Related-to: commit 325fb5b4d2
The compat path suffers from a similar problem. It only uses a __be32
when all of the recent code uses, and expects, an nf_inet_addr
everywhere. As a result, addresses stored by xt_recents were
filled with whatever other stuff was on the stack following the be32.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
With a minor compile fix from Roman.
Reported-and-tested-by: Roman Hoog Antink <rha@open.ch>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch adds missing role attribute to the DCCP type, otherwise
the creation of entries is not of any use.
The attribute added is CTA_PROTOINFO_DCCP_ROLE which contains the
role of the conntrack original tuple.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Commit d0dba725 (netfilter: ctnetlink: add callbacks to the per-proto
nlattrs) changed the protocol registration function to abort if the
to-be registered protocol doesn't provide a new callback function.
The DCCP and UDP-Lite IPv6 protocols were missed in this conversion,
add the required callback pointer.
Reported-and-tested-by: Steven Jan Springl <steven@springl.ukfsn.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Fix this build error caused by 362b76edb7
"8390p: Get rid of init_module/cleanup_module"
drivers/net/8390p.c:94:19: error: invalid suffix "p_init_module" on integer constant
drivers/net/8390p.c:94: error: expected identifier or '(' before numeric constant
drivers/net/8390p.c:99:20: error: invalid suffix "p_cleanup_module" on integer constant
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Ursula Braun <ubraun@linux.vnet.ibm.com>
net/iucv/af_iucv.c in net-next-2.6 is almost correct. 4 lines should
still be deleted. These are the remaining changes:
Signed-off-by: David S. Miller <davem@davemloft.net>
The SO_MSGLIMIT socket option modifies the message limit for new
IUCV communication paths.
The message limit specifies the maximum number of outstanding messages
that are allowed for connections. This setting can be lowered by z/VM
when an IUCV connection is established.
Expects an integer value in the range of 1 to 65535.
The default value is 65535.
The message limit must be set before calling connect() or listen()
for sockets.
If sockets are already connected or in state listen, changing the message
limit is not supported.
For reading the message limit value, unconnected sockets return the limit
that has been set or the default limit. For connected sockets, the actual
message limit is returned. The actual message limit is assigned by z/VM
for each connection and it depends on IUCV MSGLIMIT authorizations
specified for the z/VM guest virtual machine.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the skb cannot be copied to user iovec, always return -EFAULT.
The skb is enqueued again, except MSG_PEEK flag is set, to allow user space
applications to correct its iovec pointer.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides the socket type SOCK_SEQPACKET in addition to
SOCK_STREAM.
AF_IUCV sockets of type SOCK_SEQPACKET supports an 1:1 mapping of
socket read or write operations to complete IUCV messages.
Socket data or IUCV message data is not fragmented as this is the
case for SOCK_STREAM sockets.
The intention is to help application developers who write
applications or device drivers using native IUCV interfaces
(Linux kernel or z/VM IUCV interfaces).
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow 'classification' of socket data that is sent or received over
an af_iucv socket. For classification of data, the target class of an
(native) iucv message is used.
This patch provides the cmsg interface for iucv_sock_recvmsg() and
iucv_sock_sendmsg(). Applications can use the msg_control field of
struct msghdr to set or get the target class as a
"socket control message" (SCM/CMSG).
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch allows to send and receive data in the parameter list of an
iucv message.
The parameter list is an arry of 8 bytes that are used by af_iucv as
follows:
0..6 7 bytes for socket data and
7 1 byte to store the data length.
Instead of storing the data length directly, the difference
between 0xFF and the data length is used.
This convention does not interfere with the existing use of PRM
messages for shutting down the send direction of an AF_IUCV socket
(shutdown() operation). Data lenghts greater than 7 (or PRM message
byte 8 is less than 0xF8) denotes to special messages.
Currently, the special SEND_SHUTDOWN message is supported only.
To use IPRM messages, both communicators must set the IUCV_IPRMDATA
flag during path negotiation, i.e. in iucv_connect() and
path_pending().
To be compatible to older af_iucv implementations, sending PRM
messages is controlled by the socket option SO_IPRMDATA_MSG.
Receiving PRM messages does not depend on the socket option (but
requires the IUCV_IPRMDATA path flag to be set).
Sending/Receiving data in the parameter list improves performance for
small amounts of data by reducing message_completion() interrupts and
memory copy operations.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide the socket operations getsocktopt() and setsockopt() to enable/disable
sending of data in the parameter list of IUCV messages.
The patch sets respective flag only.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the af_iucv communication partner quiesces the path to shutdown its
receive direction, provide a quiesce callback implementation to shutdown
the (local) send direction. This ensures that both sides are synchronized.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the IUCV commands can be invoked in interrupt context.
Those commands need a different per-cpu IUCV command parameter block,
otherwise they might overwrite an IUCV command parameter of a not yet
finished IUCV command invocation in process context.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SME needs to be notified when the authentication or association
attempt times out and MLME has stopped processing in order to allow
the SME to decide what to do next.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The maximum sleep interval, for powersave purposes, is
determined by the DTIM period (it may not be larger)
and the required networking latency (it must be small
enough to fulfil those constraints).
This makes mac80211 calculate the maximum sleep interval
based on those constraints, and pass it to the driver.
Then the driver should instruct the device to sleep at
most that long.
Note that the device is responsible for aligning the
maximum sleep interval between DTIMs, we make sure it's
not longer but it needs to make sure it's between them.
Also, group some powersave documentation together and
make it more explicit that we support managed mode only,
and no IBSS powersaving (yet).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make the JOIN_IBSS command look at the beacon interval
attribute to see if the user requested a specific beacon
interval, if not default to 100 TU (wext too).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just setting IEEE80211_CONF_CHANGE_PS should be sufficient
for changes in the power saving things. The driver already
tells us whether it wants notification of dynps via the
"have dynps support" hw flag.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stephen Rothwell reported these warnings from a 32-bit build:
net/mac80211/mlme.c:1771: warning: left shift count >= width of type
net/mac80211/mlme.c:1772: warning: left shift count >= width of type
net/mac80211/mlme.c:1773: warning: left shift count >= width of type
net/mac80211/mlme.c:1774: warning: left shift count >= width of type
net/mac80211/mlme.c:1775: warning: left shift count >= width of type
This shows a bug in my code -- BIT(X) uses just "1 << X" which means
a 32-bit integer on 32-bit platforms, but the code here needs a u64
on all platforms. Fix this by using "1ULL << X" instead of BIT(X).
Thanks Stephen!
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Private structure is allocated by wiphy_new now, so use
wiphy_free instead of kfree.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rndis_wext_link_change() might be called from rndis_command() at
initialization stage and priv->workqueue/priv->work have not been
initialized yet. This causes invalid opcode at rndis_wext_bind on
some brands of bcm4320.
Fix by initializing workqueue/workers in rndis_wext_bind() before
rndis_command is used.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sparse complains, correctly, about these:
drivers/net/wireless/rndis_wlan.c:418:21: warning: symbol 'rndis_config_ops' was not declared. Should it be static?
drivers/net/wireless/rndis_wlan.c:423:6: warning: symbol 'rndis_wiphy_privid' was not declared. Should it be static?
Fix that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the RCU locking here we sleep while in an atomic context,
since we can sleep just use mutex locking for the interface
list instead of RCU. Sorry, seems I didn't get that in my UML
test.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow user to config the device all the time but only allow commiting
these changes to card if the card is up and running.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch removes the "manual radio disable" parameter
as there is no usage scenario of disabling radio using this module parameter.
User can use iwconfig's txpower to enable and disable radio.
This module parameter also does not work as expected. During module load
the status of radio is set, the radio is not actually disabled. Even so,
the moment mac80211 requests the interface to be up the radio will be
enabled again.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Function rs_stay_in_table was flushing the rate scale table way to early. time_after
macro in expecting long value and was failing because we passing u32 value.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch clean up the code for NL80211_IFTYPE_MONITOR mode,
priv->iw_mode is set in add_interface, but add_interface is never called
for monitor mode.
The only way mac80211 informs us about monitor mode is through
configuring filter; since iw_mode will never set to
NL80211_IFTYPE_MONITOR, modify and remove all the code refer to
NL80211_IFTYPE_MONITOR and replace with iwl_is_monitor_mode() function
call.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch calculates interrupt statistics for debugfs.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch adds debugfs to 3945. Also fix debugfs registration in iwlagn
to return error code if it fails.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If passive scanning is requested we should not ask the
microcode to do active scanning after detecting traffic
on a channel -- that should only be used when an active
scan is requested but some channels are marked passive.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This modifies iwlwifi to
* no longer build its own probe request, but use mac80211's
* therefore, support arbitrary scan IEs (up to the max len)
* support multiple scan SSIDs
* support passive scanning
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This limit applies to current (APIv1 and APIv2) 3945 firmware only, not
supported firmware of any of the other cards.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With this patch ar9170 is capable of receiving aggregated 802.11n frames
and sniffing on most networks without having a "debug message overhead".
(Includes phy initialization requested by
Johannes Berg <johannes@sipsolutions.net> -- JWL)
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TIM IE must not be shorter than 4 bytes, so verify that
when parsing it and use the proper type. To ease that adjust
struct ieee80211_tim_ie to have a virtual bitmap of size
at least 1.
Also check that the TIM IE is actually present before trying
to parse it!
Because other people may need the function, make it a static
inline in ieee80211.h.
(The original "mac80211: validate TIM IE length" was a minimal fix for
2.6.30. This purports to be the full, correct fix. -- JWL)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The fact that these are exported is a technical detail
of the conversion period -- we don't want anybody to
start relying on these. Ultimately we want things to
use cfg80211 only, and once everything that is in wext
is converted to cfg80211 drivers will not need to touch
wext _at all_.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we leave an IBSS, we should clear the SSID and not just the
BSSID, but since WEXT allows configuring while the interface is
down we must not clear it when leaving due to taking the iface
down, so some complications are needed.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new nl80211 attributes that can be used with NL80211_CMD_SET_WIPHY
and NL80211_CMD_GET_WIPHY to manage fragmentation/RTS threshold and
retry limits.
Since these values are stored in struct wiphy, remove the local copy
from mac80211 where feasible (frag & rts threshold). The retry limits
are currently needed in struct ieee80211_conf, but these could be
eventually removed since the driver should have access to the values
in struct wiphy.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for configuring HT40 channels
and receiving HT40 to ar9170. Receiving aggregation
doesn't seem to work right now, so it's not enabled.
Same goes for TX aggregation, but that probably needs
even more work.
With this, I can receive roughly 33 Mbits/sec.
The HT capabilities are a little odd, I tried following
otus here -- in particular having SGI_40 but not SGI_20
is a little weird but afaict that's what otus does.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Supporting wireless extension nickname is pointless
and no other modern driver supports this, so remove
it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Trying to separate header files into net/wireless.h and
net/cfg80211.h has been a source of confusion. Remove
net/wireless.h (because there also is the linux/wireless.h)
and subsume everything into net/cfg80211.h -- except the
definitions for regulatory structures which get moved to
a new header net/regulatory.h.
The "new" net/cfg80211.h is now divided into sections.
There are no real changes in this patch but code shuffling
and some very minor documentation fixes.
I have also, to make things reflect reality, put in a
copyright line for Luis to net/regulatory.h since that
is probably exclusively written by him but was formerly
in a file that only had my copyright line.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This converts mac80211 to the new cfg80211 IBSS API, the
wext handling functions are called where appropriate.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds IBSS API along with (preliminary) wext handlers.
The wext handlers can only do IBSS so you need to call them
from your own wext handlers if the mode is IBSS.
The nl80211 API requires
* an SSID
* a channel (frequency) for the case that a new IBSS
has to be created
It optionally supports
* a flag to fix the channel
* a fixed BSSID
The cfg80211 code also takes care to leave the IBSS before
the netdev is set down. If wireless extensions are used, it
also caches values when the interface is down and instructs
the driver to join when the interface is set up.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we have ->deauth and ->disassoc we can support the
wext SIWMLME call directly without driver wext handlers.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When listing all wireless netdevs in the system this
is useful to print which wiphy they belong to. Just
add the attribute, any program that doesn't care will
just ignore it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch sets IEEE80211_TX_CTL_CLEAR_PS_FILT for outgoing
frames for a half-wake station.
this is necessary if one wants to get ps-poll working properly with a p54 ap.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PS-Polled frames must be sent with OUT_NOCANCEL flag set,
or the firmware will reject all of them, at the station is still blacklisted.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The following patch implements some control over the LED on RTL8187B and
RTL8187L devices. Triggers are registered for TX and RX. Whenever the
trigger event occurs, the LED is turned off for 1/20 second, then turned
back on.
Note: For those RTL8187X devices that are built into the computer and have
a LED that is expected to be controlled with a radio switch, this patch will
not operate that LED. That will take a separate patch to be prepared later.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can allow scan requests in AP mode as long as the interface has not
yet been configured to send out Beacon frames (or if beaconing has
been disabled prior to the scan request). This makes it easier to scan
for neighboring BSSes during AP initialization and makes it possible
to run a scan without setting the interface down, if needed. Without
this change, the only available option would be to set the interface
down, move into station mode, and set the interface up, prior to
requesting the scan.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
