later on
if a shader uses an uninitialized register.
Signed-off-by: Nicolai Hähnle <nicolai.haehnle@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Does what it says on the label, it's a little confusing debugging atomic
check failures otherwise.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180411234302.2896-2-lyude@redhat.com
Instead of synchronously cancelling the timer and re-enabling it inside
the reset callbacks, keep the timer enabled and let it die on its next
wakeup if no longer required. This allows
intel_engine_reset_breadcrumbs() to be used from an atomic
(timer/softirq) context such as required for resetting an engine.
It also allows us to react better to the user poking around debugfs for
testing missed irqs.
v2: Tighten the order of del_timer_sync as the fake_irq timer
may trigger the hangcheck timer, and so we should cancel it first and
then cancel the hangcheck (Mika)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180424142945.6787-1-chris@chris-wilson.co.uk
There is a potential execution path in which variable err is
returned without being properly initialized previously.
Fix this by initializing variable err to 0.
Addresses-Coverity-ID: 1468362 ("Uninitialized scalar variable")
Fixes: f4ecfbfc32 ("drm/i915: Check whitelist registers across resets")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180424131545.GA4053@embeddedor.com
If the initial fbdev configuration (intel_fbdev_initial_config()) runs
and there still no sink connected it will cause
drm_fb_helper_initial_config() to return 0 as no error happened (but
internally the return is -EAGAIN). Because no framebuffer was
allocated, when a sink is connected intel_fbdev_output_poll_changed()
will not execute drm_fb_helper_hotplug_event() that would trigger
another try to do the initial fbdev configuration.
So here allowing drm_fb_helper_hotplug_event() to be executed when there
is no framebuffer allocated and fbdev was not set up yet.
This issue also happens when a MST DP sink is connected since boot, as
the MST topology is discovered in parallel if
intel_fbdev_initial_config() is executed before the first sink MST is
discovered it will cause this same issue.
This is a follow-up patch of
https://patchwork.freedesktop.org/patch/196089/
Changes from v1:
- not creating a dump framebuffer anymore, instead just allowing
drm_fb_helper_hotplug_event() to execute when fbdev is not setup yet.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104158
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104425
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: stable@vger.kernel.org # v4.15+
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: frederik <frederik.schwan@linux.com> # 4.15.17
Tested-by: Ian Pilcher <arequipeno@gmail.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180418234158.9388-1-jose.souza@intel.com
If we have more than a few, possibly several thousand request in the
queue, don't show the central portion, just the first few and the last
being executed and/or queued. The first few should be enough to help
identify a problem in execution, and most often comparing the first/last
in the queue is enough to identify problems in the scheduling.
We may need some fine tuning to set MAX_REQUESTS_TO_SHOW for common
debug scenarios, but for the moment if we can avoiding spending more
than a few seconds dumping the GPU state that will avoid a nasty
livelock (where hangcheck spends so long dumping the state, it fires
again and starts to dump the state again in parallel, ad infinitum).
v2: Remember to print last not the stale rq iter after the loop.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180424081600.27544-1-chris@chris-wilson.co.uk
printk unhelpfully inserts a '\n' between consecutive calls, and since
our drm_printf wrapper may be emitting info a seq_file instead,
KERN_CONT is not an option. To work with any drm_printf destination, we
need to build up the output into a temporary buf on the stack and then
feed the complete line in a single call to printk.
Fixes: b7268c5eed ("drm/i915: Pack params to engine->schedule() into a struct")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180424010839.22860-1-chris@chris-wilson.co.uk
We need to be careful to not let compiler evaluate
the expiration and the operation on it's terms.
Document and enforce that COND will be evaluated
before checking timeout expiration.
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423113754.28424-2-mika.kuoppala@linux.intel.com
We use jiffies to determine when wait expires. However
Imre did find out that jiffies can and will do a >1
increments on certain situations [1]. When this happens
in a wait_for loop, we return timeout errorneously
much earlier than what the real wallclock would say.
We can't afford our waits to timeout prematurely.
Discard jiffies and change to ktime to detect timeouts.
v2: added bugzilla entry (Imre), added stable (Chris)
Reported-by: Imre Deak <imre.deak@intel.com>
References: https://lkml.org/lkml/2018/4/18/798 [1]
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105771
Cc: Imre Deak <imre.deak@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423113754.28424-1-mika.kuoppala@linux.intel.com
Note that a pile of drivers don't seem to take implicit fencing into
account, or at least don't call drm_atoimc_set_fence_for_plane().
Cc'ing relevant people, or at least some. Some drivers also look like
they don't disable implicit fencing (e.g. amdgpu) because the explicit
fences and implicit fences are handled by entirely independent code
paths.
I also wonder whether we shouldn't just make the recommended helpers
the default ones, since a lot of drivers don't bother to handle the
implicit fences at all it seems. The helpers won't blow up even for
non-GEM drivers or GEM drivers which don't fill out the gem bo
pointers in struct drm_framebuffer.
v2: Comments from Eric.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Sinclair Yeh <syeh@vmware.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180405154449.23038-7-daniel.vetter@ffwll.ch
There's nothing tinydrm specific to this, and there's a few more
copies of the same in various other drivers.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: David Airlie <airlied@linux.ie>
Cc: David Lechner <david@lechnology.com>
Cc: "Noralf Trønnes" <noralf@tronnes.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Daniel Stone <daniels@collabora.com>
Cc: Haneen Mohammed <hamohammed.sa@gmail.com>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: "Ville Syrjälä" <ville.syrjala@linux.intel.com>
Reviewed-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Acked-by: David Lechner <david@lechnology.com>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180405154449.23038-3-daniel.vetter@ffwll.ch
Less hits to go through when I git grep over all drivers. These
callbacks are optional.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: VMware Graphics <linux-graphics-maintainer@vmware.com>
Cc: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180405154449.23038-2-daniel.vetter@ffwll.ch
The Lenovo Ideapad Mixx 320 laptop uses a portrait LCD panel, add a
quirk for this.
While at it instead of duplicating the same drm_dmi_panel_orientation_data
for 3 laptops add a generic lcd800x1280_rightside_up orientation_data and
use that for all 3 (including the new Mixx 320 entry).
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180418123642.11088-2-hdegoede@redhat.com
When CONFIG_MMU_NOTIFIER is not enabled, struct mmu_notifier has an
incomplete type definition, which causes build errors.
../drivers/gpu/drm/amd/amdkfd/kfd_priv.h:607:22: error: field 'mmu_notifier' has incomplete type
../include/linux/kernel.h:979:32: error: dereferencing pointer to incomplete type
../include/linux/kernel.h:980:18: error: dereferencing pointer to incomplete type
../drivers/gpu/drm/amd/amdkfd/kfd_process.c:434:2: error: implicit declaration of function 'mmu_notifier_unregister_no_release' [-Werror=implicit-function-declaration]
../drivers/gpu/drm/amd/amdkfd/kfd_process.c:435:2: error: implicit declaration of function 'mmu_notifier_call_srcu' [-Werror=implicit-function-declaration]
../drivers/gpu/drm/amd/amdkfd/kfd_process.c:438:21: error: variable 'kfd_process_mmu_notifier_ops' has initializer but incomplete type
../drivers/gpu/drm/amd/amdkfd/kfd_process.c:439:2: error: unknown field 'release' specified in initializer
../drivers/gpu/drm/amd/amdkfd/kfd_process.c:439:2: warning: excess elements in struct initializer [enabled by default]
../drivers/gpu/drm/amd/amdkfd/kfd_process.c:439:2: warning: (near initialization for 'kfd_process_mmu_notifier_ops') [enabled by default]
../drivers/gpu/drm/amd/amdkfd/kfd_process.c:534:2: error: implicit declaration of function 'mmu_notifier_register' [-Werror=implicit-function-declaration]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Currently if a user requests clock counters for a node without a GPU
resource we will always return EINVAL.
Instead if no GPU resource is attached, fill the gpu_clock_counter
argument with zeroes so that we may proceed and return valid CPU
counters.
Signed-off-by: Andres Rodriguez <andres.rodriguez@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Passing NULL pointer to PTR_ERR will result in return value of 0
indicating success which is clearly not what it is intended here.
This patch returns -EINVAL instead.
v2: change ret code to -ENODEV
Fixes: 5ec7e02854 ("drm/amdkfd: Add ioctls for GPUVM memory management")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
It is not used anymore after last changes and it was not even correct to
begin with as it assumed a 1:1 relation between a CRTC and encoder,
while in fact a CRTC can be attached to multiple encoders.
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-28-enric.balletbo@collabora.com
Currently PSR flush is triggered from CRTC's .atomic_begin() callback,
which is executed after modeset disables and enables and before plane
updates are committed. Since PSR flush and re-enable can be triggered
asynchronously by external sources (input event, delayed work), it can
race with hardware programming done in the aforementioned stages.
This patch blocks the PSR completely before hardware programming part
begins and unblock after it ends. This relies on reference counted PSR
disable introduced with previous patch.
Cc: Kristian H. Kristensen <hoegsberg@chromium.org>
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-27-enric.balletbo@collabora.com
Currently both rockchip_drm_psr_activate() and _deactivate() only set the
boolean "active" flag without actually making sure that hardware state
complies with it.
Since we are going to extend the usage of this API to properly lock PSR
for the duration of atomic commits, we change the semantics in following
way:
- a counter is used to track the number of inhibit requests,
- PSR is actually disabled in hardware on first inhibit request,
- PSR enable work is scheduled on last allow request.
The above allows using the API as a way to deterministically synchronize
PSR state changes with other DRM events, i.e. atomic commits and cursor
updates. As a nice side effect, the naming is sorted out and we have
"inhibit" for stopping the software logic and "enable" for hardware
state.
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-26-enric.balletbo@collabora.com
The first time after we call rockchip_drm_do_flush() after
rockchip_drm_psr_register(), we go from PSR_DISABLE to PSR_FLUSH. The
difference between PSR_DISABLE and PSR_FLUSH is whether or not we have a
delayed work pending - PSR is off in either state. However
psr_set_state() only catches the transition from PSR_FLUSH to
PSR_DISABLE (which never happens), while going from PSR_DISABLE to
PSR_FLUSH triggers a call to psr->set() to disable PSR while it's
already disabled. This triggers the eDP PHY power-on sequence without
being shut down first and this seems to occasionally leave the encoder
unable to later enable PSR. Let's just simplify the state machine and
simply consider PSR_DISABLE and PSR_FLUSH the same state.
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Kristian H. Kristensen <hoegsberg@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-25-enric.balletbo@collabora.com
Driver callbacks, such as system suspend or resume can be called any
time, specifically they can be called before the component bind
callback. Let's use dp->adp pointer as a safeguard and skip calling
Analogix entry points if it is an ERR_PTR().
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-24-enric.balletbo@collabora.com
Some of the platform-specific stuff in rockchip_dp_poweron() needs to
happen before the generic code. Some needs to happen after. Let's
split the callback in two.
Specifically we can't start doing PSR work until _after_ the whole
controller is up, so don't set the enable until the end.
Cc: Kristian H. Kristensen <hoegsberg@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
[seanpaul added exynos change]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-23-enric.balletbo@collabora.com
Some encoder have a crc verification check, crc check fail if
input and output data is not equal.
That means encoder input and output need use same color depth,
vop can output 10bit data to encoder, but some panel only support
8bit depth, that would make crc check die.
So pre dither down vop data to 8bit if panel's bpc is 8.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
[seanpaul resolved conflict in rockchip_drm_vop.c]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-22-enric.balletbo@collabora.com
The comments in analogix_dp_init_aux() claim that we're disabling aux
channel retries, but then right below it for Rockchip it sets them to
3. If we actually need 3 retries for Rockchip then we could adjust
the comment, but it seems more likely that we want the same retry
behavior across all platforms.
Cc: Stéphane Marchesin <marcheu@chromium.org>
Cc: 征增 王 <wzz@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-21-enric.balletbo@collabora.com
The code in analogix_dp_transfer() that was supposed to print out:
AUX CH error happened
Was actually dead code. That's because the previous check (whether
the interrupt status indicated any errors) would have hit for all
errors anyway.
Let's combine the two error checks so we can actually see AUX CH
errors. We'll also downgrade the message to a warning since some of
these types of errors might be expected for some displays. If this
gets too noisy we can downgrade again to debug.
Cc: 征增 王 <wzz@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-20-enric.balletbo@collabora.com
The current user of the analogix power_off is "analogix_dp-rockchip".
That driver does this:
- deactivate PSR
- turn off a clock
Both of these things (especially deactive PSR) should be done before
we turn the PHY power off and turn off analog power. Let's move the
callback up.
Note that without this patch (and with
https://patchwork.kernel.org/patch/9553349/ [seanpaul: this patch was
not applied, but it seems like the race can still occur]), I experienced
an error in reboot testing where one thread was at:
rockchip_drm_psr_deactivate
rockchip_dp_powerdown
analogix_dp_bridge_disable
drm_bridge_disable
...and the other thread was at:
analogix_dp_send_psr_spd
analogix_dp_enable_psr
analogix_dp_psr_set
psr_flush_handler
The flush handler thread was finding AUX channel errors and eventually
reported "Failed to apply PSR", where I had a kgdb breakpoint. Presumably
the device would have eventually given up and shut down anyway, but it
seems better to fix the order to be more correct.
Cc: Kristian H. Kristensen <hoegsberg@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-19-enric.balletbo@collabora.com
It's too early to detect fast link training, if other step after it
failed, we will set fast_link flag to 1, and retry set_bridge again. In
this case we will power down and power up panel power supply, and we
will do fast link training since we have set fast_link flag to 1. In
fact, we should do full link training now, not the fast link training.
So we should move the fast link detection at the end of set_bridge.
Cc: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-18-enric.balletbo@collabora.com
Register ANALOGIX_DP_FUNC_EN_1(offset 0x18), Rockchip is different to
Exynos:
on Exynos edp phy,
BIT 7 MASTER_VID_FUNC_EN_N
BIT 6 reserved
BIT 5 SLAVE_VID_FUNC_EN_N
on Rockchip edp phy,
BIT 7 reserved
BIT 6 RK_VID_CAP_FUNC_EN_N
BIT 5 RK_VID_FIFO_FUNC_EN_N
So, we should do some private operations to Rockchip.
Cc: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-17-enric.balletbo@collabora.com
The STRM_VALID bit in register ANALOGIX_DP_SYS_CTL_3 may be unstable,
so we may hit the error log "Timeout of video streamclk ok" since
checked this unstable bit.
In fact, we can go continue and the streamclk is ok if we wait enough time,
it does no effect on display.
Let's change this error to warn.
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-16-enric.balletbo@collabora.com
There is no register named ANALOGIX_DP_PLL_CTL in Rockchip edp phy reg
list. We should use BIT_4 in ANALOGIX_DP_PD to control the pll power
instead of ANALOGIX_DP_PLL_CTL.
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-15-enric.balletbo@collabora.com
If we failed disable psr, it would hang the display until next psr
cycle coming. So we should restore psr->state when it failed.
Cc: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-14-enric.balletbo@collabora.com
AUX errors are caused by many different reasons. We may not know what
happened in aux channel on failure, so let's reset aux channel if some
errors occurred.
Cc: 征增 王 <wzz@rock-chips.com>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-13-enric.balletbo@collabora.com
There are some different bits between Rockchip and Exynos in register
"AUX_PD". This patch fixes the incorrect operations about it.
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-12-enric.balletbo@collabora.com
We need to check the dpcd write/read return value to see whether the
write/read was successful
Cc: Kristian H. Kristensen <hoegsberg@chromium.org>
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-11-enric.balletbo@collabora.com
Enhanced mode is required by the eDP 1.2 specification, and not doing it
early could result in a period of time where we have a link transmitting
idle packets without it. Since there is no reason to disable it, we just
enable it at the beginning of link training and then keep it on all the
time.
Cc: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-10-enric.balletbo@collabora.com
There was a 1ms delay to detect the hpd signal, which is too short to
detect a short pulse. This patch extends this delay to 100ms.
Cc: Stéphane Marchesin <marcheu@chromium.org>
Cc: 征增 王 <wzz@rock-chips.com>
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-9-enric.balletbo@collabora.com
When panel is shut down, we should make sure edp can be disabled to avoid
undefined behavior.
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-8-enric.balletbo@collabora.com
Following the correct power up sequence:
dp_pd=ff => dp_pd=7f => wait 10us => dp_pd=00
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-7-enric.balletbo@collabora.com
According to DP spec v1.3 chap 3.5.1.2 Link Training, Link Policy Maker
must first detect that the HPD signal is asserted high by the Downstream
Device before establishing a link with it.
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-6-enric.balletbo@collabora.com
When we enable bridge failed, we have to retry it, otherwise we would get
the abnormal display.
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-5-enric.balletbo@collabora.com
