A system bus error during a PDMA send operation can result in bytes being
lost. Theoretically that could cause the target to remain in DATA OUT phase
and the initiator (expecting a phase change) would time-out waiting for the
Last Byte Sent flag. Should that happen, fail the transfer so the core
driver will stop using PDMA with this target.
Cc: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Stan Johnson <userm57@yahoo.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support for Apple's custom "SCSI DMA" chip. This patch doesn't make use
of its DMA capability. Just the PDMA capability is sufficient to improve
sequential read throughput by a factor of 5.
Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: Joshua Thompson <funaho@jurai.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Stan Johnson <userm57@yahoo.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A system bus error during a PDMA transfer can mess up the calculation of
the transfer residual (the PDMA handshaking hardware lacks a byte
counter). This results in data corruption.
The algorithm in this patch anticipates a bus error by starting each
transfer with a MOVE.B instruction. If a bus error is caught the transfer
will be retried. If a bus error is caught later in the transfer (for a
MOVE.W instruction) the transfer gets failed and subsequent requests for
that target will use PIO instead of PDMA.
This avoids the "!REQ and !ACK" error so the severity level of that message
is reduced to KERN_DEBUG.
Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: stable@vger.kernel.org # v4.14+
Fixes: 3a0f64bfa9 ("mac_scsi: Fix pseudo DMA implementation")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reported-by: Chris Jones <chris@martin-jones.com>
Tested-by: Stan Johnson <userm57@yahoo.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some targets introduce delays when handshaking the response to certain
commands. For example, a disk may send a 96-byte response to an INQUIRY
command (or a 24-byte response to a MODE SENSE command) too slowly.
Apparently the first 12 or 14 bytes are handshaked okay but then the system
bus error timeout is reached while transferring the next word.
Since the scsi bus phase hasn't changed, the driver then sets the target
borken flag to prevent further PDMA transfers. The driver also logs the
warning, "switching to slow handshake".
Raise the PDMA threshold to 512 bytes so that PIO transfers will be used
for these commands. This default is sufficiently low that PDMA will still
be used for READ and WRITE commands.
The existing threshold (16 bytes) was chosen more or less at random.
However, best performance requires the threshold to be as low as possible.
Those systems that don't need the PIO workaround at all may benefit from
mac_scsi.setup_use_pdma=1
Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: stable@vger.kernel.org # v4.14+
Fixes: 3a0f64bfa9 ("mac_scsi: Fix pseudo DMA implementation")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Stan Johnson <userm57@yahoo.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A PDMA error is handled in the core driver by setting the device's 'borken'
flag and aborting the command. Unfortunately, do_abort() is not
dependable. Perform a SCSI bus reset instead, to make sure that the command
fails and gets retried.
Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: stable@vger.kernel.org # v4.20+
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Stan Johnson <userm57@yahoo.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The reselection interrupt gets disabled during selection and must be
re-enabled when hostdata->connected becomes NULL. If it isn't re-enabled a
disconnected command may time-out or the target may wedge the bus while
trying to reselect the host. This can happen after a command is aborted.
Fix this by enabling the reselection interrupt in NCR5380_main() after
calls to NCR5380_select() and NCR5380_information_transfer() return.
Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: stable@vger.kernel.org # v4.9+
Fixes: 8b00c3d5d4 ("ncr5380: Implement new eh_abort_handler")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Stan Johnson <userm57@yahoo.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This reverts commit 4822827a69.
The purpose of that commit was to suppress a timeout warning message which
appeared to be caused by target latency. But suppressing the warning is
undesirable as the warning may indicate a messed up transfer count.
Another problem with that commit is that 15 ms is too long to keep
interrupts disabled as interrupt latency can cause system clock drift and
other problems.
Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: stable@vger.kernel.org
Fixes: 4822827a69 ("scsi: ncr5380: Increase register polling limit")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Stan Johnson <userm57@yahoo.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Host reset oopses because it calls wd719x_chip_init, which calls
request_firmware, under a spinlock. Stop the RISC first, then flush active
SCBs under a spinlock. Finally call wd719x_chip_init unlocked.
Also found and fixed more bugs during tests:
Affected active SCBs were not flushed during abort, bus and device
reset. This caused problems in a following host reset (hang or oops).
Device and bus reset failed under load because the result of the reset
command is WD719X_SUE_TERM or WD719X_SUE_RESET. Don't treat these codes as
error in wd719x_wait_done.
wd719x_direct_cmd for RESET/ABORT commands didn't work properly, causing
timeouts. Looks like it was caused by the WD719X_DISABLE_INT bit. Not
setting it for RESET/ABORT commands seems to fix the probem. Also lower
the log level of the corresponding "direct command completed" message to
debug.
Unfortunately, my documentation is missing some pages, including page
67 (SPIDER67.gif) about resets :(
Reported-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Signed-off-by: Ondrej Zary <linux@zary.sk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Several SCSI transport and LLD drivers surround code that does not
tolerate concurrent calls of .queuecommand() with scsi_target_block() /
scsi_target_unblock(). These last two functions use
blk_mq_quiesce_queue() / blk_mq_unquiesce_queue() for scsi-mq request
queues to prevent concurrent .queuecommand() calls. However, that is
not sufficient to prevent .queuecommand() calls from scsi_send_eh_cmnd().
Hence surround the .queuecommand() call from the SCSI error handler with
code that avoids that .queuecommand() gets called in the blocked state.
Note: converting the .queuecommand() call in scsi_send_eh_cmnd() into
code that calls blk_get_request() + blk_execute_rq() is not an option
since scsi_send_eh_cmnd() must be able to make forward progress even
if all requests have been allocated.
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ability to modify the SCSI device state was introduced by commit
638127e579a4 ("[PATCH] Fix error handler offline behaviour"; v2.6.12). That
same commit introduced the following device states:
{ SDEV_CREATED, "created" },
{ SDEV_RUNNING, "running" },
{ SDEV_CANCEL, "cancel" },
{ SDEV_DEL, "deleted" },
{ SDEV_QUIESCE, "quiesce" },
{ SDEV_OFFLINE, "offline" },
The SDEV_BLOCK state was introduced later to avoid that an FC cable pull
would immediately result in an I/O error (commit 1094e682310e; "[PATCH]
suspending I/Os to a device"; v2.6.12). That same patch introduced the
ability to set the SDEV_BLOCK state from user space. I'm not sure whether
that ability was introduced on purpose or accidentally.
Since there is agreement that only writing "running" or "offline" into
the SCSI sysfs device state attribute makes sense, restrict sysfs writes
to these values.
This patch makes sure that SDEV_BLOCK is only used for its original
purpose, namely to allow transport drivers and LLDs to block further
.queuecommand() calls while transport layer or adapter recovery is in
progress.
Note: a web search for "/sys/class/scsi_device" AND "device/state"
revealed several storage configuration guides. The instructions I found
in these guides tell users to write the value "running" or "offline" in
the SCSI device state sysfs attribute and no other values.
[mkp: typo]
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: James Smart <james.smart@broadcom.com>
Cc: Ewan D. Milne <emilne@redhat.com>
Cc: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
IEEE_8021QAZ_APP_SEL_STREAM is a valid selector for iSCSI connections, so
add code to use IEEE_8021QAZ_APP_SEL_STREAM selector to get priority mask.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Adding functionality to allow the SCSI queue depth to be changed by
utilizing the "scsi_change_queue_depth" function.
[mkp: checkpatch]
Signed-off-by: Branden Bonaby <brandonbonaby94@gmail.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
This patch fixes the following warning:
drivers/scsi/mpt3sas/mpt3sas_base.c: In function _base_update_ioc_page1_inlinewith_perf_mode :
drivers/scsi/mpt3sas/mpt3sas_base.c:4510:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (ioc->high_iops_queues) {
^
drivers/scsi/mpt3sas/mpt3sas_base.c:4530:2: note: here
case MPT_PERF_MODE_LATENCY:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable -Wimplicit-fallthrough.
Fixes: 30cb97023f38 ("scsi: mpt3sas: Introduce perf_mode module parameter")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Many times in libsas, and in LLDDs which use libsas, the check for an
expander device is re-implemented or open coded.
Use dev_is_expander() instead. We rename this from
sas_dev_type_is_expander() to not spill so many lines in referencing.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update driver version from 28.100.00.00 to 29.100.00.00
This is equivalent to Phase 10 OOB driver.
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
1. Introduce module parameter perf_mode for only Aero/Sea generation HBAs.
2. Update IOC page1 fields according to performance mode.
Below are the performance modes that can be enabled with module parameter
perf_mode:
0: Balanced - Few high iops reply queues will be enabled. Interrupt
coalescing will be enabled only for these high iops reply descriptor
queues.
1: Iops - Interrupt coalescing will be enabled on all reply queues.
Coalescing timeout is set to 0x20.This is default value for Aero.
2: Latency - Interrupt coalescing will be enabled on all reply queues.
Coalescing timeout is set to 0xA. This is a legacy behavior similar to
Ventura & Invader HBA series.
Default perf mode set by driver will be balanced mode if the following
conditions are met:
- CPU vendor = Intel;
- Aero controller working in 16GT/s pcie speed
Performance mode will be set to latency mode for all other cases.
4k Random Read IO performance numbers on 24 SAS SSD drives for above three
permormance modes. Performance data is from Intel Skylake and HGST SS300
(drive model SDLL1DLR400GCCA1).
IOPs:
-----------------------------------------------------------------------
|perf_mode | qd = 1 | qd = 64 | note |
|-------------|--------|---------|-------------------------------------
|balanced | 259K | 3061k | Provides max performance numbers |
| | | | both on lower QD workload & |
| | | | also on higher QD workload |
|-------------|--------|---------|-------------------------------------
|iops | 220K | 3100k | Provides max performance numbers |
| | | | only on higher QD workload. |
|-------------|--------|---------|-------------------------------------
|latency | 246k | 2226k | Provides good performance numbers |
| | | | only on lower QD worklaod. |
-----------------------------------------------------------------------
Avarage Latency:
-----------------------------------------------------
|perf_mode | qd = 1 | qd = 64 |
|-------------|--------------|----------------------|
|balanced | 92.05 usec | 501.12 usec |
|-------------|--------------|----------------------|
|iops | 108.40 usec | 498.10 usec |
|-------------|--------------|----------------------|
|latency | 97.10 usec | 689.26 usec |
-----------------------------------------------------
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enable interrupt coalescing only on high iops queues.
In ioc config page 1, offset 0x14 (ProductSpecific field) is used to
determine interrupt coalescing enabled/disabled on per reply descriptor
post queue group(8) basis. If 31st bit is zero, then interrupt coalescing
is enabled for all reply descriptor post queues. If 31st bit is set to one,
then user can enable/disable interrupt coalescing on per reply descriptor
post queue group(8) basis. So to enable interrupt coalescing only on first
reply descriptor post queue group (i.e. on high iops queues), set bit 0 and
31.
This configuration should reset during driver unload or shutdown to the
default settings. For this, the driver takes copy of default ioc page 1 and
copies back the default or unmodified ioc page1 during unload and
shutdown. This means that on next driver load (e.g. if older version driver
is loaded by user), current modified changes on ioc page1 won't take
effect.
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
High iops queues are mapped to non-managed irqs. Set affinity of
non-managed irqs to local numa node. Low latency queues are mapped to
managed irqs.
Driver reserves some reply queues for max iops (through
pci_alloc_irq_vectors_affinity and .pre_vectors interface). The rest of
queues are for low latency.
Based on io workload in io submission path, driver will decide which group
of reply queues (either high iops queues or low latency queues) to be
used. High iops queues will be mapped to local numa node of controller and
low latency queues will be mapped to cpus across numa nodes. In general,
high iops and low latency queues should fit into 128 reply queues
which is the max number of reply queues supported by Aero/Sea.
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the IO submission path _base_get_msix_index is called twice. Initially
while getting the smid and subsequently while posting the request
descriptor (RD).
Refactor code to query msix index only while posting the request
descriptor. Save determined msix index in msix_io field.
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver will use round-robin method for io submission in batches within
the high iops queues when the number of in-flight ios on the target device
is larger than 8. Otherwise the driver will use low latency reply queues.
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Code refactoring.
In function _base_get_msix_index, add scmd as second argument. This change
is made in preparation for the next patch where we introduce a new function
to get the MSI-X index for high iops queues.
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Aero controllers support balanced performance mode through the ability to
configure queues with different properties.
Reply queues with interrupt coalescing enabled are called "high iops reply
queues" and reply queues with interrupt coalescing disabled are called "low
latency reply queues".
The driver configures a combination of high iops and low latency reply
queues if:
- HBA is an AERO controller;
- MSI-X vectors supported by the HBA is 128;
- Total CPU count in the system more than high iops queue count;
- Driver is loaded with default max_msix_vectors module parameter; and
- System booted in non-kdump mode.
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the Aero HBA supports Atomic Request Descriptors, it sets the Atomic
Request Descriptor Capable bit in the IOCCapabilities field of the IOCFacts
Reply message. Driver uses an Atomic Request Descriptor as an alternative
method for posting an entry onto a request queue.
The posting of an Atomic Request Descriptor is an atomic operation,
providing a safe mechanism for multiple processors on the host to post
requests without synchronization. This Atomic Request Descriptor format is
identical to first 32 bits of Default Request Descriptor and uses only 32
bits.
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This code refactoring introduces function pointers.
Host uses Request Descriptors of different types for posting an entry onto
a request queue. Based on controller type and capabilities, host can also
use atomic descriptors other than normal descriptors. Using function
pointer will avoid if-else statements
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove including <linux/version.h> that don't need it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use existing macros. No functional change.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Checkpatch emits a warning when using symbolic permissions. Use octal
permissions instead. No functional change.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Support is easier with all driver parameters visible in sysfs.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warnings:
drivers/scsi/megaraid/megaraid_sas_base.c: In function megasas_fw_crash_buffer_show:
drivers/scsi/megaraid/megaraid_sas_base.c:3138:16: warning: variable buff_addr set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_sas_base.c: In function megasas_get_pd_list:
drivers/scsi/megaraid/megaraid_sas_base.c:4426:13: warning: variable ci_h set but not used [-Wunused-but-set-variable]
'buff_addr' is never used since inroduction in commit fc62b3fc90
("megaraid_sas : Firmware crash dump feature support")
'ci_h' is not used since commit 9b3d028f34 ("scsi: megaraid_sas:
Pre-allocate frequently used DMA buffers")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/megaraid/megaraid_sas_base.c: In function megasas_create_frame_pool:
drivers/scsi/megaraid/megaraid_sas_base.c:4124:6: warning: variable sge_sz set but not used [-Wunused-but-set-variable]
It's not used any more since commit 200aed582d ("megaraid_sas: endianness
related bug fixes and code optimization")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When building powerpc pseries_defconfig or powernv_defconfig:
drivers/scsi/lpfc/lpfc_nvmet.c:224:1: error: unused function
'lpfc_nvmet_get_ctx_for_xri' [-Werror,-Wunused-function]
drivers/scsi/lpfc/lpfc_nvmet.c:246:1: error: unused function
'lpfc_nvmet_get_ctx_for_oxid' [-Werror,-Wunused-function]
These functions are only compiled when CONFIG_NVME_TARGET_FC is enabled.
Use that same condition so there is no more warning. While the fixes commit
did not introduce these functions, it caused these warnings.
Fixes: 4064b27417a7 ("scsi: lpfc: Make some symbols static")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
clang warns:
drivers/scsi/ibmvscsi/ibmvscsi.c:2126:7: warning: variable 'rc' is used
uninitialized whenever switch case is taken [-Wsometimes-uninitialized]
case IBMVSCSI_HOST_ACTION_NONE:
^~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/ibmvscsi/ibmvscsi.c:2151:6: note: uninitialized use occurs
here
if (rc) {
^~
Initialize rc in the IBMVSCSI_HOST_ACTION_UNBLOCK case statement then
shuffle IBMVSCSI_HOST_ACTION_NONE down to the default case statement and
make it return early so that rc is never used uninitialized in this
function.
Fixes: 035a3c4046b5 ("scsi: ibmvscsi: redo driver work thread to use enum action states")
Link: https://github.com/ClangBuiltLinux/linux/issues/502
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Suggested-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix sparse warnings:
drivers/scsi/lpfc/lpfc_sli.c:115:1: warning: symbol 'lpfc_sli4_pcimem_bcopy' was not declared. Should it be static?
drivers/scsi/lpfc/lpfc_sli.c:7854:1: warning: symbol 'lpfc_sli4_process_missed_mbox_completions' was not declared. Should it be static?
drivers/scsi/lpfc/lpfc_nvmet.c:223:27: warning: symbol 'lpfc_nvmet_get_ctx_for_xri' was not declared. Should it be static?
drivers/scsi/lpfc/lpfc_nvmet.c:245:27: warning: symbol 'lpfc_nvmet_get_ctx_for_oxid' was not declared. Should it be static?
drivers/scsi/lpfc/lpfc_init.c:75:10: warning: symbol 'lpfc_present_cpu' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warnings:
drivers/scsi/lpfc/lpfc_init.c: In function lpfc_setup_cq_lookup:
drivers/scsi/lpfc/lpfc_init.c:9359:30: warning: variable qp set but not used [-Wunused-but-set-variable]
It's not used since commit e70596a60f88 ("scsi: lpfc: Fix poor use of
hardware queues if fewer irq vectors")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For v3 hw, stash is enabled to promote performance, but it does little to
improve performance according to current tests. What's more, it causes
exceptions for some situations, so disable it.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Several error codes will be generated between PHY down to up.
This issue was introduced by HW design. The designers came to the
conclusion that we should ignore these errors.
Signed-off-by: Jiaxing Luo <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It reports a error as follows from some tools at two places in our code:
runtime error: left shift of 4 by 29 places cannot be represented in type
'int' So change the type of the two numbers to unsigned to avoid the error.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Macro HISI_SAS_SGE_PAGE_CNT is defined to SG_CHUNK_SIZE, which is 128.
This means that sizeof(struct hisi_sas_slot_buf_table) is 4192. This is
just over a 4K, which can mean inefficient DMA memory usage (for no PI).
Reduce the size of HISI_SAS_SGE_PAGE_CNT to 124 to fit in a 4K page. With
this change, we experience no performance hit.
Cc: dann frazier <dann.frazier@canonical.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The argument of dev_err() called by multi_bit_ecc_error_process_v3_hw() is
not right. We pass two arguments, but there is only one printk format
specifier in the string.
Also move the print format string to dev_err().
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When removing the driver or when probe fails, we need to delete the PHY
timers.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warnings:
drivers/scsi/megaraid/megaraid_sas_base.c: In function megasas_suspend:
drivers/scsi/megaraid/megaraid_sas_base.c:7269:20: warning: variable host set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_sas_base.c: In function megasas_aen_polling:
drivers/scsi/megaraid/megaraid_sas_base.c:8397:15: warning: variable wait_time set but not used [-Wunused-but-set-variable]
'host' never used since introduction in commit 31ea708897 ("[SCSI]
megaraid_sas: add hibernation support")
'wait_time' never used since commit 11c71cb4ab ("megaraid_sas: Do
not allow PCI access during OCR")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/megaraid/megaraid_sas_base.c: In function megasas_transition_to_ready:
drivers/scsi/megaraid/megaraid_sas_base.c:3900:6: warning: variable cur_state set but not used [-Wunused-but-set-variable]
Never used since commit 7218df69e3 ("[SCSI] megaraid_sas: use the
firmware boot timeout when waiting for commands")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In _ctl_ioctl_main(), 'ioctl_header' is fetched the first time from
userspace. 'ioctl_header.ioc_number' is then checked. The legal result is
saved to 'ioc'. Then, in condition MPT3COMMAND, the whole struct is fetched
again from the userspace. Then _ctl_do_mpt_command() is called, 'ioc' and
'karg' as inputs.
However, a malicious user can change the 'ioc_number' between the two
fetches, which will cause a potential security issues. Moreover, a
malicious user can provide a valid 'ioc_number' to pass the check in first
fetch, and then modify it in the second fetch.
To fix this, we need to recheck the 'ioc_number' in the second fetch.
Signed-off-by: Gen Zhang <blackgod016574@gmail.com>
Acked-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently auto-hibernate is activated if host supports auto-hibern8
capability. However error-handling is not implemented, which makes the
feature somewhat risky.
If either "Hibernate Enter" or "Hibernate Exit" fail during auto-hibernate
flow, the corresponding interrupt "UIC_HIBERNATE_ENTER" or
"UIC_HIBERNATE_EXIT" shall be raised according to UFS specification.
This patch adds auto-hibernate error-handling:
- Monitor "Hibernate Enter" and "Hibernate Exit" interrupts after
auto-hibernate feature is activated.
- If a failure happens, trigger error-handling just like
"manual-hibernate" failure and apply the same recovery flow: schedule
UFS error handler in ufshcd_check_errors(), and then do host reset and
restore in UFS error handler.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some vendor-specific initialization flow may set its own auto-hibernate
timer. In this case, do not overwrite timer value as "default value" in
ufshcd_init().
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The checking of Auto-Hibernation support is used in many places in the
driver, thus re-factor it as ufshcd_is_auto_hibern8_supported() to make
code more clean.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since we are processing events synchronously now, the second call of
sas_ex_join_wide_port() in sas_ex_discover_dev() is not needed. There will
be no races with other works in disco workqueue. So remove the second
sas_ex_join_wide_port().
I did not change the return value of 'res' to error when discover failed
because we need to continue to discover other phys if one phy discover
failed. So let's keep that logic as before and just add a debug log to
detect the failure. And directly return if second fanout expander attatched
to the parent expander because it has nothing to do after the phy is
disabled.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
